GB IE User Manual WR10-CP-LED 10 W Art.-No.: 1 20 02 10020 WR20-CP-LED 20 W Art.-No.: 1 20 02 10022 WR30-CP-LED 30 W Art.-No.: 1 20 02 10024 WR10-CP-LED-BW 10 W Art.-No.: 1 20 02 10021 WR20-CP-LED-BW 20 W Art.-No.: 1 20 02 10023 WR30-CP-LED-BW 30 W Art.-No.: 1 20 02 10025 WR90-LED 90 LEDs Art.-No.: 1 20 02 10026 WR120-LED 120 LEDs Art.-No.: 1 20 02 10028 WR90-LED-BW 90 LEDs Art.-No.: 1 20 02 10027 WR120-LED-BW 120 LEDs Art.-No.: 1 20 02 10029
GB IE Table of Contents Introduction and intended use 1 Items supplied 1 Technical Data 2 Safety notes 2 Product description 3 Start up and use Wall mounting Connecting LED spotlight 4 4 4 Function Motion Detector 5 Cleaning 6 Malfunktion list 6 Warranty and service 6 Disposal 6 Conformity and manufacturer Introduction and Intended Use Please read these instructions thoroughly. They are a component of the product you have purchased and contain important information regarding its use. Always follow the safety advice. Should you have questions or are uncertain as to the use of the LED wall spotlight, please contact your service point. Hereinafter, the LED wall spotlight is referred to as LED spotlight. The LED spotlight is suitable for permanent mounting on walls of private, as well as commercial areas. Due to its easy installation, the LED spotlight is ideal for lighting property and business premises. Items supplied After unpacking, please check the items supplied for completeness, as well as faultless condition of the product. 1 x LED wall spotlight 1 x Usage instructions 1 x Mounting bracket -1-
Technical data Nominal voltage Current rating 220-240 V AC 50 Hz 16 A Protection class IP 54 IP 44 Output 10 W / 20 W / 30 W 5 W (90 LEDs) 7 W (120 LEDs) 10 W / 20 W / 30 W 5 W (90 LEDs) 7 W (120 LEDs) Energy efficiency class A Light colour 6400 K Motion Detector Coverage angle - - - - 120 Coverage area - - - - max. 9 m Time setting - - - - 5 Sek. bis 8 Min. Dimensions (L x W x H) Weight ca. 22,5 x 14,0 x 10,5 cm ca. 700 g ca. 22,5 x 14,5 x 17,5 cm ca. 780 g ca. 22,5 x 14,0 x 10,5 cm ca. 700 g ca. 22,5 x 14,5 x 17,5 cm ca. 780 g Safety notes Please observe the following safety warnings at all times in order to prevent risks of injury to people or property damage due to incorrect usage. Damages caused due to not observing the usage instructions, especially the safety notes, void the warranty. We accept no liability for resulting property damage or personal injury, as well as consequential damages. -2-
Definition of the signal words and symbols: DANGER Extremely dangerous situation. If not observed, death or serious injury. NOTE What you need to observe. CAUTION Possibly dangerous situation. Low risk of injury to people. IMPORTANT Read the usage instructions carefully and retain these. Upon transmission of the product to third parties, please also provide the usage instructions. DANGER Extremely dangerous situation. If not observed, death or serious injury. Keep children away from packaging material (e.g. plastic foils) due to the risk of choking. DANGER If not observed, danger of electric shock. Before performing any work on the device, please disconnect from power During installation, the line to be connected bust be potential free. First, turn off power and check potential with a voltage tester. The installation of these devices is work on the power supply; consequently, it must be executed professionally according to the country specific regulation and connection requirements. Supervise children near LED spotlights in order to ensure that they do not play with them. CAUTION Low risk of injury to people. Never manipulate or change the LED spotlights. Do not use the LED spotlights if there are visible defects. On the part of the site, secure the LED spotlights only with a 10 / 16 A circuit breaker. Only connect the LED spotlights with an electrical circuit equipped with a fault current (FI) switch (max. tripping current 30 ma). Prevent mechanical sress. Ensure that the present supply voltage corresponds to that on the identification plate. If not observed, LED spotlight may malfunction. Product Description 1 Serie WR-LED 1 2 3 5 4 6 8 Serie WR-CP-LED Serie WR-CP-LED-BW -3-
No. Description Function 1 Lighting material LED 2 Fastening screw Philips screw for sealing/closing the view covering 3 Pane protects lighting material 4 Reflector Bundles light emission 5 Locking screw Screw for adjusting angle 6 Mounting bracket Mounting on wall or tripod 7 Connection Box (rear side, not illustrated) 8 Motion Detector Box to connect external connections Detects motion and turns on the light Start-up and Use Wall Mounting DANGER Only allow the installation to be performed by an authorised electrician. Through improper work on the supply system, you not only endanger yourself, but rather others as well DANGER Ensure that there are no electrical lines, water lines, etc. at the drilling points. 1. Selection of mounting location The LED spotlight is not suitable for installation on flammable surfaces. During operation, the LED sportlights generate heat. 2. Marking the mounting holes Use the mounting bracket as a drilling template and mark the 2 outer holes on the surface where the spotlight will be mounted. 3. Drilling the mounting holes Drill the mounting holes with a drill. 4. Mounting the spotlight Secure the mounting bracket to the surface with the screws. Connecting LED spotlight DANGER Only execute installation in a potential free condition. Turn off the power supply's circuit breakers. Secure these from being unintentional re-start (e.g. with a warning sign). -4-
1. Open connection box Unscrew the screws on the connection box 2. Place lines Unscew screws froms mains lead cleat and connection terminals. Insert stripped connection cable through the cable screw in the connection box. NOTE Ensure that the green/yellow protective ground wire is 3 cm longer as the other wires. 3. Connecting supply line Connect the supply line to the terminal strip. N L 4. Fasten the supply line with the mains lead cleat. 5. Close the connection box. blue green/yellow brown Function Motion Detector NOTE SENS TIME LUX 9 10 11 No. Description Function Due to the surrounding temperature, the range of the motion detector varies. The range is larger at cold temperatures than it is at warm temperatures. 9 Motion Control Setting the sensitivity of the 10 Controls for lighting duration Ensure that there are no other sources of heat (e.g. lamps) at a distance of at least 1 m. Due to the generated heat, this can lead to continuous operation of the motion detector. If plants (e.g. trees, bushes) are in the detection range of the motion detector, these may cause the light to turn on due to motion caused by wind. Please try to keep the detection range as small as possible. A large area increases the probability of incorrect switching. The detection range should be set transversely to the direction of passage. Consequently, upon passing through the area, the highest amount of sensor beams are crossed. Motion Detector Setting the lighting duration. Continuously variable between 5 seconds and 8 minutes. 11 Light sensitivity Controls setting from what daylight time or what time at dusk the sensor reacts. 9 m 120 Ill: Motion Radius Ill: Direction of Motion correct Ill: Direction of Motion incorrect -5-
Cleaning Disconnect the product from the power supply before cleaning. For the purpose of electrical safety, clean product with a slightly damp cloth. Do not use any aggressive cleaning agents, respectively chemical. Do not use a hose or high-pressure cleaner. Malfunction List Problems/ Malfunction No functions Lighting material does not light up Possible causes Power outlet has zero potential Power supply or power cord defective Lighting material defective Remedies Check the power outlet Have a professional check and replace the power cord Contact our Service Centre Visible defects Due to blous or falls Have the product checked and if necessary, repaired by a professional FI triggers Moisture in spotlight Clean and allow product to dry DANGER All further repairs may only be executed by an authorised professional repair technician or service point. Warranty and Service NOTE As of the date of purchase, you receive a 24 month warranty on this product. Contact the ROWI Electronics GmbH service point for possible returns. You may only return the product after contacting us. Postage due shipments will not be accepted. The performance of services under the warranty does not extend or renew the 24 month warranty period. Disposal The packaging and the packaging material consists of environmentally friendly material and may be recycled to 100%. The symbol indicates separate return of electrical and electronic devices in the countries of the EU. The product may not be disposed of with household waste at the end of its service life. Contact your local authorities or municipality to find out how to dispose of the device in an environmentally friendly and proper manner. By recycling old devices, you are making an important contribution to the protection of the environment. -6-
Konformität / Conformity / Conformité / Conformiteit / Conformità / Conformidad / Konformitet / Konformita In Übereinstimmung mit folgenden Europäischen Richtlinien wurde das CE-Zeichen angebracht: Die Konformitätserklärung ist beim Hersteller hinterlegt. The CE symbol was applied in compliance with the following European Directives: The Declaration of Conformity is held by the manufacturer Cet appareil porte le sigle CE pour signaler sa conformité aux directives européennes ci-dessous : Le fabricant est en possession de la déclaration. Het CE-keurmerk werd aangebracht in overeenstemming met de onderstaand vermelde Europese richtlijnen: De conformiteitsverklaring ligt ter inzage bij de fabrikant. Il simbolo CEE è stato apportato grazie al rispetto delle seguenti direttive europee: La dichiarazione di conformità è depositata presso il produttore. Al producto se le ha otorgado el símbolo CE de acuerdo con las siguientes normativas comunitarias: El fabricante dispone de la declaración de conformidad correspondiente. CE-symbolen används i enlighet med följande europeiska direktiv: Konformitetsdeklarationen finns hos tillverkaren V souhlasu s následujícími Evropskými směrnicemi byla na výrobku umístěna značka CE: Prohlášení o konformitě je uložené u výrobce. 2006/95/EC ROWI Electronics GmbH Augartenstr. 3 76698 Ubstadt-Weiher Germany service@rowi-electronics.com www.rowi-electronics.com Tel.: +49 (0)7253 880206 900 Fax: +49 (0)7253 880206 999 9/2012