Basic DBE Easy installation in less than two hours Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Basic DBE Dimensions Prouct coe: BASW B h H h 70 Connections L 155 Stanar connection 20 (bottom left) or 70 (bottom right) 65 h H h 70 L 70 L 155 70 The stanar casings conceal the valves B B B 65 B h H h B 70 h h H h H h B h H h L 70 h H h L 15570 65 Type A B h (min) 11 29 119 500 L 16 53 169 80 120 1555 21 79 219 10 L 155 65 65 Top valve connection 65 155 65 30 (top left) or 60 (top right) Dimensions in mm Jaga Comap valve to the wall Jaga Pro valve to the wall Jaga valve to the wall 2 25 25 25 25 25 72 72 72 72 72 38 12 38 3812 A 2 12 72 A 2 38 12 38 38 12 12 A A 2 2 A A 2 2 27 27 27 27 27 27 Jaga Comap valve to the floor Jaga Pro valve to the floor Jaga valve to the floor 75 75 75 85 85 85 60 60 60 2 25 25 38 1238 38 12 12 27 27 27 75 75 85 85 75 85 60 60 60 25 25 38 12 25 38 12 27 27 38 12 27 Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Options Non-stanar height an length Available upon request Thermostatic valve set Available upon request Top valve Inclues: Jaga thermostatic hea an sleeve couplings Orering coe for top left: a 30 to prouct coe Orering coe for top right: a 60 to prouct coe Orering coe: 90.13001 Pre-mounte fixing system Jaga Thermostatic hea The heat exchanger an brackets provie pre-mounte, saving installation time Orering coe: 5125.020 Liqui fille with antifreeze protection to 6 C Minimum an maximum temperature control (5-26 C) by ring-system Screw connection M30x1.5 Orering coe: 90.110 U-channel recess The case can be mounte or emounte without removing the thermostatic valve hea Orering coe for right han connection: a the suffix SR to the prouct coe Orering coe for the left han connection: a the suffix SL to the prouct coe No surcharge Brush Offers easy cleaning to the unersie of the Low-H20 heat exchanger without the nee of etaching the casing Orering coe: 90.001 Deco thermostatic hea Liqui fille Anti-freeze protection 8 C an regulable from 10 up to 27 C (Jaga Comap: 6 up to 30 C) Maximum temperature control by pin on insie (Jaga Comap: ring-system) Screw connection M30x1.5 Colour Silver 90.1119 Chrome / 90.1110 Chrome 90.1111 Pencil-proof grille Base grille Prevents smaller objects or waste falling within the casing Lacquere in the same colour as the casing Closes the bottom en of the casing Lacquere in the same colour as the casing Orering coe: 562.000 Orering coe: 561.000 Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Outputs Output calculate in accorance with EN2, at a water temperature of 75/65 C an a room temperature of 20 C (ΔT=). Basic DBE contract raiator - Type 11 Outputs in watts, in accorance with EN2 coe height length type colour moel DBE Orer coe: BASW 032 060 11 133 05 DBE (Example orer coe shown is for a 320mm high raiator, 600mm long, type 11) 320 H L 600 700 800 900 1000 1100 1200 100 1600 1800 2000 200 2800 20 520 620 720 920 Supplie as Stanar Colour 133, 101 or 001 Twin Low-H20 heat exchanger DBE set with 12 V DC power supply PCB control unit an controls, an 1 to 6 DBE unit(s) Brackets provie with pre-installe lock Tools require to remove casing Wall brackets One piece casing Fixing kit Extene air vent 1/8 Drain plug 1/2 All imensions are shown in millimetres Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Outputs Output calculate in accorance with EN2, at a water temperature of 75/65 C an a room temperature of 20 C (ΔT=). Basic DBE contract raiator - Type 16 Outputs in watts, in accorance with EN2 coe height length type colour moel DBE Orer coe: BASW 032 060 16 133 05 DBE (Example orer coe shown is for a 320mm high raiator, 600mm long, type 16) 320 H L 600 700 800 900 1000 1100 1200 100 1600 1800 2000 200 2800 20 520 620 720 920 Supplie as Stanar Colour 133, 101 or 001 Twin Low-H20 heat exchanger DBE set with 12 V DC power supply PCB control unit an controls, an 1 to 6 DBE unit(s) Brackets provie with pre-installe lock Tools require to remove casing Wall brackets One piece casing Fixing kit Extene air vent 1/8 Drain plug 1/2 All imensions are shown in millimetres Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Outputs Output calculate in accorance with EN2, at a water temperature of 75/65 C an a room temperature of 20 C (ΔT=). Basic DBE contract raiator - Type 21 Outputs in watts, in accorance with EN2 coe height length type colour moel DBE Orer coe: BASW 032 060 21 133 05 DBE (Example orer coe shown is for a 320mm high raiator, 600mm long, type 21) 320 H L 600 700 800 900 1000 1100 1200 100 1600 1800 2000 200 2800 20 520 620 720 920 Supplie as Stanar Colour 133, 101 or 001 Twin Low-H20 heat exchanger DBE set with 12 V DC power supply PCB control unit an controls, an 1 to 6 DBE unit(s) Brackets provie with pre-installe lock Tools require to remove casing Wall brackets One piece casing Fixing kit Extene air vent 1/8 Drain plug 1/2 All imensions are shown in millimetres Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Connection Sets Set 26 Jaga Comap valve COLO.CP2.DW... Universal valve set for connection to the wall or to the floor Kv max. 0.6 Thermostatic hea of choice Thermostatic hea / Thermostatic heas DW COLO.CP2.DC... COLO.CP2.JA... COLO.CP2.JC... The orer coe of the connection set will be complete with the sleeve coupling coe Set 11 Jaga Pro valve Connection to the wall - bottom of casing Jaga Comap thermostatic valve Sleeve couplings Eurocone 3/ Kv max. 0.6 Chrome/ White DC Chrome COLO.PW2.DW.3... Thermostatic hea / Thermostatic hea of choice JA COLO.PW2.DC.3... COLO.PW2.JA.3... Jaga Pro valve COLO.PW2.JC.3... Sleeve couplings M2 White 2 curves to the wall JC Set 12 Jaga Pro valve Connection to the floor Kv max. 0.6 Silver COLO.PF2.DW.3... Thermostatic hea / Thermostatic hea of choice RM COLO.PF2.DC.3... Jaga Pro valve COLO.PF2.JA.3... COLO.PF2.JC.3... Sleeve couplings M2 Remote Controlle Set 21 Jaga valve DS Connection to the wall - Not for Basic Type 06 Kv max. 0.6 COLO.JW2.DW.2... Thermostatic hea / Jaga thermostatic valve Sleeve couplings M2 Chrome/ remote sensor COLO.JW2.DC.2... COLO.JW2.JA.2... COLO.JW2.JC.2... Angle lockshiel Thermostatic hea of choice Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Set 22 Jaga valve The orer coe of the connection set will be complete with the sleeve coupling coe COLO.JF2.DW.2... COLO.JF2.DC.2... COLO.JF2.JA.2... COLO.JF2.JC.2... Connection to the floor Kv max. 0.6 Thermostatic hea / Jaga thermostatic valve Thermostatic hea of choice Straight lockshiel Sleeve couplings M2 Thermostatic heas DW Set 23 Jaga valve Chrome/ White Connection to the floor Kv max. 0.6 DC COLO.JW3.DW.2... COLO.JW3.DC.2... Thermostatic hea / Jaga thermostatic valve Extension pipe Thermostatic hea of choice Chrome COLO.JW3.JA.2... COLO.JW3.JC.2... Sleeve couplings M2 JA H-piece angle Set 2 Jaga valve White Connection to the floor Kv max. 0.6 JC COLO.JF3.DW.2... COLO.JF3.DC.2... Thermostatic hea / Jaga thermostatic valve Extension pipe Thermostatic hea of choice Silver COLO.JF3.JA.2... H-piece straight RM COLO.JF3.JC.2... Sleeve couplings M2 Set 25 Jaga Type 6 valve Remote Controlle COLO.SW2.DW.3... Connection to the wall within the casing - for F Type 06 Kv max. 0.6 Jaga Type 6 thermostatic valve Thermostatic hea Sleeve couplings M2 / DS COLO.SW2.DC.3... COLO.SW2.JA.3... Thermostatic hea of choice Chrome/ remote sensor COLO.SW2.JC.3... Angle lockshiel Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Sleeve Couplings Inclue in the price of the connection sets Pro Key Tool for easy mounting of the Jaga Pro valve. For Jaga Comap valve - Eurocone 3/ 90.1120 For flexible steel or copper tube Tube Ø 112 12/1 11 1/1 115/1 116 16/1 118 18/1 3/ For synthetic or RPE/ALU tube Tube Ø 612 12/2 61 1/2 616 16/2 617 17/2 618 18/2 615/2.5 M 2 3/ For tube 12/2 only 619 16/1.5 620 20/2 For Jaga valve - M2 For flexible steel or copper tube For synthetic tube Tube Ø Tube Ø 110 10/1 112 12/1 11 1/1 115/1 116 16/1 118 18/1 1/2 1/2 For tube 15/1 only 1/2 For tube 18/1 only 212 12/2 21 1/2 219 16/1.5 216 16/2 217 17/2 218 18/2 1/2 For RPE/ALU tube Steel tube for CH 1/2 Tube Ø 1/2 1/2 Tube Ø 1 1/2 6 16/2 3 3/8 326 16/2.2 8 18/2 Short Coupling - for Connection to the wall For flexible steel or copper tube Ø 15mm Tube Ø 125/1 Complete orering coe with sleeve couplings accoring to the material use an iameter of the tube. The correct type of sleeve coupling is etermine by the orering coe of the connection set Example: COLO. PW2.DW. 32. (insert relevant coe from above) 1/2" 1/2 Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Correction factors Average correction factors accoring to EN2-75/65/20 C for Comfort an Boost moe Tv Tl Tr > 20 25 30 35 0 5 55 60 65 70 75 80 85 90 20 0.70 0.75 0.80 0.85 0.90 0.9.00 1.0.10 1.1.20 1.2.30 1.35 2 0.62 0.67 0.72 0.77 0.82 0.87 0.92 0.97 1.02 1.07 1.12 1.17 1.22 1.32 85 20 0.65 0.70 0.75 0.80 0.85 0.90 0.9.00 1.0.10 1.1.20 1.25 2 0.57 0.62 0.67 0.72 0.77 0.82 0.87 0.92 0.97 1.02 1.07 1.12 1.17 80 20 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.9.00 1.0.10 1.15 2 0.52 0.57 0.62 0.67 0.72 0.77 0.82 0.87 0.92 0.97 1.02 1.07 75 20 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.9.00 1.05 2 0.7 0.52 0.57 0.62 0.67 0.72 0.77 0.82 0.87 0.92 0.95 70 20 0. 0.55 0.60 0.65 0.70 0.75 0.80 0.85 0.90 0.95 2 0.2 0.7 0.52 0.57 0.62 0.67 0.72 0.77 0.82 0.87 65 20 0.5 0. 0.55 0.60 0.65 0.70 0.75 0.80 0.85 2 0.37 0.2 0.7 0.52 0.57 0.62 0.67 0.72 0.77 60 20 0.0 0.5 0. 0.55 0.60 0.65 0.70 0.75 2 0.32 0.37 0.2 0.7 0.52 0.57 0.62 0.67 55 20 0.35 0.0 0.5 0. 0.55 0.60 0.65 2 0.27 0.32 0.37 0.2 0.7 0.52 0.57 20 0.30 0.35 0.0 0.5 0. 0.55 2 0.22 0.27 0.32 0.37 0.2 0.7 5 20 0.25 0.30 0.35 0.0 0.5 2 0.17 0.22 0.27 0.32 0.37 0 20 0.20 0.25 0.30 0.35 2 0.12 0.17 0.22 0.27 35 20 0.15 0.20 0.25 2 0.07 0.12 0.17 30 20 0.10 0.15 2 0.02 0.07 KEY Tv = flow temperature Tr = return temperature Tl = esire air temperature The inicate outputs with T c are the exact outputs an are calculate in accorance with EN2. An average correction factor is given in this table for outputs at other T an is applicable for all imensions. How to choose the right raiator? Rapi estimation of heat losses Calculate the volume of the room (L x W x H) an multiply this by the Watts/m³ figure given in the table below. Choose accoring to the level of insulation an the esire room temperature. Insulation 20 2 excellent 5 55 goo 65 75 average 85 95 poor 100 115 Require output in Watts/m³ Example Use the table to etermine the relevant correction factor with a water temperature of 60/5 c with a room temperature of 20 C. The correction factor = 0.65 Require output 1000 watts : 1000 ivie by 0.65 = 1538 watts therefore search in this leaflet s stanar output table for a prouct with an output of at least 1538 watts. Alternatively use the Raiator Finer search function on www.jaga.co.uk to ientify all Jaga heating proucts with this require output. Output calculate in accorance with EN2, at a water temperature of 75/65 C an a room temperature of 20 C (ΔT=). Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Acoustic Data Soun pressure an correction factors Combine soun level of multiple DBE units Type b(a) Comfort Boost 11 29 35 16 27 Several appliances with an equal soun level in a room Number b(a) 2 +3.0 3 +.8 Correction b(a) P2 = P1 + 10 log n P1 = soun level one appliance P2 = soun level to be calculate n = number of appliances Through the DBE-communication software (DBED) it is possible to set up other activator spees. In this way you can obtain other outputs an soun pressures. For more information, contact Jaga. Increase of soun pressure B(A) 16 1 12 10 8 6 2 0 1 8 12 16 20 2 28 32 36 0 Number of fan moules For reference a typical conversation has a b level of 60, a motorbike is 105b an a rock concert 10b. Correction factor by room volume Volume (m3) 80 0 1-2.7 200 -.0 2 -.9 300-5.7 3-6. 00-7.0 0-8.0 600-8.8 Correction b(a) Equation for calculating soun pressure in other room sizes P2 = P1-10 log V2 V1 P1 = table of soun pressure P2 = soun level to be calculate V1 = size of room of reference (80 m³) V2 = other room size Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Prouct specification Basic DBE Material DBE technology Low-H2O heat exchanger is compose of roun, seamless circulation tubes mae of pure re copper, with pure aluminium fins an two brass collectors for left or right 1/2 same en connection Extene air vent 1/8 an rain plug 1/2 are inclue Pressure test: 20 bar Working pressure: 10 bar Brackets: senzimir, galvanize steel plate thickness 1mm, ark grey lacquere, with a maximum intermeiate istance of 1.05m Front panel: electrolytic, galvanize steel plate of 1.25mm thick Sie panels: electrolytic, galvanize steel plate of 1.25mm thick with hole for integrate Jaga valve, inclusive metallize cover plates for the unuse hole Inverse aluminium top grille coate in the same colour as the casing Strong an functional packaging, can be use as a protection cover uring construction works Colour Heat exchanger electrostaticaly lacquere with anthracite grey epoxypolyester RAL 702, gloss egree 70% The casing is lacquere in the colour (RAL 9010) / (RAL 9016) / sanblast grey metallic 001 / other (see colour chart). The coating is a scratch resistant epoxy-polyester power, spraye electrostatically an bake at a temperature of 200 C. UV resistant ue to ASTM G53 Prouct information The casing surface temperature remains safe to touch at all times Manufacturer: Jaga Type: Basic Outputs measure in accorance with EN2, at a water temperature of 75/65 C an a room temperature of 20 C (ΔT= C) Options Base grille or pencil grille Brush for easy cleaning of the unersie of the heat exchanger Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Jaga colour range Basic DBE RAL 9010 101 White 112 Bahama 122 Capri RAL 9016 133 Traffic White RAL 9001 102 Off- RAL 6009 113 English Green 123 Natural Special Colours RAL 7035 RAL 9005 RAL 03 RAL 7011 RAL 100 RAL 3000 103 Light Grey Black 105 Pergamon 106 Manhattan 108 Sapphire Blue 109 Dark Grey 110 Golen Yellow 111 Flaming Re RAL 18 RAL 8017 11 Whisper Rose 115 Turquoise 116 Bermua 117 Chocolate Brown RAL 15 RAL 008 118 Azure 119 Violet 120 Aegean 121 Calypso RAL 3003 RAL 6000 RAL 7016 12 Eelweis 125 Jasmine 126 Ruby Re 128 Classic White 129 Patina Green 130 Aloa Blue 1 Anthracite Grey 132 Sunrise 001 Sanblast Grey Metallic 002 Hammerstroke Silver/Black RAL 9006 003 Claret Metallic 00 Gol Structure 005 Smooth Grey Metallic 006 Aluminium 007 Anthracite Metallic 008 Anthracite Structure Jaga Heating Proucts (UK) Lt www.jaga.co.uk
Jaga Guarantee Information 1 The guarantee is vali only if the equipment is properly an correctly use, by its first owner an if installe in accorance with the norms an instructions as etaile in the instruction leaflet an current inustry stanar practices. 2 The guarantee only applies to the equipment an the spare parts supplie by Jaga. Jaga has the choice between repair an replacement of the equipment or the spare parts. If any moifications have been mae by Jaga to the stanar prouct esign, Jaga reserves the right to replace the guarantee equipment with equivalent proucts or spare parts. 3 The perio of guarantee is mentione in this certificate. The guarantee ecreases every year on a straight line basis by an equal percentage in orer to reach a zero guarantee at the en of the guarantee perio (e.g. for a perio of 10 years the annual ecrease of the guarantees 10% of the invoice value). Repaire or replace prouct is guarantee through to the en of the original guarantee perio. The guarantee is vali only on proucts isplaying the appropriate ientification information concerning prouct type an series. No guarantee is grante on equipment or spare parts lacking this information, on equipment where this information has been remove or altere, or on equipment that has been repaire or moifie by persons not authorise by Jaga to carry out this work. 5 The customer is responsible for any amage cause as a result of errors in installation or use of incorrect fittings, or for any amage cause by electrical connections, faulty or amage electrical installations or appliances, erroneous voltage or hyraulic pressure an all other errors not irectly relate to the prouct elivere by Jaga. The guarantee is also revoke when unsuitable parts or components are use. The guarantee for our heat exchangers is not vali if they are regularly raine, or if they are heate by means of inustrial water, steam or water saturate by excessive quantities of oxygen. The quality of the system ater has to be in accorance with the VDI 2035-2 irectives. The guarantee is also not applicable if the heat exchangers are place in unsuitable atmospheric surrounings, such as but not exclusively ammonia, caustic substances etc. 6 This guarantee exclues amage ue to incorrect hanling an/or use of the equipment, or ue to formation of lime eposits, incorrect use of the safety valve, or to all equipment that is incorporate into the builing in a way that means it cannot be accesse normally. 7 Any work unertaken or prouct supplie as a result of a guarantee claim that proves not to be vali will be charge for. Prouct supplie will be invoice at the customer s stanar purchasing terms, an labour will be charge at per hour with a minimum labour charge of 200. 8 The guarantee perio starts from the ate of the invoice for supply of the proucts covere by the guarantee. If the invoice is not available, the ate of prouction will be use base on the prouct ID number/series. 9 Only the courts of juicial istrict Hasselt (Belgium) are authorise to eal with isputes arising from this guarantee. It will apply Belgian law even when sales involve are subjects of EU member states as well as non-eu member countries. Heat exchanger Casings an components Valves for Low-H2O heat exchangers Jaga Heating Proucts (UK) Lt www.jaga.co.uk