ARGUS presence detectors. Move towards energy efficiency

ARGUS presence detectors Move towards energy efficiency

Energy consumption will dramatically increase within the next 20 years Solutions based on energy-efficient products are requested more and more 2 Move towards energy efficiency ARGUS presence detectors

Content Functionality 4 Applications 8 ARGUS Presence detector system 10 ARGUS Presence detector system Technical overview 14 Stand-alone detectors 16 Stand-alone detectors Technical overview 18 ARGUS presence detectors Move towards energy efficiency 3

Keeping energy costs down Continuously rising energy prices are the result of a changed global energy situation. Energy-efficient products are more important and more in demand than ever, because saving is the only way to conserve resources and reduce costs. Only consuming energy when it is needed helps the environment Understanding and reducing energy usage The desire to have products that save energy in a simple and convenient manner is growing constantly. In addition, more and more standards and directives demand the use of energy-efficient solutions. Presence detectors from Schneider Electric avoid unnecessary energy consumption and contri bute significantly to cost savings in offices, schools, hospitals and any kind of public building. Energy efficiency classes According to the Energy Performance for Buildings Directive (BS EN 15232:2012), with the installation of presence detectors, the energy efficiency class B will be achieved. This standard assesses the efficiency of buildings, through the use of standardised calculation methods. The use of electricity and primary energy sources within buildings contributes to over 21% of global greenhouse emissions. Efficient energy usage within a building is therefore essential at a time when energy prices are increasing and building occupiers are becoming more environmentally conscious. High Performance Integrated room/zone control; energy management Advanced Occupancy management with automatic light control Standard Key functions like dimmers No Efficiency Switches only Simply reach energy efficiency class B with Schneider Electric presence detectors 4 Move towards energy efficiency ARGUS presence detectors

Make a move towards energy efficiency ARGUS presence detectors Move towards energy efficiency 5

Presence detectors for all areas of application Presence detectors automatically switch the light on and off depending on brightness and movement. If required, other loads such as heating and ventilation can also be switched on and off. This is not only convenient but energy efficient as well. Install presence detectors for maximum comfort and efficiency The presence detector senses movement and switches the light on depending on ambient brightness. Unlike a movement detector, it also switches the light back off when the area is bright enough. As a result, the presence detector is especially suitable for rooms that are used for longer periods and that receive a high proportion of daylight. Presence detector system The ARGUS presence detector range from Schneider Electric offers efficient stand-alone and system solutions for the different requirements of your customers: daylight harvesting for consistent brightness by the use of 1-10V and DALI as well as the control of heating or ventilation. Networking presence detectors increases the detection areas, thus providing a close detection of larger rooms and areas as required. Cost-efficient presence detector systems can be achieved by combining one master with up to 10 slaves. Ceiling presence detector 360 detection angle 14 m detection range 10s to 30 min overshoot time 10-1000 Lux brightness threshold Staircase timer Angle of detection 360 14 m Detection range ARGUS Presence relay Master 1 or 2 channel options Brightness independent 2nd channel for heating or ventilation IR function ARGUS Presence 1-10V Master Daylight harvesting IR function ARGUS Presence DALI Master Daylight harvesting IR function ARGUS Presence Slave Up to 10 Slaves per Master 4 outputs for connecting to networks SideController Auto mode/light on/off for 24h and in case of 1-10V or DALI presence detectors change triggering set points (dimming up or down) IR Remote control Auto mode/light on/off for 24h and in case of 1-10V or DALI presence detectors change triggering set points (dimming up or down) PL Expander Safety module to protect against electrical shock when several circuit breakers are used to protect lighting circuits Surface-mounted housing 6 Move towards energy efficiency ARGUS presence detectors

Functions Whether in stairwells, meeting rooms or open-plan spaces presence detectors from Schneider Electric are suitable for many different applications. With practical functions, possible settings and large areas of detection, you offer your customers the right solution for energy efficiency and comfort. Using presence detectors can automatically save your customers money Master/Slave Up to 10 masters and 10 slaves can be interconnected via a single core 230V cable. This means long corridors and large stairwells are easy to monitor. Control via a retractive switch The overshoot time that has been set can be activated via a retractive switch. Staircase timer Depending on requirements, the staircase timer can be infinitely adjusted between 10 seconds and 30 minutes. The switchable prewarning function shows the remaining overshoot time 30 seconds before. P P P P Master Slave Slave Switching with warning Dimming with warning Overshoot time Warning time (30 seconds) Daylight harvesting (1-10V and DALI) Lighting control ensures the desired brightness in a room is continually achieved. The brightness of the lighting is kept nearly constant depending on daylight, by dimming the connected lighting group. Remote controllable The ceiling-mounted ARGUS presence detectors can be easily operated with the remote control: switching-maintained light on/off, switching to automatic mode as well as dimming up/down for 1-10V and DALI. Two channels for integrating heating or ventilation The ARGUS Presence relay 2-gang presence detector has a brightness-dependent channel and a brightness-independent channel. The first channel automatically controls the lighting depending on brightness and presence. The second channel controls connected loads such as heating or ventilation depending on presence only. ARGUS presence detectors Move towards energy efficiency 7

Applications Owing to the number of rooms with various uses, commercial buildings provide plenty of options to achieve high levels of energy-saving potential. The movement and brightness-dependent control of lighting, temperature and ventilation can be perfectly adapted to the user s behaviour. Single office & open plan spaces Optimal conditions for high efficiency Optimum lighting of open plan spaces increases comfort and efficiency. Lights switch on depending on move ment and brightness. Thanks to the daylight harvesting function, lighting is dimmed to a defined light level. In case brightness is sufficient the ARGUS presence detector switches off the lights, even if people are present. Store rooms / rest rooms Plenty of room for energy saving Store rooms or rest rooms are among the least-used spaces. It is easy to forget to turn off the lights when leaving such rooms, making a presence detector a very efficient solution. When entering the room, the presence detector conveniently switches on the light and then switches it off automatically when no movement is detected. 8 Move towards energy efficiency ARGUS presence detectors

Corridor Conference room Presence detectors with two channels offer high convenience with maximum energyefficiency Security in frequently used walkways If the presence detectors are installed one by one and linked together, lighting for the entire corridor is secured, regardless from which side it is entered. As soon as the presence detector ceases to register any movement, the lights are switched off. This simple solution provides dual efficiency as it increases security whilst reducing electricity costs. Two channels for double efficiency Be it for staff meetings or presentations, auto matic control ensures that the lighting and temperature in conference rooms is right so the occupants can focus on the more important issues at hand. The ARGUS PIR ensures twice the efficiency. With its two channels, the lighting and temperature can be set separately. This provides convenience with maximum energy efficiency. Daylight harvesting Directors office Open-plan office Lounge Meeting room Corridor Copy room / Archive Integration of temperature and ventilation Single office and open plan spaces Store rooms / rest rooms Corridor Conference room Daylight harvesting for perfect lighting Optimised energy consumption in infrequently used rooms Master-Slave function for complete detection, even in long or L-shaped corridors Manual control of lighting, if required for meetings and presentations DALI and 1-10V 1-10V or the digital standard DALI are lighting control systems often used in commercial buildings. Integrating presence detectors makes it possible to have energy-efficient and needs-based illumination of all kinds of spaces. From individual to open-plan offices, lighting groups can be controlled according to presence. ARGUS presence detectors Move towards energy efficiency 9

ARGUS presence detection system Indoor presence detector range for ceiling mounting. The sensor module detects moving heat sources (e.g. people) within an adjustable area of detection and starts a staircase timer. The sensor module is equipped with a light sensor with an adjustable brightness threshold so that the lighting is only switched on when a specified brightness threshold is not met. When there is sufficient natural light, the presence function allows the sensor module to switch off the lighting even when a person is present. Designed for installation into a 50mm deep round back box or in the surface-mounted housing available as an accessory. With screw terminals and claw & screw fixing. ARGUS Presence Master with IR, relay 1-gang Colour MTN55101119 Polar White For ohmic, inductive and capacitive loads such as incandescent lamps, energy-saving lamps, LV halogen lighting with conventional transformer, electronic transformers, fluorescent lamps. Switching of one output External triggering via one PL-input (Slaves) Switching Brightness-dependent staircase lighting function ARGUS Presence Master with IR, relay 2-gang Colour MTN55101219 Polar White For ohmic, inductive and capacitive loads such as incandescent lamps, energy-saving lamps, LV halogen lighting with conventional transformer, electronic transformers, fluorescent lamps. Switching of two outputs External triggering via two PL-inputs (Slaves) Switching Brightness-dependent staircase lighting function with channel 1, staircase lighting function independent of brightness with channel 2 10 Move towards energy efficiency ARGUS presence detectors

ARGUS presence detection system ARGUS Presence Master with IR, 1-10V Colour MTN55101419 Polar White For fluorescent lamps with electronic ballast or electronic transformer with 1-10 V interface. The switchable light control ensures that the room illumination remains almost constant. The sensor module continuously measures the brightness in the room and adjusts the illumination to an adjustable setpoint. Switching and dimming of one output External triggering via one PL-input (Slave) Memory function Brightness-dependent staircase lighting function, light control ARGUS Presence Master with IR, DALI Colour MTN55101519 Polar White For triggering up to 15 DALI EBs. The switchable light control ensures that the room illumination remains almost constant. The sensor module continuously measures the brightness in the room and adjusts the illumination to an adjustable setpoint. Switching and dimming of DALI EBs External triggering via one PL-input (Slave) Overload and short-circuit-proof Memory function Up to 6 DALI control inserts can be connected to one DALI line. However the maximum number of 64 DALI EBs and a cable length of 300 m must not be exceeded Brightness-dependent staircase lighting function, light control ARGUS Presence Slave Colour MTN55701019 Polar White For triggering all ARGUS Presence Master. The device has four PL-outputs. The control function via PL requires a separate core in the installation to the receiving master devices for each PL line. Global control via four PL-outputs Staircase lighting function independent of brightness ARGUS presence detectors Move towards energy efficiency 11

ARGUS presence detection system Side controller Plus, 2-gang, complete unit Colour MTN51290319 Polar White, Glossy In M-SMART design. For triggering all ARGUS Presence Master. The device has one PL-output. The control function via PL requires a separate core in the installation to the receiving master devices. The control function via PL requires a separate core in the installation to the receiving devices. With screw terminals. With claw and screw fixing. Line control via one PL-output Triggering master devices (right buttons) Activating the 24h staircaise timer (left buttons) Nominal voltage: AC 220/230 V, 50/60 Hz Output: 1 x PlusLink Neutral conductor:not required (2 conductor system) Wire range: max. 2x2.5 mm² Accessories: PlusLink Expander CCTDT5130 Master: ARGUS Presence Master with IR, relay 1-gang MTN5510-1119, ARGUS Presence Master with IR, relay 2-gang MTN5510-1219, ARGUS Presence Master with IR, 1-10V MTN5510-1419, ARGUS Presence Master with IR, DALI MTN5510-1519 Surface-mounted housing for ARGUS Presence MTN550619 Colour Polar White Flush mounting back box ALB 71322 Colour 50mm deep 12 Move towards energy efficiency ARGUS presence detectors

ARGUS presence detection system IR remote control Distance 2010 Colour MTN570222 Black 10 channel IR remote control. For the control of all TELE sensor covers, blind push-buttons with IR receiver, presence detectors with IR receivers and KNX devices with IR receivers. Battery: 2 microcells (IEC LR 03, AAA) Range: up to 20 m Contents: Without battery. PlusLink Expander CCTDT5130 The PlusLink extension needs to be integrated into one or more PL-lines if these are protected by at least two circuit breakers. If a circuit breaker is triggered in the event of maintenance work or a fault, then the PlusLink expansion will disconnect the PlusLink line automatically as well. This is necessary because the PlusLink line would otherwise continue to be live via the other circuit breakers. With screw terminals. Suitable for installation on DIN rails TH35 according to EN 60715. Nominal voltage: AC 220/230 V Neutral conductor: required (3 conductor system) Wire range: max. 4 mm² Device width: 1 HP = 18 mm ARGUS presence detectors Move towards energy efficiency 13

Technical overview ARGUS Presence detector system Product reference MTN55101119 MTN55101219 Description Presence Master with IR, relay 1-gang Presence Master with IR, relay 2-gang Nominal voltage AC 220/230V, 50/60Hz AC 220/230V, 50/60Hz Nominal current max. 10AX, cosφ = 0.6 Max. 10AX, cosφ = 0.6. The total load on both channels is not allowed to exceed 14A Control current - - Type - - Load type - - Outputs 1 x make contacts 2 x make contacts Max. switching capacity per channel: Incandescent lamps 2200W 2200W HV halogen lamps 2000W 2000W LV halogen lamps with wound transformer 500VA 500VA Electronic transformers 1050W 1050W Capacitive load 10A, 140 μf 10A, 140 μf Energy-saving lamps 100VA 100VA Motor load 1000VA 1000VA Neutral conductor Required (3 conductor system) Required (3 conductor system) Cable capacity max. 2x2.5mm 2 max. 2x2.5mm 2 Angle of detection 360 o 360 o Number of levels 6 6 Number of zones 136 136 Number of movement sensors 4 4 Recommended installation height 2.5m 2.5m Range A radius of max. 7m (at an installation height of 2.5m) A radius of max. 7m (at an installation height of 2.5m) Sensitivity Continuously adjustable Continuously adjustable Brightness threshold Continuously adjustable between approx. 10 and 1000 lux Continuously adjustable between approx. 10 and 1000 lux Overshoot time Channel 1: continuously adjustable between approx. 10s and approx. 30min Channel 1: continuously adjustable between approx. 10s and approx. 30min Channel 2: continuously adjustable between approx. 5min and approx. 2h Slave ARGUS Presence Slave MTN55701019 ARGUS Presence Slave MTN55701019 14 Move towards energy efficiency ARGUS presence detectors

MTN55101419 MTN55101519 MTN55701019 Presence Master with IR, 1-10V Presence Master with IR, DALI Presence Slave AC 220/230V, 50/60Hz AC 220/230V, 50/60Hz AC 220/230V, 50/60Hz - - max. 10AX, cosφ = 0.6 max. 50mA - - - Category 1 control device - max. 25 controllable EBs (1-10V) max. 15 controllable DALI EBs - 1 x make contact, 1 x (1-10V) DALI output current: max. 30mA 4 x PL DALI output voltage: DC 15V 2200W - - 2000W - - 500VA - - 1050W - - 10A, 140 μf - - - - - - - - Required (3 conductor system) Required (3 conductor system) Required (3 conductor system) max. 2x2.5mm 2 max. 2x2.5mm 2 max. 2x2.5mm 2 360 o 360 o 360 o 6 6 6 136 136 136 4 4 4 2.5m 2.5m 2.5m A radius of max. 7m (at an installation height of 2.5m) A radius of max. 7m (at an installation height of 2.5m) A radius of max. 7m (at an installation height of 2.5m) Continuously adjustable Continuously adjustable Continuously adjustable Continuously adjustable between approx. 10 Continuously adjustable between approx. 10 - and 1000 lux and 1000 lux Channel 1: continuously adjustable between approx. 10s and approx. 30min Channel 1: continuously adjustable between approx. 10s and approx. 30min Channel 1: continuously adjustable between approx. 10s and approx. 30min ARGUS Presence Slave MTN55701019 ARGUS Presence Slave MTN55701019 - ARGUS presence detectors Move towards energy efficiency 15

Indoor stand-alone detectors Our range of ceiling devices can be discreetly mounted and incorporate a detection range of up to 360º, utilising a less obtrusive design approach and ensuring nothing is missed from view. These devices are available in either a single or dual load operation for the switching of heating and ventilation equipment. Dual-load 360 o PIR sensor SAEUEMSCDBWE Dual-load for switching heating & ventilation equipment, as well as lighting. RJ-12 plug and socket for a quick and easy connection Built-in red LED indicator for IR setting and easy test operation Single-load 360 o PIR sensor SAEUEMSCSAWE High performance relay for connecting all types of lights, e.g. fluorescent lamps, halogen lamps, incandescent etc Sensitivity is provided by a unique lens with no dead spot zones in its 360⁰ high intensity of detection Single-load 360 o PIR & ultrasonic sensor Infrascan single-load 120 o PIR sensors SAEUEMSCUWE Integrating PIR and ultrasonic technology, this device is a sophisticated detector, offering a highly effective solution for a wide variety of applications Occupancy is detected via frequency shifts caused by minor movements, such as typing or reading Ultimate screwless flat plate 90 o PIR plate switch E751 E751R The light and time can be adjusted to allow the devices to operate the load at any light level E751 offers 2 wire connection and 2A operation E751R offers 3 wire connection and 10A operation GUPA1411BSS GUP1411BSS Optional override facility Time adjustment of between 15 seconds and 30 minutes Aesthetic flat plate range design without unsightly fixings screws 16 Move towards energy efficiency ARGUS presence detectors

Outdoor stand-alone detectors Security lighting offers peace of mind, but to save energy, it doesn t need to be on all the time. PIRs are a great solution to offer the best of both worlds helping to keep you safe, whilst being kinder to the environment. The sensitivity of outdoor devices is fully adjustable to minimise false triggering, but ensuring the device reacts to all visitors and intruders. The light sensitivity level can be adjusted to ensure the lighting is activated at an appropriate level of darkness. Single-load 120 o PIR detector CCT56P004 High quality sensor with a 12m range, so you won t miss a thing Easy installation, with quick settings for switch-on time and light sensitivity levels Areas can be blanked out from the detection range Single-load 360 o PIR detector CCT56P008 12m detection range offers an extended line of vision, ensuring extra protection Operates in temperatures of -15ºC to 40ºC, making the device suitable for most weather conditions No earth wire cable is required, offering a straight forward installation Infrascan single-load 110 o PIR detector E750WPRGY 3 wire design Detection field up to 18 metres Includes separate mounting base (base includes conduit entries) ARGUS presence detectors Move towards energy efficiency 17

Technical overview Ceiling Mounted Product Code SAEUEMSCUWE SAEUEMSCSAWE SAEUEMSCDBWE E751 Product Description Single-Load 360 PIR and Ultrasonic Sensor Single-Load 360 PIR Sensor Dual-Load 360 PIR Sensor Infrascan single-load 120 PIR sensor Operating voltage 230V 50/60Hz 230V 50/60Hz 230V 50/60Hz 200-265V 50Hz Field of view 360 360 360 90 Range PIR 18m at 2.5m height UIS 10x16m 7m at 2.5m height 7m at 2.5m height 6m x 6m, 8.5m from sensor head. Head rotatable through 120 Mounting Ceiling (surface / flush) Ceiling (surface / flush) Ceiling (flush) Ceiling (surface) Single or Dual Load: Single Single Dual Single IR Remote Control* SAEUEMSIR10T X SAEUEMSIRWE X Incandescent 2000W 2000W 2000W 2A Halogen lamps 230V 1000W 1000W 1000W 2A Halogen w. Electronic transformer 1000VA 1000VA 1000VA 2A (iron core transformer only) Fluorescent tubes 900VA/100μF 900VA/100μF 900VA/100μF X Energy Saving lamps 900VA 900VA 900VA X IP class IP20 IP40 Flush IP44 Surface sensor IP40, power box IP20 IP44 Time setting 5 sec to 30 min 5 sec to 30 min Time 1 (for lighting): Adjustable from 5 sec to 20 min Time 2 (for HVAC): Adjustable from 10 sec to 60 min 5 sec to 20 min (user adjustable) Test Mode Yes Yes Yes Yes Lux setting 10-1000 Lux 10-2000 Lux 10-2000 Lux Continuous from 1 Lux to full sunlight Operating temp range 0 C to +45 C 0 C to +45 C 0 C to +45 C 0 C to +40 C Connection 3-wires 3-wires 3-wires 2 wires Parallel connection of Yes Yes Yes No detectors Switching modes Auto/Off Manual on X Auto mode, manual override Product Dimensions Ø111.5 x 72mm Ø111.5 x 43.5mm (flush) 68mmØ Cut-out Ø111.5 x 59mm Ø111.5 x 30mm (flush) 65mmØ Cut-out Ø80 x 16.5mm(H) 65mmØ Cut-out Ø 100 x 57mm(H) Finish White White White White 18 Move towards energy efficiency ARGUS presence detectors

Wall Mounted Outdoor E751R GUPA1411BSS GUP1411BSS E750WPRGY CCT56P004 CCT56P008 Infrascan single-load 120 PIR sensor Ultimate screwless 90 PIR plate switch - with override Ultimate screwless 90 PIR plate switch Infrascan single-load 110 PIR sensor Single-load 120 PIR sensor Single-load 360 PIR sensor 200-265V 50Hz 230V 50Hz 230V 50Hz 200-265V 50Hz 220-240V 50Hz 220-240V 50Hz 90 90 90 110 120 360 6m x 6m, 8.5m from sensor head. Head rotatable through 120 5m at 1.2m height 5m at 1.2m height 18m at 2.4m height 12m (forward) 12m Ceiling (surface) Wall (flush) Wall (flush) Wall or ceiling (surface) Wall or ceiling (surface) Wall or ceiling (surface) Single Single Single Single Single Single X X X X X X 10A 150W 150W 10A 1000W 1000W 10A 150W 150W 10A 900W 800W 10A 150VA 150VA 10A 250VA 315VA 10A X X 10A 200VA 250VA 500W X X 500W 4 x 23W 4 x 23W IP44 X X IP66 IP55 IP55 5 sec to 20 min (user adjustable) 15 sec 30 min (through 7 time increments) 15 sec 30 min (through 7 time increments) 5 sec to 20 min (user adjustable) Approx 3 sec 30 min, lower tolerance 2 6s Approx 5 sec 20 min, lower tolerance 2 8s Yes No No Yes Yes Yes Continuous from 10-2000 Lux 10-2000 Lux Continuous from 1 5 2000 Lux 5 2000 Lux 1 Lux to full sunlight Lux to full sunlight 0 C to +40 C +5 C to +25 C +5 C to +25 C 0 C to +50 C -15 C to +40 C -15 C to +40 C 3-wires 2 wires 2 wires 3-wires 3-wires 3-wires Yes Yes Yes Yes Yes Yes Auto mode, manual override Auto mode, manual override X Auto mode, manual override Ø 100 x 57mm(H) 88 x 88mm 88 x 88mm Mounting centres 84mm 145x74x110mm 180x95x147mm using mounting box White S/Steel Black interior S/Steel Black interior Auto mode, manual override With corner bracket 164mm (L) x 80mm (W) x 75mm (H) without corner brackets 140mm (L) x 80mm (W) x 75mm (H) Cool grey White White Auto mode, manual override With corner bracket 170mm (L) x 88mm (W) x 76mm (H) without corner bracket 142.5mm (L) x 88mm (W) x 76mm (H) ARGUS presence detectors Move towards energy efficiency 19

UK contact details - 0870 608 8 608 Fax 0870 608 8 606 Ireland contact details - 01 601 2200 Fax 01 601 2201 As the global specialist in energy management with operations in more than 100 countries, Schneider Electric offers integrated solutions across multiple market segments, including leadership positions in energy and infrastructure, industrial processes, building automation, and data centres/networks, as well as a broad presence in residential applications. Schneider Electric is dedicated to making individuals and organisations energy safe, reliable, efficient, productive and green from Power Plant to Plug TM. We are changing our brand names and becoming one Schneider Electric. You ll get the same great quality products, but from one name you can remember and trust. This provides you and your customers with the reassurance associated with Schneider Electric. Some of our market leading brands have already become Schneider Electric including Merlin Gerin, Telemecanique, Square D, GET, Mita, Sarel, Himel, Thorsman, Tower and TAC. Working as one Schneider Electric makes it clearer that our ranges are highly compatible for integrated solutions. Schneider Electric Ltd United Kingdom Stafford Park 5, Telford Shropshire TF3 3BL Tel: 0870 608 8 608 Fax: 0870 608 8 606 www.schneider-electric.com/uk Ireland Head office, Block a Maynooth Business Campus Maynooth, Co. Kildare Tel: (01) 601 2200 Fax: (01) 601 2201 www.schneider-electric.com/ie Schneider Electric Limited is a company registered in England and Wales. Registered number: 1407228. Registered office: Stafford Park 5, Telford, Shropshire TF3 3BL. 2013 Schneider Electric. All Rights Reserved. Schneider Electric, Active Energy Management, Compact, EcoStruxure, ION Enterprise, irio, Make the most of your energy, Masterpact, Micrologic, Power Plant To Plug, Modbus, and PowerLogic are owned by Schneider Electric Industries SAS, or its affiliated companies in the United States and other countries. LSB02986_EN As standards, specifications and designs change from time to time, please ask for confirmation of the information given in this publication. SE8127 AUG 2013 member of