ASTM Fire Standards Table of Contents

Standard C177 C209 C411 C509 C518 C542 C578 C739 C800 C864 C916 C991 C1014 C1029 C1046 C1055 C1057 C1071 C1130 C1149 C1166 C1288 C1289 C1290 C1396 C1482 C1485 ASTM Fire Standards Table of Contents Title Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus Standard Test Methods for Cellulosic Fiber Insulating Board Standard Test Method for Hot-Surface Performance of High-Temperature Thermal Insulation Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing Material Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus Standard Specification for Lock-Strip Gaskets Standard Specification for Rigid, Cellular Polystyrene Thermal Insulation Standard Specification for Cellulosic Fiber Loose-Fill Thermal Insulation Standard Specification for Fibrous Glass Blanket Insulation (Aircraft Type) Standard Specification for Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and Spacers Standard Specification for Adhesives for Duct Thermal Insulation Standard Specification for Flexible Fibrous Glass Insulation for Metal Buildings Standard Specification for Spray-Applied Mineral Fiber Thermal and Sound Absorbing Insulation Standard Specification for Spray-Applied Rigid Cellular Polyurethane Thermal Insulation Standard Practice for In-Situ Measurement of Heat Flux and Temperature on Building Envelope Components Standard Guide for Heated System Surface Conditions that Produce Contact Burn Injuries Standard Practice for Determination of Skin Contact Temperature from Heated Surfaces Using a Mathematical Model and Thermesthesiometer Standard Specification for Fibrous Glass Duct Lining Insulation (Thermal and Sound Absorbing Material) Standard Practice for Calibrating Thin Heat Flux Transducers Standard Specification for Self-Supported Spray Applied Cellulosic Thermal Insulation Standard Test Method for Flame Propagation of Dense and Cellular Elastomeric Gaskets and Accessories Standard Specification for Discrete Non-Asbestos Fiber-Cement Interior Substrate Sheets Standard Specification for Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board Standard Specification for Flexible Fibrous Glass Blanket Insulation Used to Externally Insulate HVAC Ducts Standard Specification for Gypsum Board Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using an Electric Radiant Heat Energy Source

C1497 C1594 D56 D92 D93 D123 D149 D187 D202 D229 D240 D349 D350 D378 D460 D470 D495 D635 D876 D1000 D1047 D1230 D1310 D1322 D1405 D1711 D1826 D1830 D1929 D2219 D2220 Standard Specification for Cellulosic Fiber Stabilized Thermal Insulation Standard Specification for Polyimide Rigid Cellular Thermal Insulation Standard Test Method for Flash Point by Tag Closed Cup Tester Standard Test Method for Flash and Fire Points by Cleveland Open Cup Tester Standard Test Methods for Flash Point by Pensky-Martens Closed Cup Tester Standard Terminology Relating to Textiles Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies Standard Test Method for Burning Quality of Kerosine Standard Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter Standard Test Methods for Laminated Round Rods Used for Electrical Insulation Standard Test Methods for Flexible Treated Sleeving Used for Electrical Insulation Standard Test Methods for Rubber (Elastomeric) Conveyor Belting, Flat Type Standard Test Methods for Sampling and Chemical Analysis of Soaps and Soap Products Standard Test Methods for Crosslinked Insulations and Jackets for Wire and Cable Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications Standard Specification for Poly(Vinyl Chloride) Jacket for Wire and Cable Standard Test Method for Flammability of Apparel Textiles Standard Test Method for Flash Point and Fire Point of Liquids by Tag Open-Cup Apparatus Standard Test Method for Smoke Point of Kerosine and Aviation Turbine Fuel Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels Standard Terminology Relating to Electrical Insulation Standard Test Method for Calorific (Heating) Value of Gases in Natural Gas Range by Continuous Recording Calorimeter Standard Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method Standard Test Method for Determining Ignition Temperature of Plastics Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 60 C Operation Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 75 C Operation

D2304 D2584 D2633 D2671 D2766 D2843 D2859 D2863 D2898 D2903 D3014 D3032 D3065 D3115 D3143 D3144 D3149 D3150 D3201 D3251 D3278 D3284 D3338 D3426 D3466 D3523 D3574 D3638 D3675 Standard Test Method for Thermal Endurance of Rigid Electrical Insulating Materials Standard Test Method for Ignition Loss of Cured Reinforced Resins Standard Test Methods for Thermoplastic Insulations and Jackets for Wire and Cable Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use Standard Test Method for Specific Heat of Liquids and Solids Standard Test Method for Density of Smoke from the Burning or Decomposition of Plastics Standard Test Method for Ignition Characteristics of Finished Textile Floor Covering Materials Standard Test Method for Measuring the Minimum Oxygen Concentration to Support Candle-Like Combustion of Plastics (Oxygen Index) Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing Standard Specification for Crosslinked Chlorinated Polyolefin Heat-Shrinkable Tubing for Electrical Insulation Standard Practice for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing Standard Test Methods for Hookup Wire Insulation Standard Test Methods for Flammability of Aerosol Products Standard Test Method for Explosive Reactivity of Lubricants with Aerospace Alloys Under High Shear Standard Test Method for Flash Point of Cutback Asphalt with Tag Open-Cup Apparatus Standard Specification for Crosslinked Poly (Vinylidene Fluoride) Heat-Shrinkable Tubing for Electrical Insulation Standard Specification for Crosslinked Polyolefin Heat-Shrinkable Tubing for Electrical Insulation Standard Specification for Crosslinked and Noncrosslinked Poly(Vinyl Chloride) Heat-Shrinkable Tubing for Electrical Insulation Standard Test Method for Hygroscopic Properties of Fire-Retardant Wood and Wood-Based Products Standard Test Method for Thermal Endurance Characteristics of Electrical Insulating Varnishes Applied Over Film-Insulated Magnet Wire Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus Standard Practice for Combustible Gases in the Gas Space of Electrical Apparatus Using Portable Meters Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels Standard Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials Using Impulse Waves Standard Test Method for Ignition Temperature of Granular Activated Carbon Standard Test Method for Spontaneous Heating Values of Liquids and Solids (Differential Mackey Test) Standard Test Methods for Flexible Cellular Materials-Slab, Bonded, and Molded Urethane Foams Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source

D3679 D3801 D3806 D3828 D3874 D3934 D3941 D4000 D4151 D4206 D4391 D4529 D4804 D4809 D4850 D4851 D4868 D4976 D4982 D4986 D5025 D5048 D5132 D5207 D5238 D5288 D5306 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position Standard Test Method of Small-Scale Evaluation of Fire-Retardant Paints (2-Foot Tunnel Method) Standard Test Methods for Flash Point by Small Scale Closed Cup Tester Standard Test Method for Ignition of Materials by Hot Wire Sources Standard Test Method for Flash/No Flash Test-Equilibrium Method by a Closed-Cup Apparatus Standard Test Method for Flash Point by the Equilibrium Method with a Closed-Cup Apparatus Standard Classification System for Specifying Plastic Materials Standard Test Method for Flammability of Blankets Standard Test Method for Sustained Burning of Liquid Mixtures Using the Small Scale Open-Cup Apparatus Standard Terminology Relating to the Burning Behavior of Textiles Standard Test Method for Estimation of Net Heat of Combustion of Aviation Fuels Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics Standard Test Method for Heat of Combusion of Liquid Hydrocarbon Fuels by Bomb Calorimeter (Precision Method) Standard Terminology Relating to Fabrics and Fabric Test Methods Standard Test Methods for Coated and Laminated Fabrics for Architectural Use Standard Test Method for Estimation of Net and Gross Heat of Combustion of Hydrocarbon Burner and Diesel Fuels Standard Specification for Polyethylene Plastics Molding and Extrusion Materials Standard Test Methods for Flammability Potential Screening Analysis of Waste Standard Test Method for Horizontal Burning Characteristics of Cellular Polymeric Materials Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn- Through of Solid Plastics Using a 125-mm Flame Standard Test Method for Horizontal Burning Rate of Polymeric Materials Used in Occupant Compartments of Motor Vehicles Standard Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials Standard Test Method for Smoldering Combustion Potential of Cotton-Based Batting Standard Test Method for Determining Tracking Index of Electrical Insulating Materials Using Various Electrode Materials (Excluding Platinum) Standard Test Method for Linear Flame Propagation Rate of Lubricating Oils and Hydraulic Fluids

Standard Test Method for Smoke Obscuration of Insulating Materials Contained in Electrical or Optical D5424 Fiber Cables when Burning in a Vertical Cable Tray Configuration D5425 Standard Guide for Development of Fire Hazard Assessment Standards of Electrotechnical Products D5456 Standard Specification for Evaluation of Structural Composite Lumber Products Standard Test Method for Determining the Corrosive Effect of Combustion Products Using the Cone D5485 Corrosimeter Standard Test Method for Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood D5516 Exposed to Elevated Temperatures Standard Test Method for Heat Release, Flame Spread, Smoke Obscuration, and Mass Loss Testing of Insulating Materials Contained in Electrical or Optical Fiber Cables when Burning in a Vertical Cable Tray D5537 Configuration Standard Test Method for Evaluating the Effects of Fire-Retardant Treatments and Elevated Temperatures D5664 on Strength Properties of Fire-Retardant Treated Lumber D5865 Standard Test Method for Gross Calorific Value of Coal and Coke D6096 Standard Specification for Poly(Vinyl Chloride) Insulation for Wire and Cable, 90 C Operation Standard Test Method for Using a Cone Calorimeter to Determine Fire-Test Response Characteristics of D6113 Insulating Materials Contained in Electrical or Optical Fiber Cables D6194 Standard Test Method for Glow-Wire Ignition of Materials Standard Practice for Calculating Bending Strength Design Adjustment Factors for Fire-Retardant-Treated D6305 Plywood Roof Sheathing Standard Test Methods for Thin Thermally Conductive Solid Materials for Electrical Insulation and D6343 Dielectric Applications D6413 Standard Test Method for Flame Resistance of Textiles (Vertical Test) D6450 Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester Standard Practice for Calculating the Superimposed Load on Wood-Frame Walls for Standard Fire- D6513 Resistance Tests D6545 Standard Test Method for Flammability of Textiles Used in Children's Sleepwear D6630 Standard Guide for Low Slope Insulated Roof Membrane Assembly Performance D6662 Standard Specification for Polyolefin-Based Plastic Lumber Decking Boards D6668 Standard Test Method for Discrimination Between Flammability Ratings of F = 0 and F = 1 Standard Test Method for Measuring Maximum Spontaneous Heating Temperature of Art and Other D6801 Materials Standard Practice for Calculating Design Value Treatment Adjustment Factors for Fire-Retardant-Treated D6841 Lumber Standard Test Method to Evaluate Edge Binding Components Used in Mattresses After Exposure to an D7016 Open Flame

D7031 Standard Guide for Evaluating Mechanical and Physical Properties of Wood-Plastic Composite Products Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic D7032 Lumber Deck Boards, Stair Treads, Guards, and Handrails D7044 Standard Specification for Biodegradable Fire Resistant Hydraulic Fluids D7094 Standard Test Method for Flash Point by Modified Continuously Closed Cup (MCCCFP) Tester D7140 Standard Test Method to Measure Heat Transfer Through Textile Thermal Barrier Materials D7215 Standard Test Method for Calculated Flash Point from Simulated Distillation Analysis of Distillate Fuels D7236 Standard Test Method for Flash Point by Small Scale Closed Cup Tester (Ramp Method)1, 2 D7254 Standard Specification for Polypropylene (PP) Siding D7258 Standard Specification for Polymeric Piles Standard Practice for Sampling and Determination of Hydrogen Cyanide (HCN) in Combustion Effluents D7295 and Other Stationary Sources Standard Test Method for Determining Flammability Characteristics of Plastics and Other Solid Materials D7309 Using Microscale Combustion Calorimetry Standard Practice for Determination of the Heating Value of Gaseous Fuels using Calorimetry and Online/At-line D7314 Sampling Standard Practice for Evaluating Elevated Temperature Performance of Adhesives Used in End-Jointed D7374 Lumber D7425 Standard Specification for Spray Polyurethane Foam Used for Roofing Applications Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding with Foam Plastic Backing (Backed D7445 Vinyl Siding) D7470 Standard Practice for Evaluating Elevated Temperature Performance of End-Jointed Lumber Studs D7568 Standard Specification for Polyethylene-Based Structural-Grade Plastic Lumber for Outdoor Applications D7571 Standard Specification for Retained Sewn Seam Strength after Exposures to Hot Air and Open Flame D7793 Standard Specification for Insulated Vinyl Siding E69 Standard Test Method for Combustible Properties of Treated Wood by the Fire-Tube Apparatus E84 Standard Test Method for Surface Burning Characteristics of Building Materials E108 Standard Test Methods for Fire Tests of Roof Coverings E119 Standard Test Methods for Fire Tests of Building Construction and Materials E136 Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750⁰C E144 Standard Practice for Safe Use of Oxygen Combustion Vessels E162 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source E176 Standard Terminology of Fire Standards E205 Standard Specification for Glass and Oxygen Combustion Flask E285 Standard Test Method for Oxyacetylene Ablation Testing of Thermal Insulation Materials E459 Standard Test Method for Measuring Heat Transfer Rate Using a Thin-Skin Calorimeter

E502 E511 E535 E582 E598 E603 E605 E648 E659 E662 E681 E691 E698 E736 E759 E760 E761 E800 E814 E859 E906 E918 Standard Test Method for Selection and Use of ASTM Standards for the Determination of Flash Point of Chemicals by Closed Cup Methods Standard Test Method for Measuring Heat Flux using a Copper-Constantan Circular Foil, Heat-Flux Transducer Standard Practice for Preparation of Fire-Test-Response Standards Standard Test Method for Minimum Ignition Energy and Quenching Distance in Gaseous Mixtures Standard Test Method for Measuring Extreme Heat-Transfer Rates from High-Energy Environments Using a Transient, Null-Point Calorimeter Standard Guide for Room Fire Experiments Standard Test Methods for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using a Radiant Heat Energy Source Standard Test Method for Autoignition Temperature of Chemicals Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials Standard Test Method for Concentration Limits of Flammability of Chemicals (Vapors and Gases) Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method Standard Test Method for Kinetic Parameters for Thermally Unstable Materials Using Differential Scanning Calorimetry and the Flynn/Wall/Ozawa Method Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members Standard Test Method for Effect of Deflection on Sprayed Fire-Resistive Material Applied to Structural Members Standard Test Method for Effect of Impact on Bonding of Sprayed Fire-Resistive Material Applied to Structural Members Standard Test Method for Compressive Strength of Sprayed Fire-Resistive Material Applied to Structural Members Standard Guide for Measurement of Gases Present or Generated During Fires Standard Test Method for Fire Tests of Penetration Firestop Systems Standard Test Method for Air Erosion of Sprayed Fire-Resistive Materials (SFRMs) Applied to Structural Members Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using a Thermopile Method Standard Practice for Determining Limits of Flammability of Chemicals at Elevated Temperature and Pressure

E937 E970 E1226 E1232 E1317 E1321 E1352 E1353 E1354 E1355 E1386 E1388 E1412 E1413 E1445 E1461 E1474 E1491 E1513 E1515 E1529 E1537 E1546 E1590 E1591 E1618 Standard Test Method for Corrosion of Steel by Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members Standard Test Method for Critical Radiant Flux of Exposed Attic Floor Insulation Using a Radiant Heat Energy Source Standard Test Method for Explosibility of Dust Clouds Standard Test Method for Temperature Limit of Flammability of Chemicals Standard Test Method for Flammability of Marine Surface Finishes Standard Test Method for Determining Material Ignition and Flame Spread Properties Standard Test Method for Cigarette Ignition Resistance of Mock-Up Upholstered Furniture Assemblies Standard Test Methods for Cigarette Ignition Resistance of Components of Upholstered Furniture Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter Standard Guide for Evaluating the Predictive Capability of Deterministic Fire Models Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Solvent Extraction Standard Practice for Sampling of Headspace Vapors from Fire Debris Samples Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration with Activated Charcoal Standard Practice for Separation of Ignitable Liquid Residues from Fire Debris Samples by Dynamic Headspace Concentration Standard Terminology Relating to Hazard Potential of Chemicals Standard Test Method for Thermal Diffusivity by the Flash Method Standard Test Method for Determining the Heat Release Rate of Upholstered Furniture and Mattress Components or Composites Using a Bench Scale Oxygen Consumption Calorimeter Standard Test Method for Minimum Autoignition Temperature of Dust Clouds Standard Practice for Application of Sprayed Fire-Resistive Materials (SFRMs) Standard Test Method for Minimum Explosible Concentration of Combustible Dusts Standard Test Methods for Determining Effects of Large Hydrocarbon Pool Fires on Structural Members and Assemblies Standard Test Method for Fire Testing of Upholstered Furniture Standard Guide for Development of Fire-Hazard-Assessment Standards Standard Test Method for Fire Testing of Mattresses Standard Guide for Obtaining Data for Fire Growth Models Standard Test Method for Ignitable Liquid Residues in Extracts from Fire Debris Samples by Gas Chromatography-Mass Spectrometry

E1623 E1678 E1725 E1730 E1732 E1740 E1776 E1822 E1966 E1981 E1995 E2019 E2021 E2032 E2058 E2061 E2067 E2079 E2102 E2154 E2174 E2187 E2226 E2230 E2231 E2257 E2280 Standard Test Method for Determination of Fire and Thermal Parameters of Materials, Products, and Systems Using an Intermediate Scale Calorimeter (ICAL) Standard Test Method for Measuring Smoke Toxicity for Use in Fire Hazard Analysis Standard Test Methods for Fire Tests of Fire-Resistive Barrier Systems for Electrical System Components Standard Specification for Rigid Foam for Use in Structural Sandwich Panel Cores Standard Terminology Relating to Forensic Science Standard Test Method for Determining the Heat Release Rate and Other Fire-Test-Response Characteristics of Wall Covering or Ceiling Covering Composites Using a Cone Calorimeter Standard Guide for Development of Fire-Risk-Assessment Standards Standard Test Method for Fire Testing of Stacked Chairs Standard Test Method for Fire-Resistive Joint Systems Standard Guide for Assessing Thermal Stability of Materials by Methods of Accelerating Rate Calorimetry Standard Test Method for Measurement of Smoke Obscuration Using a Conical Radiant Source in a Single Closed Chamber, with the Test Specimen Oriented Horizontally Standard Test Method for Minimum Ignition Energy of a Dust Cloud in Air Standard Test Method for Hot-Surface Ignition Temperature of Dust Layers Standard Guide for Extension of Data from Fire Resistance Tests Conducted in Accordance with ASTM E119 Standard Test Methods for Measurement of Material Flammability Using a Fire Propagation Apparatus (FPA) Standard Guide for Fire Hazard Assessment of Rail Transportation Vehicles Standard Practice for Full-Scale Oxygen Consumption Calorimetry Fire Tests Standard Test Methods for Limiting Oxygen (Oxidant) Concentration in Gases and Vapors Standard Test Method for Measurement of Mass Loss and Ignitability for Screening Purposes Using a Conical Radiant Heater Standard Practice for Separation and Concentration of Ignitable Liquid Residues from Fire Debris Samples by Passive Headspace Concentration with Solid Phase Microextraction (SPME) Standard Practice for On-Site Inspection of Installed Firestops Standard Test Method for Measuring the Ignition Strength of Cigarettes Standard Practice for Application of Hose Stream Standard Practice for Thermal Qualification of Type B Packages for Radioactive Material Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics Standard Test Method for Room Fire Test of Wall and Ceiling Materials and Assemblies Standard Guide for Fire Hazard Assessment of the Effect of Upholstered Seating Furniture within Patient Rooms of Health Care Facilities

E2307 E2335 E2336 E2393 E2404 E2451 E2536 E2558 E2568 E2573 E2574 E2579 E2599 E2618 E2632 E2652 E2653 E2688 E2690 E2707 E2726 E2748 Standard Test Method for Determining Fire Resistance of Perimeter Fire Barriers Using Intermediate- Scale, Multi-story Test Apparatus Standard Guide for Laboratory Monitors Standard Test Methods for Fire Resistive Grease Duct Enclosure Systems Standard Practice for On-Site Inspection of Installed Fire Resistive Joint Systems and Perimeter Fire Barriers Standard Practice for Specimen Preparation and Mounting of Textile, Paper or Polymeric (including Vinyl) and Wood Wall or Ceiling Coverings, Facings and Veneers, to Assess Surface Burning Characteristics Standard Practice for Preserving Ignitable Liquids and Ignitable Liquid Residue Extracts from Fire Debris Samples Standard Guide for Assessment of Measurement Uncertainty in Fire Tests Standard Test Method for Determining Particulate Matter Emissions from Fires in Wood-Burning Fireplaces Standard Specification for PB Exterior Insulation and Finish Systems Standard Practice for Specimen Preparation and Mounting of Site-Fabricated Stretch Systems to Assess Surface Burning Characteristics Standard Test Method for Fire Testing of School Bus Seat Assemblies Standard Practice for Specimen Preparation and Mounting of Wood Products to Assess Surface Burning Characteristics Standard Practice for Specimen Preparation and Mounting of Reflective Insulation, Radiant Barrier and Vinyl Stretch Ceiling Materials for Building Applications to Assess Surface Burning Characteristics Standard Test Method for Measurement of Particulate Emissions and Heating Efficiency of Solid Fuel- Fired Hydronic Heating Applicances Standard Test Method for Evaluating the Under-Deck Fire Test Response of Deck Materials Standard Test Method for Behavior of Materials in a Tube Furnace with a Cone-shaped Airflow Stabilizer, at 750⁰C Standard Practice for Conducting an Interlaboratory Study to Determine Precision Estimates for a Fire Test Method with Fewer Than Six Participating Laboratories Standard Practice for Specimen Preparation and Mounting of Tapes to Assess Surface Burning Characteristics Standard Practice for Specimen Preparation and Mounting of Caulks and Sealants to Assess Surface Burning Characteristics Standard Test Method for Determining Fire Penetration of Exterior Wall Assemblies Using a Direct Flame Impingement Exposure Standard Test Method for Evaluating the Fire-Test-Response of Deck Structures to Burning Brands Standard Guide for Fire-Resistance Experiments

E2749 E2750 E2768 E2816 E2837 E2881 E2886 E2902 E2912 E2957 E2965 E2988 E2989 E3020 E3021 E3048 F400 F495 F793 F955 F963 F1002 F1060 F1085 Standard Practice for Measuring the Uniformity of Furnace Exposure on Test Specimens Standard Guide for Extension of Data from Penetration Firestop System Tests Conducted in Accordance with ASTM E814 Standard Test Method for Extended Duration Surface Burning Characteristics of Building Materials (30 min Tunnel Test) Standard Test Methods for Fire Resistive Metallic HVAC Duct Systems Standard Test Method for Determining the Fire Resistance of Continuity Head-of-Wall Joint Systems Installed Between Rated Wall Assemblies and Nonrated Horizontal Assemblies Standard Test Method for Extraction and Derivatization of Vegetable Oils and Fats from Fire Debris and Liquid Samples with Analysis by Gas Chromatography-Mass Spectrometry Standard Test Method for Evaluating the Ability of Exterior Vents to Resist the Entry of Embers and Direct Flame Impingement Standard Practice for Measurement of Body Armor Wearers Standard Test Method for Fire Test of Non-Mechanical Fire Dampers Used in Vented Construction Standard Test Method for Resistance to Wildfire Penetration of Eaves, Soffits and Other Projections Standard Test Method for Determination of Low Levels of Heat Release Rate for Materials and Products Using an Oxygen Consumption Calorimeter Standard Practice for Specimen Preparation and Mounting of Flexible Fibrous Glass Insulation for Metal Buildings to Assess Surface Burning Characteristics Standard Guide for Assessment of Continued Applicability of Fire Test Reports Used in Building Regulation Standard Practice for Ignition Sources Standard Guide for Evaluating the Relative Effectiveness of Building Systems to Resist the Passage of Products of Combustion Based on the Aggregation of Leakage Rates Standard Test Method for Determination of Time to Burn-Through Using the Intermediate Scale Calorimeter (ICAL) Radiant Panel Standard Consumer Safety Specification for Lighters Standard Test Method for Weight Loss of Gasket Materials Upon Exposure to Elevated Temperatures Standard Classification of Wall Coverings by Use Characteristics Standard Test Method for Evaluating Heat Transfer through Materials for Protective Clothing Upon Contact with Molten Substances Standard Consumer Safety Specification for Toy Safety Standard Performance Specification for Protective Clothing and Materials for Use by Workers Exposed to Specific Molten Substances and Related Thermal Hazards Standard Test Method for Evaluation of Conductive and Compressive Heat Resistance (CCHR) Standard Specification for Mattress and Box Springs for Use in Berths in Marine Vessels

F1092 F1141 F1173 F1198 F1291 F1358 F1387 F1449 F1494 F1506 F1534 F1550 F1731 F1868 F1870 F1891 F1915 F1918 F1930 F1939 F1955 F1958 F1959 Standard Specification for Fiberglass (GRP) Pultruded Open-Weather Storm and Guard, Square Railing Systems Standard Specification for Wall Coverings Standard Specification for Thermosetting Resin Fiberglass Pipe Systems to be Used for Marine Applications Standard Guide for Shipboard Fire Detection Systems Standard Test Method for Measuring the Thermal Insulation of Clothing Using a Heated Manikin Standard Test Method for Effects of Flame Impingement on Materials Used in Protective Clothing Not Designated Primarily for Flame Resistance Standard Specification for Performance of Piping and Tubing Mechanically Attached Fittings Standard Guide for Industrial Laundering of Flame, Thermal, and Arc Resistant Clothing Standard Terminology Relating to Protective Clothing Standard Performance Specification for Flame Resistant and Arc Rated Textile Materials for Wearing Apparel for Use by Electrical Workers Exposed to Momentary Electric Arc and Related Thermal Hazards Standard Test Method for Determining Changes in Fire-Test-Response Characteristics of Cushioning Materials After Water Leaching Standard Test Method for Determination of Fire-Test-Response Characteristics of Components or Composites of Mattresses or Furniture for Use in Correctional Facilities after Exposure to Vandalism, by Employing a Bench Scale Oxygen Consumption Calorimeter Standard Practice for Body Measurements and Sizing of Fire and Rescue Services Uniforms and Other Thermal Hazard Protective Clothing Standard Test Method for Thermal and Evaporative Resistance of Clothing Materials Using a Sweating Hot Plate Standard Guide for Selection of Fire Test Methods for the Assessment of Upholstered Furnishings in Detention and Correctional Facilities Standard Specification for Arc and Flame Resistant Rainwear Standard Test Methods for Glazing for Detention Facilities Standard Safety Performance Specification for Soft Contained Play Equipment Standard Test Method for Evaluation of Flame Resistant Clothing for Protection Against Fire Simulations Using an Instrumented Manikin Standard Test Method for Radiant Heat Resistance of Flame Resistant Clothing Materials with Continuous Heating Standard Test Method for Flammability of Sleeping Bags Standard Test Method for Determining the Ignitability of Non-flame-Resistant Materials for Clothing by Electric Arc Exposure Method Using Mannequins Standard Test Method for Determining the Arc Rating of Materials for Clothing

F1972 F1989 F2058 F2178 F2201 F2326 F2370 F2417 F2601 F2676 F2697 F2700 F2702 F2703 F2731 F2733 F2757 F2866 F2877 F2894 F3059 G72 G74 Standard Guide for Terminology Relating to Candles and Associated Accessory Items Standard Specification for Cooking Fire Suppression Blankets Standard Specification for Candle Fire Safety Labeling Standard Test Method for Determining the Arc Rating and Standard Specification for Eye or Face Protective Products Standard Consumer Safety Specification for Utility Lighters Standard Test Method for Collection and Analysis of Visible Emissions from Candles as They Burn Standard Test Method for Measuring the Evaporative Resistance of Clothing Using a Sweating Manikin Standard Specification for Fire Safety for Candles Standard Specification for Fire Safety for Candle Accessories Standard Test Method for Determining the Protective Performance of an Arc Protective Blanket for Electric Arc Hazards Standard Test Methods for Physical Assault on Overhead Horizontal Fixed Barriers for Detention and Correctional Facilities Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing with Continuous Heating Standard Test Method for Radiant Heat Performance of Flame Resistant Clothing Materials with Burn Injury Prediction Standard Test Method for Unsteady-State Heat Transfer Evaluation of Flame Resistant Materials for Clothing with Burn Injury Prediction Standard Test Method for Measuring the Transmitted and Stored Energy of Firefighter Protective Clothing Systems Standard Specification for Flame Resistant Rainwear for Protection Against Flame Hazards Standard Guide for Home Laundering Care and Maintenance of Flame, Thermal and Arc Resistant Clothing Standard Test Method for Flammability of a Membrane Switch in Defined Assembly Standard Test Method for Shock Testing of Structural Insulation of A-Class Divisions Constructed of Steel or Aluminum Standard Test Method for Evaluation of Materials, Protective Clothing and Equipment for Heat Resistance Using a Hot Air Circulating Oven Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding Standard Test Method for Autogenous Ignition Temperature of Liquids and Solids in a High-Pressure Oxygen-Enriched Environment Standard Test Method for Ignition Sensitivity of Nonmetallic Materials and Components by Gaseous Fluid Impact

G86 G114 G124 G125 G145 G175 Standard Test Method for Determining Ignition Sensitivity of Materials to Mechanical Impact in Ambient Liquid Oxygen and Pressurized Liquid and Gaseous Oxygen Environments Standard Practices for Evaluating the Age Resistance of Polymeric Materials Used in Oxygen Service Standard Test Method for Determining the Combustion Behavior of Metallic Materials in Oxygen-Enriched Atmospheres Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants Standard Guide for Studying Fire Incidents in Oxygen Systems Standard Test Method for Evaluating the Ignition Sensitivity and Fault Tolerance of Oxygen Pressure Regulators Used for Medical and Emergency Applications