User & Installation Manual

User & Installation Manual intarblock MCV-N, MCV-C BCV-N, BCV-C MCV-I, BCV-I intartop MCR-N, MCR-C BCR-N, BCR-C Doc. CV / CR 3.3 January 2018

I. Quick Start Guide Congratulations! You have acquired a high quality cooling unit. Your INTARBLOCK and INTARTOP units are specially designed to equip positive temperatura cold romos in the range from -5ºC (23ºF) to +10 ºC (50ºF), and from -15ºC (5ºF) to -25ºC (13ºF), depending on the range. Once installed, your INTARSPLIT unit can be fully operated from the remote keyboard. The control keyboard has the following functions and characteristics. DIGITAL DISPLAY It shows the room temperature. By pressing the set key it will show the target temperature. Press to visualise maximum temperature record Press to visualise minimum temperature record Press to visualise the target temperature, which can be modified by pressing or Operation LEDs Press for 3 seconds to force a defrost cycle Press to switch on and off the room light Press for 3 seconds to activate the energy saving function Press to turn on and off the unit The unit has four operation modes: Refrigeration mode.- this is the normal operation mode. The display shows the room temperature and by pressing the set key the target temperature is shown. During the operation the electronic control keeps a record of the maximum and minimum room temperature ever measured, which can be consulted at any time. Defrost mode.- the time on time your unit will switch to the defrost mode to eliminate the frost that has formed on the evaporator. You can also force a defrost cycle by pressing the corresponding key. Fast cooling mode.- If you like you can activate this operation mode during the start-up of the cold room. The unit will run continuously for the preset time in parameter CCt, even beyond the target temperature. Energy saving mode.- If you like you can activate or deactivate this operation mode to save energy during the night or when the room will stay closed for a long time. By activating this function the target temperature is increased according to preset value in parameter HES. 2

intarblock intartop Basic keyboard functions.- To switch ON and OFF the instrument. To switch ON and OFF the room light. To visualise maximum room temperature record In programming mode it increases the displayed value or explores the parameter list. by pressing the key for 3 seconds the fast cooling cycle starts. To visualise minimum room temperature record In programming mode it decreases the displayed value or explores the parameter list. To display and modify target set point; in programming mode it selects a parameter or confirm an operation. By holding it pressed for 3s when max or min temperature is displayed it will be erased. By holding it pressed for 3s a manual defrost cycle starts. By holding it pressed for 3s Energy Saving function is activated or deactivated. II. CONTENTS 1. DESCRIPTION... 4 2. IDENTIFICATION... 4 3. OPERATION... 5 4. OPERATION LIMITS... 6 5. COMPOSITION... 7 6. TESTS... 8 7. SAFETY DEVICES... 8 8. MCV SERIES TECHNICAL FEATURES... 9 9. BCV SERIES TECHNICAL FEATURES... 11 10. MCR SERIES TECHNICAL FEATURES... 12 11. BCR SERIES TECHNICAL FEATURES... 14 12. COOLING CAPACITY R404A... 15 13. COOLING CAPACITY R134a... 15 14. DIMENSIONS... 18 15. ELECTRICAL CONNECTIONS... 20 16. EMERGENCY SYSTEM... 21 17. SOUND PRESSURE LEVEL... 21 18. TRANSPORT... 21 19. DATA PLATE... 22 20. SAFETY RECOMMENDATIONS... 22 21. INSTALLATION AND MOUNTING... 23 22. START-UP... 27 23. MAINTENANCE... 28 24. REFRIGERANT LOAD... 29 25. DISPOSAL MANAGEMENT... 30 26. CONTROL... 30 27. PARAMETER LIST... 33 28. FAULT ANALYSIS... 37 29. GUARANTEE... 40 3

1. DESCRIPTION INTARBLOCK and INTARTOP units are monoblock refrigeration units in vertical and roof construction, fullly tested and adjusted in Factory. They are assembled on a prelacquered galvanised steel shell and have been designed for indoor installation, with easily removable panels to give access to fans, refrigerant circuit, and electric board. INTARBLOCK: MCV Series are designed for positive temperature refrigeration applications from -5ºC (23ºF) to +10ºC (50ºF) and consist of 12 models to cover a cooling capacity range from 0.5 kw to 3 kw BCV Series are designed for positive temperature refrigeration applications from -15ºC (5ºF) to -25ºC (13ºF) and consist of 9 models to cover a cooling capacity range from 0.4 kw to 2,5 kw INTARTOP: MCV Series are designed for positive temperature refrigeration applications from -5ºC (23ºF) to +10ºC (50ºF) and consist of 10 models to cover a cooling capacity range from 0.5 kw to 2,5 Kw BCR Series are designed for positive temperature refrigeration applications from -15ºC (5ºF) to -25ºC (13ºF) and consist of 6 models to cover a cooling capacity range from 0.4 kw to 1,7 kw - NF version featuring axial condensation fan, - CF version featuring centrifugal condensation fan for ducted air extraction. 2. IDENTIFICATION INTARBLOCK and INTARTOP series are identified according to the following nomenclature on the product data plate. M C V - N F - 1 024 Compressor capacity Construction size R-404A refrigerant (N) Standard (C) Centrifugal Vertical construction Compact construction Medium temperature 4

intarblock intartop 3. OPERATION INTARBLOCK and INTARTOP are refrigeration machines operating under a vapour compression cycle. Refrigeration cycle The refrigeration cycle uses a phase change refrigerant fluid in a closed circuit, with the following four steps: Expansion: refrigerant expansion takes place in the capillary tube between high and low pressure sections. During the expansion, liquid refrigerant cools down to the evaporating temperature. Evaporation: In the evaporator the refrigerant evaporates under constant temperature and pressure absorbing heat from the cold room. Once the refrigerant vapour has been fully evaporated, it is slightly overheated beyond the evaporation temperature. Compression: The resultant refrigerant vapour is suctioned from the evaporator by the compressor through the suction line. The compressor compresses the refrigerant vapour up to high pressure and temperature. Condensation: the hot high pressure gas is desuperheated and condensed, at a constant pressure and temperature, in the el condenser by exhausting the latent evaporation to the outer ambient. Once the refrigerant has been fully condensed, the liquid refrigerant is overcooled beyond the condensing temperature. High pressure liquid refrigerant is then driven to the capillary tube, and therefore closing the circuit. Defrost cycle Because of the evaporator temperature can be below 0ºC (32ºF), frost is likely to deposit on the evaporator surface through the condensation of the water vapour contained in the air. To prevent the air flow from being obstructed with the consequently loss of performance, the instrument switches automatically to the defrost operation mode every given period of time. During the defrost cycle, by opening the solenoid valve, part of the hot gas from the compressor discharge is injected into the evaporator. The evaporator temperature is rapidly increased in order to melt the frost on it while the inside fan is off. The defrost water is collected in the drain tray and conducted to the drain bucket. This drain bucket contains a hot gas coil to progressively evaporate the drain water to the outer ambient. 5

CONDENSER CAPILLARY TUBE / THERMOSTATIC EXPANSION VALVE EVAPORATOR FILTER DRAIN TRAY COMPRESSOR SOLENOID VALVE AP BP DRAIN BUCKET PRESSURE REGULATOR (only BCV/BCR) 4. OPERATION LIMITS INTARBLOCK and INTARTOP units are designed for continuous operation within the following temperature limits: Cold Room Temperature Ambient Temperature Max Min Max Min MCV +10 ºC (50ºF) -5 ºC (23ºF) +45 ºC (113ºF) +15 ºC (59ºF) BCV -15 ºC (5ºF) -25 ºC (-13ºF) +45 ºC (113ºF) +15 ºC (59ºF) MCR 10 ºC (50ºF) -5 ºC (23ºF) +45 ºC (113ºF) +15 ºC (59ºF) BCR -15 ºC (5ºF) -25 ºC (-13ºF) +45 ºC (113ºF) +15 ºC (59ºF) The unit should work beyond these limits only for short periods of time or during the start-up. 6

intarblock intartop 5. COMPOSITION MCV / BCV units are built on a self-contained construction. The components are assembled on a steel structure and covered with a prelacquered galvanised steel shell. It consists of: Refrigerant circuit Hermetic reciprocating compressor with internal protection, assembled on silentblocs R404-A or R134a refrigerant load. HP and LP pressure switches. HP and LP load nipples. Thermostatic expansion valve (capillary tube in medium temperature models with power lower than 1,5 HP (R404A) and 1 HP (R134a). Antiacid dehydrating filter. Evaporation coil in copper tubes and aluminium fins with stainless steel drain tray. Condensation coil in copper tubes and aluminium fins. Solenoid valve for the hot gas bypass. Water drain bucket including hot gas coil for the automatic evaporation of drain water. Air circuits N/I version: Direct driven axial fans with single phase motor. Dynamically equilibrated blades with protection grill. C version: Direct driven centrifugal fans with single phase motor. Dynamically equilibrated rotor. Electric board Circuit breaker protection Electric control XW270K with the following elements and features: - transformer 230 VAC / 12 VCC, - microprocessor, - alarm relay, - compressor relay, - defrost relay, - evaporator fan relay, - cold room light relay, - condenser fan relay, - door switch digital input - H/LP pressure switch input - inside temperature NTC probe - outside temperature NTC probe - defrost NTC probe - RS485 connection, - programming key connection, 7

- V820 keyboard. Compressor permanent condenser in single phase units. Compressor start relay and condenser in single phase units. Ground connection for compressor and motorfans. Cold room light. Door microswitch connection. Door microswitch (as an option). Door heating cable (only for BCV and BCR models). Crankcase heater (as an option). Draining pipe heating cable (only for BCV y BCR models). 6. TESTS Every INTARBLOCK and INTARTOP units have been previously checked and tested in factory according to the following test protocol: Helium leak-proof test. A leak-proof certificate is supplied upon request. Refrigerant load. Operation test for refrigeration and defrost modes under nominal operating conditions. Safety devices checking 7. SAFETY DEVICES INTARBLOCK and INTARBLOCK units feature the following safety devices: HP and LP pressure limit switches to protect the unit against unusual pressure levels. Thermal switches with automatic restart in compressor and fans to protect motor wirings from overloads. Circuit breaker protection Common ground connection. 8

8. MCV SERIES TECHNICAL FEATURES intarblock intartop MCV Series R404A 0008 0010 0012 1010 1012 1014 1016 1018 1024 2024 2026 2034 3034 3038 Cooling capacity Cooling capacity (1) (W) 610 728 808 799 930 1077 1184 1347 1468 1917 2149 2391 2690 3020 Absorbed power (2) (W) 470 570 640 649 672 804 869 1020 1175 1356 1474 1946 2070 1970 COP performance 1,30 1,28 1,27 1,23 1,38 1,34 1,36 1,32 1,25 1,41 1,46 1,23 1,30 1,53 Installed power (3) (kw) 0,53 0,73 0,86 0,75 0,82 0,98 1,10 1,38 1,68 1,68 1,89 2,63 2,63 2,35 Condenser fan NF version Condenser fan CF version Evaporator fan Nominal air flow rate (m3/h) 375 575 1000 1350 Axial Power (W) - r.p.m 85W @ 1300 2 x 85W @ 1300 2x70W@1300 Nominal air flow rate (m3/h) 575 1000 1350 Available static pressure (Pa) 45 90 120 - Centrifugal Power (W) 45 W 105 W 2 x 105 W Nominal air flow rate (m3/h) 300 550 1050 1400 Range (m) 3 4 Axial Power (W) - r.p.m 47W @ 2500 62W @ 2600 2 x 62W @ 2600 2x70W@2600 Hermetic reciprocating Swept volume (m3/h) 1,16 1,54 1,79 1,64 1,96 2,32 2,65 3,18 4,21 4,21 4,52 6,01 6,01 6,60 Compressor Nominal discharge pressure (bar rel.) Nominal suction pressure (bar rel.) 20 3,40 Nominal power (CV) 1/3 3/8 1/2 3/8 1/2 1/2 5/8 3/4 1 1 1 1/4 1 1/2 1 1/2 1 3/4 High pressure switch Max. absorbed intensity (A)(4) Starting-up intensity (A) Refrigerant Dimensions ACB Brand Danfoss Model 061F8175 Cut out (bar rel.) 28 230 V / I ph / 50 Hz 4,5 5,9 6,7 5,1 6,1 6,7 7,6 8,9 11,1 11,9 12,3 16,9 17,1 N/D 400 V / III ph / 50 Hz Not available 5,7 6,5 6,7 7,9 230 V / I ph / 50 Hz 16,3 18,8 20,2 16,9 17,9 20,9 23,5 30,9 34,4 35,2 33,7 46,7 46,9 N/D 400 V / III ph / 50 Hz Not available 19,7 24,7 24,9 17,9 R-404A / Group L1 / GWP-100: 3922 Load (kg) 0,50 0,50 0,56 0,70 0,70 0,70 0,78 0,76 0,76 1,00 0,98 1,10 1,66 1,50 Length (mm) 556 854 854 879 Wide (mm) 420 400 620 735 Height (mm) 683 880 920 920 Weight (kg) 35 37 38 59 60 60 69 70 70 88 89 89 117 114 Sound pressure level db(a) 30 30 30 31 31 32 34 35 35 36 38 40 39 40 (1) Cooling capacity under cold room temperature of 0 ºC (32 ºF) and ambient temperature of 35 ºC (95 ºF). (2) Total absorbed power by compressor and fans under nominal condition (axial version). (3) As defined by RD138/2011. IF-01. (4) Maximum absorbed current even beyond compressor operation limits (axial version). 9

MCV series R134a 0010 0015 1015 1026 1033 2033 2053 3053 3074 3108 Cooling capacity (1) (W) 610 794 972 1281 1454 1790 2153 2489 3239 3927 Cooling capacity Absorbed power (2) (W) 430 530 570 810 920 1090 1460 1510 1890 2480 COP performance 1,42 1,50 1,71 1,58 1,58 1,64 1,47 1,65 1,71 1,58 Installed power (3) (kw) 0,59 0,83 0,83 1,22 1,44 1,44 2,2 2,2 2,9 4,4 Nominal air flow rate (m3/h) 375 575 950 1150 Condenser fan NY version Power (W) - r.p.m 85 W @ 1300 Axial 2x 85 W @ 2x 70 W @ 1300 1300 Nominal air flow rate (m3/h) 375 575 950 1150 Condenser fan CY version Available static pressure (Pa) 120 Centrifugal Power (W) 180 W 220 W 2x 200W 2x 200W Nominal air flow rate (m3/h) 300 500 950 1300 Evaporator fan Range (m) 3 4 Axial Power (W) - r.p.m 47W @ 2500 62W @ 2600 2x 62W @ 2x 70W @ 2600 2600 Hermetic reciprocating Swept volume (m3/h) 2,08 3,18 3,18 4,51 5,69 5,69 9,26 9,26 12,92 18,74 Compressor Nominal discharge pressure (bar rel.) 10 Nominal suction pressure (bar rel.) 1 Nominal power (CV) 3/8 1/2 1/2 3/4 1 1 1 1/2 1 1/2 2 5 Brand High pressure switch Model ACB Danfoss 061F6147 Cut out (bar rel.) 20 Max. absorbed intensity (A)(4) Starting-up intensity (A) Refrigerant 230 V / I ph / 50 Hz 5,9 6,9 7,0 10,7 10,9 11,1713,7714,19 19,74-400 V / III ph / 50 Hz Not available 18,5 230 V / I ph / 50 Hz 13,2 20,7 20,7 27,0 30,0 30,0 46,0 46,0 55,0-400 V / III ph / 50 Hz Not available 65 R-134a / Group A1 / GWP-100: 1430 Load (kg) 0,56 0,62 0,64 0,64 0,70 0,90 0,90 1,30 1,20 1,40 Length (mm) 306+250 340+514 340+514 365+514 Dimensions Wide (mm) 420 400 620 735 Height (mm) 683 880 920 940 Weight (kg) 36 38 60 69 70 88 89 117 114 116 Sound pressure level db(a) 28 29 29 34 34 35 39 38 41 43 (1) Cooling capacity under cold room temperature of 0 ºC (32 ºF) and ambient temperature of 35 ºC (95 ºF). (2) Total absorbed power by compressor and fans under nominal condition (axial version). (3) As defined by RD138/2011. IF-01. (4) Maximum absorbed current even beyond compressor operation limits (axial version). 10

intarblock intartop 9. BCV SERIES TECHNICAL FEATURES BCV Series R404A 0018 1018 1026 1034 2034 2054 2074 3074 3086 3096 Cooling capacity (1) (W) 479 489 720 866 1048 1349 1633 1930 2270 2460 Cooling capacity Absorbed power (2) (W) 620 688 914 1136 1187 1685 2014 2380 2320 2640 COP performance 0,77 0,73 0,79 0,76 0,88 0,80 0,81 0,81 0,98 0,93 Installed power (3) (kw) 0,87 0,88 1,29 1,76 1,76 2,60 3,39 3,39 3,46 4,31 Nominal air flow rate (m3/h) 375 575 1000 1350 Condenser fan NF version Axial Power (W) - r.p.m 85W @ 1300 2 x 85W @ 1300 2 x 70W @ 1300 Nominal air flow rate (m3/h) 575 1000 1350 Condenser fan Available static pressure (Pa) 45 90 120 - CF version Centrifugal Power (W) 45 W 105 W 2 x 105 W Nominal air flow rate (m3/h) 300 550 1050 1400 Range (m) 3 4 Evaporator fan Axial Power (W) - r.p.m 47W @ 2500 62W @ 2600 2 x 62W @ 2600 2 x 70W @ 2600 Hermetic reciprocating Swept volume (m3/h) 3,18 3,18 4,57 6,01 6,01 9,25 12,91 12,91 11,80 16,70 Compressor Nominal discharge pressure (bar rel.) 20 Nominal suction pressure (bar rel.) 1,30 Nominal power (CV) 5/8 5/8 3/4 1 1/4 1 1/4 1 3/4 2 1/2 2 1/2 3 3 1/2 High pressure switch Brand Model ACB Danfoss 061F8175 Cut out (bar rel.) 28 Max. absorbed intensity (A)(4) Starting-up intensity (A) Refrigerant 230 V / I ph / 50 Hz 4,8 7,2 8,4 10,9 11,7 17,7 25,7 25,9 No disponible 400 V / III ph / 50 Hz Not available 6,5 7,2 7,4 10,3 12,0 230 V / I ph / 50 Hz 21,9 21,9 29,9 40,9 41,7 69,7 82,7 82,9 No disponible 400 V / III ph / 50 Hz Not available 24,7 29,7 29,9 26,9 33,9 R-404A / Group L1 / GWP-100: 3922 Load (kg) 0,60 0,70 0,70 0,60 1,15 1,05 1,10 1,50 1,50 1,20 Length (mm) 556 854 854 879 Dimensions Wide (mm) 420 400 620 735 Height (mm) 683 880 920 920 Weight (kg) 38 59 60 60 89 102 102 131 117 129 Sound pressure level db(a) 33 38 38 40 41 42 43 43 40 50 (1) Cooling capacity under cold room temperature of -20 ºC (-4 ºF) and ambient temperature of 35 ºC (95 ºF). (2) Total absorbed power by compressor and fans under nominal condition (axial version). (3) As defined by RD138/2011. IF-01. (4) Maximum absorbed current even beyond compressor operation limits (axial version). 11

10. MCR SERIES TECHNICAL FEATURES MCR Series R404A 0008 0010 0012 1010 1012 1014 1016 1018 1024 2024 2026 2034 Cooling capacity Cooling capacity (1) (W) 612 738 838 799 930 1087 1194 1378 1478 2020 2223 2527 Absorbed power (2) (W) 470 580 650 652 672 811 880 1038 1201 1319 1425 1903 COP performance 1,30 1,27 1,29 1,23 1,38 1,34 1,36 1,33 1,23 1,53 1,56 1,33 Installed power (3) (kw) 0,53 0,73 0,86 0,75 0,82 0,98 1,10 1,38 1,68 1,68 1,89 2,63 Condenser fan NF version Condenser fan CF version Evaporator fan Nominal air flow rate (m3/h) 375 575 1150 Power (W) - r.p.m 85 W @ 1300 rpm 120W @ 1300 rpm Nominal air flow rate (m3/h) Axial 575 1150 Available static pressure (Pa) 45 - Centrifugal Power (W) 45 W @ 1300 rpm 105 W @ 1300 rpm Nominal air flow rate (m3/h) 300 600 1150 Range (m) 3 4 Axial Power (W) - r.p.m 47@ 2500 rpm 62W @ 2600 rpm 2x 62W @ 2600 rpm Hermetic reciprocating Swept volume (m3/h) 1,16 1,54 1,79 1,64 1,96 2,32 2,65 3,18 4,21 4,21 4,52 6,01 Compressor Nominal discharge pressure (bar rel.) Nominal suction pressure (bar rel.) 20 3,40 Nominal power (CV) 1/3 3/8 1/2 3/8 1/2 1/2 5/8 3/4 1 1 1 1/4 1 1/2 High pressure switch Brand Model ACB Danfoss 061F8175 Cut out (bar rel.) 28 Max. Absorbed intensity(4)(a) Starting up intensity (A) Refrigerant 230 V / I ph / 50 Hz 4,5 5,9 6,7 5,1 6,1 6,7 7,6 8,9 11,1 11,6 12,0 16,6 400 V / III ph /50 Hz Not available 5,4 6,2 230 V / I ph / 50 Hz 16,3 18,8 20,2 16,9 17,9 20,9 23,5 30,9 34,4 34,9 33,4 46,4 400 V / III ph /50 Hz Not available 19,4 24,4 R-404A / Group L1 / GWP-100: 3922 Load (kg) 0,50 0,50 0,50 0,80 0,70 0,80 0,83 0,76 0,86 1,10 1,05 1,10 Length (mm) 790 850 850 Dimensions Wide (mm) 600 665 835 Height (mm) 480 385+189 468+189 Weight (kg) 62 64 65 73 73 73 82 83 83 98 99 99 Sound pressure level db(a) 30 30 30 32 32 32 34 35 35 36 38 40 (1) Cooling capacity under cold room temperature of 0 ºC (32 ºF) and ambient temperature of 35 ºC (95 ºF). (2) Total absorbed power by compressor and fans under nominal condition (axial version). (3) As defined by RD138/2011. IF-01. (4) Maximum absorbed current even beyond compressor operation limits (axial version). 12

intarblock intartop MRC series R134a 0010 0015 1015 1026 1033 2033 2053 2074 Cooling capacity (1) (W) 605 788 999 1265 1502 1911 2352 2940 Cooling capacity Absorbed power (2) (W) 430 530 580 930 1050 1210 1670 1830 COP performance 1,41 1,48 1,72 1,36 1,43 1,58 1,41 1,61 Installed power (3) (kw) 0,83 0,83 1,22 1,44 1,44 2,2 2,9 Condenser fan NF version Nominal air flow rate (m3/h) 375 575 1000 Axial Power (W) - r.p.m 85 W @ 1300 120 W @ 1300 Nominal air flow rate (m3/h) 375 575 1000 Condenser fan CF version Available static pressure (Pa) 120 Centrifugal Power (W) 180 W 220 W 2x 200 W Nominal air flow rate (m3/h) 300 600 1150 Evaporator fan Range (m) 4 Axial Power (W) - r.p.m 47W @ 2500 62W @ 2600 2x 62W @ 2600 Hermetic reciprocating Swept volume (m3/h) 2,08 3,18 3,18 4,51 5,69 5,69 9,26 12,92 Compressor Nominal discharge pressure (bar rel.) 10 Nominal suction pressure (bar rel.) 1 Nominal power (CV) 3/8 1/2 1/2 3/4 1 1 1 1/2 2 High pressure switch Brand Model ACB Danfoss 061F6147 Cut out (bar rel.) 20 Max. Absorbed intensity(4)(a) Starting up intensity (A) Refrigerant 230 V / I ph / 50 Hz 5,94 6,94 7,00 10,70 10,90 11,17 13,7 11,77 400 V / III ph /50 Hz Not available 230 V / I ph / 50 Hz 16 22 22 29 30 30 46 55 400 V / III ph /50 Hz Not available R-134a / Grupo A1 / PCA-100: 1430 Load (kg) 0,46 0,50 0,70 0,70 0,60 1,00 1,00 1,10 Length (mm) 790 850 850 Dimensions Wide (mm) 600 665 835 Height (mm) 330+100 385+135 469+135 Weight (kg) 62 65 73 82 83 98 99 110 Sound pressure level db(a) 30 30 28 34 34 35 39 41 (1) Cooling capacity under cold room temperature of 0 ºC (32 ºF) and ambient temperature of 35 ºC (95 ºF). (2) Total absorbed power by compressor and fans under nominal condition (axial version). (3) As defined by RD138/2011. IF-01. (4) Maximum absorbed current even beyond compressor operation limits (axial version). 13

11. BCR SERIES TECHNICAL FEATURES BCR Series R404A 0008 1018 1026 1034 2034 2054 2074 Cooling capacity (1) (W) 515 502 734 876 1102 1443 1689 Cooling capacity Absorbed power (2) (W) 630 671 928 1160 1297 1830 2147 COP performance 0,81 0,75 0,79 0,76 0,85 0,79 0,79 Installed power (3) (kw) 0,87 0,88 1,29 1,76 1,76 2,60 3,39 Nominal air flow rate (m3/h) 375 575 1150 Condenser fan NF version Axial Power (W) - r.p.m 85 W @ 1300 rpm 120 W @ 1300 rpm Nominal air flow rate (m3/h) 575 1150 Condenser fan Available static pressure (Pa) 45 - CF version Centrifugal Power (W) 45 W @ 1300 rpm 105 W @ 1300 rpm Nominal air flow rate (m3/h) 300 600 1150 Evaporator fan Range (m) 3 4 Power (W) - r.p.m 47 W @ 2500rpm Axial 62 W @ 2600 rpm 2 x 62 W @ 2600 rpm Hermetic reciprocating Swept volume (m3/h) 3,18 3,18 4,57 6,01 6,01 9,25 12,91 Compressor Nominal discharge pressure (bar rel.) 20 Nominal suction pressure (bar rel.) 1,30 Nominal power (CV) 5/8 5/8 3/4 1 1/4 1 1/4 1 3/4 2 1/2 High pressure switch Brand Model ACB Danfoss 061F8175 Cut out (bar rel.) 28 Max. absorbed intensity (A) Starting-up intensity (A) Refrigerant 230 V / I ph / 50 Hz 4,8 7,2 8,4 10,9 11,4 17,4 25,4 400 V / III ph / 50 Hz Not available 6,21 6,91 230 V / I ph / 50 Hz 21,9 21,9 29,9 40,9 41,4 69,4 82,4 400 V / III ph /50 Hz Not available 24,4 29,4 R-404A / Grupo L1 / PCA-100: 3260 Load (kg) 0,64 0,75 0,75 0,80 1,20 1,00 1,10 Length (mm) 790 850 850 Dimensions Wide (mm) 600 665 835 Height (mm) 480 385+189 468+189 Weight (kg) 65 83 84 84 135 145 145 Sound pressure level db(a) 33 38 38 40 41 42 43 (1) Cooling capacity under cold room temperature of 0 ºC (32 ºF) and ambient temperature of 35 ºC (95 ºF). (2) Total absorbed power by compressor and fans under nominal conditions. (3) As defined by RD138/2011. IF-01. (4) Maximum absorbed current even beyond compressor operation limits (axial version) 14

intarblock intartop 12. COOLING CAPACITY R-404A MCV series Ambient Temp: 35 ºC Capacity (W) MCV series Cooling capacity (W) Cold room temperature -5 ºC 0 ºC +5 ºC +10 ºC Cooling Cooling Cooling Absorbed Absorbed Absorbed capacity capacity capacity power (W) power (W) power (W) (W) (W) (W) Absorbed power (W) 0008 502 446 610 470 738 506 860 534 0010 604 533 728 570 871 624 1012 666 0012 568 619 808 676 961 706 1118 759 1010 630 613 801 649 966 683 1157 722 1012 767 631 930 672 1118 714 1317 763 1014 893 756 1077 804 1270 858 1485 920 1016 985 800 1184 869 1386 939 1615 1018 1018 1138 940 1347 1020 1570 1104 1806 1200 1024 1207 1049 1468 1175 1739 1305 2039 1450 2024 1554 1245 1917 1356 2296 1464 2726 1579 2026 1795 1368 2149 1474 2526 1584 2945 1707 2034 1996 1805 2391 1946 2801 2102 3247 2282 3034 2230 1925 2690 2070 3200 2220 3730 2390 3038 2500 1830 3020 1970 3580 2110 4220 2270 BCV series Ambient Temp: 35 ºC Capacity (W) MCV series Cooling capacity (W) Cold room temperature -25 ºC -20 ºC -15 ºC Absorbed power (W) Cooling capacity (W) Absorbed power (W) Cooling capacity (W) Absorbed power (W) 0018 379 565 479 620 591 694 1018 383 611 489 668 655 747 1026 548 802 720 914 877 1015 1034 668 986 866 1136 1023 1254 2034 793 1196 1048 1334 1297 1463 2054 963 1592 1349 1832 1655 2026 2074 1338 1931 1633 2161 1963 2405 3074 1430 2070 1930 2380 2320 2660 3086 1630 2000 2270 2320 2810 2560 3096 1890 2280 2460 2640 3040 2970 15

MCR Series Ambient Temp.: 35 ºC Capacity (W) MCR Series Cooling capacity (W) Cold room temperature -5 ºC 0 ºC +5 ºC +10 ºC Absorbed power (W) Cooling capacity (W) Absorbed power (W) Cooling capacity (W) Absorbed power (W) Cooling capacity (W) Absorbed power (W) 0008 508 455 612 470 720 521 851 547 0010 621 537 738 580 901 629 1055 681 0012 701 598 838 650 1012 712 1163 766 1010 630 617 801 652 966 682 1157 727 1012 767 637 930 672 1118 717 1317 772 1014 916 761 1087 811 1275 867 1479 929 1016 1005 811 1194 880 1402 953 1628 1031 1018 1161 957 1378 1038 1579 1118 1828 1211 1024 1217 1070 1478 1201 1782 1335 2062 1462 2024 1625 1201 2020 1319 2402 1409 2888 1527 2026 1849 1324 2223 1425 2646 1531 3077 1648 2034 2080 1768 2527 1903 2987 2059 3380 2190 BCR Series Ambient Temp: 35 ºC Capacity (W) Cold room temperature -25 ºC -20 ºC -15 ºC BCR Series Cooling Absorbed power Cooling capacity Absorbed power Cooling capacity Absorbed power capacity (W) (W) (W) (W) (W) (W) 0018 405 570 515 630 618 700 1018 407 618 502 671 664 752 1026 565 813 734 928 908 1039 1034 699 1015 876 1160 1051 1287 2034 840 1157 1102 1297 1366 1433 2054 1116 1617 1443 1830 1733 2005 2074 1425 1932 1689 2147 2088 2416 16

intarblock intartop 13. COOLING CAPACITY R-134a Serie MCV Ambient Temp: 35 ºC Cold room temperature Capacity (W) 0 ºC +5 ºC +10 ºC MCV Series Cooling Absorbed Cooling Absorbed Cooling Absorbed capacity (W) power (W) capacity (W) power (W) capacity (W) power (W) 0010 610 437 758 477 907 508 0015 794 532 961 587 1139 642 1015 972 572 1199 622 1453 672 1026 1281 812 1565 892 1859 972 1033 1454 922 1743 1012 2037 1112 2033 1790 1099 2163 1184 2573 1274 2053 2153 1464 2609 1634 3103 1809 3053 2489 1515 3103 1700 3743 1870 3074 3239 1895 3938 2145 4667 2400 3108 3927 2485 4725 2790 5539 3145 Serie MCR Cold room temperature Capacity (W) 0 ºC +5 ºC +10 ºC MCR Series Cooling Absorbed Cooling Absorbed Cooling Absorbed capacity (W) power (W) capacity (W) power (W) capacity (W) power (W) 0010 605 432 751 471 902 505 Ambient Temp: 35 ºC 0015 788 530 956 577 1134 640 1015 999 580 1231 673 1490 691 1026 1265 930 1549 884 1853 970 1033 1502 1050 1817 1067 2153 1176 2033 1911 1210 2363 1210 2846 1347 2053 2352 1670 2882 1689 3455 1855 2074 2940 1830 3560 1945 4211 2147 17

14. DIMENSIONS CV-N-C Models Centrifugal Box only in 0 series PLUG-IN FRAME DROP FRAME Dimensions (mm) A B C D E F G H I J K L M Exhaust duct 0 series 306 510 683 420 250 50 405 515 n/a Ø 150 1 series 340 330 880 400 514 122 380 335 75 41 295 13 233 Ø 150 2 series 340 330 920 620 514 122 600 335 75 36 523 13 233 Ø 150 3 series 365 470 920 735 514 122 710 475 75 41 611 22 356 2x Ø 150 CV-I Models Dimensions (mm) A B C D E F G H 1 series 340 330 1060 400 514 115 380 335 2 series 340 330 1100 620 514 115 600 335 3 series 365 470 1100 735 514 115 710 475 18

intarblock intartop CR-N Models ROOF FRAME CR-C Models Dimensions (mm) A B C D E F G H I Exhaust duct 0 series 480 600 430 330 790 375 100 435 380 Ø 150 1 series 574 665 582 385 850 379 135 588 385 Ø 150 2 series 677 835 756 469 850 379 135 762 385 Ø 150 19

15. ELECTRICAL CONNECTIONS Before connecting the unit to the electrical supply, make sure that the electrical board is in good conditions and please follow the following recommendations: Consult the electrical schema supplied by manufacturer. Only use electrical cables of the appropriate characteristics and capacity according to the following table. Notice that single phase units have a three-wire supply and three phase units have a fivewire supply, being always the ground wire in green-yellow colour. MCV - MCR 0008 0010 0012 1010 1012 1014 1016 1018 1024 2024 2026 2034 3034 3038 Power supply 220-I-50 Power supply 400-III-50 Cold room light Door microswitch Remote controller 2 x 1,5 mm² + T 2 x 1 mm² + T 2 x 1 mm² 2 x 1 mm² 2 x 2,5 mm² + T 4 x 1,5 mm² + T BCV - BCR 0018 1018 1026 1034 2034 2054 2074 3074 3086 3096 Power supply 220-I-50 Power supply 400-III-50 Cold room light Door microswitch Remote controller Power supply 220-I-50 2 x 1,5 mm² + T 2 x 2,5 mm² + T 2 x 1 mm² + T 2 x 1 mm² 2 x 1 mm² 2 x 1 mm² 2 x 4 mm² + T 4 x 1,5 mm² + T Always install the appropriate protection device on the supply line. In case that more than one unit is installed, always provide separate protection devices for each of the installed units. Electrical wires section in power supply wiring is to be calculated according to the electrical data provided by manufacturer in data plate, power supply wires length, wires type, etc.; always according to electrical regalement. Optionally install a door switch on the end of the supplied cable or close the end of the cable. Install the room light in the supplied cable. 20

intarblock intartop 16. EMERGENCY SYSTEM The electronic regulation of the units involves control routines and emergency alarms for the following causes: Probe failure. Too high and too low room temperature. Too high or too low refrigerant pressure. Too high ambient temperature Electronic control failure Opened door. Once a failure an external alarm is activated, and the unit turns into emergency operation mode. 17. SOUND PRESSURE LEVEL Sound pressure level should be observed once the unit is installed. To do so, the environment, the type of building and the rest of the solid elements should be considered on the noise transmission. It is recommended to deploy an expert study if necesary. INTARBLOCK and INTARTOP units include low noise components. The following chart indicates sound pressure levels calculated at 10 m from the source in open field distribution (directivity = 1): 18. TRANSPORT Handle the unit with care to prevent damages during its transport. Please follow the following instructions: Always handle the unit in vertical position. Never pile up the units during transport. Never pile up the units during storage. Use a forklift or a pallet jack to handle the unit. Keep the unit on its pallet until its final destination. H Packaging dimensions (mm) L W H Weight CV series 0 610 460 823 44 Kg CV series 1 905 440 1065 76 Kg CV series 2 905 660 1105 108 Kg CV series 3 940 795 1105 137 Kg CR series 0 870 660 655 77 Kg CR series 1 920 820 700 100 Kg CR series 2 920 985 780 162 Kg A L 21

19. DATA PLATE All All units are identified with the following data plate. In all communications with the manufacturer please indicate the serial number. 20. SAFETY RECOMMENDATIONS The start-up of the unit and its reparation must be carried out by qualified personnel. To minimise the risk of accidents during the installation, start up or maintenance tasks, below instructions must be followed. It is mandatory to observe the recommendations and instructions as shown in manufacturer manuals, plates and specific instructions. It is also mandatory to observe law and regulations. Before operating on the unit, verify that the general supply is disconnected to avoid electrical shocks. Refrigerant leaks may cause: Suffocation due to oxygen displacement in the atmosphere, narcotic effect or heart arrhythmia. Ensure that the working area is properly ventilated. Eye irritations or burns may be caused if refrigerant comes into contact with the skin. Use a safety mask and a pair of gloves. Avoid any contact between the refrigerant and the skin and mind any sharp end of the unit. 22

In case of accident due to refrigerant inhalation follow the following instructions: intarblock intartop Move the victim where it could breathe fresh air. The victim should lay on its back or its shoulder. Call emergency services if needed. In case of eye injures due to refrigerant splatters: Never rub the eyes. In case contact lenses are used, you must take them out. Eyes should be kept open and washed with plenty of water. The victim should be taken to an emergency medical service In case of burn due to contact with the skin Wash with plenty of running water the affected part and take out the clothes while water is applied on. Never cover the affected parts with cloth, bandages or oil. 21. INSTALLATION AND MOUNTING The final emplacement of the unit will affect the good performance of the unit. For an optimal performance, please follow the following recommendations: During the reception of your unit, please verify that it is free from any transport damage. Otherwise indicate the perceived damages on the receipt. Install the unit in a room with good ventilation and away from heat sources. Keep clean the surroundings of the unit to facilitate the air intake and exhaust, and make sure the air does not reflow. INTARBLOCK units are designed for wall mounting directly onto the cold room panel. To do so, cut out the indicated frame on the wall panel, depending on the type of mounting. Drop mounting (except series 0).- 1. Before assembling the cold room, cut out the corresponding frame for the unit structure and drill the hole for the drain pipe in the specified position. 2. Remove the drain pipe from the drain tray. To do so screw out the side cover of the inner part and release the end of the tube. 3. Place the unit before assembling the roof of the cold room. 4. Place the drain pipe through the hole in the panel. Then, replace the roof panel. 23

RECOMMENDED SEPARATION > 500 mm DOOR HEATER (Only BCV) DOOR MICROSWITCH SIDE COVER COLD ROOM LIGHT RECOMMENDED SEPARATION 1 000 mm DRAIN PIPE Plug in mounting.- on an existing cold room or new one: 1. Cut out the indicated frame on the wall panel. 2. Place the unit into the wall frame with the supplied isolating block. RECOMMENDED SEPARATION > 500 mm DOOR HEATER (Only BCV) DOOR MICROSWITCH COLD ROOM LIGHT RECOMMENDED SEPARATION 1 000 mm INSULATING PAD Fix the unit to the wall panel by mean of 6 through screws of Ø 6 mm metric as indicated on the drawing. For the drop mounting, two hang-in holes are available for Ø 8 mm metric. 24

intarblock intartop Dimensions (mm) A B C D E F G H CV series 0 (plug-in mounting) 400 +0 +5 117 ±1 135 ±1 n/a 511 +5 C A C C A C 52 ± 1 Ø6 Ø6 Ø6 ±1 Ø6 Ø6 Ø6 12 5 72 +3 H 159 ± 1 E F F G Ø8 Ø8 Ø2 2 +2 D B Ø6 Ø6 Ø6 Ø6 Ø6 Ø6 C C C C PLUG-IN MOUNTING DROP MOUNTING Dimensions (mm) A B C D E F G H CV series 1 375 +0 +5 469 ±1 125 ±1 726.5 ±1 34.5 +5 122 ±1 208 ±2 330 +5 CV series 2 595 +0 +5 509 ±1 235 ±1 766.5 ±1 30.5 +5 222 ±1 208 ±2 330 +5 CV series 3 692 +0 +5 369 ±1 292 ±1 766.5 ±1 39.5 +5 267.5 ±1 356 ±2 470 +5 25

Centrifugal fan installation.- for CV-CF models. 1. Fix the unit to the cold room wall before installing the centrifugal fan. 2. Take out the side panels of the centrifugal box to access the fixing screws. 3. Screw the centrifugal box to the refrigeration unit and connect the fan electrical wiring. 4. Re install the side panels. The INTARTOP unit series are specially designed for roof mounting. To do so, please follow below steps: Before assembling the roof of the cold room, cut out the roof frame as indicated in the plan and dimensions chart (page 16)). Once the cold room is assembled, place the unit on the roof. RECOMMENDED SEPARATION MINIMUM 650 mm RECOMMENDED SEPARATION 500 mm CONTROL PAD WIRING COLD ROOM LIGHT DOOR MICROSWITCH POWER SUPPLY DOOR HEATER In some operation conditions (e.g. intenstive use in wet environmment, air infiltrations, etc.), it could be possible that the unit is not able to evaporate all condensing water. In that case, install a draining pipe in the drain bucket to a permanent draining point. Finally seal with silicon the gap between the unit and the wall panel. To ensure good working conditions and easy access for maintenance, please keep free the recommended separation around the unit. Condensation air ducts (CV-C and CR-C models) Units of CV-C and CR-F series feature a centrifugal condensation fan to be ducted. It is recommended to duct the air extraction. Optionally, it is also recommended to duct the air suction through semi-flexible ducts in aluminium or rigid ducts in PVC plastic, steel or fibreglass. Failing a detailed calculation, the following chart shows the recommended dimensions according to the duct type, for an equivalent total length of 20 m and both air intake-outtake grilles. 26

intarblock intartop CV/CR -C Air flow m³/h A.s.p. Pa Recommended duct dimensions (mm) Semi-flexible Rigid (PVC or steel) CV 0 series 375 120 Ø 200 Ø 150 CV 1 series 575 120 Ø 250 < 20 m: Ø 150 >20 m: Ø 200 CV 2 series 950 120 Ø 315 Ø 200 CV 3 series 1250 120 Ø 315 Ø 250 CR 0 series 375 120 Ø 200 Ø 150 CR 1 series 575 120 Ø 250 < 20 m: Ø 150 >20 m: Ø 200 CR 2 series 1150 120 Ø 315 Ø 200 It is recommended a minimum length duct, avoiding placing unnecessary turns. Failing a detailed calculation, it can be supposed that a 90º turn, with no internal radio, is equivalent to 5 m length. If air intake is not ducted, an air intake adequate to the room should be planned. It is not recommended the use of flexible ducts due to pressure loss, being only acceptable in case of straight and very short stretches. If so, an aluminium semi-flexible duct as indicated diameters is recommended. 22. START-UP Before starting the unit,plese check that the unit is properly fixed on its supports and the electrical connections are properly installed. If you have worked on the unit, take care not to forget tools or any objects inside, that there is no gas leak and that assembly-connection are properly done. Before starting up or after a stand-by periods, activating the crankage heater (when included) at twelve hours in advance is recommended. Otherwise, the compressor must be warmed up in a different way to ensure the refrigerant-oil separation. This operation is important, specially when starting-ups in low ambiance temperatures. Connect the electrical supply and switch on the unit with room door closed. The display will show the room temperature and after the time as specified for Ods parameter the compressor will start. Set the cold room temperature set point and wait until the cold room temperature reaches the set point. The high temperature alarm will not be activated until the time of dao parameter is elapsed. Once the target temperature is reached, initialise the record of maximum and minimum temperature as indicated in thism anual. You may check that auxiliary devices work properly: Room light.- turn on and off the room light. Door switch.- check that the compressor and fans stop when opening the door. Force a manual defrost cycle to check this operation mode. make sure that the evaporation coil gets clean and that the unit stays within the normal operating parameters without activating any safety device. Depending on the application you may need to modify defrost parameters, such as time period between two consecutive defrost cycles, defrost cycle duration or termination temperature. To do so, pay attention to the defrost cycles during normal operation. 27

Finally you can easily test the proper operation of some of the safety devices such as: Open door alarm.- by leaving the door open beyond indicated in doa parameter. High pressure switch or high temperature alarm.- by intentionally obstructing the air intake of condenser. Low pressure switch or Low temperature alarm.- by intentionally obstructing the air intake of evaporator. 23. MAINTENANCE INTARBLOCK and INTARTOP units are self-contained equipment not requiring specialised maintenance. Nevertheless, to keep your unit in an optimal working state, we recommend to periodically carrying out the following preventive maintenance tasks. During the maintenance tasks, switch off the power supply and use gloves to avoid any possible cut. External cleaning.- To keep your unit free from dust and dirtiness, simply pass a wet cloth over the cover. Do not use neither solvents nor detergents. BATERIA DE CONDENSER CONDENSACION COIL TORNILLOS SIDE SCREWS FIJACION FIXING THE CARCASA EXTERNAL COVER Condenser cleaning.- During the normal operation the dust and dirtiness will deposit on the coil surface and will obstruct the air flow. Periodically, and depending on the surroundings, the condenser should be cleaned. To do so, remove the external cover of the unit by removing the side screws. Use compressed air blowing from inside or a vacuum cleaner to remove dirtiness on the coil. Alternatively use a brush from the outer face of the coil. Do not force the fins to avoid deformation. Cleaning the evaporator (CV).- Remove any of the side covers of the evaporator block by removing front and side screws. Blow air from outside or brush on the inner side to remove the dirtiness on the coil. SCREWS IN THE COVER SIDE EVAPORATION COIL DRAIN TRAY SCREWS IN THE COVER SIDE 28

intarblock intartop Cleaning the evaporator (CR).- Remove the evaporator cover panel from inside cold room. Deplace the cover to a side to access the coil. Blow or brush to clean it. CONDENSATION COIL GRILLE EVAPORATOR COVER PANEL Drain tray.- To clean the drain tray you can use commercial detergents. In that case, make sure to remove the detergent from the drain bucket inside the condensation block. To do so you can clean the bucket with water. For CR units it is posible to dissasemble the evaporator box to access the condenser coil and the drain tray. To do so, unscrew the box from the condenser and from the lower section. SIDE SCREWS EVAPORATOR BOX EVAPORATOR COIL TRAY Following repair tasks should only be carried out by qualified personnel. Replacement of any electrical part in the unit Any modification of mechanical parts Any operation on the refrigerant circuit Any modification on the protection devices, control panel, control switches. The maintenance tasks shown in this manual do not exclude any maintenance task in regulations and laws. 24. REFRIGERANT LOAD INTARBLOCK units are specifically designed for R404A refrigerant. The use of any other refrigerant in the unit invalidates its guarantee. Any operation related to the load, removal or replacement of refrigerant must always be carried out by qualified personnel and never by the user. Please refer to technical refrigeration manuals for such operations. Units must always be loaded with R404A refrigerant in liquid phase through the HP nipple, in the exact quantity indicated on the data plate. 29

25. DISPOSAL MANAGEMENT After the installation dispose the packaging and pallet in an environmentally friendly manner and according to your regulations. When disposing your unit or any of its parts, do it through an authorised waste management company according to laws and regulations. 26. CONTROL The unit is managed by a electronic board and a control keyboard with the following operating modes: Refrigeration mode The refrigeration operation mode is driven by a thermostatic control according to the room temperature and a temperature target fixed by the user. Thus, when the room temperature is greater than the temperature target, plus a pre-set differential, the compressor starts and stops when the room temperature reaches the target temperature. During the operation mode the display shows the room temperatura. Target temperature can be shown by pressing the key and can be modified by pressing and. To protect the compressor from successive starts, short cycle timing is inbuilt. Fast cooling mode The fast freezing operation mode can be activated or deactivated by pressing the key for 3 seconds. During this operation mode the compressor works continuously for a preset period as configured through the CCt parameter. Defrost mode After every preset period (fixed by the parameter Idf ) the unit executes a defrost cycle. The unit is preset on a defrost mode controlled through the inner coil temperature. In this mode, when the evaporator coil reaches a certain temperature (as predefined value through the parameter dte ), or after certain time (as predefined value through the parameter MdF ). After a defrost cycle the unit stays idle for the drain time (preset time through the parameter Fdt ) to allow the evacuation of all defrosted water. The unit is configured to stop fans during the defrost cycle (parameter FnC ) After the defrost cycle and during the beginning of the normal refrigeration mode, the evaporator fan remains stopped for the time defined by parameter Fnd. Room light Room light can be switched on and off through the key. Keyboard It consists of a display of 3 digits and a 7 key keyboard with LEDs to indicate operation mode and alarms. 30

Fan LED Defrosting LED Fast-cooling mode LED Alarm LED Max. Temperature and fastcooling mode key Min temperature key Target temperatura and validation key intarblock intartop Compressor LED Digital display Defrosting key Cold room Light switch Energy saving mode key Unit On/Off To display and modify target set point; in programming mode it selects a parameter or confirm an operation. By holding it pressed for 3s when max or min temperature is displayed it will be erased. To see the max. stored temperature; in programming mode it browses the parameter codes or increases the displayed value. By holding it pressed for 3s the fast freezing cycle is started. To see the min stored temperature; in programming mode it browses the parameter codes or decreases the displayed value. By holding it pressed for 3s the defrosting is started. Switch ON and OFF the cold room light. Operation LEDs By holding it pressed for 3s Energy Saving function is started or stopped. Switch ON and OFF the auxiliary output. LED Status Description Compresor LED Fan LED Defrosting LED On Flashing On Flashing On Flashing The compressor is running Antyshort cycle safety device on. Pressure switch/es opened (pressure switch). The fan is running Programming (flashing along with Compresor LED) The defrost is enabled Defrost is finished. Drip time in progress Fast-cooling LED On The Fast Freezing cycle is enabled 31

Keyboard functions To switch off the unit.- 1. hold pressed for 5 seconds and the display will show "OFF". To show maximum temperature record.- 1. press 2. the display will show the value together with Hi. 3. press or wait 5 seconds to restore the normal display. To show minimum temperature record.- 1. press 2. the display will show the value together with "Hi". 3. press or wait 5 seconds to restore the normal display. To restart the minimum and maximum temperature record.- 1. while maximum or minimum temperature record is shown, 2. press the key set until the message rst is shown. Do not forget to restart temperature records at the first start-up of the unit. To show and modify target temperature.- 1. press set and the target temperature will be shown 2. the corresponding LED will begin to flash 3. press or to modify its value. 4. to store the new value press set or wait for 10 seconds. To force a manual defrost cycle.- 1. press for 2 seconds. To access Pr1 parameter list, user parameters.- 1. press set and simultaneously for some few seconds, 2. fan and compressor leds will flash, 3. the display will show the first parameter. To access Pr2 parameter list, installer parameters.- 1. access Pr1 list, 2. select parameter Pr2 and press set, 3. the display will show the message PAS followed by 0 - -. 4. press and to modify the flasshing digit and confirm its value by pressing set, to enter the password 321. To modify a parameter.- 1. enter the parameter list, 2. select the parameter by pressing or and press set to visualise its value. 32

3. press or to modify its value. 4. press set to confirm then ew value and jump to the next parameter. 5. to exit the programming mode press set and or wait for 15 seconds. To lock the keyboard.- 1. press and for 3 s. intarblock intartop 2. the message POF will be shown and only the set point and temperature records can be consulted. 3. To unblock the keyboard press and for 3 s. 27. PARAMETER LIST Code Description Range Default List REGULATION SET Set Point. LS US 0 ºC -20 ºC Hy Set Point differential. 0,1 25,5 ºC 2,0 ºC Pr1 LS Minimum set point -50,0 ºC SET MT BT -5 ºC -25 ºC Pr2 US Maximum set point. SET 110,0 ºC 10 ºC -15 ºC Pr2 Od S Time in which functions excluding light are not allowed from starting-up. 0 255 min 1 min Pr2 AC Antishort cycle delay 0 30 min 2 min Pr1 CCt Fast freezing mode time (minutes) 0 23 h 50 min Con Time interval during which the compressor is working after probe default CO F DISPLAY Time interval during which the compressor is stopped due to probe default 0h 30 min 2h 30 min Pr2 0 255 min 15 min Pr2 0 255 min 15 min Pr2 CF Temperature measurement unit. ºC - ºF ºC Pr2 res Resolution integer/decimal point (only if CF = ºC): in (integer) = 1 ºC ; de (decimal) = 0,1 ºC. in - de de Pr1 Lod PARÁMETER NOT AVAILABLE FOR THIS MODEL P1, P2, P3, 1r2 P1 Pr2 red Remote display: P1=room probe ; P2=evap. probe ; P3=ambient probe ; 1r2=P1- P2. DEFROSTING tdf Defrost type. (DO NOT MODIFY). re=electrical heater ; rt=off time ; in=hot gas injection P1, P2, P3, 1r2 P1 Pr2 re, rt, in in Pr1 EdF Defrosting mode: in=standar ; Sd=SmartDefrost in - Sd in Pr2 SdF set point for Smart Defrost. -30,0 30,0 ºC dte Defrosting finalization temperature. -50,0 110,0 ºC 0,0 ºC Pr2 20,0 ºC Pr1 33

Code Description Range Default List IdF Interval between defrosting cycles. 1 120 h 3 h Pr1 Md F dfd Maximum defrosting legth. Display during defrost: rt=real temperature ; it=last recorded temperature ; Set=set point ; def= def message ; deg= deg message. MT BT 0 255 min 15 min Pr1 rt, it,set, def, deg dad Delay after defrosting to display cold room temperature 0 255 min 15 min Pr2 dsd Defrosting start delay. 0 99 min 0 min Pr2 Fdt Time defrosting end to compressor starting-up (draining time). 0 60 min 2 min 3 min Pr2 dp Displayed if defrosting after starting-up. n - y n Pr2 O daf Defrost delay after fast freezing. 0 23 h 50 min FANS FnC Fans operating mode: With compressor (C) / always on (O) / during defrosting (y=yes / n=no). C-n, C-y, O-n, O-y it Pr2 2,0 h Pr2 Fnd Fans operation delay after defrosting. 0 255 min 3 min 4 min Pr2 FSt Fans stop temperature. -50,0 110,0 ºC ALARMS ALC Temperature alarm configuration (ALU and ALL): re=relative ; Ab=absolute. C-n Pr2 10 ºC 0 ºC Pr2 re - Ab re Pr2 ALU Maximum temperature alarm re: -50,0 110,0 ºC Ab: 0,0 50,0 ºC 5,0 ºC Pr1 ALL Minimum temperature alarm re: -50,0 110,0 ºC 5,0 ºC Pr1 Ab: 0,0 50,0 ºC AFH Temperature alarm and fan differential 0,1 25,5 ºC 2,0 ºC Pr2 ALd Temperature alarm delay. 0 255 min 0 min Pr2 dao Delay of temperature alarm after starting up. 0 23 h 50 min 3 h 4 h Pr2 EdA Alarm delay at the end of the defrosting 0 255 min 30 min Pr2 dot Delay of temperature alarm after closing the door 0 255 min 30 min Pr2 doa Delay of opened door alarm 0 255 min 15 min Pr2 rrd outputs restart after doa alarm n - y y Pr2 AL2 Condenser low temperature alarm -50,0 Au2 ºC -40 ºC Pr2 Au2 Condenser high temperature alarm AL2 110,0 ºC 52 ºC Pr2 ALH Differential of condenser low temperature alarm (AL2). 0,1 25,5 ºC 5 ºC Pr2 AtH Differential of condenser high temperature alarm (Au2). 0,1 25,5 ºC 3 ºC Pr2 Ad2 Condenser temperature alarm delay 0 255 min 0 Pr2 da2 Condenser temperature alarm eclusion at starting up 0 23h 50 min 0 Pr2 tba Alarm signal silencing by pressing a key. n - y y Pr2 34