REVE INSTALLATION INSTRUCTIONS ELONGATED TWO-PIECE TOILET K-17178T-S2/K-17178T-SBG2/K-17178T-SP2 Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operating and safety instructions. All information in these instructions is based upon the latest product information available at the time of publication. Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. These instructions contain important care, cleaning, and warranty information - please leave instructions for the consumer. - ORDERING INFORMATION REVE Two-Piece Toilet (P-trap)...K-17178T-SP2 Includes Elongated Bowl...K-17179T-BP2 Includes Tank... K-17180T-TM2 Includes Quiet-Close Toilet Seat... K-17183T-CP REVE Two-Piece Toilet (S-trap)...K-17178T-S2 Includes Elongated Bowl...K-17179T-2 Includes Tank...K-17180T-2 Includes Quiet-Close Toilet Seat...K-17183T-CP REVE Two-Piece Toilet (S-trap)...K-17178T-SBG2 Includes Elongated Bowl...K-17179T-2 Includes Tank...K-17180T-BG2 Includes Quiet-Close Toilet Seat...K-17183-BG ( )...K-17178T-SP2...K-17179T-BP2... K-17180T-TM2... K-17183T-CP ( )...K-17178T-S2...K-17179T-2...K-17180T-2... K-17183T-CP ( )...K-17178T-SBG2...K-17179T-2...K-17180T-BG2...K-17183T-BG NOTES Observe all local plumbing and building codes. Shut off the water supply. Seat post holes are on 200mm centers. Water depth from the rim is 257mm. Ensure that the new drain has the correct roughing-in dimension. This toilet has a 305mm (S-trap) roughing-in dimension and a 185mm (P-trap) roughing-in dimension. See Roughing-in. Closet flange must be 185mm on-center from wall or 305mm on-center from floor. Carefully inspect the new fixture for any sign of damage. For new construction, refer to the dimensions in installation step for locating the shut-off valve. Fixture dimensions are nominal and conform to tolerances established by ASME Standards (A112.19.2-2013). The product complies with GB 6952-2015. 200mm 257mm 305mm( 185mm ) 2013) GB 6952-2015 305mm ASME 185mm (A112.19.2- No.2 KOHLER ROAD, SANSHUI CENTRAL INDUSTRIAL PARK, LEPING TOWN, SANSHUI DIST., FOSHAN, GUANGDONG, PRC POST CODE 528137 2 528137 8# MENGSHAN RD, ECONOMIC DEVELOPMENT ZONE OF HUANTAI, ZIBO, SHANDONG, CHINA POST CODE: 256410 8 256410-1- Copyright Kohler China Investment Co., Ltd. 2016 2016
WARNING: Risk of personal injury or product damage: Handle vitreous china products very carefully. Vitreous china can break and chip if you overtighten bolts and nuts. WARNING: Risk of external leakage. The fill valve nut has been factory-tightened to design specifications. If re-tightening is required, wrench tighten one turn past finger tight. IMPORTANT! Make sure the supply pressure is a 2 minimum of 35 psi (2.5 kg/cm ). The toilet will not function properly without minimum Pressure. 35psi( 2.5 kg/cm 2 ) TOOLS AND MATERIALS REQUIRED (Not supplied) 254mm (10") adjustable wrench 305mm (12") pipe wrench Metal file (file cut) Tape measure Tubing cutter Level Hacksaw Putty knife Screwdriver Toilet gasket (wax seal) Toilet installation flange Toilet T-bolts (2), 8mm (5/16") diameter Toilet supply shut-off valve, 10mm(3/8 ") recommended 254mm 305mm 8mm T 2 10mm NOTICE: If the existing toilet does not have a supply shut-off valve below the tank, install one before installing the new toilet. Reference Value 135 Unit: mm : 880 102 410 185 A 185 220 185 110 200 370 305 Fig. #1 1 Kohler reserves the right to change marked dimensions without prior notice. 45 685 460-2-
305mm INSTALLATION (For S-trap Toilet) 1 Install or relocate the supply and outlet as necessary to conform to the roughing-in dimensions. 360 251 886 165 305 3/8NPT Supply 127 216 160 280 Important: Toilet must have 305/185 mm minimum rough-in to install properly. 305/185mm Fig. #2 2 2 If replacing a toilet, remove the old wax. Fig. #3 3 3 Position the template. 4 Tape in place and drill holes. Finished Wall 170mm 160mm Suggested a Gap of 3mm 3mm Wax Ring Plate O.D 195mm 195mm 3/8 Fig. #4 4 Fig. #5 5-3-
5 Insert anchors. 6 Install brackets. 3/8 NPT Supply 127mm 216mm 80mm 80mm Anchor Fig. #6 6 Fig. #7 7 7 Thread the supply hose onto the tank. 8 Slide nut onto the supply hose, with flared end last and run hose through toilet wall. Fig. #8 8 Fig. #9 9 9 Position the tank on the bowl. 10 Slide the hose guide onto the hose, with the flared end last. Slide the two inserts into the flared end of the hose guide. Hose Guide Fig. #10 10 Fig. #11 11-4-
11 Slide the metal washer and the rubber washer onto the bolt. 12 Rotate the flush valve to loosen the clip that secures the flush valve with tank bottom. Lift the flush valve upwards to detach the valve body from the valve seat. Metal Washer 1 2 Fig. #12 12 Fig. #13 13 13 Thread the bolts into the bowl through the bolt holes in the bottom of the tank. Tighten the bolts using a screwdriver. Do not overtighten. 14 Press the flush valve downwards onto the valve seat, rotate the assembly clockwise, and lock the clip that secures the valve seat with tank bottom. Bolt Fig. #14 14 Fig. #15 15-5-
15 Install the wax ring to the underside of the wax ring plate. Press evenly. Mount wax ring plate with T-bolts. 16 Align outlet and carefully lower over brackets. T Wax Ring Plate Wax Ring T-Bolt T Fig. #16 16 Fig. #17 17 17 Apply weight evenly. Do not move after placement! Watertight seal may be broken! 18 Carefully thread the screws into the brackets, until toilet is secure. Alternately tighten left and right sides to prevent pulling the toilet off center. Install cap to cover screw. Do not overtighten. Bushing Cap Screw Fig. #18 18 Fig. #19 19-6-
19 Caulk around base. Caulk Fig. #20 20 20 Connect supply and turn on the water. 21 Remove the tape and protective pad. Tank Cover 3/8" Supply 3/8" Fig. #22 22 Fig. #21 21 22 Press down on the large button. 23 Pull out and remove the small button. 24 Pull out and remove the large button. Fig. #23 23 Fig. #24 24 Fig. #25 25-7-
25 Press the large button onto the black rod. 26 Press the small button onto the green rod. Large Button Small Button Green Rod Black Rod Fig. #26 26 Fig. #27 27 27 Insert the rods into the holes in the push button housing. 28 Press down on the push buttons until they click into place. Fig. #28 28 Fig. #29 29 29 Flush several times and check for leaks. 30 Turn here to adjust the water level. WL-P(For P-Trap Only) ( ) Fig. #30 30 Fig. #31 31 WL-S(For S-Trap Only) ( ) 31 Install the tank lid and the seat. Use the supplied 1/4"-20 seat bolts and washers. Periodically check for leaks for several days following the installation. 1/4"-20 Fig. #32 32-8-
Replace the Seal 1 Shut off the water supply. 2 Remove the tank cover. Fig. #33 33 Fig. #34 34 3 Rotate the flush valve to loosen the clip that secures the flush valve with tank bottom. 4 Lift the flush valve upwards to detach the valve body from the valve seat. Fig. #35 35 Fig. #36 36 5 Replace the seal. 6 Press the flush valve downwards onto the valve seat, rotate the assembly clockwise, and lock the clip that secures the valve seat with tank bottom. Fig. #37 37 Fig. #38 38-9-
7 Reinstall the tank cover. 8 Turn on the water supply. Fig. #39 39 Fig. #40 40 9 Flush several times and check for leaks. Fig. #41 41 SYMPTOMS RECOMMENDED ACTION 1. Poor flush. A. Adjust the tank water level to match the waterline. B. Fully open the water supply shut-off valve. C. Clear obstructions from the trapway, jet or bowl rim holes. D. Clear obstructions in the soil pipe or vent pipe. 2. No flush. A. Make sure the push button rods are in place. Adjust as needed. 3. The fill valve turns on/off by itself or it runs, allowing water to enter the Tank. 4. Long tank fill Cycle. 5. Noisy tank fill Cycle. A. Adjust push button rods for proper slack so the flush valve seal isn't held off the flush valve. B. Clean or replace the flush valve seal if it is worn, dirty, or misaligned with the valve seat or flush valve seat is damaged. C. Replace the flush valve gasket. D. Clean the fill valve seat/seat washer of debris or replace the piston/seat washer assembly. E. Replace the fill valve if the valve float sinks. F. Adjust the tank water level if it is too high. A. Fully open the water supply shut-off valve. B. Clean the valve inlet, valve head, or supply line. Flush the Lines. A. Partially close the water supply shut-off valve if the water pressure to the toilet is too high. Check the toilet performance following any such adjustment. B. Remove dirt or obstructions from the valve head. Flush the Lines. -10-
1. A. B. C. D. 2. A. 3. / A. B. 5. A. C. D. / E. F. 4. A. B. B. CONSUMER RESPONSIBILITIES If you live in a hard water area, make certain that the holes in the toilet rim are kept clean to ensure proper bowl flushing. Toilet bowl cleaners should be used at least once a week. Use a long-handled brush to clean the rim holes, and to clean as far into the trap as possible to prevent mineral deposits from forming. Most toilet bowl cleaners are not harmful to the vitreous china surface of the toilet bowl. Please follow the bowl cleaner manufacturer's instructions carefully. Do not use abrasive cleaners or solvents. WARNING: Risk of property or product damage. Do not use in-tank cleaners. Products containing chlorine (calcium hypochlorite) can seriously damage fittings in the tank. This damage can cause leakage and property damage. Kohler Company shall not be responsible or liable for any damage to these tank fittings caused by the use of cleaners containing chlorine (calcium hypochlorite). ( ) CAUTION: Don' t use any cement while installing the toilet. Heat expansion of the toilet may damage the feet of the toilet. Kohler will not be responsible for any damage because of using cement. WARNING: Risk of product damage. Do not throw into the toilet what is easy to block it, such as newspaper, paper pilch, sanitary towel. Do not bump the vitreous china with great force to prevent it from damaging and leaking. o Do not use the product in the water below 0 C. 0C o CAUTION: Please do not use hard materials (like scouring pad) to clean product surface, especially the product logo. -11-