HISTORICAL OF SAMPLE RECEIVED BVLCIE CHINA RECORDED N DETAIL OF THE SAMPLE SPECIAL REMARKS SZ130513/006 Original sample None SZ130328/002 Original sample None SZ130328/001 Original sample None EAMINED SECTIONS The full tests have been required on a range of lighting: models CM-PL14W-24018, CM-PL54W- 600600, CM-PL72W-6001200 and their related LED drivers. The models covered in this report are class III recessed luminaire used with LED drivers which are not approved. Because these lighting are similar constructions except differences as listed in table 1 below, we performed the tests as below for luminaire part. All sections for the model CM-PL72W-6001200. Sections 0-8, 11, 12.4 for the model CM-PL14W-24018. Sections 0-8, 11 for the model CM-PL54W-600600. Table 1 Model number LED controlgear LED Quantity & Spec. Shape & Dimension CM-PL14W-24018 CM-PS-14W 120 x 0.1W/SMD3014 Round/240x18 CM-PL54W-600600 CM-PS-54W 480 x 0.1W/SMD3014 Rectangle/600x600 CM-PL72W-6001200 CM-PS-72W 640 x 0.1W/SMD3014 Rectangle/600x1200 For LED controlgears, the models CM-PS-54W and CM-PS-72W have same PCB layout, circuit diagram and outlook except the controlgear CM-PS-54W doesn t use 30mΩ resistor at the place of D10A and RS1A on PCB, we performed the tests as below for LED controlgear. All sections for the model CM-PS-72W and CM-PS-14W. Construction checking for the model CM-PS-54W. These lighting equipments are also evaluated according to the IEC 62471:2006, and it is classified as exempt group for LED, please refer to the test report LEY-13MA157LTZP dated on June 7, 2013. All samples listed (models CM-PL14W-24018, CM-PL54W-600600, CM-PL72W-6001200) are covered by the conclusion on page 1. Honghualing Industrial Park, Liu ian Road, ili Page 2 of 40
Raing label of luminaire: stuck on the back of light COPY OF RATING PLATE: None Raing label of controlgear: stuck on the back of light None Only markings in English Language present on the sample tested were checked and validated during this examination. The text required by the standard should be translated into the official language of the country where the will be sold. Honghualing Industrial Park, Liu ian Road, ili Page 3 of 40
PICTURE OF THE SAMPLE TESTED: Model: CM-PL14W-24018 Honghualing Industrial Park, Liu ian Road, ili Page 4 of 40
PICTURE OF THE SAMPLE TESTED(CONTINUED): Model: CM-PL14W (for use with CM-PL14W-240 18) Honghualing Industrial Park, Liu ian Road, ili Page 5 of 40
PICTURE OF THE SAMPLE TESTED(CONTINUED): Model: CM-PS-14W (for use with CM-PL14W-240 18) Honghualing Industrial Park, Liu ian Road, ili Page 6 of 40
PICTURE OF THE SAMPLE TESTED(CONTINUED): Model: CM-PL54-600600 Honghualing Industrial Park, Liu ian Road, ili Page 7 of 40
PICTURE OF THE SAMPLE TESTED(CONTINUED): Model: CM-PL72W-6001200 Honghualing Industrial Park, Liu ian Road, ili Page 8 of 40
PICTURE OF THE SAMPLE TESTED(CONTINUED): Model: CM-PS-72W (for use with CM-PL72W-6001200) Model: CM-PS-54W (for use with CM-PL54-600600) Honghualing Industrial Park, Liu ian Road, ili Page 9 of 40
PICTURE OF THE SAMPLE TESTED(CONTINUED): Model: CM-PS-72W (for use with CM-PL72W-6001200) Model: CM-PS-54W (for use with CM-PL54-600600) Note: (1) the controlgear CM-PS-54W doesn t use 30mΩ resistor at the place of D10A and RS1A on PCB; (2) The input cord length of luminaire is shorter than 80mm. Honghualing Industrial Park, Liu ian Road, ili Page 10 of 40
DESCRIPTION Trademark: SuperLED Electronic Co., Limited Type of : Recessed luminaires Type / model: CM-PL14W-24018, CM-PL54W-600600, CM- PL72W-6001200 Color of enclosure: See pages 9-13 40V for model CM-PL14W-24018; Rated Voltage (V): 42V for models CM-PL54W-600600 and CM- PL72W-6001200. Nature of supply: DC 14W for model CM-PL14W-24018; Rated power (W) 54W for model CM-PL54W-600600; 72w for model CM-PL72W-6001200. Class of protection against electrical shock: Class III Degree of protection against moisture: IP20 CE marking: NA F marking: NA Type of switch: NA Type of fixation (, Y, M, Z): Y Marking on knobs: NA Supply connection: Connecting tails Other information about : Light source: LED Accessory provided with the luminaire: Instruction sheet Possible test case verdicts: - Test object does meet the requirement P (Pass) - Test case does not apply to the test object NA (Not applicable) - Test object does not meet the requirement F (Fail) - Test object does not demand ND (Not demanded) General remarks: "(See remark #)" refers to a remark appended to the report. Throughout this report a comma is used as the decimal separator. Honghualing Industrial Park, Liu ian Road, ili Page 11 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict 0 COMPONENTS OF LUMINAIRES P Components comply with the requirements of the relevant standards (see page 21-25/40) P 2 CLASSIFICATION P. Compliance of the classification P 3 MARKING P. Marking on the luminaires P. Other requirements P 4 CONSTRUCTION P 4.2 - Replaceable components P 4.3 - Wire ways P 4.4 - Lamp holders NA 4.5 - Starter holders NA 4.6 - Terminal blocks NA 4.7 - Terminals and supply connections P 4.8 - Switch NA 4.9 - Insulating linings and sleeves NA 4.10 - Double and reinforced insulation NA 4.11 - Electrical connections and current-carrying parts P 4.12 -Screws and connections (mechanical), glands P 4.13 - Mechanical strength P 4.14 - Suspensions and adjusting devices (1) P 4.15 - Flammable materials P 4.16 - Luminaires for mounting on normally flammable surfaces P 4.17 - Drain holes NA 4.18 - Resistance to corrosion NA 4.19 - Ignitors NA 4.20 - Rough service luminaires NA - Vibrations requirements NA 4.21 - Protective shield (tungsten halogen lamps) NA 4.22 - Attachments to lamps NA 4.23 - Semi- luminaires NA 4.24 - UV radiation NA 4.25 - Mechanical hazard P 4.26 - Short-circuit protection NA 1. Frequently adjusted [ ] occasionally adjusted [ ] adjusted during installation only [ ] Honghualing Industrial Park, Liu ian Road, ili Page 12 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict 11 CREEPAGE DISTANCES AND CLEARANCES P Minimum distances (mm) P Basic insulation 0.2-1.2 P Supplementary insulation - NA Reinforced insulation - NA 7 PROVISION FOR EARTHING NA. No provision for class II and class III s NA. Earthing connections of low resistance NA - Test: >10A, <12V Result: R<0,5Ω NA. Other requirements NA 14 SCREW TERMINALS NA. Compliance with the requirements of relevant standards NA. Compliance with the requirements of this section NA 15 SCREWLESS TERMINALS AND ELECTRICAL CONNECTIONS NA. Compliance with the requirements of relevant standards NA. Compliance with the requirements of this section NA 5 ETERNAL AND INTERNAL WIRING P 5.2. Supply connection and other external wiring P 5.3. Internal wiring P 8 PROTECTION AGAINST ELECTRIC SHOCK P. Live parts not accessible P. Other requirements P 12 ENDURANCE TEST AND THERMAL TEST P 12.3 - Endurance test P. ta = 50 C [] - ta = 25 C [ ] P. U = 1,05 U to Pn [ ] - P = 1,05 Pn [ ] - U = 1,1 Un [] P. 10 cycles [] - 7 cycles [ ] P. Results P 12.4 - Thermal test (normal operation) P. ta = 40 C P. P = 1,05 Pn [ ] - U = 1,0 Un puis 1,06 Un [ ] - U = 1,06 Un [] P. Results (below) P Honghualing Industrial Park, Liu ian Road, ili Page 13 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict PARTS NA Maximum temperature specified ( C+5 C) Maximum temperature measured ( C) CM-PL14W- CM-PL72W- 24018 6001200. Lamps caps. Ballast winding: - tw 130 - tw. Transformer winding: - Class H - Class. Case: - Of capacitor - Of starting device - Of ballast - Of convertor - Of LED controlgear 80 70 75. Insulation of wiring not stressed (mechanical stress): - PVC (external) x - PVC (internal) 90 51 56 - PVC with sleeve - Silicone [ ] -glassfibre [ ] -PTFE. Insulation of wiring stressed (mechanical stress): - PVC - Silicone [ ] -glassfibre [ ] -. Heat-resisting sleeves. Contacts of ceramic lampholders. Insulating material - Of lampholder - Of starter holder. Switches. Insulating materials retaining current-carrying parts in position (connector plastic) (1) For reference 54 58. Insulating materials providing protection against electric shock. Mounting surface 90 53 57. Objects lighted (d = 0.2m) 90 51 54. Test recess. Track Honghualing Industrial Park, Liu ian Road, ili Page 14 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict PARTS NA. Mains socket-outlet-mounted-luminaire and plug-ballast-transformer: x - Case intended to be gripped by hand x - Plug-socket interface x - Other parts x. Wood x. Other requirements x Maximum temperature specified ( C+5 C) Maximum temperature measured ( C) (1) No limit is specified, but these materials must satisfy the tests of section 13 For LED controlgear with model CM-PS-14W. PARTS NA Maximum temperature Maximum temperature specified ( C+5 C) measured ( C) Primary winding 120 90 Secondary winding 120 82 Core of transfomer 120 86 Bobbin 150 84 2 capacitor(c1) 105 77 E-capacitor(C10) 105 77 E-capacitor(C11) 105 69 VR1 85 71 Line filter(lf1) 120 70 Inductance(L3) 120 73 Y1 capacitor(cy1) 125 65 PCB 120 64 NTC(NTC1) Ref 46 Enclosure(inside) Ref 84 Input wire 90 81 Output wire 90 64 Tc point 80 70 For LED controlgear with model CM-PS-72W. PARTS NA Maximum temperature Maximum temperature specified ( C+5 C) measured ( C) Primary winding 120 99 Secondary winding 120 98 Core of transfomer 120 98 Bobbin 150 90 2 capacitor(c1) 105 71 E-capacitor(C21) 105 86 E-capacitor(C26) 105 82 E-capacitor(C27) 105 84 MOV1 85 69 Line filter(lf2) 120 82 Inductance(L2) 120 82 Y1 capacitor(cy1) 125 81 Honghualing Industrial Park, Liu ian Road, ili Page 15 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict Y1 capacitor(cy3) 125 67 PCB(under BD1) 120 85 PCB(under transformer) 120 91 PCB(under Q2) 120 81 Optocoupler(U4) 110 70 NTC(NTC1) Ref Ref Input wire 90 64 Output wire 90 58 Tc point 80 75 12.5 - Thermal test (abnormal operation) P. ta = 40 C P. P = 1,05 Pn [ ] - U = 1,1 Un [x] -U = 1,06 Un [ ] P. Abnormal circuit condition applied: NA - Short-circuit of starter contacts [ ] NA - Overturning [ ] NA - Unfavorable adjusting to the lighted surface [ ] NA - Secondary circuit short-circuited [x] P - Other condition [ ] : NA. Results (below) P (**) The samples were stable to 15 PARTS NA Maximum temperature specified ( C+5 C) Honghualing Industrial Park, Liu ian Road, ili Page 16 of 40 Maximum temperature measured ( C) CM-PL14W- 24018 CM-PL72W- 6001200. Ballast winding: - tw 130 - tw. Transformer winding: - Class H - Class. Case of capacitor. Case of LED controlgear 90 48 57. Mounting surface [] -Lighted surface [ 130 59 65. Test recess. Track. Mains socket-outlet-mounted-luminaires and plug-ballast case parts intended to be gripped by hand Transformer case parts intended to be gripped by hand For LED controlgear PARTS NA Maximum temperature rise measured Maximum temperature (K) rise specified (K) CM-PS-14W CM-PS-72W Primary winding 150-(40-25)=135 43 51 Secondary winding 150-(40-25)=135 36 49
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict 12.6 - Thermal test (failed lamp control gear conditions) NA. ta = 25 C NA 12.6.1 - Ballast/transformer without thermal cut-outs: NA. Abnormal condition applied: NA - Lamp not start [ ] NA - Other condition [ ] : NA. Results (below): NA - T of mounting surface 180 C for T winding = 350 C NA Supply voltage Temperatures ( C) Of ballast winding Of mounting surface 0,9 Un - - 1,0 Un - - 1,1 Un - - 12.6.2 - Ballast/transformer with thermal cut-outs: NA. Abnormal condition applied: NA - Lamp not start [ ] NA - Other condition [ ] : NA. Results: NA - T mounting surface 135 C (110 C) NA 12.7 Thermal test (fault conditions in lamp controlgear or electronic devices in plastic NA luminaires) 9 RESISTANCE TO DUST, SOLID OBJECTS AND MOISTURE P 9.2 - Tests for ingress, P. Of solid objects IP3 [ ] - 4 [ ] IP2 P. Of dust IP5 [ ] - 6 [ ] NA. Of moisture IP1 [ ] - 3 [ ] - 4 [ ] - 5[ ] - IP0 6[ ] - 7 [ ] - 8 [ ] NA 9.3 - Humidity test 48hours, 93%, 25 C P Honghualing Industrial Park, Liu ian Road, ili Page 17 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict 10 INSULATION RESISTANCE AND ELECTRIC P STRENGTH 10.2 Insulation Insulation resistance Electric strength Basic 1 MΩ [] 2 MΩ[ ] 500 V [] 1460 V [ ] Reinforced 4 MΩ [ ] 3670 V [ ] Supplementary 2 MΩ 2210 V [ ]. Results P - Parts stressed by the pulse voltage NA 10.3 - Leakage current P 13 RESISTANCE TO HEAT, FIRE AND TRACKING P 13.2 - Resistance to heat P. Ball pressure test Approved component and tested 125 on connector plastic and LED PCB, 75 on LED translucent cover P 13.3 - Resistance to flame and ignition P. Needle-flame test Approved component and tested on connector plastic P. Glow-wire test 650 C Approved component and tested on connector plastic and LED translucent cover P 13.4 - Resistance to tracking NA REQUIREMENTS STANDARD IEC 60598-1 & IEC 60598-2-2 P Honghualing Industrial Park, Liu ian Road, ili Page 18 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict ADDITIONAL TEST FOR IEC 61347-2-13/ IEC 61347-1 SECTIONS TITLE REMARK NOTE PASS FAIL N.A N.D 4(4) General requirements 5(5) General notes on tests 6(6) Classification 7(7) Marking 8(10) Protection against accidental contact with live parts 9(8) Terminals 10(9) Provisions for protective earthing 11(11) Moisture resistance and insulation 12(12) Electric strength 13(13) Thermal endurance test for windings of ballasts 14(14) Fault conditions 15(-) Transformer heating 16(-) Abnormal conditions 17(15) Construction 18(16) Creepage distances and clearances 19(17) Screws, current-carrying parts and connections 20(18) Resistance to heat, fire and tracking 21(19) Resistance to corrosion Annex A Annex B Annex C Test to establish whether a conductive part is a live part which may cause an electric shock Particular requirements for thermally protected lamp controlgear Particular requirements for electronic lamp controlgear with means of protection against overheating Honghualing Industrial Park, Liu ian Road, ili Page 19 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict Annex D Annex E Requirements for carrying out the heating tests of thermally protected lamp controlgear Use of constant S other than 4 500 in tw tests Annex F Draught-proof enclosure Annex G Explanation of the derivation of the values of pulse voltages Annex H Tests Particular additional requirements for independent SELV d.c. or Annex I a.c. supplied electronic controlgear for LED modules N.A: Not applicable N.D: Not demanded The numerals between brackets represent the clauses from the stanrdard IEC 612347-1 ADDITIONAL TEST FOR IEC 62031 SECTIONS TITLE REMARK NOTE PASS FAIL N.A N.D 4 General requirements 5 General test requirements 6 Classification 7 Marking 8 Terminals 9 Provisions for protective earthing 10 Protection against accidental contact with live parts 11 Moisture resistance and insulation 12 Electric strength 13 Fault conditions 15 Construction 16 Creepage distances and clearances 17 Screws, current-carrying parts and connections Honghualing Industrial Park, Liu ian Road, ili Page 20 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict 18 Resistance to heat, fire and tracking 19 Resistance to corrosion Annex A Tests N.A: Not applicable N.D: Not demanded Component list-luminaire part Object/part No. LED controlgear (Model: CM- PL14W- 28014) LED controlgear (Model: CM- PL54W- 600600) LED controlgear (Model: CM- PL72W- 6001200) LED Supply cord LED PCB SELV Connector Manufacturer/trade mark SuperLED Electronic Co.,Limited SuperLED Electronic Co.,Limited SuperLED Electronic Co.,Limited Guangzhou Hongli Opto-Electronic Co., Ltd. MAINLAND ELECTRIC WIRE & CABLE CO., LTD. SUZHOU HENG ER TAI ELECTRONIC TECHNOLOGY CO LTD JAPAN SOLDERLESS TERMINAL MFG CO LTD Type/model CM-PS-14W CM-PS-54W CM-PS-72W SMD3014 Technical data input:100-240~, 50/60Hz, 0.15A output: 38-46VDC, 300mA, MA14W, ta: 40,tc: 80 input:100-240~, 50/60Hz, 0.5A output: 40-43VDC, 1250mA, MA54W, ta: 40,tc: 80 input :100-240~, 50/60Hz, 0.65A output : 40-48VDC, 1500mA, MA72W, ta: 40,tc: 80 6000-6500K 3.01.4x0.8mm Mark(s) of conformity H03VV-F 20.75mm 2 VDE HAF-2 Series EL V-0, 90 E350374 PP E60389 1 2 3 R Honghualing Industrial Park, Liu ian Road, ili Page 21 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict Component list-lamp controlgear part (Model: CM-PS-54W & CM-PS-72W) Object/part No. Fuse (F1) Manufacturer/trade mark Walter Electronic Co., Ltd. Type/model NTC(NTC1) JOYIN CO LTD 08S080Y Varistor (MOV1) Capacitor (C1) Y capacitor (CY1, CY2 & CY3) Line filter (LF1) -Winding Rectifying unit(bd1) Opto-coupler Transformer (T1) -Bobbin Material Shantou High-New Technology Dev. Zone Songtian Enterprise Co., Ltd. SHUN DE DAHUA ELECTRIC CO LTD Shantou High-New Technology Dev. Zone Songtian Enterprise Co., Ltd. HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD SEP ELECTRONIC CORP EVERLIGHT ELECTRONICS CO LTD SuperLED Electronic Co.,Limited Chang Chun Plastics Co., Ltd. Technical data Mark(s) of conformity 2010 series 3.15A, AC250V VDE STE-10D561K HD-Series CD-Series U-101 2UEW KBL410 EL817 CM-T1-1 T375J 240V, 2A, E171531 AC50-625V, 25A, 40/085/21 2, 0.33uF, AC275V, 40/105/21 AC400V, 2200pF, 25/125/21 Ø0.5mm,12T Class B 130 E253843 4A, 1000V E142814 AC5000V Dti. = 0.5mm, Int.dcr:6.0mm, Ext.dcr:7.7mm, 110 N1: Ø0.5mm 1x18T, N2:Ø0.2mm 3x6T, N3:Ø0.05mm 8x0.9T, N4:Ø0.35mm 4x11T, N5:Ø0.05mm 8x0.9T, N6:Ø0.5mm 1x12T Class B V-0, 150, E59481 VDE VDE VDE VDE 1 2 3 R Honghualing Industrial Park, Liu ian Road, ili Page 22 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict Object/part No. -Primary magnetic wire -Secondary triple insulated wire -insulation tape -TFL tubing on winding Input wire Output wire SELV Connector PCB Insulation sheet Manufacturer/trade mark HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD Dah Jin Technology Co., Ltd. JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO LTD ZEUS INDUSTRIAL PRODUCTS INC MAINLAND ELECTRIC WIRE & CABLE CO., LTD. MAINLAND ELECTRIC WIRE & CABLE CO., LTD. JAPAN SOLDERLESS TERMINAL MFG CO LTD JERICO MULTILAYER PCB CO LTD JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO LTD Type/model 2UEW TLW-B CT TFE-TW-300 Technical data Polyurethane, 130 E253843 130 Reinforced insulation 130 EE165111 300V, 200 E64007 Mark(s) of conformity VDE H03VV-F 20.75mm 2 VDE H03VV-F 20.75mm 2 VDE Series EL JR-02 CT-280 Type L E60389 1.6mm, 130, V-0 E349456 130, E165111 1 2 3 R Honghualing Industrial Park, Liu ian Road, ili Page 23 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict Component list-lamp controlgear part (Model: CM-PS-14W) Object/part No. Fuse (F1) Manufacturer/trade mark Walter Electronic Co., Ltd. Type/model NTC(NTC1) JOYIN CO LTD 10S080Y Varistor (VR1) Capacitor (C1) Y capacitor (CY1) Line filter (LF1) -Winding PCB Transformer (T1) -Bobbin Material Primary magnetic wire -Secondary magnetic wire -insulation tape Shantou High-New Technology Dev. Zone Songtian Enterprise Co., Ltd. SHUN DE DAHUA ELECTRIC CO LTD Shantou High-New Technology Dev. Zone Songtian Enterprise Co., Ltd. HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD JERICO MULTILAYER PCB CO LTD SuperLED Electronic Co.,Limited Chang Chun Plastics Co., Ltd. HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD HUIZHOU CITY DENGGAODA ELECTROTECH CO LTD JINGJIANG YAHUA PRESSURE SENSITIVE GLUE CO LTD Technical data Mark(s) of conformity 2010 series 2.0A, AC250V VDE STE-07D471K HD-Series CD-Series U-102 2UEW JR-02 CM-T1-1 T375J 2UEW 2UEW CT 240V, 3A E171531 AC50-420V. 10A 40/085/21 2, 0.1Uf, AC275V, 40/105/21 AC400V, 4700Pf, 25/125/21 Ø0.18mm, 160T Class B 130 E253843 1.6mm, 130, V-0 E349456 Class B V-0, 150, E59481 Polyurethane, 130 E253843 Polyurethane, 130 E253843 130 EE165111 VDE VDE VDE 1 2 3 R Honghualing Industrial Park, Liu ian Road, ili Page 24 of 40
IEC 60598-1 & IEC 60598-2-2 Section Requirement Test Result Value Remark Verdict Object/part No. -TFL tubing on winding Input wire Output wire SELV Connector Manufacturer/trade mark ZEUS INDUSTRIAL PRODUCTS INC MAINLAND ELECTRIC WIRE & CABLE CO., LTD. MAINLAND ELECTRIC WIRE & CABLE CO., LTD. JAPAN SOLDERLESS TERMINAL MFG CO LTD Type/model TFE-TW-300 Technical data 300V, 200 E64007 Mark(s) of conformity H03VV-F 20.75mm 2 VDE H03VV-F 20.75mm 2 VDE Series EL Type L E60389 1 2 3 R (1) This component bears the stamp of a European conformity mark or has been granted a certificate of conformity. (2) Applicable specific rules do not exist for this component; consequently, it has been tested according to the requirements of appropriate clauses of applied documents and is satisfactory. (3) This component has been tested according to the requirements of appropriate clauses of applied documents and is satisfactory. Honghualing Industrial Park, Liu ian Road, ili Page 25 of 40
Annex 1: (instruction sheet) Model: CM-PL14W-24018 Honghualing Industrial Park, Liu ian Road, ili Page 26 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 27 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 28 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 29 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 30 of 40
Model: CM-PL54W-600600 Honghualing Industrial Park, Liu ian Road, ili Page 31 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 32 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 33 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 34 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 35 of 40
Model: CM-PL72W-6001200 Honghualing Industrial Park, Liu ian Road, ili Page 36 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 37 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 38 of 40
Honghualing Industrial Park, Liu ian Road, ili Page 39 of 40
Only markings in English and Arabic Language present on the sample tested were checked and validated during this examination. The text required by the standard should be translated into the official language of the country where the will be sold. Honghualing Industrial Park, Liu ian Road, ili Page 40 of 40