Canolux LED Petrol Station Forecourt Luminaires
Point source LEDs provide excellent opportunities to direct light accurately improving uniformity and reducing the electrical load. Well designed and manufactured optical components can provide the desired light distribution and lit appearance whilst limiting glare and providing optimum energy efficiency. Canolux LED technology can be combined with Smart External intelligent controls to provide a low maintenance, low energy fit and forget solution for lighting garage forecourts. 2
Contents Canolux LED Range 4 Full Specification 6 Smart External 8 Motionline Scenarios 10 Smart Booster 12 Motionline Linking 13 Programmability Scenarios 14 Programmable Features 16 Dimensions 17 10 Year Life Costing Analysis 18 HID vs LED Comparison 19 3
Recessed 54 high power white LEDs as standard Special versions available on request Fully electronic LED drivers Acrylic front cover Recessed or surface mounting options Can replace existing Canolux HIT luminaires Photometric Guide Canolux LED 110W LED TRANSVERSE 120 240 360 AXIAL Optional fully integral Smart External Micro-pod Sensor for automatic switching, dimming, presence detection and daylight sensing (see page 8 for details) 480 CANDELAS PER 1000 LUMENS 4
Surface IP43 For dimensions and fixings (see page 17) for details. Range APPROX. DESCRIPTION CAT. No. kg Recessed Standard CX 14641 14.3 Smart External CX 14642 14.4 Surface Mounted Standard CX 14643 10.0 Smart External CX 14644 10.1 5
Specification Heat Sink Body Zinc coated steel body with white full polyester powder finish, black anodised aluminium rear heat sink for LED cooling. Cover 2.8mm thick acrylic with reeded prisms for increased downward intensity. LED Driver High quality electronic drivers, mounted in dedicated cool gear compartments. 6
Standards Complies with BS EN 60598 2-1, Classified IP43, CE Marked. Voltage 220-240V, 50-60Hz, other voltages on request. LEDs High quality, high flux, >60,000hr rated life, 4000k, 65+ Ra LEDs mounted on a replaceable LED board with plug and socket connections. Other colour options available. Smart System Electronic dimmable LED drivers are automatically controlled by the dedicated Smart External Micro-pod Sensor allowing instant switching and dimming of individual and / or groups of luminaires (see page 8 for details). 7
Presence Detection Traditionally, spaces such as petrol station forecourts remain lit all night (and often all day) even when occupancy is low. The Smart External Micro-pod Sensor built into each Canolux LED luminaire allows the luminaires to be switched off or dimmed down to a low output level when the area is unoccupied. As soon as the sensor detects movement, the luminaire will return back to full output. Presence detection parameters can be adjusted using a hand-held infra-red Smart External Programmer (see pages 14-15). Canolux LED Smart External The world s ever increasing demand for energy is rapidly changing our environment and the need for energy efficiency in every aspect of our daily lives has never been greater. Smart External is the latest addition to the Thorlux range of control systems bringing intelligent lighting control to a new range of exterior LED based luminaires. Combining programmable presence detection and light sensing with seven day programmable switching schedules massive, energy savings and extended maintenance cycles are possible. Truly fit and forget lighting. 8
Ambient Light Control The Smart External Micro-pod Sensor incorporates an ambient light sensor which will enable at dusk and disable at dawn. Ambient light level switching can be adjusted using a hand-held infra-red Smart External Programmer (see pages 14-15). SAVE ENERGY SAVE MONEY SAVE THE ENVIRONMENT 9
Motionline Scenarios (Platforms 2 & 3) Master Motionline Motionline 1 Motionline 2 The Smart External system can operate at three different levels (platforms) offering increasing functionality. PLATFORM 1 : STAND-ALONE The simplest level. Each luminaire operates as a stand-alone item. PLATFORM 2 : MOTIONLINE LINKED Groups of luminaires are linked with a two-core bus, called the Motionline, allowing each luminaire to pass presence detection to all luminaires within the group (see diagram above). PLATFORM 3 : TIME AND WEB BASED CONTROL Offers time schedule control, so that luminaires may be switched off when not needed (can be remotely configured through a secure web-site). It also allows local configuration and manual override (Smart External Controller required). 10
APPROX. DESCRIPTION CAT. No. kg Smart External Controller SC 14478 1.4 11
Smart Booster The addition of a Smart External Booster allows other lighting such as signage and LED feature lighting to be switched from the canopy Smart luminaire s PIR detector (PLATFORM 2 & 3) and via time control (PLATFORM 3). The Smart External Booster also allows up to 4 motionline groups to communicate with each other (see diagram on page 13). APPROX. DESCRIPTION CAT. No. kg Smart External Booster SC 14430 0.9 For dimensions and fixings (see page 17) for details. 12
Motionline Linking Max. 50 ballasts, 500 metres Max. 50 ballasts, 500 metres SEC M1 Max. 50 ballasts, 500 metres MM RS SEB M2 SEC Smart External Controller (optional) Max. 5A DS SEB Smart External Booster MM Master Motionline Open CENTRAL MOTION M1 Motionline 1 M2 Motionline 2 Max. 64 ballasts, 300 metres DS Digitally Switched (DSI) RS Relay Switched Open Canolux LED Bulkhead/ LED Feature Signage Luminaires 13
Programmability Scenarios Zone 1 Zone 2 Zone 3 Zone 4 Luminaires can be individually programmed (see page 16) to dim or switch in areas of low occupancy or in daylight conditions (Smart External Programmer required). The system allows re-programming at any time should the lighting emphasis need changing. Forecourts can be set as required with an emphasis on the following scenarios (see diagram above): A : BEST APPEARANCE Realising energy savings whilst keeping an open for business feel. B : MAXIMUM ENERGY SAVINGS for the lowest running costs. 14
Lighting Zone A - BEST APPEARANCE B - MAXIMUM ENERGY SAVING ZONE 1 MAIN ENTRANCE AND EXIT On at 30% output. Switched off when daylight, on all night at 30% output. ZONE 2 SHOP ENTRANCE AND EXIT Switched off when sufficient daylight, on all night at full output. Switched off when sufficient daylight, dims down to 30% 5 minutes after last detected movement. ZONE 3 MAIN RE-FUELING AREA Switched off when sufficient daylight, at night dims to 30% 5 minutes after last detected movement. Stays at 30% until dawn, or next detected movement. Switched off when sufficient daylight, dims down to 30% after 5 minutes, then switches off 10 minutes later if no further movement is detected. ZONE 4 AIR/WATER PUMPS Switched off when sufficient daylight, at night dims to 30% 5 minutes after last detected movement. Stays at 30% until dawn, or next detected movement. Switched off when sufficient daylight, dims down to 30% after 5 minutes, then switches off 10 minutes later if no further movement is detected. These are only a few examples, the possibilities are numerous. 15
Programmable Features One of the key benefits of the Smart External system is the ability to program every luminaire differently. Each luminaire can be tailored to suit its own very specific local requirements. The main programmable features are: Lights on setting - Completely variable. Factory setting approximately 200lux. Security level (see also Security delay) - Can be set anywhere between minimum and maximum. Factory setting 30%. PIR sensitivity - May be adjusted to suit conditions. No presence delay - After a variable delay (30 seconds to 10 hours) the luminaires turn off or go to the Security Level. Factory setting - 5 minutes 30% continuous security level. Min lamp - The minimum dim level of the lamps can beset. Factory setting 10%. Max lamp - The maximum lamp level can be set to tune the levels to local conditions. Factory setting 100%. Security delay - This allows an interim delay (30 seconds to 10 hours, or continuous) at Security level. For example, all luminaires around the forecourt may be set to switch off except for entrance/exit areas which will reduce to 50%, for a further 3 hours (assuming no presence detected) or whilst the forecourt is open. Alternatively as a security feature, perhaps 1 in 5 lights may be kept on continuously at any chosen level and only increase to full brilliance when a person or car enters the forecourt or space. APPROX. DESCRIPTION CAT. No. kg Smart External Programmer SC 14228 0.4 16
Dimensions 557 28-6.5 dia. holes 8 91 98 610 49 580 216 343 302 148 593 91 552 Recessed Surface 2-40 x 10mm slots 182 62 120 CRS. 4 x 5mm dia. fixing holes under cover 180 165 CRS. 120 CRS. Smart Booster 167 CRS. 4 x 5 x 9mm knock-out slots Thorlux Lighting is a corporate member of the APEA (Association for Petroleum and Explosives Administration) which offers guidance in the design and build of Petrol Station Forecourts. 17
10 Year Life Costing Analysis CAPITAL, WATTAGE ENERGY ENERGY ENERGY AND PER COST PER COST MAINTENANCE DESCRIPTION QUANTITY LUMINAIRE ANNUM (10 YEARS) COST (10 YEARS) Typical 250W MBI-T vs LED Typical 250W MBI-T 16 275 4,625 55,532 77,562 Canolux 110W LED 16 130 2,186 26,251 40,595 SAVING - 145 2,439 29,221 36,970 Typical 250W MBI-T vs LED Smart External Typical 250W MBI-T 16 275 4,625 55,532 77,562 Canolux 110W LED Smart External 16 130 1,071 12,863 22,567 SAVING - 145 3,554 42,669 54,995 Design / Installation / Maintenance assumptions: 1. Canopy size is 15m x 15m. 2. 16 Luminaires are mounted at a height of 5m. 3. Comparison between 250W metal halide Canolux and 110W Canolux LED, conventionally switched and Smart External versions. 4. 24 Hour opening of forecourt (luminaires permanently on). 5. Average 30% energy saving due to dimming and 30% energy saving due to presence detection. 6. Electricity price 12p/kWh (10 year cost includes 4% annual increase year on year). 7. Site distance is 50 miles from the service depot (for maintenance calculations). 8. Maintenance team comprises 2 people, 1 vehicle and access equipment. 18
HID vs LED Comparison Canolux LED can be installed as a direct replacement for 250W metal halide luminaires and will achieve acceptable illuminance at the pump. FACTOR TYPICAL 250W METAL HALIDE CANOLUX CANOLUX LED Maintenance factor * 0.70 0.80 Average illuminance at floor 400 lux 330 lux Average vertical illuminance at pump 140 lux 120 lux Max GR (Glare) 20 19 Maximum total energy load 4.56 kw 2.08 kw * The maintenance factor for the 250W metal halide is lower due to poorer lumen maintenance of the lamp. Energy consumed (W) 120 80 40 Energy Consumption Analysis The Canolux displays an almost linear response to energy saved and light produced during dimming. For Example, if lamps are running at 30% light output then 68% power saving is achieved. 0 100% 80% 60% 40% 20% 0% (Off) Dim Level (%) 19
Designers, manufacturers and suppliers of professional lighting systems INDUSTRIAL LUMINAIRES COMMERCIAL LUMINAIRES FLOODLIGHTING LUMINAIRES ARCHITECTURAL LUMINAIRES CONTROLS AND SYSTEMS TUNNEL LIGHTING SYSTEMS Merse Road North Moons Moat Redditch Worcestershire B98 9HH England Tel: + 44 (0)1527 583200 Fax: + 44 (0)1527 584177 e-mail: thorlux@thorlux.co.uk Web: www.thorlux.com Direct UK Sales Line: 01527 583222 Thorlux Carbon Offsetting Project: www.thorlux.com/trees A DIVISION OF F.W. THORPE PLC The information given in this catalogue is typical and must not be interpreted as a guarantee of individual product performance and/or characteristics. We reserve the right to alter specifications and designs without prior notice. THORLUX is a Registered Trade Mark of F.W. Thorpe Plc. CANOLUX and SMART EXTERNAL are Trade Marks of F.W. Thorpe Plc. P.N. 2351A Oct. 11 TM TM ISO 9001 FM 10913 ISO 14001 EMS 532104