www.hogfors.com Airvec deaerator is technically advanced, easy-to-use product with simplistic design and unmatched installability. Airvec Deaerators For Heating and Cooling Systems HögforsGST
Please note before choosing your deaerator: Air / oxygen can cause several issues in heating and cooling systems. Among the most common problems are corrosion, reduced component service life, reduced heat transfer and increased noise. Key factors: Installability Ease of use Living comfort (no excessive noise) Serviceability Airvec deaerator benefits: Premium components Minimized risk of corrosion Extended life cycle of components Improved heat transfer Reduced commissioning time Fast delivery time Three-year () warranty Selecting the correct deaerator for your property requires expert guidance. AirVec operating principle and separating capability (PN0//) AirVec removes loose and dissolved air as well as particulate impurities. Inside the AirVec unit, the water's flow rate decreases rapidly, effectively separating microbubbles and particulates. Air bubbles automatically rise to the air bleeding valve at the top while particles that are heavier than water sink to the bottom of the unit. AirVec deaerators remove all microbubbles starting from μm. AirVec units equipped with dirt separation also remove particulate impurities as small as μm. Model indications Airvec 0-NSW- Pressure Category, 0=0 bar, = bar, = bar Connection, W=welded, F=flanged, G=threaded Material, S=steel, H=stainless, B=brass Model, N=normal, E=extra, O=open Pipe size (dn) Product family name
h Dimensions Airvec DN0-DN0 Airvec G /" - G" H DN H DN d ØD L h Airvec technical data G /" - G" Connection size DN (internal thread) G /" /" " d ØD L Lf H mm 0 0 h mm 0 0 d (internal thread) G ½" ½" ½" ØD mm 9 9 00 L mm 00 00 0 Lf mm - - - Flow rate l/s,0,,8 Weight kg,8,7, Airvec technical data DN0-DN0 Connection size DN (flange DIN) /mm (weld.) DN0 / Ø0. DN / Ø7. DN80 / Ø88.9 DN00 / Ø. DN / Ø9.7 DN0 / Ø8. DN00 / Ø9. DN0 / Ø7 H mm 778 778 89 9 h mm 9 9 999 999 70 H extra mm 7 7 80 80 09 09 00 h extra mm 0 0 8 8 8 9 H open mm 0 0 80 80 0 0 h open mm 09 09 9 9 8 8 9 d (internal thread) G ½" ½" ¾" ¾" " " " " ØD mm 8 8 9 9 0 08 L mm 8 8 99 9 78 Lf mm 0 9 0 0 7 8 Flow rate l/s,,, 8,,9 0,8,7, Weight weld./flange kg 9/ 9/ 7/ 7/ / /7 89/0 /8 Weight extra weld./flange kg 0/ 0/ 9/ 9/8 7/9 7/ 97/9 /9 Weight open weld./flange kg 9/ 9/ /0 / 9/8 9/8 /7 97/9 All Rights Reserved
Construction. AirVec include automatic vent valve (Flexvent PN0), which is provided with a shut-off valve part whereby the vent valve can be closed. (Flexvent Max PN/), which is provided with a set screw whereby the vent valve can be closed. The outlet of the Flexvent MAX has a millimetre connection for a drainage pipe. The lifting lugs allows for easy installation. AirVec's unique FoxisTube is designed to remove even the smallest micro bubbles and small particles of dirt without the flow resistance increases too much. Body: - PGH (EN 07-), - Exterior coating: RAL 70, coating thick. of > 0 μm. Storage range is up to DN0 (7mm) Weld end and the flanges - Weld ends: PGH (EN 07-), - Flanges: EN 09- (PN / PN). Thanks to large precipitate housing the drain interval is long 7. AirVec is provided with flush valve, (½ "- " PN0) (Naval ball valve (DN / ½ "- DN / " PN/) which the dirt is collected on the bottom may be removed when the system is in use PN0 PN- 7 7 All Rights Reserved
Equipment Standard equipment: Automatic deaerator Drain valve Additional materials and sizes available on demand. Airvec DN - DN0 For network deaeration. Can also be used for dirt separation. Sizes DN0 DN0 available in steel with welded connections / flanges. Also available in other materials. Sizes DN DN0 (G/" - G") available in brass, threaded connections. Max. operating temperature0 C. Max. operating pressure 0// PN. Airvec extra DN0 - DN0 For network deaeration dirt separation. Available in steel, welded connections / flanges. Also available in other materials. Max. operating temperature0 C. Max. operating pressure 0// PN. Airvec open DN0 - DN0 For network deaeration and dirt separation in locations with above average precipitation. Available in steel, welded connections / flanges. Also available in other materials. Max. operating temperature0 C. Max. operating pressure 0// PN. All Rights Reserved
Flow resistance dn0 dn dn80 dn00,, pressure drop kpa,,, recommended max. pressure drop level 0, 0 0,0,,0 7, 0,0,,0 7, 0,0, flow rate l/s v= m/s dn dn0 dn00 dn0,, pressure drop kpa,,, recommended max. pressure drop level 0, 0 0,0 0,0 0,0 0,0 0,0 0,0 0,0 70,0 80,0 90,0 00,0 0,0 0,0 0,0 0,0 flow rate l/s v= m/s
Flow resistance G/ G/ G,, pressure drop kpa,,, recommended max. pressure drop level 0, 0 0 0,,,,, flow rate l/s v= m/s All values are max. values.
HögforsGST International heating system expertise HögforsGST specializes in the manufacture, sale and marketing of high-quality heating systems. The company has solid experience in heating systems both domestically and in export markets. Our professionalism is based on experience in production, serial manufacture, mass tailoring and project production as well as HVAC procurement channel and logistics expertise in Finland and abroad. Our operations are based on determining requirements for sustainable business operations on the market, customer-orientedness and reliability. We are equally uncompromising in terms of our high-quality products and services. Three-year warranty and fast delivery time: All Airvec deaerators and components come with a three-year warranty. Our products are not only premium quality; Airvec deaerators are also delivered fast! Ensuring fast delivery times is a key part of our operations. HögforsGST Manufacturer: HögforsGST Oy Tel. +8 (0)00 78 00, Fax +8 (0)7 00 www.hogfors.com P.O. Box (Pohjukansalontie ), FI-790 Leppävirta, Finland info@gst.fi