TOEPIA LX ARMREST ASSEMBLY INSTRUCTION 1) Align the aluminum rail and slide through the base rail 2) Place the aluminum end-plate and secure it with 2 screws 8
TOEPIA Spa Specifications 2 1/2 4 3/4 6 3/4 43 14 If back flow prevent device is required by plumbing code in your state, it must be supplied by plumber 43L x 28W x 54H Due to continuous improvements on all our product, All specifications, characteristics, packing, colors, design are subject to change without notice. 9
TOEPIA LX Spa Specification 56 33 21 1 19 21 / 5 3 8 3 3 / 4 53 14 W ALL If backflow prevent is required by pllumbing code in your state, it must be supplied by the plumber. 30 1 Relaxed pillow LX Sliding armrest Chair: 42.5L x 22.75W x 20.25H, Shipping Weight: 109 lbs Base: 55L x 34.5W x 23H, Shipping Weight: 133 lbs Footrest Air controller Faucet On/Off switch Operation Switches Whirlpool System Massage System Power Source Drain Optional Power Drain Plumbing Source Warranty On/Off air activated switch One Pipe-Less motor with two discharge ports Milticolor LED Light 12V, 3.2Amp, 60Hz 120V AC, 15Amp, 60Hz, two outlets Dedicated circuit (GFCI protected hard wired) P-TRAP Installed 1.5 inches 115V, 3.2Amp, 60Hz Discharge Pump Hot & Cold Water: 0.5 in (Fitting included) One year (parts & labor) within 48 Contiguous States 25 1 32 1 Due to continuous improvements on all our product, All specifications, characteristics, packing, colors, design are subject to change without notice. 10
Plumbing Connections All plumbing connections should be made by a qualified, licensed plumber in accordance with local plumbing and building codes. Hot and Cold Water Supply Lines Connect 1/2 ID supply tubes to a fresh water source. Shut-off valves should be utilized. Electrical Connections The Foot spa must be plugged into a GFCI protected outlet, installed by a licensed electrician. Testing the Foot spa Clean the tub and fill with water to the wave-mark (water level) on the wall of the tub. When the tub is filled with water, turn the switch on the front of the pedicure spa to activate the whirlpool pump. Water should be coming out of the jets and the Air Bleed spout. Check for whirlpool leaks. After checking under the tub for leaks, use the same switch to turn the whirlpool pump off and drain the tub basin by opening the overflow/waste control handle and turning on the Power Drain Pump if installed. Cleaning and Care of Your Foot spa Between Each Customer Drain all water and remove debris from the pedicure spa. Clean the surfaces and walls of the Foot spa with soap or detergent and rinse with clean, clear water Disinfect with an EPA-registered disinfectant. Wipe out with a clean towel. Flushing of the Whirlpool System It is extremely important to flush the whirlpool system of the foot spa to prevent harmful bacteria from growing and to prolong the life of your pedicure spa Remove the Suction Fitting Cover with a phillips screwdriver Scrub the suction cover with a non chlorine bleach Totally immerse the suction Fitting cover in an EPA-registered disinfectant and scrub. Replace the Suction Fitting Cover with a screwdriver. Do not over tighten the mounting screw. Do not run the pedicure spa whirlpool jets without the Suction Fitting Cover in place. Fill the tub basin near the wave mark on the rear wall with hot water. Turn the whirlpool jets on. Add 3 (three) teaspoons of low foaming crystal dishwasher detergent and 2 (two) ounces of household bleach to the tub basin. Run whirlpool for 10-15 minutes and drain the tub basin. Fill the tub basin near the wave mark on the rear wall with cold water. Run the whirlpool jets for 5 minutes and drain the tub basin. Clean the pedicure spa with a soft cloth and a mild detergent. Weekly Disinfecting Procedure of the Whirlpool System After following the outlined procedures for daily cleaning, fill the pedicure spa tub with hot water and 4 (four) teaspoons of 5% bleach solution. Circulate the solution through the whirlpool system for 5-10 minutes. Let the solution sit overnight (at least 6-10 hours). The following morning (before the first customer) run the foot spa for 5 minutes and drain. Follow the procedure Flushing of the Whirlpool System. 11
To Open GeniJet Cleaning Procedure 1. Gently turn the cover counter clockwise to remove it. 2. Use anti-bacterial soap or a solution of 3% hydrogen peroxide to wipe the inner chamber. DO NOT use chlorine or chlorinated products (such as diluted bleach) as this will damage the plastics and VOID your warranty. 3. Clean air supply line by gently sliding a qtip (dipped in 3% hydrogen peroxide) into the air canal. 4. Replace the cap by gently turning it clockwise until snug (no need to over-tighten) *Keep the motor impller must be free of debris, any build-up within the impeller reduces the motor action and may cause damage to the Genieye motor. Dimensions: Specifications: Model: GeniJet Motor: 1.2A @ 120 VAC; 60 Hz; 55 W (GFI Receptacle) 0.1HP @ 3600HP magnetically coupled motor Pump: Dual jet with adjustable airflow White premium grade ABS house with removable jet cap Mounting: Single 3.50 hole Auto tightening mounting screw 12