11in Please refer to part numbers when reordering For questions or comments about product: Email: sears@sunjoygroup.com or Call toll-free: 1-866-578-6569 Made in / Hecho en CHINA Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179 See our extensive assortment of outdoor living products on-line at www.sears.com and www.kmart.com USE AND CARE GUIDE Back Painted 32 x32 Fire Pit Caution: Carefully Read Instructions and Procedures for Safe Operation Product Code: D71 M56689 UPC Code: 841057143148 Date of Purchase: / / 17in
Back Painted 32x32 Fire Pit WARNING: For Outdoor Use Only. DANGER If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. If odor continues, keep away from the appliance and immediately call your gas supplier or fire department. Propane tank not included AA battery needed, not included WARNING: Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Read the installation, operating and maintenance instructions thoroughly before installing or servicing this equipment. WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. An LP-cylinder not connected for use should not be stored in the vicinity of this or any other appliance. DANGER CARBON MONOXIDE HAZARD This appliance can produce carbon monoxide which has no odor. Usingitinanenclosedspacecankillyou. Never use this appliance in an enclosed space such as a camper, tent, car or home. This appliance complies with ANSI Z21.97-2014/CSA 2.41-2014, Outdoor Decorative Gas Appliances. 1
Thank you for your purchase! Thank you for your purchase! We are pleased that you have chosen Sears for your outdoor gazebo purchase. We hope that you enjoy the unmatched quality, comfort, and style of your new patio item. Every piece is meticulously considered all the way down to the smallest details, exclusively for you, by our world class design team. We know you have a choice when it comes to your patio gazebo needs, so from our team to yours, thank you for letting us be a part of your outdoors. Table of Contents General information 2 Specification 3 Important safety information and precaution 3-4 Expanded view 5 Parts list 6 Installation 7-10 Location 11 Set up 11 Gas connection 11-12 Operation 12 Leak check 12 Ignite lighting 12-13 Storage and Maintenance 13 Trouble shooting 14 Limited warranty 14 Cleaning and maintenance 15 General Information Clening and Maintenance To enjoy outstanding performance of your appliance for years make sure to perform the following maintenance activities on a regular basis. Keep exterior surfaces clean. Use warm soapy water for cleaning. Never use flammable, corrosive or abrasive cleaners. Clean the holes in the burner using a swab that is moistened with soapy water. Keep the holes unobstructed by using a heavy-duty pipe cleaner. The burner must be dry before normal use. Cleaning period should be 1 year. While washing your unit, be sure to keep the area around the burner and pilot assembly dry at all times. If the gas control is exposed to water in any way, DO NOT try to use it. It must be replaced.after a long break from operation, the unit should be inspected for spiders, spider webs or other insects. Air flow must be unobstructed, Keep controls, Burner and circulating air passageways clean. Signs of possible blockage include: Gas odor with extreme yellow tipping of flame. Table does NOT reach the desired temperature. Table flow is excessively uneven. Table makes popping noises. Spider and insects can nest in burner or orifices. Compressed air may help clear away smaller particles. Please do not return this product to the store. For technical assistance on assembly or replacement parts call Sunjoy Group at 1(866) 578-6569 from 8:00 AM EST to 8:00 PM PST or Email sears@sunjoygroup.com or visit www.sunjoyonline.com to place your order or fax your parts replacement order form together with your purchase receipt to 1 (740) 283-3549 for assistance. Made in China IMPORTANT Please take time to read these instructions thoroughly and follow each step carefully for safe and easy operation. Keep this manual to consumer for installer and consumer future reference/use. We would like to hear from you with any comments or suggestions. In the continental U.S., you can call Sunjoy Toll Free number: 1-866-578-6569 from 8:00 AM EST to 8:00 PM PST Monday to Friday. You can also send us an email to sears@sunjoygroup.com. 2 15
Trouble Shooting PROBLEM OBSERVED POSSIBLE CAUSE CORRECTIVE MEASURES Gas odor Gas leak See If you smell gas: on front cover of manual Check all gas connections Delayed ignition Low gas pressure Check gas supply pressure Clogged or dirty burner Clean burner ports-see manual ports Blocked orifice Spent battery section Check orifice opening Change new battery Incorrect burner flame Incorrect gas supply or pressure Blocked orifice Clogged or dirty burner ports If you want to replace the parts listed, please contact SUNJOY Customer Service Center. Limited Warranty: 14 Check gas supply pressure Check and clean orifice opening Clean burner ports Subject to the conditions set out below, this product is warranted to the original purchaser to be free from defects in workmanship and materials for one (1) year from the date of purchase. Satisfactory proof of the purchase date must be furnished at the time of notification of the defect for any claim under the warranty to be enforceable. This warranty covers all parts found defective in workmanship and/or materials during the warranty period and can be repaired or replaced at the discretion of the manufacturer at no cost to the original purchaser. This warranty will be void if the product has not been assembled, installed or operated according to the instructions, or subjected to abuse, improperly treated, neglected, rusted by exposure to the elements, misused and/or if any repairs, maintenance, or service has been done by an unauthorized person. Returns must be properly packaged and returned to the dealer from whom the product was acquired. The manufacturer, distributor and retailer will not be liable for any incidental or consequential loss or damage arising from the installation or operation of the product and/or the failure of any part for any reason. There are no other express or implied warranties, except for those stipulated herein. This warranty gives specific rights and the original purchaser may have additional rights and remedies in law. This warranty does not cover commercial use. Specification Product name Model NO. Rated Heat Output Fuel Gas Supply Manifold Pressure Orifice Size (diameter) Gas Supply Pressure Imporatnt safety information and precaution Back Painted 32x32 Fire Pit L-DN1737SST-C-T 35,000BTU/HR Propane-LP 20 lb. LP-Gas cylinder 11 Inches W.C. 1.9mm Max.250 PSI When the appliance is for connection to a fixed piping system, the installation must conform with local codes, or in the absences of local codes with the National Fuel Gas Code, ANSI Z223.1/NFPA54; International Fuel Gas Code, Natural Gas and Propane Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable. The LP gas supply cylinder to be used must be: 1-Constructed and marked in accordance with the U.S. Department of Transportation (D.O.T.) Specifications for LP-Gas Cylinders, or the Standard for Cylinders, Spheres and Tubes for transportation of Dangerous Goods and Commission, CAN/CSA-B339 as applicable; 2-Provided with a listed overfilling prevention device; 3-Provided with a cylinder connection device compatible with the connection for the appliance. Always place the appliance on a firm and level surface. Solid fuels shall not be burned in this gas appliance. When using decorative Lava Rocks, use only the lava rocks we provided (INCLUDED). The appliance shall be used only outdoors in a well-ventilated space and shall not be used in a building, garage or any other enclosed area. When in use, keep the appliance area clear and at least 40 inches / 101.6 cm side clearance from combustible materials, gasoline and other flammable liquid and vapors. Do not use the appliance under overhead combustible surfaces. Certain items or materials, when stored under the appliance or nearby, will be subjected to radiant heat and could be damaged. Open the door and inspect the hose assembly and burner prior to each use. If there is evidence of excessive abrasion or wear or if the hose or burner is damaged, it must be replaced by appropriate part from the manufacturer. 3
Imporatnt safety information and precaution Inspect the gas connections of the appliance prior to each use. Do not to operate the unit if there is a gas leak. Have the appliance inspected annually by a qualified service person. The pressure regulator and hose assembly provided with the appliance must be used. The replacement part must be the same as the part specified by manufacturer. The assembly of LP-gas and leak checking please refer to the Gas connection on page 8 and leak Test on page 9. and should stay away to avoid burns or prevent clothing ignition. area of the appliance. be replaced prior to operation. or placed on or near the appliance. Do not use the appliance if any part has been under water. Immediately call a qualified technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water. LP-gas supply cylinder to be used must be constructed and marked in accordance with the specifications for LP-gas cylinders of the U.S. Department of Transportation (DOT). The cylinder supplies system must be arranged for vapor withdrawal and the cylinder must include a collar to protect the cylinder valve. Use only 20 lb / 9 kg LP-Gas cylinders. Do not burn wood or any other materials in this appliance. The appliance must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1/2psi (3.5kPa). That other cylinder may be acceptable for use with the appliance provided they are compatible with the appliance retention means and accompanied by illustration(s) depicting the cylinder mounted to the appliance utilizing the cylinder retention means and the point of contact between the cylinder and the retention means. Properly place the hose out of pathways where people may trip over it or in areas where there may be subject to accidental damage. The burner must be replaced prior to the appliance being put into operation if it is evident that the burner is damaged. The replacement burner must be the same as the part specified by manufacturer. The cleaning of the appliance including the burner, please refer to Clean and Maintenance on page 14-15. 4 Lighting The Burners NOTE: While in use, the burner flame should be mainly blue in appearance with a small amount of yellow. The flame can be identified by the following figure. Warning: Lighting the Fire Pit improperly could lead to an unsafe condition. 7. Press in and turn the control valve knob clockwise to OFF to shut down fireplace. Close the gas cylinder valve when the fireplace is not in use. (CAUTION: Do not kink flexible gas hose. If it is kinked, a gas leak could occur.) Storage and Maintenance To obtain the best performance from your fireplace, you must perform the following storage and maintenance activities on a regular basis: Allow disconnecting and removing the gas cylinder. Store the gas cylinder in a dry, well-ventilated and sheltered area protected from inclement weather and dust, out of the reach of children, and not in a building, garage or any other closed area. The fireplace may be stored indoors only if the cylinder is disconnected and removed. Keep the fireplace area clear and free from combustible materials, gasoline and other flammable vapors and liquids. should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burner, and circulating air passageways of the fireplace be kept clean. To obtain the best performance from your fireplace, you must perform the following storage and maintenance activities on a regular basis: please reassemble it according to the picture on the right to make sure the burner induction tunnel is on and exactly cover the orifice base. It is imperative that the control compartment, burner, and circulating air passageways of the fireplace be kept clean. It is recommended not to disassemble the burner. The fireplace should be inspected annually by a qualified service person. 13
Gas Connection Expanded View Fig 8 Operation: LEAK TEST!!!WARNING!!! Do not use an open flame to check for leaks. Do not smoke during testing. Do not test indoors. A leak check must be performed whenever the gas cylinder is replaced. 1. Make sure the control knob is in the OFF position. 2. Make sure the gas cylinder is correctly and securely connected to the pressure regulator, without over tightening. 3. Turn on the gas cylinder valve. Apply 50% soap and 50% water solution to the gas hose and connections between the control knob and gas cylinder. 4. If something is leaking, you will see bubbles form. In case of leaks, turn off the gas supply, undo the leaking connection, re-connect it and try again. If the leak persists, consult Customer Service Center for assistance. 5. If the connection does not leak, continue to the next step. Lighting The Burners 1. Make sure control valve is OFF. 2. Turn on gas tank valve. 3. Press in and turn control valve knob counterclockwise to LOW to light. See the figure to the right. 4. If burner is lit, continue pressing in the control valve knob for a minute to heat the thermocouple. 5. When control valve knob is released, the burner should be lit. If not, turn control valve knob clockwise to OFF. Wait for 5 minutes then start with step 3 above. 6. Press in and turn control valve knob to desired heat output, LOW ~ HIGH. 12 5
Parts List NO. Description Qty NO. Description Qty A Lid 1 I Armor Plate Screen 1 B Table Top 1 J Ignition Wire 1 C Fire Bowl 1 K Battery Box 1 D1 Leg1 1 L Pressure Regulator 1 D2 Leg2 1 M Thermocouple 1 D3 Leg3 1 N Control Valve 1 D4 Leg4 1 O Control Knob 1 E Side Panel 3 P Corrugated pipe 1 F Shelf 1 Q Burner 1 Location Your Gas appliance must be installed on a flat, stable surface, away from any combustible materials or construction. Set-up Your Gas appliance comes assembled, ready for a Gas connection. 1-Remove the appliance from container box and place it on any level, outdoor, non-combustible surface. NOTE: Do not place this appliance on grass or dirt area. This may prevent proper safety venting. 2-Open the gas door and put the cylinder inside. 3-Unscrew the battery box as shown in Fig 1.Insert the negative electrode side of the battery into the bottom of battery box as shown in Fig 2. Then screw the battery box as shown in Fig 3. G Door 1 R Windshield 1 H1 Lava Rock 1(4KG) Hardware Pack No. Description Qty Image AA M6x15 Bolt 4 BB M6x30 Bolt 20 CC M6x15 Screw 4 DD M6 Washer 28 Fig 1 Fig 2 Fig 3 Note: If the battery of the pulse electronic igniter runs out of power, please replace the new battery as above. Gas Connection 1-Open the door and put the chain and control valve outside. See Fig 4. 2-Put the cylinder into the cylinder rack. See Fig 5. 3-Connect the regulator and the cylinder as per Fig.6. Make sure there is no leakage or damage (please refer to Leak Test on page 9 and the damage checking on page 4). 4-Turn the butterfly nut on the cylinder frame, so that the nut is held against the bottom of the cylinder, to make sure the cylinder can be fixed. See Fig 7. 5-Disconnect the regulator and the cylinder as per Fig.8 EE Wrench 1 If you want to replace the parts listed, please contact Customer Service Center: 1-866-578-6569 6 11
Installation Installation Installation will be much easier with two or more people. Step 8: The Lava Rock (H1) should be put in the bottom of the fire bowl (C) and come up just as high as the fire ring. Step 1 (Fig.1): Attach side panel (E) to legs (D1/D2), tighten through the holes on the legs by bolt (BB) and washer (DD). Step 9: Put the lid (A) on the Table Top (B). Step 2 (Fig. 2): Attach side panel (E) to legs (D3/D4), tighten through the holes on the legs by bolt (BB) and washer (DD). 10 7
Installation Installation Step 3 (Fig.3): Attach shelf (F) to legs (D1/D2/D3/D4) by bolt (BB) and washer (DD), do not tighten at this step. (Note: please make sure the circle on the Shelf (F) close to the Leg (D4)) Step 6 (Fig.6): Put the Table Top (B) and fire bowl (C) upside down, connect them with Bolts (CC) and Washer (DD). Step 4(Fig.4): Attach the back side panel (E) to legs (D1/ D3); Tighten to the legs by bolt (BB) and washer (DD). Tighten all Bolts here. Step 5(Fig.5): attach door (G) to legs (D2/ D4); Tighten to the legs by bolt (BB) and washer (DD). Tighten all Bolts here. 8 Step 7 (Fig.7): Attach table top (B) to the legs by bolt (AA) and washer (DD). (Note: When assembling this step, please follow the direction as the arrow showed. (Note: Before this step, please take out the foam in the carton and put it underneath the table top to avoid surface abrasion.) 9