Deutsche Akkreditierungsstelle GmbH Annex to the Accreditation Certificate D-PL-17819-01-00 according to DIN EN ISO/IEC 17025:2005 Period of validity: 11.08.2014 to 10.08.2019 Holder of certificate: MPA Dresden GmbH Fuchsmühlenweg 6F, 09599 Freiberg Tests in the fields: Testing of portable fire extinguishers, mobile fire extinguishers without own power operation and fire extinguishers fixed in vehicles, fire extinguishers for controlling pulverised lignite and smouldering fire; testing of fire extinguishing sprays; Testing of fire extinguishing agents; fire tests of building materials, building components and, roofing, cables and insulated lines, safety storage cabinets, upholstered furniture and upholstery composites, textiles, and bedding, as well as testing of fire behaviour under actual fire conditions, fire tests in the area of maritime transport and railway vehicles; Testing of and testing of fire behaviour, fire resistance and behaviour of in the event of external fire within the framework of (EU) Regulation no. 05/2011 for specification of harmonised conditions for the marketing of (Construction Products Regulation) Abbreviations used: see last page The testing laboratory is permitted, without being required to inform and obtain prior approval from DAkkS, to use standard testing methods listed here with different issue dates. This document is a translation. The definitive version is the original German annex to the accreditation certificate. 1/40
1 Fire extinguishers (except testings according to directive 97/2/EG) 1 1.1 Portable fire extinguishers DIN EN -7 2007-10 Portable fire extinguishers - Part 7: Characteristics, extinguishing performance, requirements and testing in conjunction with: DIN EN -10:2010-0 Portable fire extinguishers - Part 10: Guidelines for certifying the conformity of a portable fire extinguisher to EN -7 DIN EN -8 2007-02 Corrigendum 1 2008-01 DIN EN -9 2007-02 Corrigendum 1 2008-01 Portable fire extinguishers - Part 8: Additional specifications of EN -7 regarding structural design, resistance to pressure and mechanical testing of portable extinguishers with a maximum allowable pressure equal to or lower than 0 bar Portable fire extinguishers - Part 9: Additional requirements of EN -7 for pressure resistance of carbon dioxide fire extinguishers 1.2 Mobile fire extinguishers without own power operation DIN EN 1866-1 2007-10 Corrigendum 1 2008-01 E DIN EN 1866-2 2014-07 DIN EN 1866-201-08 Mobile fire extinguishers - Part 1: Characteristics, performance and test methods, Corrigenda to DIN EN 1866-1:2007-10 Mobile fire extinguishers - Part 2: Additional specifications of EN 1866-1 regarding structural design, resistance to pressure and mechanical testing of extinguishers with a maximum pressure equal to or lower than 0 bar Mobile fire extinguishers - Part : Additional specifications of EN 1866-1 regarding pressure resistance of carbon dioxide fire extinguishers 1 Directive 97/2/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment Period of validity: 11.08.2014 to 10.08.2019 - Translation - 2/40
1. Other fire extinguishers LG-01 1996-11 Suitability testing of fire extinguishers for controlling pulverised lignite and smouldering fire 1.4 Fire extinguishing sprays EK5/TA7 1-12:201 DIN SPEC 14411 201-07 NF S61-804 1998-10 BS 6165 2002-02 Guideline for testing and certification of fire extinguishers of the aerosol type (GS) Extinguishing aerosol dispenser Générateurs d aérosol à fonction extinctrice Specification for small disposable fire extinguishers of the aerosol type 2 Fire extinguishing agents DIN EN 615 2009-08 ISO 7202 2012-07 DIN EN 1568-1 2008-06 Corrigendum 1 2010-07 DIN EN 1568-2 2008-06 Corrigendum 1 2010-07 DIN EN 1568-2008-06 Corrigendum 1 2010-07 Fire protection - fire extinguishing agents - specifications for powders (other than class D powders) Fire protection - Fire extinguishing agents - Powder Fire protection - Fire extinguishing agents - Powder Fire extinguishing agents - Foam concentrates - Part 1: Specification for the production of medium expansion foam concentrates for surface application on water-immiscible liquids Corrigendum to DIN EN 1568-1:2008-06 Fire extinguishing agents - Foam concentrates - Part 2: Specifications for the production of high-expansion foam concentrates for surface application on water-immiscible liquids Corrigendum to DIN EN 1568-2:2008-06 Fire extinguishing agents - Foam concentrates - Part : Specifications for the production of low-expansion foam concentrates for surface application on water-immiscible liquids Corrigendum to DIN EN 1568-:2008-06 Period of validity: 11.08.2014 to 10.08.2019 - Translation - /40
DIN EN 1568-4 2008-06 Corrigendum 1 2010-07 DIN EN 1869 2001-01 ICAO Airport Service Manual part1 appendix 8 E 2004-05 IMO MSC/Circ. 798 1997-06 IMO MSC/Circ. 670 1995-01 IMO MSC.1/Circ. 112 2009-06 ISO 720-1 2011-06 ISO 720-2 2011-06 ISO 720-2011-08 Fire extinguishing agents - Foam concentrates - Part 4: Specifications for the production of low-expansion foam concentrates for surface application on water-miscible liquids Corrigendum to DIN EN 1568-4:2008-06 Fire blankets Availability of Extinguishing Media - Specification, Procedures and Performance Levels Guidelines for the performance and testing criteria and surveys of medium - expansion foam concentrates for fixed fire - extinguishing systems Guidelines for the performance and testing criteria and surveys of high - expansion foam concentrates for fixed fire - extinguishing systems Revised guidelines for the performance and testing criteria and surveys of foam concentrates for fixed fire-extinguishing systems Fire extinguishing agents - Foam concentrates - Part 1: Specifications for the production of low-expansion foam concentrates Fire extinguishing agents - Foam concentrates - Part 2: Specifications for the production of medium and high-expansion foam concentrates Fire extinguishing agents - Foam concentrates - Part : Specifications for the production of low-expansion foam concentrates for surface application on water-miscible liquids Period of validity: 11.08.2014 to 10.08.2019 - Translation - 4/40
further applicable documents: LM 01-01 2011-12 Testing of aqueous fire extinguishing agents (contains: EN 1568, Ch. 6: ph-value EN 1568, Ch. 5: viscosity EN DIN 14 272, Ch. 5.5: density EN 1568, Ch. 4: sediment EN DIN 14272, Ch. 5.2: ageing EN ISO 5764, freezing point EN -7, testings in combination with FL) Fire tests on building components and, as well as safety storage cabinets, cables and insulated cables; testing of fire behaviour under actual fire conditions.1 Building materials, building components and DIN 4102-1 1998-05 DIN 4102-2 1977-09 DIN 4102-1977-09 DIN 4102-5 1977-09 DIN 4102-7 1998-07 DIN 4102-8 200-10 DIN 4102-9 1990-05 Fire behaviour of building materials and building components - Part 1: Building material - definitions, requirements and testing Fire behaviour of building materials and building components - Part 2: Building components - definitions, requirements and testing Fire behaviour of building materials and building components - Part : Fire walls and non-load-bearing external walls - definitions, requirements and testing Fire behaviour of building materials and building components - Part 5: Fire shutters, shutters in elevator shaft walls and around fire-resistant glazings - definitions, requirements and testing Fire behaviour of building materials and building components - Part 7: Roofing - definitions, requirements and testing Fire behaviour of building materials and building components - Part 8: Small scale test furnace Fire behaviour of building materials and building components - Part 9: Cable penetration seals - definitions, requirements and testing Period of validity: 11.08.2014 to 10.08.2019 - Translation - 5/40
DIN 4102-11 1985-12 DIN 4102-12 1998-11 DIN 4102-1 1990-05 DIN 4102-15 1990-05 DIN 4102-16 1998-05 DIN 4102-17 1990-12 DIN 18089-1 1984-01 DIN EN 16-1 1999-10 DIN EN 16-1 2012-10 DIN EN 16-2 1999-10 DIN EN 164-1 1999-10 DIN EN 164-2 1999-10 DIN EN 164-2014-05 Fire behaviour of building materials and building components - Part 11: Pipe encasements, pipe sealing, service shafts and ducts, and inspection chamber shutters; definitions, requirements and testing Fire behaviour of building materials and building components - Part 12: Functional integrity of electric cable systems - requirements and testing Fire behaviour of building materials and building components - Part 1: Fire-resistant glazings - definitions, requirements and testing Testing of fire behaviour of building materials and building components - Part 15: Brandschacht [fire shaft] Fire behaviour of building materials and building components - Part 16: Performing "Brandschacht" tests Fire behaviour of building materials and building components - Part 17: Determination of melting point of mineral fibre insulating materials - definitions, requirements and testing Fire shutters, fillers for fire-doors - mineral fibreboards (felts) - definitions, descriptions, requirements, testing Fire resistance tests - Part 1: General requirements Fire resistance tests - Part 1: General requirements Fire resistance tests - Part 2: Alternative and additional methods Fire resistance tests on non-load-bearing building components - Part 1: Walls Fire resistance tests on non-load-bearing building components - Part 2: Suspended ceilings Fire resistance tests on non-load-bearing building components - Part : Curtain walls - Overall execution Period of validity: 11.08.2014 to 10.08.2019 - Translation - 6/40
DIN EN 164-4 2007-06 DIN EN 165-1 201-08 DIN EN 165-2 2000-02 DIN EN 166-1 1999-10 DIN EN 166-2009-07 DIN EN 166-4 2010-08 DIN EN 166-5 2010-06 DIN EN 166-6 2005-02 DIN EN 166-7 2004-09 E DIN EN 166-11 2010-11 E DIN EN 166-12 2010-11 DIN EN 1415 2004-11 DIN EN 164-1 2014-0 DIN EN 182 2010-12 Fire resistance tests on non-load-bearing building components - Part 4: Curtain walls - Partial execution Fire resistance tests for loadbearing elements - Part 1: Walls Fire resistance tests for loadbearing elements- Part 2: Floors and roofs Fire resistance tests on service installations - Part 1: Ducts Fire resistance tests on service installations - Part : Penetration seals Fire resistance tests on service installations - Part 4: Linear joint seals Fire resistance tests on service installations - Part 5: Service ducts and shafts Fire resistance tests on service installations - Part 6: Raised access and hollow core floors Fire resistance tests on service installations - Part 7: Conveyor systems and their shutters Fire resistance tests on service installations - Part 11: Functional integrity of electrical cable systems with fire-protection system Fire resistance tests on service installations - Part 12: Fireprotection seal for ventilation ducts Fire-protection linings - Determination of fire protection ability Fire resistance and smoke control tests on doors, gates, shutters, windows and building hardware - Part 1: Fire resistance tests on doors, gates, shutters and windows Fire behaviour tests on - Construction products excluding floorings exposed to the thermal attack by a single burning item Period of validity: 11.08.2014 to 10.08.2019 - Translation - 7/40
DIN EN ISO 1716 2010-11 DIN EN ISO 1182 2010-10 DIN EN ISO 7840 201-12 DIN EN ISO 929-1 2010-11 DIN EN ISO 11925-2 2011-02 DIN V ENV 1187 2006-10 DIN CEN/ TS 1187 DIN SPEC 91187 2012-0 DIN EN 1501-1 DIN EN 1501-2 2010-02 DIN EN 1501-2010-02 DIN EN 1501-4 DIN EN 1501-5 Fire behaviour tests on - Determination of heat of combustion Reaction to fire tests for products Determination of the gross heat combustion Small craft - Fire-resistant fuel hoses Fire behaviour tests on floor coverings - Part 1: Determination of fire behaviour when subjected to a heat radiator Reaction to fire tests Ignitability of products subjected to direct impingement of flame Part 2: Single-flame source test Test method for exposure of roofing to external fires - Method 1: and building types as per their fire behaviour - Part 1: Classification using results from fire behaviour tests on and building types as per their fire behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests and building types as per their fire behaviour - Part : Classification using results from fireresistance tests on components of HVAC systems: Fire-resistant ducts and fire dampers and building types as per their fire behaviour - Part 4: Classification using results from fireresistance tests on smoke control systems and building types as per their fire behaviour - Part 5: Classification using results from tests on roofing exposed to external fire Period of validity: 11.08.2014 to 10.08.2019 - Translation - 8/40
E DIN EN 1501-6 2011-11 UL 790 22-04-2004 Fire classification of and building elements - Part 6: Classification using data from reaction to fire tests on electric cables Standard test methods for fire tests on roof covering in conjunction with: UL 170:2002-0 Flat-Plate Photovoltaic Modules and Panels EN 6170-2 2012-09 IMO FTP Code 2010 Photovoltaic (PV) module safety qualification - Part 2: Requirements for testing - Fire Test MST 2 International code for application of fire test procedures (2010 FTP Code), MSC.07 (88) IMO FTP Code Part 1 Non-combustibility test as per ISO 1182 IMO FTP Code Part 2 IMO FTP Code Part IMO FTP Code Part 4 Smoke and toxicity test as per ISO 5659-2 + resolution A.65(16), A.687(17), A.75(18) Testing for classification into classes A, B and F - as per A.754(18) Testing of (emergency) fire door control systems IMO FTP Code Part 5 Testing of surface flammability as per A.65(16) + ISO 1716 IMO FTP Code Part 7 IMO FTP Code Part 8 Testing of vertically supported textiles and films as per A.471(XII) and A.56(14) Testing of upholstered furniture as per A.652(16) IMO FTP Code Part 9 Testing of mattresses and upholstered bed bases as per A.688 (17).2 Cables and insulated lines DIN EN 50266-2-1 2001-09 General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-1: Testing methods - testing type A F/R Period of validity: 11.08.2014 to 10.08.2019 - Translation - 9/40
DIN EN 50266-2-2 2001-09 DIN EN 50266-2- 2001-09 DIN EN 50266-2-4 2001-09 DIN EN 50266-2-5 2001-09 DIN EN 5005; point 9.1 (VDE 260-05:200-0) 200-0 DIN EN 5099 (VDE 0482-99) 2012-02 DIN EN 602-1-2 (VDE 0482-2-1-2) 2005-06 DIN EN 602-1- (VDE 0482-2-1-) 2005-06 DIN EN 602-2-2 (VDE 0482-2-1-) 2005-06 General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-2: Testing methods - testing type A General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-: Testing methods - testing type B General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-4: Testing methods - Thin cables, testing type C General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-5: Thin cables, testing type D Railway applications - Railway rolling stock cables and lines with improved fire behaviour - Testing methods General testing methods for behaviour of wires and insulated cables under fire conditions - Heat release and smoke production measurement on cables during flame spread test - Testing apparatus, methods and results Testing of cables, insulated lines and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame spread for a single wire, insulated line or cable - Testing method with 1 kw pre-mixed flame (IEC 602-1-2:2004) Testing of cables, insulated lines and optical fibre cables under fire conditions - Part 1-: Test for vertical flame spread for a single wire, insulated line or cable - Testing method for evaluation of flaming droplets/particles (IEC 602-1-:2004) Testing of cables, insulated lines and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame spread for a single wire, insulated line or cable - Testing method with diffusion flame (IEC 602-1-2:2004) Period of validity: 11.08.2014 to 10.08.2019 - Translation - 10/40
DIN EN 6104-2 (VDE 0482-104-2) 2006-0 IEC 601-21 1999-04 DIN EN 602--21: (VDE 0482-2--21) : 2010-08 DIN EN 602--22: (VDE 0482-2--22) : 2010-08 DIN EN 602--2: 2010-08 DIN EN 602--24: 2010-08 DIN EN 602--25: 2010-08 UIC 564-2, Annex 9 1991-01 General testing methods for behaviour of wires and insulated cables under fire conditions - Measurement of smoke density of cables and insulated lines burning under defined conditions - Part 2: Testing method Tests for electric cables under fire conditions Circuit integrity Part 21: Procedures and requirements - -Cables of rated voltage up to and including 0,6/1,0 kv Testing of cables and insulated lines under fire conditions - Part -21: Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Testing type A F/R Testing of cables, insulated lines and optical fibre cables under fire conditions - Part -22: Testing of vertical flame spread of verticallymounted bundles of cables and insulated lines - Testing type A Testing of cables, insulated lines and optical fibre cables under fire conditions - Part -2: Testing of vertical flame spread of verticallymounted bundles of cables and insulated lines - Testing type B Testing of cables, insulated lines and optical fibre cables under fire conditions - Part -24: Testing of vertical flame spread of verticallymounted bundles of cables and insulated lines - Testing type C Testing of cables, insulated lines and optical fibre cables under fire conditions - Part -25: Testing of vertical flame spread of verticallymounted bundles of cables and insulated lines - Testing type D Testing method for determining the reaction of electrical lines on fire in conjunction with: UIC 895, Annex 6 1976-07 Testing of flame resistance, testing methods BS 685 tab. 1+14 And Annex D 8.7 1999-01 DIN EN 50267-2-1 (VDE 0482-267-2-1) 1999-04 Code of practice for fire precautions in the design and construction of passenger carrying trains - Flame spread - Measurement of smoke density of cables General testing methods for behaviour of wires and insulated cables under fire conditions - Testing of gases produced during combustion of materials in cables and insulated lines - Part 2-1: Testing methods - determination of the amount of halogen hydracid Period of validity: 11.08.2014 to 10.08.2019 - Translation - 11/40
DIN EN 50267-2-2 (VDE 0482-267-2-2) 1999-04 DIN EN 50267-2- (VDE 0482-267-2-) 1999-04 DIN EN 50200 (VDE 0482-200) 2007-0 DIN EN 6049-2 Section 8.2.14: 2006-07 IEC 601-2 1999-04 General testing methods for behaviour of wires and insulated cables under fire conditions - Testing of gases produced during combustion of materials in cables and insulated lines - Part 2-2: Testing methods - determination of degree of acidity of gases released from these materials by measuring ph and conductivity General testing methods for behaviour of wires and insulated cables under fire conditions - Testing of gases produced during combustion of materials in cables and insulated lines - Part 2-: Testing methods - determination of degree of acidity of important materials in cables by calculating the weighted average of ph and conductivity Testing of insulation integrity of exposed small cables used in emergency circuits under fire conditions Low-voltage switchgear assemblies - Part 2: Particular requirements for busbar trunking systems (busways) Section 8.2.14 Verification of resistance to fire propagation Testing of electric cables under fire conditions - Functional integrity - Methods and requirements - Electric data cables. Safety storage cabinets DIN EN 14470-1 2004-07 DIN EN 14470-2 2006-11 DIN EN 1047-1 2006-01 DIN EN 1047-2 201-05 DIN EN 15659 2009-12 DIN EN 14727 2006-0 Fire-resistant storage cabinets - Part 1 Safety storage cabinets for flammable liquids Fire-resistant storage cabinets - Part 2 Safety storage cabinets for pressurised gas cylinders Secure storage units - Classification and methods of testing resistance to fire - Part 1: Data cabinets and diskette inserts Secure storage units - Classification and methods of testing resistance to fire - Part 2: Data security spaces and containers Secure storage units - Classification and methods of testing resistance to fire - Light fire-protection cabinets Laboratory furniture - Storage units for laboratories - Requirements and testing methods Period of validity: 11.08.2014 to 10.08.2019 - Translation - 12/40
EK/AK4 09-10: 2009-12 Revised guideline for testing and certification of safety storage cabinets within the framework of GS-marking.4 Upholstered furniture and upholstery composites, textiles and bedding DIN EN 1021-1 2006-04 DIN EN 1021-2 2006-04 DIN EN 597-1 1995-01 DIN EN 597-2 1995-01 DIN 5441 1988-01 DIN 5487 2007-12 DIN 66084 200-07 DIN EN ISO 12952-1 2011-01 DIN EN ISO 12952-2 2011-01 DIN EN 145 200-10 Furniture - Assessment of the ignitability of upholstered furniture - Part 1: Ignition source - smouldering cigarette Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source - a gas flame equivalent to a burning match Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 1: Ignition source - smouldering cigarette Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 2: Ignition source - a gas flame equivalent to a burning match Testing of seats in railway vehicles for public transport; determination of burning behaviour with a paper pillow as ignition source Testing of materials, small components and component sections in railway vehicles - Determination of burning behaviour using a gas burner (wide-slot burner test) Classification of burning behaviour of upholstery composites Textiles - Assessment of the ignitability of bedding items - Part 1: Ignition source - smouldering cigarette (ISO 12952-1:2010) Textiles - Assessment of the ignitability of bedding items - Part 2: Ignition source - match-flame equivalent (ISO 12952-2:2010) Textiles and textile products - Burning behaviour of bedding items - Classification scheme.5 Construction products DIBt 2010-04 Approval guidelines for used for producing ablation coatings Period of validity: 11.08.2014 to 10.08.2019 - Translation - 1/40
DIBt 2011/1 Approval guidelines for that are used as flame-proof materials in building components and building types.6 Railway applications EN 45545-2 201-08 Railway applications - Fire protection in railway vehicles - Part 2: Requirements for fire behaviour of materials and components with reference to EN ISO 11925-2 2010 EN ISO 929-1 2010 EN ISO 1182 2010 EN ISO 1716 2010 EN 1501-1 2007 + A1:2009 EN 5005 200-0 EN 602-1-2 2005-06 EN 6104-2 2006-0 Fire behaviour tests on construction products - Part 2: Ignitability of products subjected to direct impingement of flame Fire behaviour tests on floor coverings - Part 1: Determination of fire behaviour when subjected to a heat radiator Fire behaviour tests on products - Non-combustibility test Fire behaviour tests on products - Determination of heat of combustion (calorific value) behaviour - Part 1: Classification using Railway applications - Railway rolling stock cables and lines with improved fire behaviour - Testing methods (9.1.2 Flame spread) Testing of cables, insulated lines and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame spread for a single wire, insulated line or cable - Testing method with 1 kw pre-mixed flame General testing methods for behaviour of wires and insulated cables under fire conditions - Measurement of smoke density of cables and insulated lines burning under defined conditions - Part 2: Testing method Period of validity: 11.08.2014 to 10.08.2019 - Translation - 14/40
EN ISO 12952-2 2011-01 Textiles - Assessment of the ignitability of bedding items - Part 2: Ignition source - match-flame equivalent EN 45545-201-08 Railway applications - Fire protection in railway vehicles - Part : Fire resistance of fire shutters with reference to EN 16-1 2012-10 Fire resistance tests - Part 1: General requirements EN 164-1 1999 EN 165-2 1999 EN 164-1 2014-0 EN 1501-2 2007+A1:2009 EN ISO 1182 2010 EN ISO 1716 2010 ISO 84-1 1999-09 Fire resistance tests on non-loadbearing building components - Part 1: Walls Fire resistance tests on load-bearing building components - Part 2: Ceilings and roofs Fire resistance tests on non-loadbearing building components - Part 1: Walls behaviour - Part 2: Classification using results from fire-resistance tests, excluding ventilation systems Fire behaviour tests on products - Non-combustibility test Fire behaviour tests on products - Determination of heat of combustion (calorific value) Fire resistance tests - Building components - Part 1 General requirements DIN 5510-2 2009-05 Preventive fire protection in railway vehicles - Part 2: Fire behaviour and fire side-effects of materials and components - Classification, requirements and testing methods with reference to Period of validity: 11.08.2014 to 10.08.2019 - Translation - 15/40
DIN 4102-1 1998-05 DIN 4102-8 200-10 DIN 548-1 1984-06 DIN 548-2 1984-06 DIN 548-1984-06 DIN 5441 1988-01 DIN 5487 2007-12 DIN EN 597-1 1995-01 DIN EN 597-2 1995-01 DIN EN 1021-1 2006-04 Fire behaviour of building materials and building components - Part 1: Building material - definitions, requirements and testing Fire behaviour of building materials and building components - Part 8: Small scale test furnace Testing of combustible materials; response to ignition by a small flame; general data Testing of combustible materials; response to ignition by a small flame; edge ignition Testing of combustible materials; response to ignition by a small flame; surface ignition Testing of seats in railway vehicles for public transport - determination of burning behaviour with a paper pillow as ignition source Testing of materials, small components and component sections in railway vehicles - Determination of burning behaviour using a gas burner (wide-slot burner test) Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 1: Ignition source - smouldering cigarette Furniture - Assessment of the ignitability of mattresses and upholstered bed bases - Part 2: Ignition source - a gas flame equivalent to a burning match Furniture - Assessment of the ignitability of upholstered furniture - Part 1: Ignition source - smouldering cigarette Period of validity: 11.08.2014 to 10.08.2019 - Translation - 16/40
DIN EN 1021-2 2006-04 DIN EN 1501-1 DIN EN 1501-2 Furniture - Assessment of the ignitability of upholstered furniture - Part 2: Ignition source - a gas flame equivalent to a burning match behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests DIN EN 50266-2-4 2001-09 DIN EN 50266-2-5 2001-09 DIN EN 5005 200-0 DIN EN 602-1-2 2005-06 DIN EN 602-2-2 2005-06 General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-4: Testing methods - testing type C General testing methods for cables and insulated lines under fire conditions - Testing of vertical flame spread of vertically-mounted bundles of cables and insulated lines - Part 2-5: Testing methods - thin cables, testing type D Railway applications - Railway rolling stock cables and lines with improved fire behaviour - Testing methods Testing of cables, insulated lines and optical fibre cables under fire conditions - Part 1-2: Test for vertical flame spread for a single wire, insulated line or cable - Testing method with 1 kw pre-mixed flame Testing of cables, insulated lines and optical fibre cables under fire conditions - Part 2-2: Test for vertical flame spread for a single wire, insulated line or cable - Testing method with diffusion flame Period of validity: 11.08.2014 to 10.08.2019 - Translation - 17/40
DIN EN 6104-2 2006-0 DIN EN ISO 929-1 2010-11 DIN 5510-2 2009-05 Measurement of smoke density of cables and insulated lines burning under defined conditions - Part 2: Testing methods and requirements Fire behaviour tests on floor coverings - Part 1: Determination of fire behaviour when subjected to a heat radiator Preventive fire protection in railway vehicles - Part 2: Fire behaviour and fire side effects of materials and parts - Classification, requirements and test methods annex A: Testing of seats in railway vehicles (seat cushion test).7 Fire protection products (ETAG) ETAG 018/1 2004-11 Guideline for the European technical approval for fire protection products - Part 1: General information DIN EN 1501-1 DIN EN 1501-2 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests ETAG 018/2 2006-06 Guideline for the European technical approval for fire protection products - Part 2: Reactive fire protection coatings on steel components DIN EN 1501-1 Period of validity: 11.08.2014 to 10.08.2019 - Translation - 18/40
DIN EN 1501-2 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests ETAG 018/ 2006-01 Guideline for the European technical approval for fire protection products - Part : Fire protection linings with or without lathing as well as fire protection lining kits for fire protection applications DIN EN 1501-1 DIN EN 1501-2 DIN EN 1501-2010-02 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests behaviour - Part : Classification using results from fire-resistance tests on components of HVAC systems: Fireresistant ducts and fire dampers ETAG 018/4 2004-11 Guideline for the European technical approval for fire protection products - Part 4: Products and kits made of formable and nonformable fire protection boards and mats DIN EN 1501-1 ETAG 004 2011-08 Guideline for European technical approval for external thermal insulation composite systems with rendering Period of validity: 11.08.2014 to 10.08.2019 - Translation - 19/40
DIN EN 1501-1 ETAG 005 2004-0 Guideline for the European technical approval for liquid applied roof waterproofing kits - Parts 1-8 DIN EN 1501-1 DIN EN 1501-5 behaviour - Part 5: Classification using results from tests on roofing exposed to external fire ETAG 007 2001-04 Guideline for the European technical approval for timber frame building kits DIN EN 1501-1 ETAG 010 2002-09 Guideline for the European technical approval for self-supporting translucent roof kits DIN EN 1501-1 Period of validity: 11.08.2014 to 10.08.2019 - Translation - 20/40
DIN EN 1501-5 behaviour - Part 5: Classification using results from tests on roofing exposed to external fire ETAG 011 2002-01 Guideline for the European technical approval for light composite wood-based beams and columns DIN EN 1501-1 ETAG 012 2002-06 Guideline for the European technical approval for log building kits DIN EN 1501-1 ETAG 016/1 200-11 Guideline for the European technical approval for self-supporting composite light-weight panels - Part 1: General information DIN EN 1501-1 ETAG 016/2 200-11 Guideline for the European technical approval for self-supporting composite light-weight panels - Part 2: Specific aspects relating to self-supporting composite light-weight panels for use in roofs Period of validity: 11.08.2014 to 10.08.2019 - Translation - 21/40
DIN EN 1501-1 ETAG 016/ 2005-02 Guideline for the European technical approval for self-supporting composite light-weight panels - Part : Specific aspects relating to self-supporting composite light-weight panels for use in external walls and linings DIN EN 1501-1 ETAG 016/4 2004-07 Guideline for the European technical approval for self-supporting composite light-weight panels - Part 4: Specific aspects relating to self-supporting composite light-weight panels for use in internal walls and ceilings DIN EN 1501-1 ETAG 019 2004-11 Guideline for the European technical approval for prefabricated load-bearing panels made of wood and wood-based materials DIN EN 1501-1 DIN EN 1501-5 behaviour - Part 5: Classification using results from tests on roofing exposed to external fire Period of validity: 11.08.2014 to 10.08.2019 - Translation - 22/40
ETAG 022/1 2007-04 Guideline for the European technical approval for kits for waterproofing systems for walls and floorings in wet areas - Part 1: Liquid applied waterproofing with or without wearing surface DIN EN 1501-1 ETAG 022/2 2010-11 Guideline for the European technical approval for kits for waterproofing systems for walls and floorings in wet areas - Part 2: Waterproofing systems with sealing membranes for wet areas DIN EN 1501-1 ETAG 022/ 2010-11 Guideline for the European technical approval for kits for waterproofing systems for walls and floorings in wet areas - Part : Waterproofing systems with watertight boards for wet areas DIN EN 1501-1 ETAG 024 2006-01 Guideline for the European technical approval for concrete kits for construction of load-bearing building structures DIN EN 1501-1 Period of validity: 11.08.2014 to 10.08.2019 - Translation - 2/40
DIN EN 1501-2 DIN EN 1501-5 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests behaviour - Part 5: Classification using results from tests on roofing exposed to external fire ETAG 026/1 2008-01 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire - Part 1: General information DIN EN 1501-1 DIN EN 1501-2 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests ETAG 026/2 2011-08 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire - Part 2: Penetration seals DIN EN 1501-1 DIN EN 1501-2 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests Period of validity: 11.08.2014 to 10.08.2019 - Translation - 24/40
ETAG 026/ 2011-08 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire - Part : Linear joint seals and fire barriers DIN EN 1501-1 DIN EN 1501-2 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests ETAG 026/5 2011-02 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire - Part 5: Fire barriers DIN EN 1501-1 DIN EN 1501-2 behaviour, excluding ventilation systems - Part 2: Classification using results from the fire-resistance tests Period of validity: 11.08.2014 to 10.08.2019 - Translation - 25/40
4 Testing of and testing of fire behaviour, fire resistance and behaviour of in the event of external fire within the framework of (EU) Regulation no. 05/2011 for specification of harmonised conditions for the marketing of (Construction Products Regulation) Decision / Ruling of the Commission System 1) Technical specification 1995/467/EG Gypsum products EN 1658-1:2005 Metal lath and beads - Definitions, requirements and testing methods - Part 1: Internal plastering EN 1658-2:2005 Metal lath and beads - Definitions, requirements and testing methods - Part 2: Exterior plastering EN 1815:2006 Moulded components made of fibre-reinforced gypsum - Definitions, requirements and testing methods EN 1950:2005 Gypsum plasterboard thermal/acoustic insulation composite panels - Definitions, requirements and testing methods EN 196:2005/AC:2006 Sealing materials for Gypsum plasterboard joints - Definitions, requirements and testing methods EN 14190:2005 Gypsum plasterboard products from reprocessing - Definitions, requirements and testing methods EN 14209:2005 Preformed plasterboard cornices - Definitions, requirements and testing methods EN 14496:2005 Gypsum based adhesives for thermal/acoustic insulation composite panels and plasterboards - Definitions, requirements and testing methods EN 520:2004+A1:2009 Gypsum plasterboards - Definitions, requirements and testing methods EN 12859:2011 Gypsum wallboards - Definitions, requirements and testing methods EN 12860:2001/AC:2002 Gypsum based adhesives for gypsum wallboards - Definitions, requirements and testing methods Period of validity: 11.08.2014 to 10.08.2019 - Translation - 26/40
Decision / Ruling of the Commission System 1) Technical specification 1995/467/EG Gypsum products 1996/580/EG Curtain wall kits 1997/176/EG Structural timber and timber fasteners 1997/462/EG Wood-based materials 1997/808/EG Floor coverings EN 1279-1:2008 Gypsum binders and gypsum dry mortar - Part 1: Definitions and requirements EN 14195:2005/AC:2006 Metal framing components for gypsum plasterboard systems - Definitions, requirements and testing methods EN 14246:2006/AC:2007 Gypsum elements for suspended ceilings - Definitions, requirements and testing methods EN 180:200 Curtain walls - Product standard EN 1474:2004 Timber structures - Structural laminated veneer lumber - Requirements EN 1986:2004 Wood-based panels for use in construction - Characteristics, evaluation of conformity and marking EN 14041:2004/AC:2006 Resilient, textile and laminate floor coverings - Important characteristics EN 1442:2005+A1:2008 Parquet and wooden floorings - Characteristics, evaluation of conformity and marking EN 14904:2006 Surfaces for sports areas - Indoor surfaces for multi-sports use - Requirements EN 1454-1:2004 Calcium sulphate binders, composite binders and ready-mixed mortar for floor screeds - Part 1: Definitions and requirements 1998/21/EG Partition kits EN 181:2002 Floor screed mortar, screed materials and floor screeds - Characteristics and requirements for floor screed mortar and screed materials EN 14016-1:2004 Binders for magnesite screeds - Caustic magnesia and magnesium chloride - Part 1: Definitions and requirements ETAG 00 Guideline for European technical approval for internal partition kits for use as non-load-bearing walls Period of validity: 11.08.2014 to 10.08.2019 - Translation - 27/40
Decision / Ruling of the Commission System 1) Technical specification 1998/46/EG Roof coverings, skylights, roof windows and ancillary components 1998/46/EG Roof coverings, rooflights, roof windows and ancillary products for purposes subject to guidelines on fire resistance (i.e. building fire compartments) EN 1496:2006 Roof coverings - Continuous rooflights made of plastic with or without upstands - Classification, requirements and testing methods EN 187:2005 Prefabricated ancillary components for roofing - Individual domed rooflights made of plastic - Product specifications and testing methods EN 104:2005 Clay roofing and shaped tiles - Definitions and product specifications EN 490:2011 Concrete roofing and shaped tiles for roof covering and wall panelling - Product specifications EN 492:2012 Fibre cement roof panels and corresponding shaped tiles - Product specification and test methods EN 14509:2006/AC:2008 Self-supporting double-skin metal-faced insulating panels - Factory-made products - Specifications EN 494:2012 Fibre cement corrugated panels and corresponding shaped tiles - Product specification and testing methods EN 54:2006+A1:2010 Corrugated bitumen sheets - Product specifications and testing methods EN 544:2011 Bitumen shingles with mineral and/or synthetic reinforcements - Product specification and testing methods EN 104:2005 Clay roofing and shaped tiles - Definitions and product specifications EN 187:2005 Prefabricated ancillary components for roofing - Individual domed rooflights made of plastic - Product specifications and testing methods EN 1226-1:2004 Slate and other stone products for discontinuous roofing and external wall cladding - Part 1: Product specification EN 1707:2004+A2:2009 Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics Period of validity: 11.08.2014 to 10.08.2019 - Translation - 28/40
Decision / Ruling of the Commission System 1) Technical specification 1998/46/EG Roof coverings, rooflights, roof windows and ancillary products for purposes subject to guidelines on fire resistance (i.e. building fire compartments) 1998/46/EG Roof coverings, skylights, roof windows and ancillary components 1998/47/EG Internal and external wall and ceiling finishes 1998/47/EG Internal and external wall and ceiling finishes EN 1956:2012 Flexible sheets for waterproofing - Plastic and elastomer sheets for roof waterproofing - Definitions and characteristics EN 1451-1:2006+A1:2010 Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doors without characteristics of fire protection and/or smoke tightness EN 14782:2006 Self-supporting sheet metal roofing and wall lining elements for external cladding and internal lining - Product specification and requirements EN 1478:2006 Fully supported sheet metal roofing and wall lining elements for external cladding and internal lining - Product specification and requirements EN 1496: 2006 Roof coverings - Continuous rooflights made of plastic with or without upstands - Classification, requirements and testing methods EN 1615:201 Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in roofs, walls and ceilings - Requirements and test methods EN 14716:2004 Stretched ceilings - Requirements and test methods EN 15102:2007+A1:2012 Decorative wall linings - Roll and panel form EN 1964:2004+A1:2006 Suspended ceilings - Requirements and test methods EN 12467:2012 Fibre cement panels - Product specification and testing methods EN 14509:2006/AC:2008 Self-supporting double-skin metal-faced insulating panels - Factory-made products - Specifications EN 15102:2007+A1:2011 Decorative wall linings - Roll and panel form Period of validity: 11.08.2014 to 10.08.2019 - Translation - 29/40
Decision / Ruling of the Commission System 1) Technical specification 1998/47/EG Internal and external wall and ceiling finishes EN 48-7:2005 High-pressure decorative laminates (HPL) - Sheets based on thermosetting resins (usually called laminates) - Part 7: Compact laminate and HPL composite panels for internal and external wall and ceiling finishes EN 14915:201-12* Solid wood panelling and cladding - Characteristics, evaluation of conformity and marking 1998/47/EG Internal and external wall and ceiling finishes 1998/599/EG Liquid applied roof waterproofing kits 1998/600/EG Self-supporting translucent roofing kits (except glass-based kits) 1999/90/EG Waterproofing sheets EN 54:2006+A1:2010 Corrugated bitumen sheets - Product specifications and testing methods ETAG 005 Guideline for the European technical approval for liquid applied roof waterproofing kits ETAG 010 Guideline for the European technical approval for selfsupporting translucent roof kits EN 1970:2004/A1:2006 Flexible sheets for waterproofing - Bitumen water vapour control layers - Definitions and characteristics EN 1967:2012 Flexible sheets for waterproofing - Plastic and elastomer sheets for building waterproofing against ground moisture and water - Definitions and characteristics EN 1969:2004+A1:2006 Flexible sheets for waterproofing - Bitumen sheets for building waterproofing against ground moisture and water - Definitions and characteristics EN 1707:2004+A2:2009 Flexible sheets for waterproofing - Reinforced bitumen sheets for roof waterproofing - Definitions and characteristics EN 1956:2012 Flexible sheets for waterproofing - Plastic and elastomer sheets for roof waterproofing - Definitions and characteristics Period of validity: 11.08.2014 to 10.08.2019 - Translation - 0/40
Decision / Ruling of the Commission System 1) Technical specification EN 1859-1:2010 Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 1: Underlays for discontinuous roofing EN 1984:201 Flexible sheets for waterproofing - Plastic and elastomer water vapour control layers - Definitions and characteristics 1999/90/EG Waterproofing sheets EN 1859-2:2010 Flexible sheets for waterproofing - Definitions and characteristics of underlays - Part 2: Underlays for walls 1999/91/EG Thermal insulation products EN 14909:2012 Flexible sheets for waterproofing - Plastic and elastomer damp proof courses - Definitions and characteristics EN 14967:2006 Flexible sheets for waterproofing - Bitumen damp proof courses - Definitions and characteristics EN 1162:2012 Thermal insulation products for buildings - Factory made mineral wool (MW) products - Specification EN 116:2012 Thermal insulation products for buildings - Factory made expanded polystyrene (EPS) products - Specification EN 1164:2012 Thermal insulation products for buildings - Factory made extruded polystyrene foam (XPS) products - Specification 1999/91/EG Thermal insulation products EN 1165:2012 Thermal insulation products for buildings - Factory made polyurethane (PUR) rigid foam products - Specification EN 1166:2012 Thermal insulation products for buildings - Factory made phenolic foam (PF) products - Specification EN 1167:2012 Thermal insulation products for buildings - Factory made cellular glass (CG) products - Specification Period of validity: 11.08.2014 to 10.08.2019 - Translation - 1/40
Decision / Ruling of the Commission System 1) Technical specification EN 1168:2012 Thermal insulation products for buildings - Factory made wood wool (WW) products - Specification EN 1169:2012 Thermal insulation products for buildings - Factory made expanded perlite board (EPB) products - Specification EN 1170:2012 Thermal insulation products for buildings - Factory made products of expanded cork (ICB) - Specification EN 1171:2012 Thermal insulation products for buildings - Factory made wood fibre (WF) products - Specification 1999/91/EG Thermal insulation products EN 1406-1:2004+AC:2006 Thermal insulation products for buildings - In-situ thermal insulation formed from expanded clay light-weight aggregate products (LWA) - Part 1: Specification for the loose-fill products before installation EN 140:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made mineral wool (MW) products - Specification EN 1404:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made flexible elastomeric foam (FEF) products - Specification EN 1405:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made cellular glass (CG) products - Specification EN 1406:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made calcium silicate (CS) products - Specification Period of validity: 11.08.2014 to 10.08.2019 - Translation - 2/40
Decision / Ruling of the Commission System 1) Technical specification EN 1407:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made extruded polystyrene foam (XPS) products - Specification EN 1408:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made rigid polyurethane foam (PUR) and polyisocyanurate foam (PIR) products - Specification EN 1409:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made expanded polystyrene (EPS) products - Specification 1999/91/EG Thermal insulation products EN 141:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made polyethylene foam (PEF) products - Specification EN 1414:2009+A1:201 Thermal insulation products for building equipment and industrial installations - Factory made phenolic foam (PF) products - Specification EN 1416-1:2004 Thermal insulation products for buildings - In-situ thermal insulation formed from expanded perlite (EP) products - Part 1: Specification for bonded and loose-fill products before installation EN 1417-1:2004 Thermal insulation products for buildings - In-situ thermal insulation formed from exfoliated vermiculite (EV) products - Part 1: Specification for bonded and loose-fill products before installation EN 149:2007 Thermal insulation and light-weight fill products for civil engineering applications - Factory made expanded polystyrene (EPS) products - Specification Period of validity: 11.08.2014 to 10.08.2019 - Translation - /40
Decision / Ruling of the Commission System 1) Technical specification 1999/91/EG Thermal insulation products 1999/9/EG Doors, windows, shutters, blinds, gates and fixtures 1999/454/EG Fire-protection penetration seals and linings 1999/469/EG Products related to concrete, mortar and grout EN 15501:201* Thermal insulation products for building equipment and industrial installations - Factory made expanded perlite (EP) and exfoliated vermiculite (EV) products - Specification EN 1451-1:2006+A1:2010 Windows and doors - Product standard, performance characteristics - Part 1: Windows and external pedestrian doors without characteristics of fire protection and/or smoke tightness ETAG 018-1 Guideline for the European technical approval for fire protection products (fire-protection linings and coatings) Part 1: General information ETAG 018-4 + modification Guideline for the European technical approval for fire protection products (fire-protection linings and coatings) Part 4: Products and kits made of formable and non-formable fire protection boards and mats ETAG 026-1 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire - Part 1: General information ETAG 026-2 version 08/2011 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire -Part 2: Penetration seals ETAG 026 - version 08/2011 Guideline for the European technical approval for fire protection products for sealing and closing joints and openings and for stopping the fire -Part : Linear joint seals and fire barriers EN 1504-2:2004 Products and systems for protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part 2: Surface protection systems for concrete EN 1504-:2005 Products and systems for protection and repair of concrete structures - Definitions, requirements, quality control and evaluation of conformity - Part : Structural and non-structural repair Period of validity: 11.08.2014 to 10.08.2019 - Translation - 4/40