smardy - pure water Reverse osmosis system YR100-A 75 GPD Instruction manual [EN] Please read this manual carefully before operating the device and subsequently keep the instruction manual safely and within close proximity to the device! Note: we reserve the right to make technological and functional changes or surface modifications to improve the functions and performances of our products. -Cover sheet-
Summary General Page 1 Contents Page 2 Scope of supply Page 2 Device identification Page 2 Safety instructions Page 3 Product launch Page 4 Product specifications Page 5 Filter description Page 5 Installation Page 6 Instruction manual Page 7-9 Care and maintenance Page 10-11 Error messages and repair Page 12 Maintenance table Page 13 Warranty conditions Page 14 Replacement filters Page 16 Scope of supply Box Accessories box Accessories bag Main device (1 piece) Water connection box (1 set) Power cable (220-240V 10A) Water tank (1 piece) Tank cap (1 piece) Instruction manual Device identification Symbol YR100-A Significance Model number in accordance with type label. The device meets all the legal requirements of the European standards. The device is suitable for the contact with foodstuffs. Labelled product must not be disposed of with household waste. -2-
Safety instructions Do not make any modifications to the installation and do not disassemble the device. Improper disassembly or modification can lead to malfunctions or leakages. Do not leave any items on top of the device risk of overheating! Do not put any heavy items on top of the device, this can damage inner components and lead to malfunctions. Do not let the device come into contact with corroding items, this could affect the housing and toxic or dangerous substances could penetrate. Water pressure Water source: Drinking water Pressure: < 3 bar Do not expose the device to high water pressure, this could damage the water supply lines. A recommended water inlet pressure ranges between 0,5 and 3,5 bar. Power supply The power cable and the power plug are only suitable for this product, tested and approved. ATTENTION- Use the provided power supply cable and do not operate the device with other commercial connection cables. Do not connect or unplug the power plug with wet hands! Troubleshooting for errors Remove the power and water supply immediately, when the product is defective or presents a malfuntion. In such cases, please contact our support team at info@smardy.de Scope of application and temperature range 4 C - 38 C in a dry and clean area. Please protect the device against dirt, dust, external moisture and against heat. In addition, avoid direct sunlight the water filter may not be installed in the vicinity of direct sunlight. The feed water should not exceed a temperature of 38 C, this could damage the reverse osmosis membrane and lead to malfunction. Do not put the device into operation in an ambient temperature below 5 C and ensure that the water in the device can not freeze, to prevent broken supply lines and water loss. Do not use the device outdoors to prevent a premature aging of the water pipes and possible malfunction. Do not leave the device near fire sources. Excessive temperatures can deform the housing and lead to malfunction and leakage of the device. Transport of the water filtration system Make sure to drain the water in the water tank before you tilt your device up to 45 degrees. Maintenance Do not open the device yourself to repair it. Unauthorized opening of the system invalidates the warranty. Accessories and filters Only use original accessories which are tested and approved by us. Set up and install out of the reach of children Please ensure that children do not use or operate the device unsupervised. -3-
Product launch Product description The smardy pure water system is a combination of reverse osmosis and hydrogen enriching water system. It offers water in four temperature ranges to choose from: normal filtered drinking water, boiled water, hot water and warm water in order to meet the all the needs and requirements of the family. For this purpose, normal tap water will be filled into the provided tank and will be purified from harmful substances like nitrate, lime, medication, viruses, bacteria, heavy metals, microplastic, pesticides, chlorine, etc. via the membrane, sediment and activated carbon filters. -4-
Product specifications Permissible humidity: <85% Rated output: 2150W Nominal pressure: 0 Bar Permissible humidity: 4-38 C Rated output: 2100W Nominal pressure: 3 bar max. water equivalent inlet < 1000 PPM Nominal voltage: 220-240V / 50Hz Output: 0,26 L / Min Only use tap water Max. 285 liter per day Dimensions (L*W*H in mm) 380*244*390 Filter description Description Function Filter change Filter 1 - prefilter 5micron PP filter + Activated carbon filter Eliminates sediments, rust, asbestos, sand, sludge, humic substances and other large residues. 6-12 Months Filter 2 - Activated carbon filter + 1micron PP filter Reverse osmosis filter - RO Membrane - 0,0001 micron filter system Consisting of a high-quality activated carbon block filter + 1micron PP filter. Safely retains chlorine, chemicals and other harmful organic compounds and protects the RO membrane. Removes impurities larger than 0,0001 μm, like e.g heavy metals, uranium, hormones, harmful chemicals, bacteria, viruses, pesticides, medication, as well as organic and inorganic compounds. 6-12 Months 12-24 Months Note: Membrane and filter change intervals depend on the quality of the incoming water, pressure and temperature and can therefore vary. -5-
Installation Method 1: off-grid installation no structural changes required. Attention: 1. Do not remove both caps/ plugs on the back side of the device, if the device was not installed as per m per installation type method 2. And thus prevent the water from leaking. 2. Do not remove the water tank when the device produces water (indicator on the control panel). This way you prevent malfunction and damage to the water filters. 3. Empty the wastewater regularly and do not refill water into the inserted tank from above. Method 2: grid-connected installation possible structural changes required. Attention: 1. For the grid-connected installation of the water filters, please contact our support team to obtain more detailed information about the assembly and special features. We will be pleased to advise you with all the questions relating to the device. -6-
Instruction manual 1. Description of the control panel Note: The control panel is a fully functional touch display, which indicates the actual use of the device. Symbol Display Explanation of the functions Display digit OUT Digital TDS-water measuring device(tds = total dissolved solids = total quantity of dissolved solids). Measures and indicates the content of organic and inorganic substances of the filtered water. Display digit IN Symbol lights up Filter change Lights up Symbol lights up Digital TDS-water measuring device (TDS = total dissolved solids = total quantity of dissolved solids). Measures and indicates the content of organic and inorganic substances of the unfiltered water. The symbol lights up if there is not enough tap water available in the water tank, or when the TDS-value of the unfiltered water is too high. (reference this, also see the note on page 8) The symbols flash by expiry of the filter life and inform you of replacing the filters accordingly. Please only use compatible replacement filters. Child safety activated, to prevent improper use and injuries from burns. Symbol lights up Symbol lights up Symbol lights up Symbol lights up MODE key Standard function of the device by pressing the water key, filtered drinking water flows from the outlet. Select hot water by touching the MODE key. Select warm water e.g for tea by touching the MODE key. Select warm water e.g for baby food by touching the MODE key. Use this key to select the various water temperatures. Blue Permanent light Blue light flashes Press this key to fill with the selected water. With a blue permanent light there is still sufficient filtered water available in the tank. There is no longer sufficient water available in the system. Please wait 3 minutes and subsequently press the key once again to fill up with filtered water. -7-
2. Important note for the initial commissioning: Before you ingest the water, it is necessary to flush out the new filters and the internal tank. Therefore let at least 3 full watertanks flow through the device. 3. How do you get filtered water? Place an empty glass under the outlet. Note: For this purpose use the provided holder for support and to protect the table from splashing water. Press the "MODE" key to select filtered water in the desired temperature. Press the water key to start with the water outlet (blue light lights up). Press the water key once again to stop the water outlet (blue light goes out). -8-
Information for general usage: 1. Auto-stop function: The unit is equipped with an automatic stop function. This interrupts the waterflow with normal filtered water and warm water after 0,5 liters and with hot water after 60 seconds. 2. Child safety lock: The device is equipped with a child safety lock. This function is activated by default, as soon as the device is connected to the power supply. With the activated child safety lock, normal filtered water will flow out of the device upon request. You can still select hot water tea/coffee water or warm water by pressing the MODE key. However, if within 10 seconds no request of the selected water occurs, the function will automatically return to the normal water mode. To deactivate the child safety lock, press and hold the water key To reactivate the child safety lock, press and hold the water key for 5 seconds. once again for 5 seconds. 3. Emptying of the internal water tank In order to be able to transport or repair the device, it is necessary to empty the internal tank. To do this, press and hold the MODE key and the water outlet key simultaneously for 3 seconds. As soon as the total water (approx. 1 liter) has flown out of the device, please press the water outlet key once. The internal tank is now empty and the device can be transported/repaired. 4. Flashing icon When the symbol lights up, there is not sufficient tap water in the external tank of the device or the TDSvalue of the unfiltered water in the external tank exceeds the limit value. Therefore empty the external tank periodically and refill with fresh tap water. When the blue symbol flashes, there is not sufficient water in the internal tank. No more water flows out. -9-
Care and maintenance 1. Filter change The device informs and reminds you independently of necessary filter changes via this indicator on the display. The symbols flash when the service life of the filters has been reached and inform you of changing the filters accordingly. 2. Procedure work steps Our device is equipped with so-called QuickChange filters. Please only use compatible replacement filters. You can obtain these quickly and reliably in our online shop. (s. page 15) 3. Reset filter indicator - Reset After the filter change it is necessary to reset the filter indicator with the aid of the reset buttons (see picture). Press and hold button 1 2 for 5 seconds, to reset filter 1 and 2, press and hold button 3 for 5 seconds, to reset filter 3. -10-
4. Descaling of the external water tank Depending on the degree of water hardness in your regio, over time there will be calcifications in the bottom and on the inner walls of the external water tank. The harder the water, the faster the formation of calcifications. It is important to descale the external water tank of the smardy - pure water reverse osmosis system at least every 3 months but not more often than six times a year. Descaling process 1. Remove the water tank from the device. 2. In a measuring cup mix 50 grams of smardy special decalcifier with 1 liter warm water (approx. 50 degrees). Stir the liquid, until the powder is completely dissolved. 3. Fill the water container with the descaling mixture up to the mark MAX. 4. Leave the mixture in the tank for approx. 1 hour. 5. Empty the water tank and rinse out several times with clear water. 6. Reinsert the cleaned water tank into the device. Note: You can also use other suitable descaling agents, in doing so, please follow the manufacturer s instructions. smardy special decalcifier is available via the following link: 5. Disinfection of the device https://www.amazon.co.uk/dp/b06zzqwm37 We recommend to disinfect the smardy - pure water reverse osmosis system regularly, at the latest every 6-12 months (when changing the filters). For this purpose you obtain a specially designed disinfection set in our accessories shop. For further detailed instructions, please refer to the application instructions included in the disinfection set. This set is available via the following link: https://www.amazon.co.uk/dp/b06y653p7r -11-
Error messages and repairs ATTENTION! If a malfunction occurs during the operation of your device: Water escapes from the tubes or other components Some elements do not function correctly Device components conduct electricity You detect other anomalies or errors on the device and/ or an error code appears on the display, please switch off the device, remove the power plug and contact our customer service at info@smardy.de Error code on the display without without without Malfunction No normal tempered water is being dispensed Low water pressure or no water supply Button/ display does not function The device is damaged or defect. Action Check whether the power plug is loose or not plugged in. There is not sufficient water in the tap water tank, the symbol flashes. Check the inlet water pressure There is not sufficient water in the tap water tank Check whether the power plug is loose or not plugged in. Contact our customer service E1 Water pump defective Contact our customer service E2 Water level defective Contact our customer service E3 Temperature sensor defective Contact our customer service E4 Outlet valve defective Contact our customer service E5 Valve cleaning defective Contact our customer service E6 Outlet pump defective Contact our customer service E8 Reset button defective Contact our customer service For all other defects or malfunctions of the device, please unplug the power plug immediately and inform our customer service. When you do not use the device for a long period of time, also disconnect the device from the water supply or unplug the power cable. In the event of damage to the device/or is components please contact our customer service department or a specialist. We shall not be liable for possible damages caused by improper handling. Return shipment If the problem cannot be solved by our customer service department, please return the device to us. Do not return it freight forward but as a franked package. Also avoid external damages and contamination of the device. If possible, return the device to us in its original packaging with all accessories and all packaging components. If you no longer have the original packaging, please ensure an appropriate packaging to avoid damage during transport. -12-
Maintenance table Brought into operation for the first time on: Month Year FILTER: 1 FILTER 2 FILTER 3 Composite Micro Filter Replaced on: Composite Activated Carbon Replaced on: RO Membrane Replaced on: -13-
Warranty conditions JustMore GmbH & Co. KG gives a 24 month guarantee from the date of purchase on all material and processing errors of the device (except for all filters, membranes and storage tanks). The original purchase receipt serves as the warranty certificate. During this period, we will repair the product by installing new components free of charge. In the event that problems occur during or after the expiry of the guarantee period, please contact our customer service department at info@smardy.de. This warranty applies only to the original purchaser. It only covers material and processing errors which occur by proper use. The warranty does not apply to damages caused by transport, improper handling, negligence, as well as interventions and changes undertaken by unauthorized agencies. JustMore GmbH & Co. KG is not liable for consequential damages that arise from the use of the device. All rights reserved JustMore GmbH & Co. KG Robert-Bosch-Straße 6 B 86830 Schwabmünchen - Germany - Technical changes reserved -14-
Notes -15-
https://www.amazon.co.uk/dp/b01n40w222 https://www.amazon.co.uk/dp/b01mymr309 https://www.amazon.co.uk/dp/b01n750ukf Replacement filters 6-12 Months* 6-12 Months* 12-24 Months* *recommended change interval -Back cover-