Service Literature Corp. 00-L8 Revised 05/08 KGA/KG09 through 50 KGA/KG UNITS 7.5 to.5 ton 6. to 4 kw The KGA/KG 7.5, 8.5, 0 and.5 ton (09, 0, 0, 50) packaged gas units are available in standard cooling efficiency. Units are available in 0,000, 80,000 or 40,000tuh (8., 5.7 or 70. kw) heating inputs. Gas heat sections are designed with aluminized steel tube heat exchangers. All KGA/KG units are designed to accept any of several different energy management thermostat control systems with minimum field wiring. Factory- or field-provided control options connect to the unit with jack plugs. When plugged in the controls become an integral part of the unit wiring. Information contained in this manual is intended for use by qualified service technicians only. All specifications are subject to change. Procedures outlined in this manual are presented as a recommendation only and do not supersede or replace local or state codes. If the unit must be lifted for service, rig unit by attaching four cables to the holes located in the unit base rail (two holes at each corner). Refer to the installation instructions for the proper rigging technique. WARNING Improper installation, adjustment, alteration, service or maintenance can cause property damage, personal injury or loss of life. Installation and service must be performed by a qualified installer or service agency. ELECTROSTATIC DISCHARGE (ESD) Precautions and Procedures CAUTION Electrostatic discharge can affect electronic components. Take precautions to neutralize electrostatic charge by touching your hand and tools to metal prior to handling the control. CAUTION As with any mechanical equipment, contact with sharp sheet metal edges can result in personal injury. Take care while handling this equipment and wear gloves and protective clothing. WARNING Electric shock hazard. Can cause injury or death. efore attempting to perform any service or maintenance, turn the electrical power to unit OFF at disconnect switch(es). Unit may have multiple power supplies. Options / Accessories... Page Specifications... Page 5 High Altitude... Page 9 lower Data... Page 0 Electrical Data... Page 6 Parts Arrangement... Page 0 I- Unit Components... Page II- Placement and Installation... Page III- Start-Up... Page IV- Charging... Page 5 V- System Service Checks... Page 45 VI- Maintenance... Page 46 VII- Accessories... Page 48 VIII-Wiring Diagrams... Page 56 Page 08.
OPTIONS / ACCESSORIES Item Description Model Number Catalog Number Unit Model No 09 0 0 50 COOLING SYSTEM Condensate Drain Trap PVC - CTRAP0AD 76W6 X X X X Copper - CTRAP0AD 76W7 X X X X Corrosion Protection Factory O O O O Drain Pan Overflow Switch KSNSR7A- 74W4 X X X X Efficiency High O O O O Standard O O O O Low Ambient Kit KSNSR- 54W6 X X X X Refrigerant Type R-40A O O O O HEATING SYSTEM ottom Gas Piping Kit CGPKT0-0 54W95 X X X X Combustion Air Intake Extensions TEXTN0AN 9W5 X X X X Gas Heat Input 0,000 tuh Factory O O O O 80,000 tuh Factory O O O O 40,000 tuh Factory O O O O Low Temperature Vestibule Heater 08/0V-ph - CLTVH0-Y X6 X X X X 460V - CLTVH0-G X64 X X X X 575V - CLTVH0-J X65 X X X X LPG/Propane Conversion Kits Standard Heat - CPROPS 4N X X X X Medium Heat - CPROPS 4N X X X X High Heat - CPROPS 4N5 X X X X Stainless Steel Heat Exchanger Factory O O O O Vertical Vent Extension CEXTN0 4W6 X X X X LOWER - SUPPLY AIR lower Option CAV (Constant Air Volume) Factory O O O O MSAV (Multi-Stage Air Volume) Factory O O O O lower Motors elt Drive - hp Factory O O O O elt Drive - hp Factory O O O O elt Drive - 5 hp Factory O O O O VFD Manual ypass Kit (for MSAV equipped units only) KVFDC- 90W5 X X X X Drive Kits Kit # 590-890 rpm Factory O O O O See lower Data Tables for selection Kit # 800-05 rpm Factory O O O O Kit # 795-95 rpm Factory O O O O Kit #4 70-970 rpm Factory O O O O Kit #5 940-00 rpm Factory O O O O Kit #6 05-00 rpm Factory O O O O Kit #0 900-5 rpm Factory O O O O Kit # 040-5 rpm Factory O O O O Kit # 5-45 rpm Factory O O O O CAINET Combination Coil/Hail Guards CGARD5- T05 X X X X Hinged Access Panels Factory O O O O Horizontal harge Kit KHECK00-5W5 X X X X Return Air Adaptor Plate (for L Series and T-Class replacement) CCONV0-54W96 X X X X NOTE - Catalog and model numbers shown are for ordering field installed accessories. OX - Configure To Order (Factory Installed) or Field Installed O = Configure To Order (Factory Installed) X = Field Installed Page
OPTIONS / ACCESSORIES Item Description Model Number Catalog Number Unit Model No 09 0 0 50 CONTROLS Commercial Controls L Connection uilding Automation System - - - X X X X ACnet K0CTRL- 96W5 OX OX OX OX ACnet Sensor with Display K0SNSR0FF 97W X X X X ACnet Sensor without Display K0SNSR00FF 97W4 X X X X Novar 05 K0CTRL0-96W OX OX OX OX Plenum Cable (75 ft.) K0MISC00FF 97W5 X X X X Smoke Detector - Supply or Return (Power board and one sensor) CSNSR44- K76 X X X X Smoke Detector - Supply and Return (Power board and two sensors) CSNSR4- K80 X X X X INDOOR AIR QUALITY Air Filters Healthy Climate High Efficiency Air Filters MERV 8 - CFLTR5-50W6 X X X X 0 x 5 x (Order 4 per unit) MERV - CFLTR40-5W4 X X X X Replacement Media Filter With Metal Mesh Frame CFLTR0-- Y06 X X X X (includes non-pleated filter media) Indoor Air Quality (CO ) Sensors Sensor - Wall-mount, off-white plastic cover with LCD display C0SNSR50AEL 77N9 X X X X Sensor - Wall-mount, off-white plastic cover, no display C0SNSR5AEL 87N5 X X X X Sensor - lack plastic case with LCD display, rated for plenum mounting C0SNSR5AEL 87N5 X X X X Sensor - Wall-mount, black plastic case, no display, rated for plenum mounting C0MISC9AE 87N54 X X X X CO Sensor Duct Mounting Kit - for downflow applications C0MISC9AE- 85L4 X X X X Aspiration ox - for duct mounting non-plenum rated CO sensors (87N5 or 77N9) UVC Germicidal Lamps C0MISC6AE- 90N4 X X X X Healthy Climate UVC Light Kit (08/0v-ph) CUVCL0-54W6 X X X X ELECTRICAL Voltage 60 hz 08/0V - phase Factory O O O O 460V - phase Factory O O O O 575V - phase Factory O O O O onnect Switch - See Electrical/Electric Heat tables for selection 80 amp - CDISC080-54W56 OX OX OX OX 50 amp - CDISC50-54W57 OX OX OX OX GFI Service Outlets 5 amp non-powered, field-wired (08/0V, 460V only) LTAGFIK0/5 74M70 OX OX OX OX 0 amp non-powered, field-wired (575V only) CGFCI0FF 67E0 X X X X Weatherproof Cover for GFI CGFCI99FF 0C89 X X X X Lamps operate on 0-0V single-phase power supply. Step-down transformer may be ordered separately for 460V and 575V units. Alternately, 0V power supply may be used to directly power the UVC ballast(s) NOTE - Catalog and model numbers shown are for ordering field installed accessories. OX - Configure To Order (Factory Installed) or Field Installed O = Configure To Order (Factory Installed) X = Field Installed Page
OPTIONS / ACCESSORIES Item Description Model Number Catalog Number Unit Model No 09 0 0 50 ECONOMIZER Standard Economizer (Not for Title 4) Standard Economizer with Single Temperature Control KECON0- U45 OX OX OX OX Downflow or Horizontal Applications - Includes arometric Relief Dampers and Air Hoods Standard Economizer Controls (Not for Title 4) Single Enthalpy Control CSNSR64FF 5W64 OX OX OX OX Differential Enthalpy Control (order ) CSNSR64FF 5W64 X X X X High Performance Economizer (Approved for California Title 4 uilding Standards / AMCA Class A Certified) High Performance Economizer with Single Temperature Control KECON- 0U58 OX OX OX OX Downflow or Horizontal Applications - Includes arometric Relief Dampers and Air Hoods High Performance Economizer Controls (Not for Title 4) Single Enthalpy Control CSNSR60FF 0Z75 OX OX OX OX Differential Enthalpy Control (order ) CSNSR60FF 0Z75 X X X X Horizontal Low Profile arometric Relief Dampers With Exhaust Hood Horizontal Low Profile arometric Relief Dampers With Exhaust Hood LAGEDH0/5 5K04 X X X X OUTDOOR AIR Outdoor Air Dampers With Outdoor Air Hood Motorized CDAMP0-4G8 OX OX OX OX Manual CDAMP0-4G9 OX OX OX OX POWER EXHAUST Standard Static 08/0V-ph - KPWRE0-Y 5W44 X X X X 460V-ph - KPWRE0-G 5W45 X X X X 575V-ph - KPWRE0-J 5W46 X X X X ROOF CURS Hybrid Roof Curbs, Downflow 8 in. height CCUR70- F54 X X X X 4 in. height CCUR7- F55 X X X X 8 in. height CCUR7- F56 X X X X 4 in. height CCUR7- F57 X X X X Adjustable Pitch Curb 4 in. height CCUR55-54W50 X X X X CEILING DIFFUSERS Step-Down - Order one RTD-95S K6 X RTD-5S K6 X X RTD-85S K6 X Flush - Order one FD-95S K56 X FD-5S K57 X X FD-85S K58 X Transitions (Supply and Return) - Order one CDIFF0- X65 X CDIFF- X66 X X CDIFF- X67 X NOTE - Catalog and model numbers shown are for ordering field installed accessories. OX - Configure To Order (Factory Installed) or Field Installed O = Configure To Order (Factory Installed) X = Field Installed Page 4
SPECIFICATIONS 7.5 TON General Data Nominal Tonnage 7.5 Ton 7.5 Ton 7.5 Ton 7.5 Ton Model Number KG09S4 KGA09S4M KGA09H4 KGA09H4M Efficiency Type Standard Standard High High lower Type Constant Air Volume (CAV) MSAV (Multi- Stage Air Volume) Constant Air Volume (CAV) MSAV (Multi- Stage Air Volume) Cooling Gross Cooling Capacity - tuh 87,800 88,00 9,000 9,000 Performance Net Cooling Capacity - tuh 86,000 86,000 90,000 90,000 AHRI Rated Air Flow - cfm 400 000 000 800 Total Unit Power - kw 7.8 7.8 7. 7. EER (tuh/watt).0.0.5.5 IEER (tuh/watt).7.0.0 4.0 Refrigerant Type R-40A R-40A R-40A R-40A Refrigerant Charge Furnished Circuit 4 lbs. 0 oz. 4 lbs. 0 oz. 6 lbs. oz. 6 lbs. oz. Circuit lbs. 6 oz. lbs. 6 oz. 7 lbs. oz. 7 lbs. oz. Gas Heating Options Available - See page 7 Standard ( stage), Medium ( Stage), High ( Stage) Compressor Type (number) Scroll () Scroll () Scroll () Scroll () Outdoor Coils (Fin/Tube) Outdoor Coil Fans Indoor Coils Indoor lower and Drive Selection Net face area (total) - sq. ft. 0.9 0.9 8.0 8.0 Number of rows Fins per inch 0 0 Motor - (No.) hp () / () / () / () / Motor rpm 075 075 075 075 Total Motor watts 740 740 800 800 Diameter - (No.) in. () 4 () 4 () 4 () 4 Number of blades Total Air volume - cfm 8800 8800 8800 8800 Net face area (total) - sq. ft..78.78.78.78 Tube diameter - in. /8 /8 /8 /8 Number of rows 4 4 Fins per inch 4 4 4 4 Drain connection - Number and size () in. NPT coupling Expansion device type Refrigerant Metering Orifice (RFC) alance port TXV, removable head Nominal motor output hp, hp, 5 hp Maximum usable motor output. hp,.45 hp, 5.75 hp (US Only) Motor - Drive kit number hp Kit 590-890 rpm Kit 800-05 rpm Kit 795-95 rpm hp Kit 4 70-970 rpm Kit 5 940-00 rpm Kit 6 05-00 rpm 5 hp Kit 0 900-5 rpm Kit 040-5 rpm Kit 5-45 rpm lower wheel nominal diameter x width - in. () 5 X 5 () 5 X 5 () 5 X 5 () 5 X 5 Filters Type of filter Disposable Number and size - in. (4) 0 x 5 x Electrical characteristics 08/0V, 460V or 575V - 60 hertz - phase NOTE - Net capacity includes evaporator blower motor heat deduction. Gross capacity does not include evaporator blower motor heat deduction. AHRI Certified to AHRI Standard 40/60; 95 F outdoor air temperature and 80 F db/67 F wb entering evaporator air; minimum external duct static pressure. Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor output required. Maximum usable output of motors furnished are shown. In Canada, nominal motor output is also maximum usable motor output. If motors of comparable output are used, be sure to keep within the service factor limitations outlined on the motor nameplate. NOTE Units equipped with MSAV (Multi-Stage Air Volume) option are limited to a motor service factor of.0. Page 5
SPECIFICATIONS 8.5 TON General Data Nominal Tonnage 8.5 Ton 8.5 Ton 8.5 Ton 8.5 Ton Model Number KG0S4 KGA0S4M KGA0H4 KGA0H4M Efficiency Type Standard Standard High High lower Type Constant Air Volume (CAV) MSAV (Multi-Stage Air Volume) Constant Air Volume (CAV) MSAV (Multi-Stage Air Volume) Cooling Gross Cooling Capacity - tuh 99,600 99,600 0,800 0,800 Performance Net Cooling Capacity - tuh 97,000 97,000 00,000 00,000 AHRI Rated Air Flow - cfm 800 400 400 400 Total Unit Power - kw 8.8 8.8 8. 8. EER (tuh/watt).0.0.. IEER (tuh/watt).7.0.9 4.0 Refrigerant Type R-40A R-40A R-40A R-40A Refrigerant Charge Furnished Circuit 4 lbs. 5 oz. 4 lbs. 5 oz. 6 lbs. 8 oz. 6 lbs. 8 oz. Circuit 4 lbs. oz. 4 lbs. oz. 6 lbs. 5 oz. 6 lbs. 5 oz. Gas Heating Options Available - See page 7 Standard ( stage), Medium ( Stage), High ( Stage) Compressor Type (number) Scroll () Scroll () Scroll () Scroll () Outdoor Coils (Fin/Tube) Outdoor Coil Fans Indoor Coils Indoor lower and Drive Selection Net face area (total) - sq. ft. 0.9 0.9 8.0 8.0 Number of rows Fins per inch 0 0 Motor - (No.) hp () / () / () / () / Motor rpm 075 075 075 075 Total Motor watts 740 740 800 800 Diameter - (No.) in. () 4 () 4 () 4 () 4 Number of blades Total Air volume - cfm 8800 8800 8800 8800 Net face area (total) - sq. ft..78.78.78.78 Tube diameter - in. /8 /8 /8 /8 Number of rows 4 4 Fins per inch 4 4 4 4 Drain connection - Number and size () in. NPT coupling Expansion device type Refrigerant Metering Orifice (RFC) alance port TXV, removable head Nominal motor output hp, hp, 5 hp Maximum usable motor output. hp,.45 hp, 5.75 hp (US Only) Motor - Drive kit number hp Kit 590-890 rpm Kit 800-05 rpm Kit 795-95 rpm hp Kit 4 70-970 rpm Kit 5 940-00 rpm Kit 6 05-00 rpm 5 hp Kit 0 900-5 rpm Kit 040-5 rpm Kit 5-45 rpm lower wheel nominal diameter x width - in. () 5 X 5 () 5 X 5 () 5 X 5 () 5 X 5 Filters Type of filter Disposable Number and size - in. (4) 0 x 5 x Electrical characteristics 08/0V, 460V or 575V - 60 hertz - phase NOTE - Net capacity includes evaporator blower motor heat deduction. Gross capacity does not include evaporator blower motor heat deduction. AHRI Certified to AHRI Standard 40/60; 95 F outdoor air temperature and 80 F db/67 F wb entering evaporator air; minimum external duct static pressure. Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor output required. Maximum usable output of motors furnished are shown. In Canada, nominal motor output is also maximum usable motor output. If motors of comparable output are used, be sure to keep within the service factor limitations outlined on the motor nameplate. NOTE Units equipped with MSAV (Multi-Stage Air Volume)MSAV (Multi-Stage Air Volume) option are limited to a motor service factor of.0. Page 6
SPECIFICATIONS 0 TON General Data Nominal Tonnage 0 Ton 0 Ton 0 Ton 0 Ton Model Number KG0S4 KGA0S4M KGA0H4 KGA0H4M Efficiency Type Standard Standard High High lower Type Constant Air Volume (CAV) MSAV (Multi-Stage Air Volume) Constant Air Volume (CAV) MSAV (Multi-Stage Air Volume) Cooling Gross Cooling Capacity - tuh 8,000 8,400,000,000 Performance Net Cooling Capacity - tuh 5,000 5,000 8,000 8,000 AHRI Rated Air Flow - cfm 000 800 600 00 Total Unit Power - kw 0.5 0.5 9.8 9.8 EER (tuh/watt).0.0 IEER (tuh/watt).7.0.8 Refrigerant Type R-40A R-40A R-40A R-40A Refrigerant Charge Furnished Circuit 5 lbs. oz. 4 lbs. oz. 7 lbs. 4 oz. 7 lbs. 4 oz. Circuit 5 lbs. 6 oz. 4 lbs. 0 oz. 7 lbs. 8 oz. 7 lbs. 8 oz. Gas Heating Options Available - See page 7 Standard ( stage), Medium ( Stage), High ( Stage) Compressor Type (number) Scroll () Scroll () Scroll () Scroll () Outdoor Coils (Fin/Tube) Outdoor Coil Fans Indoor Coils Indoor lower and Drive Selection Net face area (total) - sq. ft. 8.0 8.0 8.0 8.0 Number of rows Fins per inch 0 0 Motor - (No.) hp () / () / () / () / Motor rpm 075 075 075 075 Total Motor watts 690 690 800 800 Diameter - (No.) in. () 4 () 4 () 4 () 4 Number of blades Total Air volume - cfm 900 900 8800 8800 Net face area (total) - sq. ft..78.78.54.54 Tube diameter - in. /8 /8 /8 /8 Number of rows 4 4 4 Fins per inch 4 4 4 4 Drain connection - Number and size () in. NPT coupling Expansion device type Refrigerant Metering Orifice (RFC) alance port TXV, removable head Nominal motor output hp, hp, 5 hp Maximum usable motor output. hp,.45 hp, 5.75 hp (US Only) Motor - Drive kit number hp Kit 590-890 rpm Kit 800-05 rpm Kit 795-95 rpm hp Kit 4 70-970 rpm Kit 5 940-00 rpm Kit 6 05-00 rpm 5 hp Kit 0 900-5 rpm Kit 040-5 rpm Kit 5-45 rpm lower wheel nominal diameter x width - in. () 5 X 5 () 5 X 5 () 5 X 5 () 5 X 5 Filters Type of filter Disposable Number and size - in. (4) 0 x 5 x Electrical characteristics 08/0V, 460V or 575V - 60 hertz - phase NOTE - Net capacity includes evaporator blower motor heat deduction. Gross capacity does not include evaporator blower motor heat deduction. AHRI Certified to AHRI Standard 40/60; 95 F outdoor air temperature and 80 F db/67 F wb entering evaporator air; minimum external duct static pressure. Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor output required. Maximum usable output of motors furnished are shown. In Canada, nominal motor output is also maximum usable motor output. If motors of comparable output are used, be sure to keep within the service factor limitations outlined on the motor nameplate. NOTE Units equipped with MSAV (Multi-Stage Air Volume)MSAV (Multi-Stage Air Volume) option are limited to a motor service factor of.0. Page 7
SPECIFICATIONS.5 TON General Data Nominal Tonnage.5 Ton.5 Ton Model Number KG50S4 KG50S4M Efficiency Type Standard Standard lower Type Constant Air Volume (CAV) MSAV (Multi-Stage Air Volume) Cooling Gross Cooling Capacity - tuh 46,000 46,000 Performance Net Cooling Capacity - tuh 40,000 40,000 AHRI Rated Air Flow - cfm 950 950 Total Unit Power - kw.0.0 EER (tuh/watt) 0.8 0.8 IEER (tuh/watt)..5 Refrigerant Type R-40A R-40A Refrigerant Charge Furnished Circuit lbs. oz. lbs. oz. Circuit lbs. 5 oz. lbs. 5 oz. Gas Heating Options Available - See page 7 Standard ( stage), Medium ( Stage), High ( Stage) Compressor Type (number) Scroll () Scroll () Outdoor Coils (Fin/Tube) Outdoor Coil Fans Indoor Coils Indoor lower and Drive Selection Net face area (total) - sq. ft. 5.9 5.9 Number of rows Fins per inch 0 0 Motor - (No.) hp () / () / Motor rpm 075 075 Total Motor watts 050 050 Diameter - (No.) in. () 4 () 4 Number of blades Total Air volume - cfm 9700 9700 Net face area (total) - sq. ft..54.54 Tube diameter - in. /8 /8 Number of rows 4 4 Fins per inch 4 4 Drain connection - Number and size () in. NPT coupling Expansion device type Refrigerant Metering Orifice (RFC) Nominal motor output hp, hp, 5 hp Maximum usable motor output. hp,.45 hp, 5.75 hp (US Only) Motor - Drive kit number hp Kit 590-890 rpm Kit 800-05 rpm Kit 795-95 rpm hp Kit 4 70-970 rpm Kit 5 940-00 rpm Kit 6 05-00 rpm 5 hp Kit 0 900-5 rpm Kit 040-5 rpm Kit 5-45 rpm lower wheel nominal diameter x width - in. () 5 X 5 () 5 X 5 Filters Type of filter Disposable Number and size - in. (4) 0 x 5 x Electrical characteristics 08/0V, 460V or 575V - 60 hertz - phase NOTE - Net capacity includes evaporator blower motor heat deduction. Gross capacity does not include evaporator blower motor heat deduction. AHRI Certified to AHRI Standard 40/60; 95 F outdoor air temperature and 80 F db/67 F wb entering evaporator air; minimum external duct static pressure. Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor output required. Maximum usable output of motors furnished are shown. In Canada, nominal motor output is also maximum usable motor output. If motors of comparable output are used, be sure to keep within the service factor limitations outlined on the motor nameplate. NOTE Units equipped with MSAV (Multi-Stage Air Volume)MSAV (Multi-Stage Air Volume) option are limited to a motor service factor of.0. Page 8
SPECIFICATIONS - GAS HEAT Gas Heating Performance Recommended Gas Supply Pressure - in. w.g. Heat Input Type Standard Medium High Number of Gas Heat Stages Input - tuh First Stage 84,500 7,000 56,000 Second Stage 0,000 80,000 40,000 Output - tuh Second Stage 04,000 44,000 9000 Temperature Rise Range - F 5-45 0-60 40-70 Thermal Efficiency 80% 80% 80% Gas Supply Connections /4 in NPT /4 in NPT /4 in NPT Natural 7 7 7 LPG/Propane HIGH ALTITUDE DERATE Units may be installed at altitudes up to 000 feet above sea level without any modification. At altitudes above 000 feet, units must be derated to match gas manifold pressures shown in table below. At altitudes above 4500 feet unit must be derated % for each 000 feet above sea level. NOTE This is the only permissible derate for these units. Gas Heat Type Input Rate Gas Manifold Pressure Altitude Natural Gas or LPG/Propane Natural Gas LPG/Propane Gas First Stage Second Stage ft. In. w.g. In. w.g. tuh tuh Standard 00-4500.4 9.6 84,500 4,000 Medium 00-4500.4 9.6 7,000 7,000 High 00-4500.4 9.6 56,000 0,000 Page 9
LOWER DATA 09S STANDARD EFFICIENCY ELT DRIVE LOWER ASE UNIT LOWER TALE INCLUDES RESISTANCE FOR ASE UNIT ONLY (NO HEAT SECTION) WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: Wet indoor coil air resistance of selected unit. Any factory installed options air resistance (heat section, economizer, etc.) Any field installed accessories air resistance (duct resistance, diffuser, etc.) Then determine from blower table blower motor output required. See page 4 for blower motors and drives. See page 4 for wet coil and option/accessory air resistance data. MAXIMUM STATIC PRESSURE WITH GAS HEAT -.0 in. w.g. Total Air Volume cfm Total Static Pressure in. w.g. 0. 0.4 0.6 0.8.0..4.6.8..4.6 RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP 750 608 0.05 65 0.0 696 0.06 744 0. 794 0.60 845 0.95 894.4 94.8 978.47 047.66 0.89 79.5 0.40 000 65 0.07 657 0.05 70 0.0 748 0.6 797 0.7 846.05 89.0 9.45 977.55 049.75 4.00 8. 4.47 50 64 0.09 664 0.07 707 0.4 75 0.50 800 0.84 847.5 89.8 94.5 979.65 05.86 6. 8.6 8.6 500 6 0. 67 0.09 74 0.9 758 0.64 80 0.97 849.6 89.48 96.6 98.75 05.96 4. 84.49 4.77 750 64 0. 680 0. 7 0.45 76 0.78 807.09 85.7 896.58 940.74 989.88 05.08.4 85.6 44.9 000 65 0.5 689 0.9 78 0.6 770 0.9 8. 856.49 90.70 947.87 996.0 055. 0.47 86.78 48.0 50 66 0.7 698 0.46 77 0.78 777.09 89.8 86.6 908.84 955.0 004.7 059.6.6 89.94 5.8 500 67 0.6 708 0.65 746 0.95 786.5 87.5 870.78 96.99 965.7 0. 065.5 6.79 9. 57.47 750 684 0.56 79 0.85 756.4 795.4 86.70 880.95 97.6 976.4 0.5 07.7.98 98. 6.67 4000 697 0.78 7.05 768.4 807.6 848.89 89. 940.4 988.5 04.7 08.9 4.9 05.5 70.89 450 70.00 745.7 78.55 89.8 86.09 906. 954.55 00.74 046.9 094.4 5.4 4.76 78 4. Page 0
LOWER DATA 09H AND 0H HIGH EFFICIENCY ELT DRIVE LOWER ASE UNIT LOWER TALE INCLUDES RESISTANCE FOR ASE UNIT ONLY (NO HEAT SECTION) WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: Wet indoor coil air resistance of selected unit. Any factory installed options air resistance (heat section, economizer, etc.) Any field installed accessories air resistance (duct resistance, diffuser, etc.) Then determine from blower table blower motor output required. See page 4 for blower motors and drives. See page 4 for wet coil and option/accessory air resistance data. MAXIMUM STATIC PRESSURE WITH GAS HEAT -.0 in. w.g. Total Air Volume cfm Total Static Pressure in. w.g. 0. 0.4 0.6 0.8.0..4.6.8.0..4.6 RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP 750 48 0. 549 0.4 68 0.57 688 0.7 758 0.8 84 0.9 885.08 94. 99.9 08.54 08.68 4.8 66.95 000 49 0.9 56 0.47 69 0.64 700 0.77 768 0.9 8.0 89.7 946. 995.49 04.66 085.8 6.97 67. 50 507 0.7 574 0.56 64 0.7 7 0.86 779 0.99 84. 900.8 95.44 00.6 045.78 088.95 8. 68. 500 5 0.46 588 0.64 657 0.8 77 0.95 79.09 85.4 909.4 960.57 007.74 050.9 09. 0.9 70.48 750 57 0.56 604 0.74 674 0.9 74.06 806. 865.6 90.5 969.7 04.89 055.08 095.7.47 7.66 000 554 0.67 6 0.86 69.0 760.8 8.4 878.5 9.68 979.86 0.06 06.6 099.46 6.65 74.85 50 57 0.78 64 0.98 7.5 778. 88.49 89.66 94.84 989.0 00.4 068.45 05.65 4.85 78.06 500 59 0.9 66. 7. 798.47 855.65 907.8 956.0 000. 09.44 076.65.86 46.07 8.7 750 64.04 687.8 756.47 88.65 87.8 9.0 970. 0.4 049.65 084.87 8.09 5.9 89.5 4000 69. 7.48 780.66 88.8 890.0 99. 984.44 0.66 059.89 09. 6. 60.54 97.77 450 667.4 74.69 805.86 859.0 909. 956.45 998.68 06.9 070.5 0.7 5.59 69.8 07 4.05 Page
LOWER DATA 0S AND 0S (MSAV) STANDARD EFFICIENCY ELT DRIVE LOWER ASE UNIT LOWER TALE INCLUDES RESISTANCE FOR ASE UNIT ONLY (NO HEAT SECTION) WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: Wet indoor coil air resistance of selected unit. Any factory installed options air resistance (heat section, economizer, etc.) Any field installed accessories air resistance (duct resistance, diffuser, etc.) Then determine from blower table blower motor output required. See page 4 for blower motors and drives. See page 4 for wet coil and option/accessory air resistance data. MAXIMUM STATIC PRESSURE WITH GAS HEAT -.0 in. w.g. Total Air Volume cfm Total Static Pressure in. w.g. 0. 0.4 0.6 0.8.0..4.6.8..4.6 RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP 000 59 0. 66 0.07 68 0.0 7 0. 784 0.60 840 0.96 898.6 948.8 996.47 045.57 09.7 40.9 88. 50 604 0.5 645 0. 690 0.5 79 0.9 790 0.74 846.08 90.4 95.48 00.57 05.70 00.86 49.09 97.4 500 65 0.9 655 0.5 699 0.0 747 0.55 797 0.89 85.0 906.44 959.58 009.68 059.8 08.0 58.6 06.5 750 66 0. 666 0.9 709 0.7 755 0.7 805.0 858. 9.55 966.70 07.8 067.97 7.7 66.44 5.7 000 67 0.7 677 0.4 79 0.55 764 0.87 8.8 866.45 90.67 975.8 06.96 076. 6.5 76.6 5.9 50 650 0. 688 0.4 70 0.7 775.04 8.4 875.60 90.8 985.97 06. 086. 6.54 86.8 5. 500 66 0.5 700 0.6 74 0.9 786. 84.50 886.76 94.96 997.4 048. 097.5 47.75 96.04 45.5 750 676 0.57 74 0.84 754. 798.4 846.68 899.9 956.4 00. 060.5 09.7 58.98 07.7 55.58 4000 69 0.79 78.05 768. 8.6 860.88 94. 97.4 0.5 07.7.95 69. 8.5 66.8 450 706.0 74.8 78.55 87.8 876.09 9. 987.55 07.76 085.97.0 8.47 9.76 77 4.08 4500 7.7 759.5 799.78 844.05 894. 949.56 00.79 05.00 098. 45.46 9.7 4 4.0 89 4.4 4750 79.5 776.77 87.0 86.0 9.56 968.8 00.04 066.7.49 58.74 05 4.0 5 4.0 0 4.6 5000 757.79 794.04 85.0 88.56 94.8 988.08 06. 08.55 5.78 7 4.0 8 4.9 65 4.59 4.89 Page
LOWER DATA 0S (CAV) AND 0H HIGH EFFICIENCY AND 50S STANDARD EFFICIENCY ELT DRIVE LOWER ASE UNIT LOWER TALE INCLUDES RESISTANCE FOR ASE UNIT ONLY (NO HEAT SECTION) WITH DRY INDOOR COIL AND AIR FILTERS IN PLACE. FOR ALL UNITS ADD: Wet indoor coil air resistance of selected unit. Any factory installed options air resistance (heat section, economizer, etc.) Any field installed accessories air resistance (duct resistance, diffuser, etc.) Then determine from blower table blower motor output required. See page 4 for blower motors and drives. See page 4 for wet coil and option/accessory air resistance data. MAXIMUM STATIC PRESSURE WITH GAS HEAT -.0 in. w.g. Total Air Volume cfm Total Static Pressure in. w.g. 0. 0.4 0.6 0.8.0..4.6.8.0..4.6 RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP RPM HP 000 497 0.5 558 0.44 64 0.6 694 0.74 764 0.85 80 0.99 889.6 94.4 994.5 045.7 096.89 46.08 97.7 50 5 0.4 57 0.5 68 0.68 708 0.8 776 0.94 89.09 896.6 948.45 998.64 048.8 098.0 49. 00.4 500 57 0.44 589 0.6 654 0.78 7 0.9 789.05 850. 904.9 955.58 00.77 05.96 0.4 5. 0.5 750 545 0.55 606 0.7 67 0.88 740.0 804.7 86.4 94.5 96.7 00.9 057.0 05.9 54.47 06.68 000 564 0.66 66 0.84 69.0 759.6 89. 874.49 94.68 97.88 07.08 06.6 0.44 58.6 08.8 50 585 0.79 648 0.98 74.4 778. 86.48 887.66 95.86 98.06 06.6 07.45 7.6 6.80.00 500 607 0.9 67. 77. 798.48 85.66 90.85 948.05 99.6 07.46 08.65 5.8 7.0. 750 6.0 698. 76.50 89.67 869.86 95.05 96.5 005.47 049.68 09.88 6.05 8.4.45 4000 660.0 76.5 787.70 88.87 885.06 90.6 974.48 08.7 06.9 05. 49.0 94.49 45.7 450 69.5 755.75 80.9 857.07 90.7 945.50 990.74 04.98 077.0 0.9 6.58 0.79 6 4.0 4500 74.78 78.98 8. 874.8 97.50 96.75 006.0 05.7 094.49 7.70 8.89 8 4. 8 4.8 4750 757.05 809.0 85. 89.5 95.76 980.05 05. 070.59.8 56 4.0 0 4.4 49 4.47 0 4.75 5000 787. 8.4 870.57 90.78 954.06 000.8 046.68 09.95 5 4.9 78 4.40 4 4.6 7 4.86 5 5. 550 84.55 85.66 889.8 90.09 975.4 0.76 070 4.08 5 4.5 59 4.59 0 4.8 48 5.0 97 5.7 50 5.5 5500 85.78 87.9 909. 95.44 999.8 049 4.8 096 4.5 4 4.79 86 5.0 9 5.4 75 5.46 4 5.69 - - - - - - 5750 854.0 890.9 90.48 977.86 07 4.7 078 4.66 6 4.99 7 5.6 4 5.49 58 5.70 - - - - - - - - - - - - - - - - - - 6000 87.6 90.5 955.90 006 4.4 060 4.80 5.9 58 5.5 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 650 890.57 94.94 985 4.4 04 4.9 096 5.8 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Page
FACTORY INSTALLED ELT DRIVE KIT SPECIFICATIONS Nominal hp Maximum hp Drive Kit Number RPM Range. 590-890. 800-05. 795-95.45 4 70-970.45 5 940-00.45 6 05-00 5 5.75 0 900-5 5 5.75 040-5 5 5.75 5-45 NOTE - Using total air volume and system static pressure requirements determine from blower performance tables rpm and motor output required. Maximum usable output of motors furnished are shown. In Canada, nominal motor output is also maximum usable motor output. If motors of comparable output are used, be sure to keep within the service factor limitations outlined on the motor nameplate. NOTE Units equipped with MSAV (Multi-Stage Air Volume)option are limited to a motor service factor of.0. POWER EXHAUST FAN PERFORMANCE Return Air System Static Pressure Air Volume Exhausted in. w.g. cfm 0 75 0.05 955 0.0 685 0.5 40 0.0 65 0.5 90 0.0 40 0.5 00 FACTORY INSTALLED OPTIONS/FIELD INSTALLED ACCESSORY AIR RESISTANCE - in. w.g. Air Gas Heat Exchanger Filters Wet Indoor Coil Return Air Volume Standard Medium High Economizer MERV 8 MERV Adaptor Plate cfm 09, 0 0, 50 Heat Heat Heat 750 0.04 0.04 0.06 0.0 0.0 0.05 0.0 0.0 0.00 000 0.05 0.05 0.07 0.05 0.06 0.06 0.0 0.0 0.00 50 0.06 0.06 0.07 0.07 0.08 0.08 0.0 0.04 0.00 500 0.07 0.07 0.09 0.0 0. 0. 0.0 0.05 0.00 750 0.08 0.08 0.09 0. 0. 0. 0.0 0.05 0.00 000 0.0 0.09 0. 0. 0. 0. 0.0 0.06 0.0 50 0. 0.0 0. 0.5 0.6 0.5 0.0 0.06 0.0 500 0. 0. 0. 0.6 0.7 0.5 0.0 0.07 0.04 750 0.4 0. 0.4 0.9 0.0 0.5 0.0 0.08 0.07 4000 0.5 0.4 0.4 0. 0. 0.9 0.04 0.08 0.09 450 0.7 0.5 0.4 0.4 0.8 0.9 0.04 0.09 0. 4500 0.9 0.7 0.5 0.6 0. 0. 0.04 0.09 0. 4750 0.0 0.8 0.6 0.9 0.7 0.5 0.05 0.0 0.6 5000 0. 0.0 0.6 0.4 0.4 0.9 0.06 0.0 0.8 550 0.4 0. 0.6 0.7 0.47 0. 0.06 0. 0.9 5500 0.5 0. 0.8 0.44 0.54 0.4 0.07 0. 0. 5750 0.7 0.5 0.9 0.49 0.59 0.45 0.07 0. 0.5 6000 0.9 0.7 0.0 0.54 0.64 0.5 0.08 0. 0.7 Page 4
LOWER DATA CEILING DIFFUSERS AIR RESISTANCE - in. w.g. Unit Size 09 Models 0 & 0 Models 50 Models Air Volume cfm RTD Step-Down Diffuser Ends Open Page 5 Side, Ends Open All Ends & Sides Open FD Flush Diffuser 400 0. 0.8 0.5 0.4 600 0.4 0. 0.8 0.7 800 0.7 0.4 0. 0.0 000 0. 0.9 0.5 0.5 00 0.4 0.7 0. 0. 400 0.50 0.45 0.9 0.7 600 0.6 0.54 0.48 0.44 800 0.7 0.6 0.57 0.5 600 0.6 0.8 0. 0.5 800 0.40 0. 0.6 0.8 4000 0.44 0.6 0.9 0. 400 0.49 0.40 0. 0.4 4400 0.54 0.44 0.7 0.7 4600 0.60 0.49 0.4 0. 4800 0.65 0.5 0.46 0.5 5000 0.69 0.58 0.50 0.9 500 0.75 0.6 0.54 0.4 400 0. 0.9 0.6 0.0 4400 0.8 0.4 0.0 0. 4600 0.4 0.9 0.4 0.5 4800 0.40 0.4 0.9 0.9 5000 0.46 0.9 0.4 0. 500 0.5 0.44 0.9 0.7 5400 0.58 0.49 0.4 0. 5600 0.64 0.54 0.47 0.5 5800 0.70 0.59 0.5 0.9 CEILING DIFFUSER AIR THROW DATA Model No. 09 Models 0, 0 Models 50 Models Air Volume Effective Throw Range RTD Step-Down FD Flush cfm ft. ft. 600 4-9 9-4 800 5-0 0-8 000 7 - - 9 00 8-5 - 9 400 0-7 - 0 600 5 - - 9 800 7-5 - 0 4000 9-7 4-400 - 40 6-5 4400 4-4 8-7 5600 9-49 8-7 5800 4-5 9-8 6000 44-54 40-50 600 45-55 4-5 6400 46-55 4-5 6600 47-56 45-56 Throw is the horizontal or vertical distance an air stream travels on leaving the outlet or diffuser before the maximum velocity is reduced to 50 ft. per minute. Four sides open.
ELECTRICAL DATA 7.5 TON 7.5 TON STANDARD EFFICIENCY (R-40A) KGA/KG09S4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps. 6. 4.4 Locked Rotor Amps 8. 4 Compressor Rated Load Amps. 6. 4.4 Outdoor Fan Motors () Power Exhaust () 0. HP Locked Rotor Amps 8. 4 Full Load Amps.4. (total) (4.8) (.6) () Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Horsepower 5 5 5 Motor Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Maximum Unit Only 50 50 60 5 5 0 5 0 0 Overcurrent With () 0. HP Protection Power Exhaust 50 60 70 5 5 0 0 0 5 Minimum Unit Only 4 45 5 0 5 5 6 9 Circuit With () 0. HP Ampacity Power Exhaust 45 48 55 6 6 7 0 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. 7.5 TON HIGH EFFICIENCY (R-40A) KGA09H4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps.6 5.5 4.7 Locked Rotor Amps 86 7 4 Compressor Rated Load Amps.6 5.5 4.7 Locked Rotor Amps 86 7 4 Outdoor Fan Motors () Power Exhaust () 0. HP Full Load Amps.4. (total) (4.8) (.6) () Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Motor Maximum Overcurrent Protection Minimum Circuit Ampacity Horsepower 5 5 5 Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Unit Only 45 50 60 0 5 0 0 0 5 With () 0. HP Power Exhaust 50 50 60 5 5 0 0 0 5 Unit Only 9 4 49 9 0 4 6 7 0 With () 0. HP Power Exhaust 4 44 5 0 5 7 8 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 6
ELECTRICAL DATA 8.5 TON 8.5 TON STANDARD EFFICIENCY (R-40A) kga/kg0s4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 4.5 6. 6 Locked Rotor Amps 98 55 4 Compressor Rated Load Amps 4.5 6. 6 Outdoor Fan Motors () Power Exhaust () 0. HP Locked Rotor Amps 98 55 4 Full Load Amps.4. (total) (4.8) (.6) () Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Horsepower 5 5 5 Motor Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Maximum Unit Only 50 60 70 5 5 0 0 5 5 Overcurrent With () 0. HP 60 60 70 5 5 0 5 5 5 Protection Power Exhaust Minimum Unit Only 45 49 55 5 9 0 Circuit With () 0. HP 48 5 58 7 0 Ampacity Power Exhaust NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. 8.5 TON HIGH EFFICIENCY (R-40A) KGA0H4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 5.5 4.7 Locked Rotor Amps 86 7 4 Compressor Rated Load Amps 5.5 4.7 Locked Rotor Amps 86 7 4 Outdoor Fan Motors () Power Exhaust () 0. HP Full Load Amps.4. (total) (4.8) (.6) () Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Motor Maximum Overcurrent Protection Minimum Circuit Ampacity Horsepower 5 5 5 Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Unit Only 45 50 60 0 5 0 0 0 5 With () 0. HP Power Exhaust 50 50 60 5 5 0 0 0 5 Unit Only 8 4 48 9 0 4 6 7 0 With () 0. HP Power Exhaust 40 4 5 0 5 7 8 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 7
ELECTRICAL DATA 0 TON 0 TON STANDARD EFFICIENCY (R-40A) KGA/KG0S4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps.5 8 5 Locked Rotor Amps 09 59 40 Compressor Rated Load Amps.5 8 5 Outdoor Fan Motors () Power Exhaust () 0. HP Locked Rotor Amps 09 59 40 Full Load Amps.4. (total) (4.8) (.6) () Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Horsepower 5 5 5 Motor Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Maximum Unit Only 50 50 60 0 0 5 0 0 5 Overcurrent With () 0. HP 50 60 70 0 0 5 0 0 5 Protection Power Exhaust Minimum Unit Only 4 46 5 4 6 9 6 8 0 Circuit With () 0. HP 46 49 56 6 7 0 7 9 Ampacity Power Exhaust NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. 0 TON HIGH EFFICIENCY (R-40A) KGA0H4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps.5 8 5 Locked Rotor Amps 09 59 40 Compressor Rated Load Amps.5 8 5 Locked Rotor Amps 09 59 40 Outdoor Fan Motors () Power Exhaust () 0. HP Full Load Amps.4. (total) (4.8) (.6) () Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Motor Maximum Overcurrent Protection Minimum Circuit Ampacity Horsepower 5 5 5 Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Unit Only 50 50 60 0 0 5 0 0 5 With () 0. HP Power Exhaust 50 60 70 0 0 5 0 0 5 Unit Only 4 46 5 4 6 9 6 8 0 With () 0. HP Power Exhaust 46 49 56 6 7 0 7 9 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 8
ELECTRICAL DATA.5 TON STANDARD EFFICIENCY (R-40A) KG50S4 Voltage - 60hz 08/0V - Ph 460V - Ph 575V - Ph Compressor Rated Load Amps 9.6 8. 6.6 Locked Rotor Amps 6 66. 55. Compressor Rated Load Amps.4 0.6 7.7 Outdoor Fan Motors () Power Exhaust () 0. HP Locked Rotor Amps 49 75 54 Full Load Amps.5. (total) (6) () (.4) Full Load Amps.4. Service Outlet 5V GFI (amps) 5 5 0 Indoor lower Horsepower 5 5 5 Motor Full Load Amps 7.5 0.6 6.7.4 4.8 7.6.7.9 6. Maximum Unit Only 80 80 90 5 5 40 5 0 0 Overcurrent With () 0. HP Protection Power Exhaust 80 80 90 5 40 40 0 0 0 Minimum Unit Only 6 65 7 8 0 5 Circuit With () 0. HP Ampacity Power Exhaust 64 67 7 0 4 4 6 NOTE - All units have a minimum Short Circuit Current Rating (SCCR) of 5000 amps. Extremes of operating range are plus and minus 0% of line voltage. HACR type breaker or fuse. Refer to National or Canadian Electrical Code manual to determine wire, fuse and disconnect size requirements. Page 9
KGA/KG PARTS ARRANGEMENT ECONOMIZER (OPTIONAL) DISCONNECT / CIRCUIT REAKER (FACTORY- OR FIELD- INSTALLED OPTION) EVAPORATOR COIL LOWER MOTOR CONDENSER FANS CONDENSER COIL LOWER COMPRESSORS FILTERS (FOUR - 0 X 5 X ) CONDENSATE DRAIN GAS VALVE URNERS COMUSTION AIR INDUCER FIGURE KGA/KG CONTROL OX Y, G, J-VOLT UNITS KGA/KG CONTROL OX M VOLT CE UNITS K K T K65 K0 K K K T K65 K0 S4 K T K5 S76 S77 S4 FIGURE FIGURE Page 0
I-UNIT COMPONENTS All 7.5 through.5 ton (6. through 44 kw) units are configure to order units (CTO). The KGA/KG unit components are shown in figure. All units come standard with removable unit panels. All L, L and L wiring is color-coded; L is red, L is yellow and L is blue. A-Control ox Components KGA/KG control box components are shown in figures and. The control box is located in the upper portion of the compressor compartment. -onnect Switch S48 (Field-Installed for all units) All units may be equipped with an optional disconnect switch S48 or circuit breaker C0. S48 and C0 are toggle switches, which can be used by the service technician to disconnect power to the unit. -Control Transformer T all units All use a single line voltage to 4VAC transformer installed in the control box. The transformer supplies power to control circuits in the unit. The transformer is rated at 70VA and is protected by a.5 amp circuit breaker (C8). The 08/0 (Y) voltage transformers use two 08/0V TRANSFORMER primary voltage taps as LUE YELLOW shown in figure 4, while SECONDARY 460 (G) and 575 (J) voltage transformers 08 VOLTS use a single primary RED voltage tap. 0 VOLTS PRIMARY ORANGE LACK FIGURE 4 -C. A. I. Transformers T 575V units All KGA/KG 575 (J) voltage units use transformer T located in the control box. The transformers have an output rating of 0.5A. T transformer supplies 0 VAC power to the combustion air inducer motor (6). 4-Terminal Strip T All indoor thermostat connections are made at terminal block T located in the control area. For thermostats without occupied and unoccupied modes, a factory-installed jumper across terminals R and OC should be in place. 5-Condenser Fan Capacitors C & C Fan capacitors C and C are used to assist in the start up of condenser fans 4 and 5. Ratings will be on side of capacitor or outdoor fan motor nameplate. 6-Compressor Contactor K & K All compressor contactors are three pole double break contactors with 4VAC coils. In all KGA/KG units, K and K energize compressors and in response to thermostat demand. On CE M-voltage units, contactor is CE approved by manufacturer (Siemens). See figure 5. 7-lower Contactor K CONTACTOR FIGURE 5 lower contactor K, used in all units, is a three poledouble break contactor with a 4VAC coil used to energize the indoor blower motor in response to blower demand. K is energized by a thermostat cooling demand. On M-volt CE units, the contactor is CE approved by manufacturer (Siemens). See figure 5. 8-Condenser Fan Relay K0 Outdoor fan relay K0 is a DPDT relay with a 4VAC coil. K0 energizes condenser fans 4 and 5. 9-Power Exhaust Relay K65 (PED units) Power exhaust relay K65 is a DPDT relay with a 4VAC coil. K65 is used in all KGA/KG units equipped with the optional power exhaust dampers. K65 is energized by the economizer enthalpy control A6, after the economizer dampers reach 50% open (adjustable) When K65 closes, exhaust fan 0 is energized. Page
KGA/KG09,0, 0, 50 PLUMING AND COMPRESSOR CIRCUITS DETAIL OUTDOOR COIL STAGE INDOOR COIL STAGE INDOOR COIL STAGE DRIERS OUTDOOR COIL STAGE COMPRESSOR COMPRESSOR COMPRESSOR COMPRESSOR S8 THERMAL PROTECTOR DISCHARGE LINE SUCTION LINE S5 THERMAL PROTECTOR SUCTION LINE S7 HIGH PRESSURE SWITCH PRESSURE TAP DISCHARGE LINE S4 HIGH PRESSURE SWITCH PRESSURE TAP FIGURE 6 Page
-Cooling Components All units use independent cooling circuits consisting of separate compressors, condenser coils and evaporator coils. See figure 6. Two draw-through-type condenser fans are used in KGA/KG09/50 units. All units are equipped with belt drive blowers which draw air across the evaporator during unit operation. Cooling may be supplemented by a factory or fieldinstalled economizer. The evaporators are slab-type and are stacked. Each evaporator uses a thermostatic expansion valve as the primary refrigerant metering device. Each evaporator is also equipped with enhanced fins and rifled tubing. In all units each compressor is protected by S49 and S50 freezestats and S4 and S7 high pressure switches (on each evaporator). Low ambient switches (S and S84) are available as an option for additional compressor protection. On 50 units, each compressor is protected by a crankcase heater. -Compressors and All KGA/KG09/50 units use two scroll compressors. Compressor capacity may vary from stage to stage. In all cases, the capacity of each compressor is added to reach the total capacity of the unit. See SPECIFICATIONS and ELECTRICAL DATA (table of contents) or compressor nameplate for compressor specifications. WARNING Electrical shock hazard. Compressor must be grounded. Do not operate without protective cover over terminals. onnect power before removing protective cover. harge capacitors before servicing unit. Failure to follow these precautions could cause electrical shock resulting in injury or death. Each compressor is energized by a corresponding compressor contactor. NOTE-Refer to the wiring diagram section for specific unit operation. If Interlink compressor replacement is necessary, call -800-4-LENNOX (-800-45-6669). IMPORTANT Some scroll compressors have an internal vacuum protector that will unload scrolls when suction pressure goes below 0 psig. A hissing sound will be heard when the compressor is running unloaded. Protector will reset when low pressure in system rises above 40 psig. DO NOT REPLACE COMPRESSOR. -Thermal Protectors S5, S8 Some compressors have thermal protectors located on top of the compressor. The protectors open at 48 F + 9 F (0 C + 5 C) and close at 69 F + 8 F (76 C + 0 C). -Freezestats S49 and S50 Each unit is equipped with a low temperature switch (freezestat) located on a return bend of each evaporator coil. S49 (first circuit) and S50 (second circuit) are located on the corresponding evaporator coils. Freezestats are wired in series with compressor contactors. Each freezestat is a SPST N.C. auto-reset switch which opens at 9 F + F (.7 C +.7 C) on a temperature drop and closes at 58 F + 4 F (4.4 C +. C) on a temperature rise. To prevent coil icing, freezestats open during compressor operation to temporarily disable the respective compressor until the coil temperature rises. If the freezestats are tripping frequently due to coil icing, check the airflow/filters, economizer position and unit charge before allowing unit back in operation. Make sure to eliminate conditions which might promote evaporator ice buildup. 4-High Pressure Switches S4 and S7 The high pressure switch is a manual reset SPST N.C. switch which opens on a pressure rise. S4 (first circuit) and S7 (second circuit) are located in the compressor discharge line and are wired in series with the respective compressor contactor coils. When discharge pressure rises to 640 ± 0 psig (44 ± 69 kpa) (indicating a problem in the system), the switch opens and the respective compressor is de-energized (the economizer can continue to operate). 5-Low Ambient Switches S & S84 (optional) The low ambient switch is an auto reset SPST N.O. pressure switch which allows for mechanical cooling operation at low outdoor temperatures. In all models, a switch is located in each liquid line prior to the indoor coil section. In the KGA/KG09/50, S and S84 are wired in parallel with outdoor fan relay K0. When liquid pressure rises to 450 ± 0 psig (0 ± 69 kpa), the switch closes and the condenser fans are energized. When liquid pressure in both refrigerant circuits drops to 40 ± 0 psig (655 ± 69 kpa), the switches open and the condenser fans are de-energized. This intermittent fan operation results in higher evaporating temperature allowing the system to operate without icing the evaporator coil and losing capacity. 6-Crankcase Heaters HR, HR 50S units use insertion-type heaters. Heater HR is installed around compressor and heater HR is installed around compressor. Crankcase heater wattage varies by compressor manufacturer. Page
C-lower Compartment The blower compartment in all KGA/KG09/50S units is located between the evaporator coil and the condenser coil section. The blower assembly is accessed by disconnecting the blower motor.see lower Access in the Operation/ Adjustment section. -lower Wheels All KGA/KG09/50 units have one 5 in. x 5 in. (8 mm x 8 mm) blower wheel. -Indoor lower Motor All units use three phase single speed blower motors. CFM adjustments are made by adjusting the motor pulley (sheave). Motors are equipped with sealed ball bearings. All motor specifications are listed in the SPECIFICATIONS(table of contents) in the front of this manual. Units may be equipped with motors manufactured by various manufacturers, therefore electrical FLA and LRA specifications will vary. See unit rating plate for information specific to your unit. Operation and Adjustments A-Three Scroll Compressor Voltage Phasing Three phase scroll compressors must be phased sequentially to ensure correct compressor and blower rotation and operation. Compressor and blower are wired in phase at the factory. Power wires are color-coded as follows: line -red, line -yellow, line -blue. - Observe suction and discharge pressures and blower rotation on unit start-up. If pressure differential is not observed or blower rotation is not correct: - ion pressure must drop, discharge pressure must rise, and blower rotation must match rotation marking. - onnect all remote electrical power supplies. 4- Reverse any two field-installed wires connected to the line side of K, T or F4. Do not reverse wires at blower contactor or compressors. 5- Make sure the connections are tight. harge and suction pressures should operate at their normal start up ranges. Supply Air Inverter Units - Units are equipped with a phase monitor located in the control compartment. The phase monitor will detect the phasing of incoming power. If the incoming power is out of phase or if any of the three phases are lost, the indicating LED on the phase monitor will turn red and the unit will not start. In normal operation with correct incoming power phasing, the LED will be green. -lower Operation Initiate blower demand at thermostat according to instructions provided with thermostat. Unit will cycle on thermostat demand. The following steps apply to applications using a typical electro-mechanical thermostat. - lower operation is manually set at the thermostat subbase fan switch. With fan switch in ON position, blowers will operate continuously. - With fan switch in AUTO position, the blowers will cycle with demand. lowers and entire unit will be off when system switch is in OFF position. C-lower Access The blower assembly is secured to a sliding frame which allows the blower motor to be pulled out of the unit. See figure 7. - Loosen the reusable wire tie which secures the blower wiring to the blower motor mounting plate. - Remove and retain screws on either side of sliding frame. Pull frame toward outside of unit. - Slide frame back into original position when finished servicing. Reattach the blower wiring in the previous location on the blower motor base using the wire tie. 4- Replace retained screws on either side of the sliding frame. Page 4
TO INCREASE ELT TENSION STANDARD LOWER ASSEMLY - Loosen four bolts securing motor mounting base to frame. - Turn adjusting bolt to the right, or clockwise, to move the motor away from the blower housing. IMPORTANT - Gap between end of frame and motor mounting base should be equal at both ends, i.e. parallel along gap. - Tighten four bolts securing motor mounting base to frame. 4- Relieve tension on two adjusting bolts. MOTOR MOUNTING ASE ELT ADJUSTING OLTS - TURN CLOCKWISE TO TIGHTEN ELT LOWER HOUSING SIDE VIEW MOTOR ALLEN SCREW PULLEY GAP ETWEEN EDGES SHOULD E PARALLEL ON OTH ENDS EFORE TIGHTENING MOTOR MOUNTING ASE IN PLACE MOTOR LOWER FRAME REMOVE TWO SCREWS TO COMPLETELY SLIDE LOWER OUT OF UNIT D-Determining Unit CFM IMPORTANT - Units equipped with an inverter are factoryset to run the blower at full speed when there is a blower (G) demand without a heating or cooling demand. Use the following procedure to adjust motor pulley to deliver the full load cooling or heating CFM. See Inverter Start-Up section to set blower CFM for all modes once the motor pulley is set. - The following measurements must be made with a dry indoor coil. Run blower without a cooling demand. Measure the indoor blower shaft RPM. Air filters must be in place when measurements are taken. - With all access panels in place, measure static pressure external to unit (from supply to return). lower performance data is based on static pressure readings taken in locations shown in figure 8. Note - Static pressure readings can vary if not taken where shown. - Referring to page, 4, or 5, use static pressure and RPM readings to determine unit CFM. Use pages 6 and 7 when installing units with any of the optional accessories listed. LOOSEN EFORE ADJUSTING ELT TENSION (TWO EACH SIDE) REMOVE TWO SCREWS ON EACH SIDE TO SLIDE FRAME PARTIALLY OUT OF UNIT FOR SERVICE ACCESS FIGURE 7 4- The blower RPM can be adjusted at the motor pulley. Loosen Allen screw and turn adjustable pulley clockwise to increase CFM. Turn counterclockwise to decrease CFM. See figure 7. Do not exceed minimum and maximum number of pulley turns as shown in table. TALE MINIMUM AND MAXIMUM PULLEY ADJUSTMENT elt Minimum Turns Open Maximum Turns Open A Section 0 5 Section * 6 *No minimum number of turns open when belt is used on pulleys 6 O.D. or larger. E-lower elt Adjustment Maximum life and wear can be obtained from belts only if proper pulley alignment and belt tension are maintained. Tension new belts after a 4-48 hour period of operation. This will allow belt to stretch and seat in the pulley grooves. Make sure blower and motor pulleys are aligned as shown in figure 9. - Loosen four bolts securing motor base to mounting frame. See figure 7. Page 5