BARRACUDA 00ZW PORTABLE WALKING FOOT SEWING MACHINE INSTRUCTION MANUAL
THE BARRACUDA 00ZW PORTABLE WALKING FOOT SEWING MACHINE INSTRUCTION MANUAL MATERIAL IS OWNED BY RELIABLE AND MAY NOT BE REPRODUCED IN WHOLE OR IN PART WITHOUT EXPRESS WRITTEN PERMISSION FROM RELIABLE CORPORATION COPYRIGHT 06 RELIABLE CORPORATION
PREFACE The Reliable Barracuda 00ZW zig-zag and straight stitch portable walking-foot machine is remarkably versatile. Designed for boat owners, hobbyists, and small businesses, the Barracuda is ideal for medium-to-heavy-weight sewing jobs. SMALL SIZE, BIG PERFORMANCE With a stitch quality comparable to an industrial machine, there s no job too big for the Barracuda. With top and bottom feeding, it produces a perfect, even stitch, even when sewing over challenging materials.
TABLE OF CONTENTS Machine speed... Oiling... Needle... Thread... Bobbin winding... 3 Threading the machine and needle... Prepare for sewing... 5 To start sewing... 5 To regulate the length of stitch... 6 Reverse sewing... 6 Adjusting the tension... 7 To remove the hook and clean the race... 8 Clutch washer/screw-assembly instructions... 9 Constructional drawing... 0 External group... External group parts list... Sewing transmission group... 3 Sewing transmission group parts list... Shuttle transmission group... 5 Shuttle transmission group parts list... 6 Feed transmission group... 7 Feed transmission group parts list... 8 Driving & reversing mechanism group... 9 Driving & reversing mechanism group parts list... 0 Electric power & dynamic transmission group... Electric power & dynamic transmission group parts list... ZigZag mechanism group... 3 ZigZag mechanism group parts list... To regulate zigzag width and needle position... Base plate & working plate... 5 Base plate & working plate parts list... 6 Cuda crank installation... 7 Optional Cuda case... 9
SPEED OF MACHINE The maximum speed recommended for this machine is 900 RPM or stitches per minute. Use regular house-hold circuit 5 Volts, 60 HZ. The machine is equipped with a one tenth (/0) HP motor with reduction pulley to provide good power at the recommended speed. This sewing machine can be mounted on a commercial stand. To do so, requires a special cut-out table top, a one inch ( ) diameter pulley, a special Balance Wheel Item No., and a maximum 75 RPM motor. OILING Before operating, oil all metal to metal working parts, and at the places indicated on diagrams below. Use only genuine sewing machine oil. Operate the machine briefly on scrap material after oiling to prevent soiling the work. Frequent oiling is recommended. 0
NEEDLE Use 35x7 needles size 0 to 3. Use size for most medium to heavy sewing. Install needle as illustrated. THREAD To obtain the best results with your sewing machine, we recommend size 69 Bonded Nylon Thread. GROOVE 0
WINDING THE BOBBIN 5 3 03
THREADING THE MACHINE AND NEEDLE 5 6 3 6 5 7 8 0
PREPARE FOR SEWING Thread the machine. Then pick up the bobbin thread as follows:. While holding the loose end of the needle thread in your left hand, turn the balance wheel toward you by hand until the needle moves down and up again to its highest point.. Pull the needle thread gently, and the bobbin thread will come up with it in the form of a loop through the needle hole. 3. With your finger, pull this loop until the end of the thread appears. If the bobbin thread does not rise, check to see if al least 5 or 6 inches of bobbin thread is hanging loosely from the bobbin case. TO START SEWING. Place the material to be sewn under the presser feet and lower them onto the material.. Hold the upper or needle thread (threaded through the eye of the needle) with the fingers of the left hand. Turn (he balance wheel toward you with your right hand until the outside presser foot reaches its most backward position. 3. Now operate the foot control to start sewing. The above procedure is necessary so the motor will start the machine to sewing. Do not help the feeding of the machine by hand, as this may bend or break the needle. Also, damage to the hook can occur. The machine may run a little slow when it s new. However, it will begin to free up and run smoothly with continued use. During operation, the balance wheel of the machine always turns toward the operator. To avoid tangled thread and jamming of the sewing hook, do not turn the balance wheel backward (away from the operator). WARNING: Never operate the machine without material under the presser feet. Your machine will probably lock and cannot be operated until the thread is cleaned out of the hook race. 05
TO REGULATE THE LENGTH OF STITCH Most sewing will be done with the maximum stitch length. However, the length of the stitch can be adjusted as follows:. Loosen the thumb nut on the stitch length lever.. Raise the stitch length (feed regulator) lever until the desired stitch length is obtained. 3. Tighten the thumb nut. 6 5 REVERSE SEWING To sew in reverse:. Lower the feed regulator (stitch length) lever all the way to the bottom of the slot in the stitch length plate.. Hold the lever there until reverse sewing is completed. 3. Then return the lever the forward position. 3 0 FORWARD FEED REVERSE FEED 06
ADJUSTING THE NEEDLE THREAD TENSION ADJUSTING THE bobbin TENSION 07
TO REMOVE THE HOOK AND CLEAN THE RACE DO NOT FORCE ANY OF THESE OPERATIONS. Turn the balance wheel by hand until the needle is at its highest point.. Remove the bobbin and bobbin case. 3. Turn knob (A) one half turn toward you.. Turn knob (B) one half turn away from you. 5. Remove retaining ring (C) and hook (D) by grasping the axle of the hook. 6. Remove accumulated lint and thread from the retaining ring, hook, and race body. 7. Replace hook (D) in race body with the axle facing out, forming a perfect circle with the driver (E). 8. Replace retaining ring (C). polished side out, so that both pins are under knobs (A) and (B). 9. Lock the retaining ring knobs (A) and (B). 0. Replace bobbin and bobbin case, and resume sewing. BOBBIN E D B A AXLE C BOBBIN CASE 08
clutch washer/screw-assembly instructions. Remove clutch stop screw.. Remove hand clutch screw. 3. Notice position of prongs on clutch washer in slot of balance wheel bushing.. Remove clutch washer and make / turn and replace. 5. Screw in hand clutch screw very light 6. Screw in stop screw. 7. Back off on hand clutch screw. 8. Run motor and check to see if balance wheel turns freely without running the machine. 9. Tighten hand clutch screw and the machine should run properly. BALANCE WHEEL CLUTCH WASHER CLUTCH STOP SCREW HAND CLUTCH SCREW SLOT IN BUSHING PRONGS ON CLUTCH WASHER POINT OUT. WILL NOT WORK IF POINTED IN. CLUTCH WASHER 09
CONSTRUCTIONAL 0
GROUP CONSTRUCTION EXTERNAL GROUP 3 9 6 6 6 5 8 7 6 7 7 5 3 7 3 0 7 5 6 6 8-9 9 9 8 8 0 30 3 3
GROUP KEY NO. PART NO. PART NAME Q TY KEY NO. PART NO. PART NAME Q TY W07 TOP PLATE 7 B00 BOBBIN WINDER SET SCREW B07 TOP PLATE SET SCREW 8 W03 NEEDLE PLATE 3 EO66 BOBBIN WINDER STOPPER 9 A05 NEEDLE PLATE SET SCREW E066- BOBBIN WINDER STOPPER SET SCREW 0 A08-B SHUTTLE RACE SLIDE 5 W07- SMALL PLATE COVER W09 THREE HOLE THREAD GUIDE 6 A09 SMALL PLATE COVER SET SCREW BOBBIN WINDER ASSEMBLY SET SCREW W8- DIAL TENSION ASSEMBLY 7 E070- BOBBIN WINDER TENSION ASSEMBLY SET NUT 3 W030 BOBBIN WINDER 8 E070 BOBBIN WINDER TENSION ASSEMBLY W05 CRANK ROO BEARING SET BASE 9 W07- SPOOL PIN 5 W05- CRANK ROD BEARING SET BASE SET SCREW 0 WOO ARM BODY 6 E07 TOP PLATE SET SCREW WOO BED 7 A7 BOBBIN WINDER RUBBER RING D097 NEEDLE BAR SUPPORT SET SCREW THREE HOLE THREAD GUIDE SET SCREW 8 9 W8-3 W8- THREAD TAKE-UP/CHECK-SPRING TENSION RELEASE PIN 3 W08 FACE PLATE 30 A09 SHUTTLE RACE SLIDE SPRING C097 FACE PLATE SET SCREW 3 AO5O SHUTTLE RACE SLIDE SPRING SET SCREW 5 W5 STITCH LENGTH PLATE 8- W03- ZIG ZAG NEEDLE PLATE 6 A075 STITCH LENGTH PLATE SET SCREW
GROUP SEWING TRANSMISSION GROUP 7 0 8 9 8 38 6 6 5 5 3 9 6 7 7 0 3 3 5 37 33 6 3 3 30 35 8-3 9 7 8 3
GROUP KEY NO. PART NO. PART NAME Q TY KEY NO. PART NO. PART NAME Q TY E053 ARM SHAFT A0 NEEDLE BAR CONNECTING JOINT SET SCREW B007 FEED CAM W05 ZIGZAG CONNECTING ROD 3 B05 ARM SHAFT BUSHING 3 B099 NEEDLE BAR CONNECTING JOINT PIN A0 THREAD TAKE-UP ASSEMBLY SET SCREW ARM SHAFT BUSHING SET SCREW TENSION RELEASE LEVER DRAG LINK PIN SET SCREW 5 WO66 WO67 NEEDLE BAR NEEDLE THREAD GUIDE 5 B08 THREAD TAKE-UP LEVER CAM 6 W008 NEEDLE 6 A09 THREAD TAKE-UP ASSEMBLY SET SCREW 7 A036 PRESSER FOOT SET SCREW 7 E08- THREAD TAKE-UP LEVER CAM SET PIN 8 W0 INSIDE PRESSER FOOT 8 W08- CRANK ROD LEVER CAM FOLLOWER 8- B03- ZIG ZAG PRESSER FOOT 9 W08- CRANK ROD LEVER CAM FOLLOWER ADJUST NUT 9 A035- PRESSER BAR 0 W08-3 CRANK ROD LEVER CAM FOLLOWER LOCK SCREW 30 B08 PRESSER BAR LOWER BUSHING W08- CRANK RO D LEVER CAM FOLLOWER LOCK NUT 3 W039 PRESSER BAR BRACKET E00 THREAD TAKE-UP ASSEMBLY 3 A06 PRESSER BAR ACTUATOR GUIDE SCREW 3 E0O- NEEDLE BAR CONNECTING ROD SET SCREW 33 W03 TENSION RELEASE LEVER DRAG LINK B08 NEEDLE BAR CONNECTING ROD 3 D00 TENSION RELEASE LEVER DRAG LINK SET PIN 5 A0 NEEDLE BAR CONNECTING STUD 35 W05 TENSION RELEASE LEVER 6 A09 NEEDLE SET SCREW 36 806 TENSION RELEASE LEVER SET SCREW 7 A03 PRESSER REGULATING THUMB SCREW 37 W06 ZIGZAG CONNECTING ROD SET BASE 8 WO0 PRESSER REGULATING THUMB SET SCREW 38 WO65 PRESSER BAR ACTUATOR CAM 9 A03 PRESSER BAR SPRING 0 B06 NEEDLE BAR SUPPORT
GROUP 3 SHUTTLE TRANSMISSION GROUP 9 9 5 6 8 3 5 0 9 9 0 7 3 6 6 8 7 5
GROUP 3 KEY NO. PART NO. PART NAME Q TY B39 CRANK CONNECTING ROD A07B CRANK CONNECTING ROD SET SCREW 3 A078 CRANK CONNECTING ROD SET NUT A03 OSCILLATING SHAFT SET SCREW & NUT 5 A0 OSCILLATING SHAFT 6 A08 SHUTTLE DRIVER PIN OSCILLATING SHAFT CRANK SET PIN 7 A0 OSCILLATING SHAFT CRANK SET SCREW 8 B79 OSCILLATING SHAFT CRANK. WITH SLIDE BLOCK 9 B77 LOWER SHAFT COLLAR 0 B55 SHUTTLE RACE GUIDE A08 SHUTTLE RACE GUIDE SHAFT B53 SHUTTLE RACE GUIDE SHAFT SET SCREW 3 B70 SHUTTLE RACE GUIDE SHAFT COMPLETE B7 LOWER SHAFT 5 Wl7 SHUTTLE DRIVER 6 D099 SHUTTLE HOOK 7 A07 BOBBIN 8 D00 BOBBIN CASE ASSEMBLY 9 B39- CRANK CONNECTING ROD CAP SET SCREW 0 B77- LOWER SHAFT COLLAR SET SCREW 6
GROUP FEED TRANSMISSION GROUP 6 7 3 8 5 9 0 0 8 3 7-7 5 9 5 6 3 7
GROUP KEY NO. PART NO. PART NAME Q TY KEY NO. PART NO. PART NAME Q TY W09 FEED REGULATOR THUMB NUT 3 A07IB- FEED ROCK SHAFT CRANK SET SCREW FEED LIFTING ROCK SHAFT CRANK SET SCREW WIO5 FEED REGULATOR LEVER A067 FEED REGULATOR SCREW WASHER 3 A053B- FEED REGULATOR LEVER NUT 7- W0 ZIG ZAG FEED DOG W07 FEED REGULATOR 5 WO6 FEED REGULATOR SPRING 6 B00 FEED REGULATOR SCREW SET SCREW 7 W08 FEED REGULATOR SCREW 8 A069B FEED CONNECTION SLIDE BLOCK 9 A069A FEED CONNECTION SLIDE BLOCK STUD 0 B03 FORKED ROD A03 FEED ROCK SHAFT CENTER SCREW & NUT FEED LIFTING ROCK SHAFT SCREW & NUT W06 DRIVING CRANK 3 A07B FEED ROCK SHAFT CRANK A07A FEED ROCK SHAFT 5 A076 FEED BAR CENTER SCREW & NUT 6 A075 FEED BAR 7 WO FEED DOG 8 A078 FEED DOG SCREW 9 W06- DRIVING CRANK GUIDE NUT 0 AD6 DRIVING CRANK GUIDE SCREW A07 FEED LIFTING ROCK SHAFT A073 FEED LIFTING ROCK SHAFT CRANK 8
GROUP 5 DRIVING & REVERSING MECHANISM GROUP 30 0 39 38 3 9 37 3 3 5 38 33 36 35 38 3 30 3 37 8 38 7 9 7 0 3 8 5 6 8 0 6 9 9 0 6 3 7-5 6 7 9
GROUP 5 KEY NO. PART NO. PART NAME Q TY KEY NO. PART NO. PART NAME Q TY W0 PRESSER BAR LIFTER C097 BRACKET SET SCREW W0-3 PRESSER BAR LIFTER HINGE SCREW 5 W036 PRESSER BAR FEED ROD 3 W06 LIFT BAR 6 W0- PRESSER BAR ACTUATOR SPACER W0- UPPER LIFT BAR SCREW 7 W0 END PLATE BEARING SET PLATE 5 W0- SPACER 8 W0- REVET 3 6 W06- LIFT BAR GUIDE SCREW 9 W0 BEARING BRACKET BUSHING 7 WO8 PRESSER BAR TRACK 30 W03 LIFT CRANK ROD BEARING BRACKET PLATE 8 WO8- PRESSER BAR TRACK HINGE SCREW 3 W05 ROCKER END SET RING 9 W00 REAR PRESSER BAR BRACKET 3 W05- ROCKER SET RING SET SCREW 0 A09 REAR PRESSER BAR SET SCREW 33 W033 PRESSER BAR ACTUATOR UP-DOWN ROCKER W08- PRESSER BAR TRACK GUIDE SCREW 3 W03 PRESSER BAR ACTUATOR FEED ROCKER W08-3 PRESSER BAR TRACK FEED STUD 35 W035 CRANK ROD ROCKER 3 W09- PRESSER BAR LOAD SPRING (REAR) 36 W053 CRANK ROD 5 6 7 W09 WO7 BOO W03 REAR PRESSER BAR OUTSIDE PRESSER FOOT BRACKET OUTSIDE PRESSER FOOT BRACKET SCREW OUTSIDE PRESSER FOOT SET SCREW OUTSIDE PRESSER FOOT 37 38 39 D97 W03-3 W06- PRESSER BAR ACTUATOR UP-DOWN ROCKER SET SCREW CRANK ROD ROCKER SET SCREW PRESSER BAR FEED ROCKER SET SCREW CRANK ROD ROCKER GUIDE SCREW UP-DOWN ROCKER GUIDE SCREW 8 W0 PRESSER BAR ACTUATOR 0 W06-3 CRANK ROD ROCKER LOCK SPACER UP-DOWN ROCKER LOCK SPACER 9 0 W00- W00- FEED SCREW RING PRESSER BAR ACTUATOR FEED SCREW W06- CRANK ROD ROCKER LOCK WASHER UP-DOWN ROCKER LOCK WASHER W0 END PLATE A06-B CRANK ROD ROCKER LOCK NUT UP-DOWN ROCKER LOCK NUT W0- END PLATE SET SCREW 7- WO3- ZIG ZAG OUTSIDE PRESSER FOOT 3 W0 OUTSIDE PRESSER FOOT BRACKET LIMITATOR 0
GROUP 6 ELECTRIC POWER & DYNAMIC TRANSMISSION 3 8 7 6 8 3 0 7 5 5 6 3 8 0 5 9 3 9 8 7 6 5
GROUP 6 KEY NO. PART NO. PART NAME Q TY KEY NO. PART NO. PART NAME Q TY AOO STOP MOTION CLAMP STOP SCREW 3 W09- MOTOR BASE SET SCREW AOO- STOP MOTION CLAMP SCREW W09- MOTOR SET WASHER 3 A005 STOP MOTION CLAMP WASHER 5 C097 MOTOR SET SCREW A003 BALANCE WHEEL BUSHING 6 W003 MOTOR 5 A006 BALANCE WHEEL BUSHING SET PIN 7 W06- MOTOR PULLEY 6 W060 HAND WHEEL 8 D097 MOTOR PULLEY SET SCREW 7 WOO6 BELT (30XLO.8) 8 WOO7 BELT (80XLO.5) 9 D6 E5 RING 0 W06-5 IDLE PULLEY SHAFT WASHER W06- IDLE PULLEY SHAFT W06-3 IDLE PULLEY 3 W06- IDLE PULLEY BEARING W06-6 IDLE PULLEY LOCK WASHER 5 W06- IDLE PULLEY SET NUT 6 W059 PULLEY BRACKET 7 LT-M- MOTOR BRACKET SET WASHER 8 LT-M-3 MOTOR BRACKET SET LOCK WASHER 9 LT-M- MOTOR BRACKET SET SCREW 0 W050 BELT COVER A09 BELT COVER SET SCREW W09 MOTOR BASE (REAR COVER)
GROUP 7 ZIG ZAG MECHANISM GROUP 5 5 0 8 9 5 7 6 5 3 5 8 6 7 3 0 3 5 5 6 7 3
GROUP 7 KEY NO. PART NO. PART NAME Q TY KEY NO. PART NO. PART NAME Q TY 703 ZIG ZAG CAM & GEAR (ASSEMBLY) 3 H777 ZIG ZAG CONTROL PLATE 70 SET SCREW (3) FOR NO. 703, 707 - SET SCREW FOR NO. 75() 3 705- NEEDLE DISPLACEMENT REGULATOR (ASSEMBLY) 5 5 SET SCREW FOR NO. M7(), M79(), M73(), N77(), H777() 7 707 SHAFT FOR NO 705-6 0- SET SCREW FOR NO. M73() 5 708 ZIG ZAG WIDTH REGULATOR 7 0 SET SCREW FOR NO. 78( ) 6 709 ZIG ZAG WIDTH REGULATOR PIN () FOR NO. 708, M7 7 8 9 0 70 M7 M7 78 SET SCREW FOR NO 708() ZIG ZAG CONNECTING PLATE ZIG ZAG REGULATING LEVER SPRING WASHER FOR NO. 709 TO REGULATE THE WIDTH OF ZIGZAG STITCH Moving the zigzag width lever to the desire zigzag width as marked on the panel accordingly can regulate the zigzag width. For instance, 0 as straight while 5 will be the maximum zigzag width 3 D70 75 75-7 ZIG ZAG WIDTH LEVER KNOB () ZIG ZAG CONNECTING LINK SLIDE BLOCK (ASSEMBLY) COLLAR FOR NO. 75 NEEDLE POSITION SELECTION With the zigzag width lever set at 0 and the needle position selector move to L, a straight line stitches will be sewn at the left side of the needle hole. M76 ZIG ZAG VERTICAL SHAFT With the zigzag width lever set at 0 and the needle position selector move to C or R, a straight line stitches will be sewn at the middle or the right of the needle hole. 5 77 SNAP RING FOR NO. M76 () As adjusting of zigzag width with the needle position selection as mentioned above, a variety of ornamental stitches can be sewn. 6 78 ZIG ZAG VERTICAL SHAFT ARM 7 M79 NEEDLE POSITION COMPLETE LEVER L C R 8 M73 CLICK STOPPER FOR NO. M79 9 M73 NEEDLE POSITION COMPLETE LEVER GUIDE 0 7 SNAP RING () FOR NO. 707 N76 SPRING FOR NO. M7 C79 ZIG ZAG REGULATING LEVER PIN
BASE PLATE & WORKING PLATE KEY NO. PART NO. PART NAME Q TY E36 HEAD SCREW A06 BASE SlDE SET SCREW 3 E8 BASE SIDE PRESSER PLATE W8- BASE SIDE PRESSER PLATE RUBBER 5 E5 BASE SHAFT SET SCREW 6 E3 BASE SHAFT 7 E7 BASE PRESSER PLATE 8 E33 BASE PRESSER PLATE RUBBER 9 E9 PRESSER PLATE SET SCREW 0 E3 SHIM SPRING W0 BASE COVER E3 PRESSER PLATE SET NUT 3 E RUBBER PACKING E9 SIDE PRESSER PlATE SET SCREW 5 E8 BIG WORKING PLATE 6 E09 WORKING PLATE 7 E3 LEG 6
CUDA CRANK INSTALLATION STOP MOTION SCREW HAND WHEEL Unscrew & remove the stop motion stop screw with screw driver. By hand, unscrew & remove the stop motion screw. 3 Remove clamp washer from under the stop motion screw. SCREW DRIVER CLAMP WASHER DRIVE BELT COVER Remove the drive belt cover held by two screws. MAIN BELT 5 Remove longer main belt. Turn hand wheel to assist removal. 6 Remove the hand wheel. Wheel slides off. 7
NEW BELT BIG WHEEL 7 Install the BIG WHEEL on the end of the shaft making sure that the teeth on the wheel are facing the sowing head. 8 Tighten the BIG WHEEL on the /8 Allen key provided. /8" ALLEN KEY 9 Install the new mail drive belt. Slip the drive belt over the BIG WHEEL first and then slip the belt over the small idle pulley at the back. Turn the small pulley slowly clockwise to make sure that the belt is properly in place. ALLEN SCREW 0 Put back in place the stop motion screw & clamp motion washer. Put back in place the stop motion clamp stop screw. Install the new belt cover on by two screws. 5/3" ALLEN KEY HANDLE NEW DRIVEŁ BELT COVER For hand crank operation only, install the handle to the BIG WHEEL by tightening the Allen screw with the 5/3 Allen key provided. 8
OPTIONAL CUDA CASE 3/ plywood construction Reinforced metal corner guards Heavy-duty handle Dual exterior case latches Separate insert houses the accessory kit for extra needles, bobbins and more 9
RELIABLE CORPORATION 3-YEAR PRODUCT WARRANTY POLICY FOR THE BARRACUDA SEWING MACHINE (MODEL 00ZW) Reliable Corporation ( Reliable ) warrants to the original purchaser of the boiler noted above from Reliable (the Barracuda ) that for a period of three (3) years from the date of purchase it will be free from defects in materials and workmanship when utilized for normal use by the original purchaser only. Subject to the conditions and limitations set forth below, Reliable will either repair or replace any part of a Barracuda that proves defective by reason of improper workmanship or materials. If the defective Barracuda is no longer available and cannot be repaired effectively or replaced with an identical model, Reliable shall replace the defective Barracuda with a current Barracuda of equal or greater value. Repaired parts or replacement products will be provided by Reliable on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. If Reliable is unable to repair or replace a Barracuda, it will refund the current value of that Barracuda at the time the warranty claim is made. This limited warranty does not cover any damage to a Barracuda that results from improper installation, accident, abuse, misuse, unreasonable use, natural disaster, insufficient or excessive electrical supply, abnormal mechanical or environmental conditions or any unauthorized disassembly, repair or modification. This limited warranty does not extend to any indirect, consequential or incidental damages that may be suffered by a user from the use of a Barracuda, including without limitation, any liability for third party claims for damage, and is limited to the amount paid by the original purchaser for the Barracuda with respect to which this limited warranty protection applies. This limited warranty does not apply with respect to products that have been altered or products not purchased directly from Reliable or a dealer authorized by Reliable to sell the Reliable Barracuda. This limited warranty is the only warranty that applies to the Reliable Barracuda, sewing machine, supersedes any and all terms that may be contained in any other document or purchase order and may not be altered or amended except expressly in writing by Reliable. To obtain a repair or replacement under the terms of this warranty, please contact our customer service group at 800 68 69. You will be required to submit an original receipt via fax or e-mail. The receipt must reflect that you are the original purchaser, the product was bought directly from Reliable or from an authorized Reliable dealer and that the warranty claim is being made in compliance with the terms set out in this document or any subsequent document issued by Reliable in connection with this policy. You will be issued a return authorization number (RA#) and asked to ship the defective product together with proof of purchase and RA#, prepaid insured to the following address: Reliable Corporation, 5 00 Wingold Ave, Toronto, ON M6B K7. Freight collect shipments will be refused. The risk of loss or damage in transit will be borne by the customer. Once Reliable receives the defective product, it will initiate the repair or replacement process. If you have any questions regarding this warranty, you may write to: Reliable Corporation 00 Wingold Avenue, Unit 5 Toronto, Ontario Canada M6B K7 www.reliable corporation.com
RELIABLE CORPORATION PRODUCTS WARRANTY Reliable Corporation ( Reliable ) warrants to the original purchaser of its products that every product sold by Reliable (a Reliable Product ) is free from defects in material and workmanship for a period of one year from the date of purchase if properly used and maintained. Subject to the conditions and limitations set forth below, Reliable will either repair or replace any part of a Reliable Product that proves defective by reason of improper workmanship or materials. If the defective Reliable Product is no longer available and cannot be repaired effectively or replaced with an identical model, Reliable shall replace the defective Reliable Product with a current Reliable Product of equal or greater value. Repaired parts or replacement products will be provided by Reliable on an exchange basis, and will be either new or refurbished to be functionally equivalent to new. If Reliable is unable to repair or replace a Reliable Product, it will refund the current value of that Reliable Product at the time the warranty claim is made. This limited warranty does not cover any damage to a Reliable Product that results from improper installation, accident, abuse, misuse, natural disaster, insufficient or excessive electrical supply, abnormal mechanical or environmental conditions, wear and tear resulting from normal use of the product, or any unauthorized disassembly, repair, or modification. This limited warranty does not extend to any indirect, consequential or incidental damages that may be suffered by a user or from the use of a Reliable Product, including without limitation, any liability for third party claims for damage, and is limited to the amount paid by the original purchaser Reliable Product with respect to which this limited warranty protection applies. This limited warranty does not apply with respect to products that have been altered or which are missing serial numbers or for products not purchased directly from Reliable or a dealer authorized by us to sell Reliable Products. This limited warranty is the only warranty that applies to any Reliable Product, supersedes any and all terms that may be contained in any other document or purchase order and may not be altered or amended except expressly in writing by Reliable. To obtain a repair or replacement under the terms of this warranty, please contact our customer service group at -800-68-69 or at support@reliablecorporation. com. You will be required to submit an original receipt via fax or e-mail. The receipt must reflect that you are the original purchaser, the product was bought directly from us or from an authorized Reliable dealer and that the warranty claim is being made within the warranty period. You will be issued a return authorization number (RA#) and asked to ship the defective product together with proof of purchase and RA#, prepaid insured to the following address: Reliable Corporation, 5-00 Wingold Avenue, Toronto, ON M6B K7. Freight collect shipments will be refused. The risk of loss or damage in transit will be borne by the customer. Once Reliable receives the defective product, it will initiate the repair or replacement process. If you have any questions regarding this warranty, you may write to: Reliable Corporation 00 Wingold Avenue, Unit 5 Toronto, Ontario Canada M6B K7 www.reliablecorporation.com
800 68 69 www.reliablecorporation.com