Ref. Certif. No. DK-29983-UL IEC SYSTEM FOR MUTUAL RECOGNITION OF TEST CERTIFICATES FOR ELECTRICAL EQUIPMENT (IECEE) CB SCHEME SYSTEME CEI D'ACCEPTATION MUTUELLE DE CERTIFICATS D'ESSAIS DES EQUIPEMENTS ELECTRIQUES (IECEE) METHODE OC CB TEST CERTIFICATE Product Produit Name and address of the applicant Nom et adresse du demandeur Name and address of the manufacturer Nom et adresse du fabricant Name and address of the factory Nom et adresse de l'usine Note: When more than one factory, please report on page 2 Note: Lorsque il y plus d'une usine, veuillez utiliser la 2 ème page Ratings and principal characteristics Valeurs nominales et caractéristiques principales Trademark (if any) Marque de fabrique (si elle existe) CERTIFICAT D'ESSAI OC DC/DC Converter ERICSSON AB FAROGATAN 6 STOCKHOLM, SE-164 80 Sweden ERICSSON AB FAROGATAN 6 STOCKHOLM, SE-164 80 Sweden SHANGHAI ERICSSON ELECTRONICS CO LTD 33 FUHUA RD JIADING DISTRICT SHANGHAI, 201818. China Additional Information on page 2 See Page 2 Ericsson Type of Manufacturer's Testing Laboratories used Type de programme du laboratoire d'essais constructeur Model / Type Ref. Ref. De type PKD 4118 SIOD, PKD 4118 SIODN, PKD 4210 SI, PKD 4218 SI, PKD 4218 SIN, PKD 4218 SIOA, See Page 2 Additional information (if necessary may also be reported on page 2) Les informations complémentaires (si nécessaire,, peuvent être indiqués sur la 2 ème page A sample of the product was tested and found to be in conformity with Un échantillon de ce produit a été essayé et a été considéré conforme à la As shown in the Test Report Ref. No. which forms part of this Certificate Comme indiqué dans le Rapport d'essais numéro de référence qui constitue partie de ce Certificat Additional Information on page 2 IEC 60950-1(ed.2), IEC 60950-1(ed.2);am1 E210157-A8-CB-3 issued on 2012-12-24 This CB Test Certificate is issued by the National Certification Body Ce Certificat d'essai OC est établi par l'organisme National de Certification Date: 2012-12-24 Signature: UL (US), 333 Pfingsten Rd IL 60062, Northbrook, USA UL (Demko), Borupvang 5A DK-2750 Ballerup, DENMARK UL (JP), Marunouchi Trust Tower Main Building 6F, 1-8-3 Marunouchi, Chiyoda-ku, Tokyo 100-0005, JAPAN UL (CA), 7 Underwriters Road, Toronto, M1R 3B4 Ontario, CANADA For full legal entity names see www.ul.com/ncbnames Jan-Erik Storgaard rd 1/2
Ref. Certif. No. DK-29983-UL Model Details: PKD 4118 SIOD,PKD 4118 SIODN,PKD 4210 SI,PKD 4218 SI,PKD 4218 SIN,PKD 4218 SIOA,PKD 4218 SIOAN,PKD 4218HE SI,PKD 4218L ASI,PKD 4218LE SI,PKD 4218N ASI,PKD 4319 SI,PKD 4319 SIN,PKD 4510 ASI,PKD 4510E SI,PKD 4511 ASI,PKD 4210 SIN,PKD 4311 SI,PKD 4311 SIN,PKD 4318G ASI,PKD 4318H ASI,PKD 4319 ASI where "SI" suffix for PKD-E series could be replaced by "SRI" or "SPBI" Ratings: Input: All models 36-75Vdc Output: 1. 3.3Vdc/26W, 2. 5.0Vdc/30W, 3. 1.5Vdc, 30W, 4. 1.8Vdc/36W, 5. 2.5Vdc/38W, 6. 2.5Vdc/30W, 7. 1.0Vdc/20W, 8. 1.2Vdc/24W, 9. 1.8Vdc/25W, 10. 1.5Vdc/21W, 11. 1.2Vdc/17W, 12. 3.3Vdc/50W, 13. 5Vdc/50W, 14. 1.2Vdc/24W, 15. 1.5Vdc/21W, 16. 3.3Vdc/50W No ratings are required on the product Additional Information: Model/Type reference: 1. PKD 4210 SI or SIN, 2. PKD 4311 SI or SIN, 3. PKD 4318H ASI, 4. PKD 4318G ASI, 5. PKD 4319 ASI, 6. PKD 4319 SI or SIN, 7. PKD 4218N ASI, 8. PKD 4218L ASI, 9. PKD 4218 SI or SIN, 10. PKD 4218 SIOA or SIOAN, 11. PKD 4118 SIOD or SIODN, 12. PKD 4510 ASI, 13. PKD 4511 ASI, 14. PKD 4218LE SI, 15. PKD 4218HE SI, 16. PKD 4510E SI Additionally evaluated to EN 60950-1:2006/A11:2009/A1:2010/A12:2011; National Differences specified in the CB Test Report. Additional information (if necessary) Information complémentaire (si nécessaire) UL (US), 333 Pfingsten Rd IL 60062, Northbrook, USA UL (Demko), Borupvang 5A DK-2750 Ballerup, DENMARK UL (JP), Marunouchi Trust Tower Main Building 6F, 1-8-3 Marunouchi, Chiyoda-ku, Tokyo 100-0005, JAPAN UL (CA), 7 Underwriters Road, Toronto, M1R 3B4 Ontario, CANADA For full legal entity names see www.ul.com/ncbnames Date: 2012-12-24 Signature: Jan-Erik Storgaard 2/2
Issue Date: 2012-12-24 Page 1 of 54 Report Reference # E210157-A8-CB-3 Test Report issued under the responsibility of: Report Reference No... : TEST REPORT IEC 60950-1 Information technology equipment - Safety - Part 1: General requirements E210157-A8-CB-3 Date of issue... : 2012-12-24 Total number of pages... : 54 CB Testing Laboratory... : Address... : Applicant's name... : Address... : Test specification: UL International Polska Sp. z o.o. Aleja Krakowska 81, 05-090 Sekocin Nowy, Poland ERICSSON AB FAROGATAN 6 SE-164 80 STOCKHOLM SWEDEN Standard... : IEC 60950-1:2005 (2nd Edition); Am 1:2009 Test procedure... : Non-standard test method... : Test Report Form No.... : Test Report Form originator... : CB Scheme N/A IEC60950_1B SGS Fimko Ltd Master TRF... : 2010-04 Copyright 2010 IEC System for Conformity Testing and Certification of Electrical Equipment (IECEE), Geneva, Switzerland. All rights reserved. This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting from the reader's interpretation of the reproduced material due to its placement and context. If this test Report is used by non-iecee members, the IECEE/IEC logo and the reference to the CB Scheme procedure shall be removed. This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
Issue Date: 2012-12-24 Page 2 of 54 Report Reference # E210157-A8-CB-3 Test item description... : Trade Mark... : DC/DC Converter Ericsson Manufacturer... : Model/Type reference... : Ratings... : ERICSSON AB FAROGATAN 6 SE-164 80 STOCKHOLM SWEDEN 1. PKD 4210 SI or SIN, 2. PKD 4311 SI or SIN, 3. PKD 4318H ASI, 4. PKD 4318G ASI, 5. PKD 4319 ASI, 6. PKD 4319 SI or SIN, 7. PKD 4218N ASI, 8. PKD 4218L ASI, 9. PKD 4218 SI or SIN, 10. PKD 4218 SIOA or SIOAN, 11. PKD 4118 SIOD or SIODN, 12. PKD 4510 ASI, 13. PKD 4511 ASI, 14. PKD 4218LE SI, 15. PKD 4218HE SI, 16. PKD 4510E SI, where "SI" suffix for PKD-E series could be replaced by "SRI" or "SPBI", Input: All models 36-75Vdc Output: 1. 3.3Vdc/26W, 2. 5.0Vdc/30W, 3. 1.5Vdc, 30W, 4. 1.8Vdc/36W, 5. 2.5Vdc/38W, 6. 2.5Vdc/30W, 7. 1.0Vdc/20W, 8. 1.2Vdc/24W, 9. 1.8Vdc/25W, 10. 1.5Vdc/21W, 11. 1.2Vdc/17W, 12. 3.3Vdc/50W, 13. 5Vdc/50W, 14. 1.2Vdc/24W, 15. 1.5Vdc/21W, 16. 3.3Vdc/50W No ratings are required on the product
Issue Date: 2012-12-24 Page 3 of 54 Report Reference # E210157-A8-CB-3 Testing procedure and testing location: [x] CB Testing Laboratory Testing location / address... : UL International Polska Sp. z o.o. Aleja Krakowska 81, 05-090 Sekocin Nowy, Poland [ ] Associated CB Test Laboratory Testing location / address... : Tested by (name + signature)... : Hubert Koszewski Approved by (name + signature)... : Michal Siudowski [ ] Testing Procedure: TMP Tested by (name + signature)... : Approved by (+ signature)... : Testing location / address... : [ ] Testing Procedure: WMT Tested by (name + signature)... : Witnessed by (+ signature)... : Approved by (+ signature)... : Testing location / address... : [ ] Testing Procedure: SMT Tested by (name + signature)... : Approved by (+ signature)... : Supervised by (+ signature)... : Testing location / address... : [ ] Testing Procedure: RMT Tested by (name + signature)... : Approved by (+ signature)... : Supervised by (+ signature)... : Testing location / address... : List of Attachments National Differences (41 pages) Enclosures (17 pages) Summary of Testing: All Applicable tests according to the referenced standard(s) have been carried out Summary of Compliance with National Differences: Countries outside the CB Scheme membership may also accept this report. List of countries addressed: AT, BE, BG, BY, CA, CH, CZ, DE, DK, ES, EU, FI, FR, GB, GR, HU, IE, IL, IT, JP, KR, NL, NO, PL, PT, RO, SE, SG, SI, SK, UA, US
Issue Date: 2012-12-24 Page 4 of 54 Report Reference # E210157-A8-CB-3 The product fulfills the requirements of: EN 60950-1:2006 + A1:2010 + A11:2009 + A12:2011
Issue Date: 2012-12-24 Page 5 of 54 Report Reference # E210157-A8-CB-3 Copy of Marking Plate The artwork below may be only a draft. The use of certification marks on a product must be authorized by the respective NCBs that own these marks.
Issue Date: 2012-12-24 Page 6 of 54 Report Reference # E210157-A8-CB-3 Test item particulars : Equipment mobility...: Connection to the mains...: Operating condition...: Access location...: Over voltage category (OVC)...: Mains supply tolerance (%) or absolute mains supply values...: Tested for IT power systems...: IT testing, phase-phase voltage (V)...: - Class of equipment...: Considered current rating of protective device as part of the building installation (A)...: for building-in No direct connection to mains continuous No operator access permitted. Intended for building -in OVC II N/A Pollution degree (PD)...: PD 2 IP protection class...: No Special Application to be determined in end product IP X0 Altitude of operation (m)...: 2000 Altitude of test laboratory (m)...: 130 Mass of equipment (kg)...: <0.5 Possible test case verdicts: - test case does not apply to the test object... : N / A - test object does meet the requirement... : P(Pass) - test object does not meet the requirement... : F(Fail) Testing: Date(s) of receipt of test item...: 2007-06-25 Date(s) of Performance of tests...: 2010-11-22 General remarks: The test results presented in this report relate only to the object tested. This report shall not be reproduced, except in full, without the written approval of the testing laboratory. "(see Enclosure #)" refers to additional information appended to the report. "(see appended table)" refers to a table appended to the report. Throughout this report a point is used as the decimal separator. Manufacturer's Declaration per Sub Clause 6.25 of IECEE 02: The application for obtaining a CB Test Certificate includes more than one factory and a declaration form the Manufacturer stating that the sample(s) submitted for evaluation is (are) representative of the products from each factory has been provided... Not Applicable When differences exist, they shall be identified in the General Product Information section. Name and address of Factory(ies): SHANGHAI ERICSSON ELECTRONICS CO LTD 33 FUHUA RD JIADING DISTRICT
Issue Date: 2012-12-24 Page 7 of 54 Report Reference # E210157-A8-CB-3 SHANGHAI 201818 CHINA GENERAL PRODUCT INFORMATION: Report Summary All applicable tests according to the referenced standard(s) have been carried out. Product Description USR/CNR The products covered by this report are dc-to-dc converter switch mode power supplies, Models PKD 4xxx. May be followed by suffix ASI, SI, SIN, SIOA, SIOAN, SIOD or SIODN. They are provided with terminal pins for connection to their nominal rated dc source of supply and output connections. Model Differences ASI = Surface-mount, Insulated, Selectable Negative or Positive remote control logic. SI = Surface-mount, Insulated, Positive remote control. SIN = Surface-mount, Insulated, Negative remote control. SIOA = Surface-mount, Insulated, Optional output 1.5V (A), Positive remote control. SIOAN = Surface-mount, Insulated, Optional output 1.5V (A), Negative remote control. SIOD = Surface-mount, Insulated, Optional output 1.2V (D), Positive remote control. SIODN = Surface-mount, Insulated, Optional output 1.2V (D), Negative remote control. L and H = different output voltages (1.2V and 1.5V), E = the new series (PKD-E) The only difference between an old PKD series and a new PKD-E series schematic diagram is the component numbers and the layout. PKD-E series and the PKD series have the same electrical rating and foot print, the difference is mechanical: PKD is build on a ceramic board with all components on the pin side and a lead frame welded on top, PKD-E is build on a fiber glass board with all components on the top side and it has no pins. For PKD-E models suffix SI indicates surface-mount, Insulated, Selectable Negative or Positive remote control logic and SRI suffix indicates the same suited for leaded soldering, suffix SPBI indicates use of solder paste with lead (Pb). Additional Information The label is a draft of an artwork for marking plate pending approval by National Certification Bodies and it shall not be affixed to products prior to such an approval. E210157-A8-CB-3-Reissue (12CA68488) This report is a reissue of CBTR Ref. No.: E210157-A8-CB-2, CB Test Certificate Ref. No. DK-21050 due to standard upgrade to IEC 60950-1 2 Edition + Amenmend 1 and EN 60950-1:2006 +A1:2010 +A11:2009 +A12:2011. Based on the previously conducted testing and the review of product technical documentation including photos, schematics, wiring diagrams and similar, has been determined that the product continues to comply with the standard No tests conducted under this investigation due to reissue of CB Test Report Ref. No. E210157-A8-CB-2. All required tests were carried out under the original investigation
Issue Date: 2012-12-24 Page 8 of 54 Report Reference # E210157-A8-CB-3 This test report should be read in conjunction with the original report number: - E210157-A8-CB-1 issued 2005-05-09 with CB Cert. No. DK-8744 issued 2005-05-18. - E210157-A8-CB-1 with Amendment 1 issued 2007-09-26 with CB Cert. No. DK-8744-A1 issued 2007-10- 01. Testing was not considered necessary based on review of schematics, construction and component specifications. This report has been re-issued, due to: - The standard has been upgraded to IEC 60950-1 2nd Edition. - CBTL has been changed from UL Demko to UL Poland. - Applicant & Manufacture changed from ERICSSON POWER MODULES AB / LM ERICSSONS VAG 30, SE-126 25 STOCKHOLM SWEDEN to ERICSSON AB / ISAFJORDSGATAN 16B, STOCKHOLM SE-164 80, SWEDEN - List of factories has been updated. Factory name changed from SHANGHAI ERICSSON SIMTEK ELECTRONICS CO LTD to SHANGHAI ERICSSON ELECTRONICS CO LTD. Factory location 'PROXY ELECTRONICS AB' has been deleted. Technical Considerations The product was investigated to the following additional standards: EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011 (which includes all European national differences, including those specified in this test report). The transformer in the converter is not relied on for providing any insulation. It provides Functional insulation only. -- Output voltages remain within SELV limits, even with internally generated non-selv voltages. This was demonstrated by performing Abnormal Tests including single component failure and functional insulation bypass with various grounding conditions, and with the input and output floating. In all cases the output voltage did not exceed SELV. -- All models are evaluated and tested for use at altitude up to 5 000 m based on consideration that FUNCTIONAL INSULATION is employed in te product and tested by method 5.3.4 c). -- The product was submitted and evaluated for use at the maximum ambient temperature (Tma) permitted by the manufacturer s specification of: Maximum Case Temperature of 90 C -- Engineering Conditions of Acceptability When installed in an end-product, consideration must be given to the following: These components have been evaluated for FUNCTIONAL INSULATION only between input-output. -- When the DC-DC converter is supplied by ELV and SELV respectively, the following is considered: a) when the input comply with ELV the output of the DC/DC converter may be considered ELV; b) when the input comply with SELV, the output of the DC/DC converter remains at SELV under normal and abnormal operation condition. -- For cases when the supply voltage is higher than 60Vdc up to and including 75Vdc the following must be adhered: The input source to the DC/DC Converter must:, a) Be separated from primary circuit by DOUBLE/REINFORCED INSULATION (SELV or TNV-2 circuit), or, b) Be separated from primary circuit and earth by minimum BASIC INSULATION and the SELV circuits reliably connected to main earth terminal. -- Output voltages remain within SELV limits, even if the input supply voltage is up to 75Vdc and considering the source is centralized d.c. power system (DC mains voltage) treated as TNV-2 circuit
Issue Date: 2012-12-24 Page 9 of 54 Report Reference # E210157-A8-CB-3 (> 60 Vdc up to and including 80 Vdc). This has been confirmed by evaluation per sub-clause 2.2.4, sub-clause 2.3.2 and 5.3.4 and demonstrated by e.g. fault condition testing, where the functional insulation barriers have been short circuited and by electric strength test conducted across insulation. -- The power supply shall be installed in compliance with the enclosure, mounting, spacing, casualty, and segregation requirement of the ultimate application. -- The following secondary output circuits are at non-hazardous energy levels: All Outputs -- The power supply terminals and/or connectors are: Suitable for factory wiring only -- The maximum investigated branch circuit rating is: 15 A external fuse was used during the tests. -- The investigated Pollution Degree is: 2 -- The following end-product enclosures are required: Mechanical, Fire -- The following components require special consideration during end-product Thermal (Heating) tests due to the indicated maximum temperature measurements during component-level testing: Transformer M1(99.2 C) -- The end-product Electric Strength Test is to be based upon a maximum working voltage of: 101.9V peak, 42.2Vrms -- The DC/DC converter shall be protected by a 15 A time lag fuse in end-product. -- Models PKD series listed in this report were tested to confirm that under normal and single fault conditions the output operates within SELV limits (in accordance with sc 2.2.4.) When these converters are supplied by an ELV circuit AND the output is connected to main protective earthing, the functional insulation provided in the DC-DC converter is sufficient insulation. -- The following Production-Line tests are conducted for this product: Electric Strength for models with base plate. -- The following secondary output circuits are SELV: All outputs -- Abbreviations used in the report: - normal condition... N.C. - single fault condition...s.f.c - operational insulation... OP - basic insulation...bi - basic insulation between parts of opposite - supplementary insulation...si polarity: BOP - double insulation... DI - reinforced insulation...ri Indicate used abbreviations (if any)