Modular Indoor Systems For Effective Environmental Control Alpha Aire OmegaAir C13-Series VertiCool Aurora VertiCool Classic VariCool EZ-Fit VariCool Renovator VariCool VAV Portable Cooling and Heating Units Full-Line Brochure
United CoolAir s All-Indoor Solutions We are an Environmental Control Provider Over the years, thousands of United CoolAir systems have been installed as solutions for difficult situations such as replacing old equipment installed with limited accessibility, where there is no space for outdoor equipment or when replacement rigging costs are unmanageable. United CoolAir s modular design permits units to be taken apart to help get them through doorways, into service elevators and easily installed. Most installations can be accomplished without building alterations or renting special equipment, such as cranes or cutting the equipment apart to get the units installed. The equipment comes pre-charged with refrigerant, saving the contractor time and cost. This means that the contractor will have limited brazing to do for a split system and no brazing on site for a single package application. United CoolAir s flexibility in their design, lends itself to retrofit, renovation and replacement projects. With 98% of our units fitting through a 36" doorway or smaller and more than 100 options, United CoolAir can solve almost any environmental control challenge. Other indoor installation benefits include preventing storm damage, vandalism, any need for roof curbs, expensive rigging, permits and other items contributing to the total installed cost. Notable Clients 1 World Trade Center AT&T Bank of America CBRE Group, INC. Chicago Art Institute Chipotle Mexican Grill Columbia University Crate & Barrel Cushman Wakefield CVS Pharmacy Dayton University Dunkin Donuts Emblem Health Empire State Building Facebook FedEx Fogo de Chão Forever 21 Great Clips Hampton Inn Hilton Hotels Holiday Inn Home Depot Hyatt Regency Hotel (Boston) International Paper Johnson & Johnson World Headquarters Jones Lang LaSalle JP Morgan Chase Lillibridge LinkedIn Macy s Marriot Hotels Mars, Inc. (Headquarters) McDonalds Medimunne (Astra Zeneca) North Kentucky University NASA New York University NYC (Mayor s Office) Pay Pal PepsiCo Pier 1 Imports Rockefeller Center Rutgers University Six Flags Great Adventure Theme Park Starbucks StubHub Center The GAP, Inc. Toronto Transit Commission (TTC) Towson University Transwestern United Nations University of Florida US Post Office Verizon 2 Visit us at www.unitedcoolair.com
Lower Total Installed Cost Advantage Avoid Requirements that Lead to Extra Expense Expensive Equipment, Rigging or Permits Our units fit thru standard doors, hallways & elevators eliminating crane rentals, rigging crews & permits. Roofcurbs or Roof Penetration Removes expensive curb equipment & installation labor cost reducing possible roof water damage. Field Piping, Brazing, Evacuation or Charging Factory charged & utilizing Resealable Refrigerant Fittings speeds installation & commissioning. Excessive Downtime when Replacing Old Systems Sectional shipments accelerate installation and can be installed offhours or weekends. Architectural Damage to Building Eliminates expenses for code approvals and minimizes any type of building alteration. Compromise in Performance With Built-to-Order Design Built to exact requirements with extensive list of configurations and over 100 options. Equipment Damage Due to Weather All indoor installation avoids premature replacement costs & downtime due to weather damage. Possibility of Theft or Vandalism Eliminates expensive repairs & replacements due to theft & vandalism enhancing building security. Field Testing of Installed Product Minimizes field-testing as units are tested prior to shipment reducing labor speeding installation. Outdoor Servicing of Product Outdoor/premium service expense in extreme weather completely eliminated, improving reliability while removing roof safety issues. Major Ductwork or Electrical Modifications Units ordered to closely match existing duct and utility locations leading to labor and saving time. Exterior Condensing System Eliminates rooftop & pad installation space & cost. Resealable Refrigerant Fittings Most models feature Resealable Refrigerant Fittings. Unit sections can be shipped split or split in the field without losing the factory charge resulting in no field brazing and a total installed cost advantage. Mating male and female fittings used on the refrigerant lines allow units to be evacuated, charged and leak tested prior to shipment. Modular sections can then be separated for rigging and installation and then reconnected for system operation. Visit us at www.unitedcoolair.com 3
Horizontal Systems Air-Cooled, Water-Cooled, Chilled Water, DOAS Packaged or Split System Flexibility is paramount in today s buildings. The ability to split air conditioning units, retrofit, renovation for final installation or simply to move the unit into location, are assets that are extremely beneficial for historical sites and for renovation or replacement projects. *Refrigerant Line Lengths up to 200 Equivalent Feet! Packaged system, air cooled (or water cooled) Air cooled split system with line lengths up to 200 equivalent feet Split system matched w/remote outdoor air cooled prop fan condenser Not to scale. For illustrative purposes only. *Most Models 4 Visit us at www.unitedcoolair.com
Horizontal Systems Air-Cooled Water-Cooled Chilled Water Magna Cool Precision Cooling Package Water Source Heat Pump Air Source Heat Pump C13-Series The horizontal C13-Series product family was derived from the traditional C-Series. This unit is of the horizontal hanging type for plenum installation and can also be slab mounted or vertically stacked with the evaporator section on top, saving space. The horizontal indoor condensing section can be split from the evaporator section, reducing ducting requirements. Configured to specification allows equipment to be used for renovation and replacement projects much easier, converting it quickly to fit the specific application. Configured to Specifications Engineered to Order Air-Cooled, Water-Cooled, Chilled Water, Water Source Heat Pump or Air Source Heat Pump 2 to 10 Tons 100% Outside Air Configurations High Static Outside Wall Split System C13-Series Condenser (Outdoor Coil) Evaporator (Indoor Coil) Not to scale. For illustrative purposes only. Scroll Compressors Belt-Driven Blowers Adjustable Variable Pitch Pulleys Resealable Refrigerant Fittings Stainless Steel Evaporator Drain Pan Easy Service Access Factory Charged All sizes fit through a standard 36" doorway or smaller. Visit us at www.unitedcoolair.com 5
Vertical Systems Air-Cooled, Water-Cooled, Chilled Water, DOAS Packaged or Split System Flexibility is paramount in today s buildings. The ability to split air conditioning units, retrofit for final installation or simply to move the unit into location, are assets that are extremely beneficial for historical sites and for renovation or replacement projects. *Fits through 36" doorways, narrow hallways & elevators! Packaged indoor vertical unit using louver on outside wall Ducted vertical matched w/remote outdoor air cooled prop fan condenser Packaged indoor water cooled unit Not to scale. For illustrative purposes only. *Most Models 6 Visit us at www.unitedcoolair.com
Vertical Systems Air-Cooled Water-Cooled Chilled Water Magna Cool Precision Cooling Package Water Source Heat Pump VertiCool Aurora and Classic The VertiCool is a self-contained vertical system that is available in two series: the Classic and the Aurora. These floor-mounted units are particularly suited for tenant fit-out and for easy replacement of older units. Evaporator discharge air can be either top, front or rear, double ducted or free blow. Heat rejection is accomplished using either Air-Cooled or Water-Cooled condensing sections. The splittable feature helps to get the units into facilities for renovation projects, and the availability of multiple air path configurations make it easier to adapt the unit without extensive field alterations. Configured to Specifications 3 to 35 Tons Air-Cooled, Water-Cooled, or Water Source Heat Pump 100% Outside Air Configurations High Static Scroll Compressors Belt-Driven Blowers Adjustable Variable Pitch Pulleys Resealable Refrigerant Fittings Stainless Steel Evaporator Drain Pan Easy Component Access Factory Charged 3-15 Ton fit thru a standard 36" doorway or smaller. Aurora Configured to Specifications 3 to 30 Tons Air-Cooled, Water-Cooled, Chilled Water, or Water Source Heat Pump 100% Outside Air Configurations High Static Classic Scroll Compressors Belt-Driven Blowers Adjustable Variable Pitch Pulleys Resealable Refrigerant Fittings Stainless Steel Evaporator Drain Pan Easy Component Access Factory Charged 3-25 Ton fit thru a standard 36" doorway or smaller Visit us at www.unitedcoolair.com 7
VariCool Air-Cooled Water-Cooled Chilled Water Water Source Heat Pump Energy Recovery The VariCool EZ-Fit modular Variable Air Volume (VAV) system These floor-mounted systems are designed for easy replacement of existing floor-by-floor VAV or constant volume units with minimal modifications to current building structures. Each module is equipped with resealable refrigerant fittings and a factory charge of R-410a. This means that no field piping, brazing, evacuation or charging is required, resulting in a lower installed cost. The VariCool EZ-Fit is an ideal system for renovation and replacement projects. Individual sections fit through standard 36" doorways and into most elevators. They can also be maneuvered down narrow hallways which means no modifications or alterations to the building are needed and installation time is quicker and less costly to accomplish. Replaces Trane SWUD, Mammoth V3, Blazer, Carrier and Daikin Configured to Specifications 12 to 45 Ton Single Modules 24 to 90 Ton Dual Modules Modular Floor-by-Floor Systems Ships In 3 to 8 Sections Air Cooled w/remote Condenser Water-Cooled, Chilled Water Water Source Heat Pump 100% Outside Air Configurations Multiple Cabinet Dimensions High Static Fits through 36" doorways, narrow hallways & elevators! Modular Unit Shown with optional DDP fans EZ-Fit Variable Speed Compressor The highly requested, optional variable speed compressor is available in the VariCool EZ-Fit Units. Dual Scroll Compressors Per Module Interlaced Evaporator Coils Premium Efficiency Motors Double Sloped Stainless Steel Drain Pan Hot Gas Bypass (each circuit) Lift Off Hinged Panels Belt Drive Airfoil DWDI Blower (12-25 Ton Modules), DDP Blowers (30-45 Ton Modules) Backward Inclined Blades Factory Mounted VFD Controller Marvel Premium Microprocessor Controller Optional Variable Speed Compressor Optional ECM Fans 8 Visit us at www.unitedcoolair.com
VariCool Water-Cooled VariCool Renovator The VariCool Renovator is a direct replacement for retrofitting existing Trane SWUD units. Our modular design allows for efficient change-outs. Individual sections fit through standard 36" doorways or smaller. Water-Cooled Only Coaxial HX EC Impeller Fan Grid Electronic Head Pressure Control Ships Knocked Down (10 sections) Factory Charged & Tested Marvel Premium Microprocessor NEW Shell & Tube HX Waterside Economizer Replaces Trane SWUD Models 042 080 fitting within existing footprint OPTIONS Inverter Compressors Coated Coils VariCool Variable Air Volume (VAV) system The unit is designed as a floor-by-floor air conditioning system offering flexibility for tenant fit-out as well as tighter tenant control of space conditions. Scroll Compressors Row-Split Evaporator Coils Premium Efficiency Motors Double Sloped Stainless Steel Drain Pan Hot Gas Bypass (each circuit) Lift Off Hinged Panels Spring Isolated Plenum Fan and Motor Factory Mounted VFD Factory Charged Marvel Premium Microprocessor Controller 6 Row Evaporator Coil Row-split evaporator configuration provides uniform and precise leaving air temperatures under a variety of operating conditions. Configured to Specifications 9 to 70 Tons Modular 3 Piece Design Water-Cooled, Chilled Water 100% Outside Air Configurations Down-flow Configuration Available 6 Row DX Coil 2" Fiberglass Insulation High Static VariCool VAV Blower Assembly Spring isolated airfoil plenum fan and motor assembly with pillow block bearings at 200,000-hour life expectancy. Refrigeration Module All critical components are located outside the air stream so the unit can be serviced without disturbing the airflow/performance. Visit us at www.unitedcoolair.com 9
Alpha Aire Air Source Heat Pump Energy Recovery A single source solution for Environmental Control Units Improving Indoor Air Quality Indoor air quality can be adversely affected by many factors. Indoor pollutants can lead to a variety of health risks, especially for those already susceptible to such factors. Studies show that introducing conditioned outside air can lead to better health and performance Alpha Aire DX DOAS Unit w/energy Recovery Dehumidification Mode Value United CoolAir Alpha Aire ASHRAE Minimum* ISMRE 5.2 11.1 ASHRAE Minimum* ISCOP 3.3 8.0 *Table 4 ASHRAE 90.1 2016 Minimum Values of occupants in a variety of settings. ASHRAE 62.1-2016 requires minimum OSA CFM s per code. Alpha Aire is the first choice in introducing low CFM fresh air into buildings for a simple and quick installation for challenging or existing retrofit applications. Alpha Aire Features & Options United CoolAir uses high-density 2" Thermal/Acoustic Insulation with Solid Double Wall Liner along with low airflow to greatly reduce noise for near occupant operation. Critical components are isolated out of the air stream for longer life, and prevent unwanted condensate formation. Single point electrical power and 8" flex duct make for a low cost installation. The sheet metal is G90 galvanized steel with optional exterior paint finish for durability and long life. OPTIONS Painted Cabinet Exterior Only Non-fused Disconnect Coated Coils Buck Boost Transformer External Condensate Pump 4" MERV 11 or 13 Filters Smoke Detector Occupancy Switch VOC Switch CO2 Switch Floor Stand Alpha Aire 100 500 CFM Air Source Heat Pump Compressor Acoustic Covers Energy Recovery Wheel Low Supply Air Dew Point Temps ECM Fans Self Contained DX System Single Cabinet Design Auxiliary Reheat Coil Variable Air Volume Capable (Via BMS) Up to 1" of ESP Field Convertible Return/Supply Air Panel Stainless Steel Drain Pans 2" MERV 8 Pleated Throwaway Filters 208/230-1-60 power 10 Visit us at www.unitedcoolair.com
OmegaAir Air-Cooled Water-Cooled The OmegaAir DOAS is designed specifically for indoor installations OmegaAir provides air flow capabilities from 150 CFM up to 3000 CFM of room neutral air (70 F to 72 F with 50% RH). The low CFM range is ideal for independent zoning of spaces with different outside air demands. Air dew point design temperatures are lower than standard air conditioners to remove the maximum amount of moisture before delivery to the space. A Marvel Premium microprocessor controller monitors and controls every aspect of the unit s operation for year-round performance. The OmegaAir system accurately delivers precise air temperature and humidity regardless of the changing outside air conditions. It is an excellent choice for renovation projects where outside mounting is unavailable or not desirable. Inside mounting enhances the architectural integrity of the building while bolstering security concerns for the unit. Configured to Specifications Vertical or Horizontal Configurations 150 to 3,000 CFM Water-Cooled or Air-Cooled Air-Cooled with Indoor Ducted Condenser or Remote Outdoor Condenser Meets ASHRAE 62.1 ventilation requirements OmegaAir vertical units have a small footprint. The OmegaAir horizontal configuration saves valuable floor space when ceiling mounted. Air-Cooled Remote Condenser (Indoor or Outdoor) Outdoor shown Designed Specifically for Indoor Installations Rugged Cabinet Construction and Finish 2" Thermal/Acoustic Insulation No Thermal Bridging Draw-through Airflow Interlaced Evaporator Coil Sloped Stainless Steel Drain Pan Internally Mounted Condensate Trap Hot Gas Bypass Modulating Hot Gas Reheat Marvel Premium Microprocessor Controls Compressor(s) and Electrical Components Isolated from Air Stream Single Point Power Optional Electric Heat Optional Digital Scroll Compressors Building Management System Compatible (optional interface card) All sizes fit thru a standard 36" doorway or smaller Visit us at www.unitedcoolair.com 11
Marvel Series Microprocessors BMS Marvel Premium and Mini Replace All Legacy Microprocessors The Marvel Premium is a full featured microprocessor based electronic programmable controller with a multi-tasking operating system used to control United CoolAir manufactured environmental control systems using a newly developed Multi-Application software package. The Marvel Mini is a basic controller. Both the Marvel Premium and Mini replace all previous applications provided by United CoolAir, and are now bundled into two software packages. These robust devices now handle standard heating, cooling, dehumidification, humidification, as well as the heat pump, variable air volume, and outdoor air applications. MARVEL PREMIUM TM MARVEL MINI TM Prem Mini Marvel Marvel One controller hardware platform for All Applications One Software Package for the controller with greater flexibility per customer application Fully Configurable Analog/Digital Input and Outputs Any Functions available on an input or output are also configurable to other like inputs or outputs Up to Four Stages Cooling/Four Stages Heating/ Four Stages Heat Pump/100% Outside Air Configurable for Digital or Variable Speed Compressors Input/Output Expansion Boards Available for Complex Applications (may require software upgrade) Networking Lead/Lag Backup Assist with normally closed switched Ethernet Ports Newly added Single Zone Variable Air Volume BACnet, ModBus or LonWorks capable Offered as a lower cost alternative solution to Marvel Premium for smaller systems One Software Package for the controller with greater flexibility per customer application Fully configurable Analog/Digital Inputs and Outputs Maximum of One Compressor and One Heater per unit Airside Economizer or Waterside Economizer or Chilled Water Networking: Available with Lead/Lag, Unit Backup, Assist, and Unit Rotation Applications: Constant Air Volume, Heat Pump or 100% DOAS BMS Solutions: (BACnet Modbus ) LEGACY MICROPROCESSORS Internet of Things United CoolAir Corp. offers remote connectivity for control & diagnostics. J Marvel S Marvel Plus Marvel OA3 Marvel These Marvel Microprocessors are no longer available in current production models. Installation and operations manuals are still obtainable at www.unitedcoolair.com for reference only. 12 Visit us at www.unitedcoolair.com
Manufactured for Specific Applications Quality Built, Flexible Features Separate United CoolAir from the Rest Built to Specific Applications Various Heat Exchanger & Fan Options Heavy Gauge Metal for Robust Construction Flexible Unit Dimensions Manufactured for Retrofit/Renovation Market Functional Run Tests are Conducted on Every Unit Limited Warranty, One (1) Year on Parts and Five (5) Years on Compressors Made in USA APPLICATIONS Schools/Universities Office Spaces High Rise Buildings Lobbies Conference Rooms Elevator Rooms Hospitals/Clinics Clean Rooms Telecommunications Computer Rooms Hotels/Casinos Industrial / Caustic Retail Stores Bars/Taverns Restaurants Theaters Night Clubs Fitness Centers Churches Convention Halls Manufacturing Facilities Animal Shelters Historical Buildings Visit us at www.unitedcoolair.com 13
A Variety of Options and Configurations CABINET High Static Pressure Acoustic Foam Insulation Painted Heresite Coated 3 Way Regulating Valve Digital Scroll Compressor Air-side Economizer Vertical Stacked Discharge Plenum Utility Connection Location Water Flow Switch Resealable Refrigerant Fittings Liquid Receiver Outdoor Modification Kit Free Cooling Coil Perforated Wall Construction Magnahelic Guage Hot Water Coil 2 Way Regulating Valve Modulating Hot Gas Bypass Electro-Coil Coated Unit Mounted Sensors Dirty Filter Switch Supply / Return Air Grille High Heat Limit Plenum Duct Flange Steam Canister Humidifier Various Air Paths BMS Interface Cards Condenser Filter Box External Hot Gas Bypass Quench Valve Shell & Tube Heat Exchanger Dry Contacts Anti-Short Cycle Timer Copper / Copper Condensate Pump Johnson Controller w/ SCR Wall Mounted Thermostat Tubular Electric Heat / Reheat Steam Coil Chilled Water Coil Buck / Boost Transformer Hot Gas Reheat Heresite Coated Coil Reduced Height Water- Cooled Section Open Wire Electric Heat Direct Drive Marvel S 2" Merv 8 2" Merv 11 Humidistat Filter Rack Firestat Dehumidistat Oil Separator 2" Merv 13 Freezestat 4" Merv 8 COIL CONDENSER FILTER COMPRESSOR OVER 100 OPTIONS! Marvel Plus 4" Merv 11 VFD Low Ambient Control Remote ON/OFF Dual vs. Single Compressor Marvel J DDP Fans (Varicool EZ-Fit) Compressor Acoustic Cover Phase Reversal Relay Cupro Nickel Heat Exchanger 4" Merv 13 OA3 Controller Marvel Expansion Module Solid Double Wall Construction Liquid Line Shutoff Valve Kele Module w/ Multiple Compressors Electronic Head Pressure Control Valve Wall Mounted Sensors Marine Duty Regulating Valve Evaporator Section Stand Flooded Low Ambient Control Refrigerant / Water Piping Connections Split Shipment Cabinets Waterside Economizer Brazed Plate Heat Exchanger Crankcase Heater Variable Frequency Drives Air Flow Switch Non-Fused Disconnect Programmable Wall Mounted Thermostat Remote Condenser Drain Pan Overflow Switch Hot Gas Bypass Shutoff Valve Smoke Detector Suction Line Accumulator Interconnect Kits REFRIGERANT CONTROLS MICROPROCESSOR BLOWER ACCESSORIES Grow Room Units Indoor grow facilities are popping up across the country at a rapid rate and there is a growing need to properly condition these spaces. The cooling equipment needs to adapt to the plant s environmental requirements as it progresses through its life cycle, which is why the common comfort cooling units do not provide the required control for the facilities. United CoolAir has developed a high performing system that utilizes a variable speed compressor, ECM blowers, full condensing hot gas reheat and a sophisticated control package. United CoolAir grow room units are available in a wide range of tonnages, vertical & horizontal configurations, split air cooled and packaged water cooled systems to meet all of your indoor grow facility requirements. Engineered Systems United CoolAir designs and manufactures specialty air conditioning systems for specific space, function and operating requirements. These are highly specialized units that can be used as standalone units or as a component part of an OEM system. For one-of-a-kind comfort and precision cooling applications, United CoolAir Corporation also designs and manufactures custom air conditioning systems. We work closely with OEMs to provide solutions that meet unique cooling requirements. CoolSpot Ductless Ground Support Air Conditioning Units for Aircraft High Ambient UPS Cooler / DX & Chilled Water 14 Visit us at www.unitedcoolair.com VertiCool Space Saver Disaster Recovery Unit Mobile Print Facility Truck Cab Conditioning Mobile Shooting Range
Mobile Environmental Control Units Air Conditioners Designed Exclusively for Temporary Cooling/Heating and Dehumidification United CoolAir manufactures a variety of temporary environmental control units marketed under the Therm~Air brand. These mobile systems are the most cost-effective solution for a wide variety of temporary cooling, heating and dehumidification applications. Therm~Air units are flexible, dependable, reliable and durable. As with our commercial units, Therm~Air portable cooling and heating equipment can be tailored to your specific requirements. Each unit is manufactured to meet rigid requirements with a proven record of long life under demanding conditions. Therm~Air portable equipment provides an excellent ROI over less expensive modified commercial units that last only a year or two. Vertical and Horizontal Units 3 30 Tons Cooling Only, Cooling with Heat and Heating Only Ducted or Free Blow 4-Way Forklift Pod & Corner Lifting Brackets Quarter Turn Latches on Access Panels Premium White Powder Coat Finish Stainless Steel Hardware Welded Construction Insulated Cabinet Sections Buy Factory Direct Portable/Mobile Systems for a Wide Variety of Applications General Applications Temporary Structures Back-Up Cooling Spot Cooling Emergency Cooling Water Remediation Fire and Water Restoration Construction Drying Heating Dehumidification Office Buildings/ Schools Computers/ Telecommunication Off-Hour Night/ Weekend Cooling Renovation Humidity Control Kitchens Heating Dehumidification Industrial Applications Temperature-Sensitive equipment Manufacturing Spot Cooling Spot Cooling for Personnel Vessel Cooling Plant Shutdowns Warehousing Heating Dehumidification Special Events Tent Functions Sporting Events Corporate Functions Outdoor Weddings Movie Studio Productions Exhibit/Conference Halls Heating Dehumidification Special System Portable Shelter Systems Ground Support Marine Applications Disaster Recovery High & Low Conditions High Static Products can be configured with select features and a wider variety of options than what are listed. Please contact United CoolAir for other models and configurations. Visit us at www.unitedcoolair.com 15
Modular Indoor Systems for Effective Environmental Control VertiCool Classic Vertical, 3-30 Ton VertiCool Aurora Vertical, 3-35 Tons Portable Cooling and Heating Units 3-30 Tons Authorized Representative: C13-Series Horizontal 2-10 Tons VariCool VAV, 9-70 Tons VariCool EZ-Fit VAV, 12-90 Tons C-Series Horizontal 1-15 Tons Special Configuration Engineered to Order Alpha Aire 100 500 CFM OmegaAir Horizontal and Vertical 100% Outside Air 150 3000 CFM LIMITED WARRANTY United CoolAir Units are backed by a 1 year limited warranty on parts and a 5 year limited warranty on the compressor (labor not included). Maintenance items such as filters and belts are excluded under this limited warranty. FACTORY TESTED All units are functionally run tested before shipment to ensure a trouble-free start-up and unit commissioning. Industry proven components are used throughout to enhance system reliability and peace of mind. Scan to learn more about all of our products! 491 East Princess Street, York, PA 17403 Phone: 717-843-4311 Fax: 717-854-4462 email: uca@unitedcoolair.com web: www.unitedcoolair.com Copyright by United CoolAir Corporation 2018. All rights reserved. Manufacturer reserves the right to make changes without notice. 05.10-SB (1218)