Manual Controller LED X-Dimmer 3F
Table of Contents 1. Safety instructions... 3 1.1. FOR SAFE AND EFFICIENT OPERATION... 3 3. Control... 5 3.1. Setting the current... 5 3.2. Addressing in DMX mode... 6 3.3. Manual mode... 7 3.4. Automatic mode... 8 4. IR remote... 9 5. Technical data... 10 2 / 12
1. Safety instructions Read the safety instructions and also this manual carefully. Keep the manual. Observe all red flags. Observe the manual. To prevent fire or electric shocks, protect the device against rain and humidity Pull the plug before opening the housing. To prevent an electric shock you should not remove the cover. Do not operate the device in the near of water. Use only a dry cloth for cleaning. 1.1. FOR SAFE AND EFFICIENT OPERATION Be careful with heat and extreme temperature Avoid exposing it to direct rays of the sun or near a heating appliance. Not put it in a temperature bellow 41 F /5 C, or exceeding 95 F /35 C. To avoid placing on un-stable location Select a level and stable location to avoid vibration. Do not use chemicals or volatile liquids for cleaning Use a clean dry cloth to wipe off the dust, or a wet soft cloth for stubborn dirt. Pull the plug before cleaning. If out of work, contact sales agency immediately Any troubles arose, remove the power plug soon, and contact with an engineer for repairing, do not open the cabinet by yourself, it might result a danger of electric shock. Take care with the power cable Never pull the power cable to remove the plug from the receptacle, be sure to hold the plug. When not using the device for an extended period of time, be sure to disconnect the plug from the receptacle. Ventilation It is not allowed cover fans and air in and outlets. 3 / 12
Safety Do not remove the grounding. It is for your safety. If you remove the grounding it can cause electric shocks. Accessory Please use only the accessory which is set by the manufacturer. Important Damages caused by the disregard of this user manual are not subject to warranty. The dealer will not accept liability for any resulting defects or problems. Make sure the electrical connection is carried out by qualified personnel. All electrical and mechanical connections have to be carried out according to the European safety standards. 4 / 12
3. Control 3.1. Setting the current You can set the maximum output-current per channel from 350mA to 700mA, by using the built-in Dipswitch 1. Use the screwdriver to open the housing like shown in the pictures below. 2. Set the dipswitch to the respective position to make the required setting. Strom 2 1 350 ma Off Off 700 ma On On While built-in dipswitches are Off, the device will output 350mA current, the current indicator on the front panel will black out. While both built-in dipswitches are On the device will output 700 ma current, the current indicator on the front panel will light. 3. Close the housing of the device. 5 / 12
3.2. Addressing in DMX mode In this mode the dipswitch 11 has to be set to On. You can set the DMC address and regulate the intensity of light. The outputs 1-4 will be controlled by channel 1-4. You can set the DMX address with the dipswitches 1-9. The dipswitches represent a binary value and allow an individual adjustment of the values 1-511. The binary values and examples to individual start addresses reach are given in the following tables. Dipswitch Binary Start Dipswitch Start Dipswitch On value address On address 1 1 1 1 11 1,2,4 2 2 2 2 12 3,4 3 4 3 1,2 13 1,3,4 4 8 4 3 14 2,3,4 5 16 5 1,3 15 1,2,3,4 6 32 6 2,3 7 64 7 1,2,3 8 128 8 4 9 256 9 1,4 510 2,3,4,5,6,7,8,9 10 2,4 511 1,2,3,3,4,5,6,7,8,9 6 / 12
3.3. Manual mode You can control this device both with fader as with the dipswitches. For the colors red, green blue you have got a separate fader. If you want to control the device with the dipswitches follow the following instructions. In this mode the dipswitch 10 and 11 have to be set to Off. You can control the intensity of red, green, blue with the help of the dipswitches, from 0-100%. The dipswitches represent a binary value and allow adjusting the dimming value from 0-100%. The binary values and examples to individual dimming levels reached are given in the following tables. Intensity Red Dipswitch 1-3 Green Dipswitch 4-6 Blue Dipswitch 7-9 0% 000 000 000 14% 100 100 100 28% 010 010 010 43% 110 110 110 57% 001 001 001 71% 101 101 101 86% 011 011 011 100% 111 111 111 7 / 12
3.4. Automatic mode In this mode the dipswitch 10 has to be set to On and the dipswitch 11 has to be set to Off. With dipswitch 1-3 you can set the fade time, with dipswitch 4-6 the speed and with dipswitch 7-9 the patterns are set. The following table will show which will produce what results. Setting dipswitch Fadetime dipswitch 1-3 Speed dipswitch 4-6 Pattern dipswitch 7-9 000 0 128s 1 100 14% 64s 2 010 28% 32s 3 110 43% 16s 4 001 57% 8s 5 101 71% 4s 6 011 86% 2s 7 111 100% 1s Automatic programs 1-7 in a loop. 8 / 12
4. IR remote This device allows you to control it via an IR remote (the IR remote uses following battery type: 3V, CR2025). The IR remote has a range of 10m. Please make sure that you have isolated the mains and connect the IR EYE sensor to the device. If you have made your desired setting you can disconnect the IR EYE sensor. Never remove the external IR sensor, when powering on for preventing a damaging. You can make the following setting with the IR remote. Button Function RED Dimmer red 0-100% GREEN Dimmer green 0-100% BLUE Dimmer blue 0-100% CYAN MAGENTA YELLOW WHITE AMBER No function No function No function No function No function AUTO Automatic color change at 100% PATTERN / RED Next / Last Pattern or Increase / Decrease the light intensity of red. SPEED / GREEN Increase / Decrease the speed or Increase / Decrease the light intensity of green. FADE / BLUE Increase / Decrease the fade time or Increase / Decrease the light intensity of blue BRIGHTNESS Dimmer 0-100% UNIT SETTING ON / OFF All settings were set by the dipswitches. On / Off switch 9 / 12
5. Technical data Power supply Voltage 12-24V DC, 6,5 A max. Connections Strom out XLR in/out 350 / 700 ma Terminal Controlling Sound-to-Light Automatic DMX512 Number of channels No Yes Yes 3 (RGB) Hardware Dimension Weight 115 x 54 x 23 mm 0,15 kg 10 / 12
11 / 12
Importer: B & K Braun GmbH Industriestraße 2 D-76307 Karlsbad www.bkbraun.com info@bkbraun.com 12 / 12