UV LED SPOT CURING SYSTEM ADD:, No. 2 of Qinglong Rd, Longhua, Shenzhen, 518109, China TEL: +86 755 27528108 FAX: +86 755 29641518 WEBSITE: www.szlamplic.com EMAIL: szlamplic@hotmail.com
ADVANTAGES 1). Environment-friendly: No Mercury, No ozone 2). No infrared light, No heat radiation, Normal temperature 3). Long Life: 20000+ hours for advanced LED radiation head 4). Instant ON&OFF, don t need preheating 5). Low cost: don t need to change lamp, save 80% of energy OPTIONAL WAVELENGTH Far UV: 240, 245, 250, 255, 260, 265, 270, 275, 280, 285, 290, 295 nm Near UV: 300, 305, 310, 315, 325, 335, 345, 355, 365, 385, 395, 405, 415 nm Visible light: 420, 430, 450, 470, 490, 500, 505, 525, 535, 545, 565, 570, 580, 590, 605, 625, 630, 645, 660, 670, 680, 690, 700, 720, 735, 750, 760, 780 nm Spectrum bandwidth: ± 5 nm UV LED SPECTRUM UV LED LIGHT DECAY
UV LED SPOT LIGHT GUIDE (1) Fan cooling: excellent heat dissipation performance, suitable for continuous radiation for long time. (2) Natural cooling: No vibration, suitable for using in small space or clean room, not suitable for long time continuous radiation LED Spot Intensity Cooling Facular Focal Head Model Picture & Dimension for 365nm Method Diameter Distance NO. (mw/cm2) LHFC084-03 Φ3mm 9mm 10000 LHFC084-04 Φ4mm 10mm 9000 LHFC084-06 Fan Φ6mm 17mm 4000 LHFC084-08 Cooling Φ8mm 20mm 2300 LHFC084-10 L88mm or L188mm Fan:24*24*24mm Φ10mm 25mm 1100 LHFC084-12 Φ12mm 30mm 800 LHS049-03 Φ3mm 9mm 10000 LHS049-04 Φ4mm 10mm 9000 LHS049-06 LHS049-08 Natural Cooling Φ6mm Φ8mm 17mm 20mm 4000 2300 L66mm LHS049-10 Φ10mm 25mm 1100 LHS049-12 Φ12mm 30mm 800 LHS118-03 Φ3mm 9mm 10000 LHS118-04 Φ4mm 10mm 9000 LHS118-06 LHS118-08 Natural Cooling Φ6mm Φ8mm 17mm 20mm 4000 2300 LHS118-10 L118mm Φ10mm 25mm 1100 LHS118-12 Φ12mm 30mm 800 Notes: Spot diameter means the uniform light diameter at the recommended distance
UV LED SPOT LIGHT GUIDE STRUCTURAL DRAWING UV LED SPOT SYSTEM S CONTROLLER
UVEC-4II UVEC-4IIController Model UVEC-4II Name UV LED curing heads QTY 1-4 PCS of Spot LED heads 1-2 PCS of linear/area LED heads Dimension for UVEC-4II 180L*100W*146H(mm) Dimension for UVEC-4III 156L*100W*163H (mm) Terminal I/O Input Foot pedal & serial RS-232 signals Output serial RS-232 communication signals Cooling method Semiconductor cooling Power setting 0 100% Time setting 0-999.99 S Radiation Mode Fixed power Step power Manual Constant power radiation Step power radiation Foot pedal control after setting Power supply voltage AC220V±15% ( 50/60HZ ) Environmental temperature 0 50 Environmental humidity MATERIAL ADDITIONAL 20% 80% RH ALUMINUM Operating Manual, Key, Cables, Power supply THE STRUCTURAL DRAWING OF UVEC-4II
Safety Instructions: Precautions described in the present note intended to illustrate the safe and proper use of the equipment, and to prevent the operator and others from hazards in advance. Read the following precautions to avoid unnecessary losses and damage. 1. Plug in the power, open the switch on the back of the controller, and then open the controller panel key lock. According to the control mode, select the panel button or foot switch to control the irradiation. 2. Supply voltage (100V-220V/60HZ-50HZ), power adapter input, DC12V 4A. 3. In the working process of this product, it is strictly prohibited to gaze the direct light, reflected light, or irradiate human skin directly or reflexly. 4. The operator must wear UV protective glasses and gloves and other protective UV protection tools; otherwise, it may cause inflammation of the eyes, skin, and etc. 5. Prohibited to disassemble, repair alteration the controller that may cause the device quality problems, accidents, personal injury. Keep the device body horizontally and correct used, not tilted, traversed or inverted to use; Otherwise, the equipment might be damaged and affect personal safety. 6. The device does not have a waterproof, need to be kept clean and dry. 7. Prohibited twist, disassemble irradiation head, so as not to affect the ultraviolet energy output and output quality. 8. Scrubbing equipment with dry paper towel lightly. 9. Not to touch UV irradiation head when the power on or power off shortly, so as not to burn human skin. 10. Do not let water and other liquid dripped or splashed on the device. 11. Keep away from the high-pressure machinery, power machinery, heating and heat source. 12. Do not put debris on the device and device-independent things. 13. Prohibited in the electrostatic places use the device to prevent electrostatic discharge. MAIN APPLICATIONS (1) UV light curing: optical equipment, optical communication products and crafts manufacturing, electronic components, hard drives, and micro-motor manufacturing, manufacturing headphones and watch parts, optical DVD / CD production. (2) UV detection and analysis instrument: UV analyzers, for bio-genetic engineering, molecular genetics, medical health, biological products, pharmaceutical research, sanitation and epidemic prevention, dyes chemical, petrochemical, textile industry, public security and judicial departments, cultural relics archaeological department, and wherever fluorescence analysis test is needed. (3) UV disinfection: it can be widely applied in various areas of need for water disinfection. (4) Biological applications: Sterilization, Plant physiology research, Seed quality research (5) Medicine and Medical Applications: Medical diagnosis and treatment: dental curing,
vitiligo treatment, Bio-pharmaceutical applications, In drug production and research