DET NORSKE VERITAS CERTIFICATE OF CONFORMITY Certificate No. DNV-2009-OSL-ALARM-55363 This Certificate consists of 5 pages This is to certify that the product PIR / DUAL TECHNOLOGY DETECTORS with name type designations iwise 815DTG3, iwise 825DTG3, iwise 810DTGL, iwise 815DTGL, 825DTGL, iwise 800QG3, iwise 815DTBG3, iwise 825DTBG3, iwise 800QBG3, Lunar 150DTG3 (as detailed overleaf) manufactured by RISCO Ltd. Rishon Letzion, Israel have been assessed with respect to EN 50131 including relevant underlying normative references, and found to comply with the applicable requirements. Further details are given overleaf Place and date: Høvik, 2009-06-22 for DET NORSKE VERITAS CERTIFICATION AS Norway This Certificate is valid until: 2014-06-22 PROD 002 Marianne Spæren Certification Manager (ZNWNO416) Stian Mong Technical Reviewer Notice: The certificate is subject to terms and conditions overleaf. Any significant changes in design or construction may render this certificate invalid. If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of Det Norske Veritas, then Det Norske Veritas shall pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 300.000. In this provision Det Norske Veritas shall mean the Foundation Det Norske Veritas as well as all its subsidiaries, directors, officers, employees, agents and any other acting on behalf of Det Norske Veritas. Page 1 of 5
Certificate history Revision Description Issue Date 0 Original Certificate 2009-06-22 Products covered by this Certificate Model name P/N Description iwise 815DTG3 iwise 825DTG3 RK815DTG300B RK825DTG300B Dual Tech Anti Mask 15m Grade 3 detector Dual Tech Anti Mask 25m Grade 3 detector PCB Schematic N D 17 N D 17 iwise 810DTGL RK810DTGL00A Dual Tech 10m Grade 2 detector N D 02 iwise 815DTGL RK815DTGL00A Dual Tech 15m Grade 2 detector N E 02 iwise 825DTGL RK825DTGL00A Dual Tech 25m Grade 2 detector N D 02 iwise 800QG3 RK800Q0G300B iwise Quad Grade 3 detector N D 08 iwise 815DTBG3 RK815DTB000A iwise DT 15m Grade 3 BUS detector E F 17 iwise 825DTBG3 RK825DTB000A iwise DT 25m Grade 3 BUS detector E F 17 iwise 800QBG3 RK800Q0B000A iwisde QUAD G3 BUS detector N F 23 LuNAR 150DTG3 RK150DTG300B Lunar DT Grade 3 ceiling detector G E 17 SW Page 2 of 5
Applications/Limitations Product Description Security Grade Environmental Class iwise 815DTG3 3 II iwise 825DTG3 3 II iwise 810DTGL 2 II iwise 815DTGL 2 II iwise 825DTGL 2 II iwise 800Q 3 II iwise 815DTBG3 3 II iwise 825DTBG3 3 II iwise 800QBG3 3 II LuNAR 150DTG3 3 II Remarks SMD - variant of previously approved SMD - variant of previously approved Variant of the SMD G3 (same PCB, some Variant of the SMD G3 (same PCB, some Variant of the SMD G3 (same PCB, some SMD - variant of previously approved Variant of SMD G3, plus BUS support Variant of SMD G3, plus BUS support Variant of SMD G3, plus BUS support SMD - variant of previously approved Page 3 of 5
Applied Standards Product Description Applied Standards ALL UNITS EN 61000-6-3:2007, EN 50130-4:1995+A1(98)+A2(03), EN 50130-5:1998, EN 50131-1:2006 iwise 815DTG3 EN 50131-2-4:2008 iwise 825DTG3 EN 50131-2-4:2008 iwise 810DTGL EN 50131-2-4:2008 iwise 815DTGL EN 50131-2-4:2008 iwise 825DTGL EN 50131-2-4:2008 iwise 800Q EN 50131-2-2:2008 iwise 815DTBG3 EN 50131-2-2:2008 iwise 825DTBG3 EN 50131-2-4:2008 iwise 800QBG3 EN 50131-2-4:2008 LuNAR 150DTG3 EN 50131-2-4:2008 Documents reviewed Name Description E90190.pdf Test report EN 61000-6-3, EN 50130-4 E86310.01.pdf Test report EN 61000-6-3, EN 50130-4 T86330,01 Risco Env_with Shock.pdf Test report EN 50130-5 T86330,01 Risco Func.pdf Test report EN 50131-1, EN 50131-2-2, EN 50131-2-4 Page 4 of 5
Terms and conditions The certificate is subject to the following terms and conditions: Any producer (see 2001/95/EC for a precise definition) is liable for damage caused by a defect in his products, in accordance with directive 85/374/EEC, as amended, concerning liability of defective products. The Certificate is only valid for the products listed above The Certificate is concerned with the design of the product, only The following may render this Certificate invalid: Changes in the design or construction of the products Changes or amendments to the referenced standards END OF CERTIFICATE Page 5 of 5