ONTMPORRY KITHN N PRP UT INSTLLTION INSTRUTIONS Kitchen Model #s: 3600-12 3600-18 3800 3825 Prep Model #s: 3500 3900 3925 3600-12 3600-18 3800 3825 3500 3900 3925
OR YOU IN YOUR INSTLLTION: 1 2 3 4 Turn off water supply. Observe all local plumbing codes. Inspect plumbing for signs of damage. Replace as necessary. O NOT use petroleum based products on this faucet. RQUIR TOOLS: djustable Wrench Phillips Screwdriver hannel Locks HNL POSITION Waterstone faucets are designed to be installed in 3 different faucet positions. hoose to have the handle on left, front or right. Your faucet is factory configured for the most common positions - a front and right side installation. To reverse this and have the handle positioned on the left, connect the hose for cold water to the hot supply and the hose for hot water to the cold supply. This will maintain the relationship of pulling the handle for hot water or pushing for cold water. UT INSTLLTION HNL ON LT HNL IN RONT HNL ON RIHT OUNTR Remove clamp nut () and washer () from threaded shroud (). it flexible hoses () and rigid sidespray tube () through hole on counter or sink. (No plumbers putty is required. O-ring seals base). Slide washer and thread the clamp nut onto threaded shroud. Tighten nut snug to underside of sink or counter. Turn faucet to the desired handle position. Securely tighten clamp screws ().
HOW TO JUST HNL POSITION N HNL TNSION I.1 ORIINL TORY POSITION MY HIT KSPLSH NW JUST POSITION LRS KSPLSH Unscrew and remove metal cap () and Hot and old Indicator Ring (). Unscrew and remove holding screw () and washer (). Hold handle () in a vertical position. Wiggle and pull straight off faucet. Rotate handle 22 degrees away from backsplash then slide handle back onto valve stem (). Insert holding screw with washer and tighten. Slide Hot and old Indicator Ring onto handle and thread metal cap back into place. To adjust handle tension, turn ring () clockwise to increase or counterclockwise to decrease. On some kitchen countertops, the handle may hit the backsplash when the faucet handle is positioned to the left or right (ig. 1). Waterstone gives you the option of adjusting the handle 22.5 degrees to avoid hitting backsplash. ONNTIN SUPPLY HOSS efore connecting supply hoses, flush supply stops to clear any debris. Place a bucket underneath stops and run water for 5 to 10 seconds. Turn water off. arefully position hot and cold supplies so they will not interfere with other hoses. onnect supply hoses () to supply stops (). O NOT use teflon tape or plumbers putty. Turn water back on and check for leaks. OPTIONL HOT OL INITOR RIN To reverse, or remove Hot and old Indicator Ring, unscrew the metal cap, remove ring and H flip. Slide ring back onto handle and screw metal cap back on. R OR HOT LU OR OL ONNTIN SI SPRY (OPTIONL) OUNTR Insert side spray base () into hole of your sink or counter. (No plumbers putty is required). Slide brass spacer () onto shroud. Screw on attaching nut () and securely tighten. Slide sidespray hose () through side spray base. Turn off water supply. On the faucet, remove cap () from end of sidespray tube (). onnect and tighten sidespray hose to sidespray tube.
INSTLL SOP/LOTION ISPNSR (OPTIONL) 1. 2. 3. Pull and remove spout () from dispenser body (). Remove clamp nut () and brass spacer () from threaded shroud. OUNTR 1-3/8 HOL it dispenser body through 1-3/8 hole on counter or sink. (No plumbers putty is required). Slide brass spacer onto shroud. Screw clamp nut and tighten snug. ill plastic bottle with soap or lotion. Thread bottle () into bottom of dispenser shroud. 4. 5. 6. Insert open end of red tubing down through dispenser base and into plastic bottle. Push down on spout to secure over white O-rings. Slide red tubing () into tube fitting () at bottom of spout. Pump spout a few times to get soap or lotion flowing. INSTLL IR SWITH (OPTIONL) 1-1/2 HOL XPOS THRS OUNTR efore inserting air switch into hole, loosen switch base () until threads are exposed. Slide clear tubing () into tube fitting () at bottom of air switch shroud. it air switch and tubing through 1-1/2 hole on counter or sink. (No plumbers putty is required. O-ring seals base). Slide washer up then screw the clamp nut onto threaded shroud. Hand tighten nut to underside of sink or counter until snug. ONTINU ON NXT P
ONTINU ROM PRVIOUS P 5. 6. 7. 8. R ISPOSL Tighten clamp screws () securely with screwdriver. Hand tighten switch base back down to cover threads. Slide other end of tubing () into tube fitting at bottom of control box (). Plug control box into undersink electrical outlet. Plug garbage disposal into either dual outlet. INSTLL SINL PORT IR P (OPTIONL) 1. 2. 3. 1-1/2 HOL Twist and pull air gap cover () off of upper cap nut (). Unscrew and remove cap nut from piping (). Unscrew and remove top clamp nut () from both threadings on piping. Slide gasket () off piping and remove. rom underneath counter top, fit air gap piping upward through 1-1/2 hole. 4. 5. 6. Slide gasket down and screw top clamp nut back onto piping. djust the two clamp nuts to fit countertop thickness. (No plumbers putty is required). Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. e sure to have overflow holes () facing sink. Slide small intake hose () over small connector. Slide larger drainage hose (H) over large connector. Tighten hose clamps. Turn on water supply and check for leaks. H
INSTLL UL PORT IR P (OPTIONL) 1-1/2 HOL Pull air gap () off of upper cap nut (). Unscrew and remove cap nut from piping (). Unscrew and remove top clamp nut () from both threadings on piping. Slide gasket () off piping and remove. rom underneath counter top, fit air gap piping upward through 1-1/2 hole. Slide gasket down and screw top clamp nut back onto piping. djust the two clamp nuts to fit countertop thickness. (No plumbers putty is required). 5. 6. Screw cap nut back onto top of piping until snug. Slide air gap over cap nut and top clamp nut. e sure to have overflow holes () facing sink. J Slide small intake hose () over small connector. Slide larger drainage hose (H) over large connector. Tighten hose clamps. H M L K Third intake hole (J) has 3 options. Use hose connector (K) for additional dishwasher, use filtration hose connector (L) for reverse osmosis unit, or use solid cap (M) to plug third hole. 41180 Raintree ourt Murrieta, 92562 1-888-304-0660 951-304-0520 www.waterstoneco.com VN-038-KP Rev.