P.O. BOX 5128 CONCORD, CA 94524 TM TROPICAL SHOWER TM WITH Bronze Finish Model SS710 Owner s Manual CONTENTS Choosing a Location to Place Your Shower...p. 2 Care Maintenance Instructions...p.2 Solar Uses...p.2 Part List...p.3 Assembly...p.4 Trouble Shooting...p.7 IMPORTANT! PLEASE READ THIS MANUAL CAREFULLY BEFORE PROCEEDING. AFTER READING THIS MANUAL, SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
1. CHOOSING A LOCATION TO PLACE YOUR SHOWER: Please read the important CAUTIONS and WARNINGS below before choosing a location to place your shower. 2. CARE MAINTENANCE INSTRUCTIONS: To properly clean the surface, wipe with a soft damp cloth, or sponge, using household soap or liquid detergent. During normal weathering, wood may crack slightly due to changes in the moisture. This does not effect the structural integrity of your product. Apply teak oil as needed to maintain its natural beauty. DO NOT use any cleaning products containing abrasives or solvents since these could damage the surface. HARSH CHEMICALS SHOULD NOT BE USED ON THE SURFACE. For extended life, store inside during winter. Burs or sharp edges may be lightly sanded smooth. Do not use any wood sealer that could create a slippery surface. 3. SOLAR USES: A dark color garden hose may be attached to the shower for added solar heating. This can create a short hot shower when done properly. (CAUTION: Always test the water temperature before use to avoid contact with water that may be too hot!)
Tropical Shower with Bronze Finish Owner s Manual 4. PART LIST:
5. ASSEMBLY STEP 1: Connect Bottom Tower (A) to the Base, by joining sockets together. For a tighter connection install screws through holes provided at rear of sockets. STEP 2: Connect Mid Tower (B) to Bottom Tower (A) in the same fashion as Step 1. STEP 3: Connect Top Tower (C) to Mid Tower (B) in the same fashion as Step 2.
Tropical Shower with Bronze Finish Owner s Manual STEP 4: Attach both Mounting Pegs to the Slider Bar by inserting the pegs into the ends of the Slider Bar as shown. STEP 5: Attach the Slider Bar to the tower assembly, using provided bolts and wing nuts. Tip use the longer bolt for the top and the shorter bolt for the bottom. STEP 6: Press the Mounting Peg Covers in to place over the Mounting Peg as shown. STEP 7: Attach Basket to Mid Tower (B) through preset holes, with provided nuts and bolts. STEP 8: Attach Foot Shower Mount through preset holes, to Bottom Tower (A) using provided hardware.
STEP 9: Attaching the Valve and Hose Connector. Remove the Flat washer and (1) Rubber washer from the Hose Connector part, leaving the metal washer and (1) rubber washer on the Hose Connector. Slide the threaded end of the Hose Connector through the hole in Mid Tower (B) from the back side. Next, press the rubber washer back onto the Hose Connector. Then tighten the Flat washer so the Hose Connecter is firmly connected to the panel. Finally, attach the valve to the threaded end of the Hose Connector. Be sure there is a small rubber washer in the nut on the valve before attaching. Tighten to prevent leakage. STEP 10 : Connect the tapered end of the Shower Hose to the Shower Head and the opposite end to the Valve. Make sure rubber washers are in place at both ends before attaching to Shower Head and Valve. STEP 11 : Connect a garden hose to the connector at the back of the shower. Make sure that a rubber washer is in place when attaching garden hose.
Tropical Shower with Bronze Finish Owner s Manual 6. Trouble shooting: PROBLEM: SOLUTION: Water is leaking around fittings. Insert a rubber washer, or use Teflon tape on threads. Water does not flow when shower valve is turned on. Turn water source on. Check that knob is installed tight. Base teeters from side to side. Move to a flat level surface. Water pressure is very low. Increase pressure at water source valve. Extension feels loose. Tighten the base attachment screws. If above trouble shooting guide is ineffective, call our technical service department at 1-888-545-1424
P.O. BOX 5128 CONCORD, CA 94524 TOLL FREE 888-545-1424 TM www.tahitishower.com SIERRA STERLING 2007 ST-1001 PRINTED IN CHINA