Submittal Transmittal, Consultant

Submittal Transmittal, Consultant (D) Grouped by Each Number Due Date: Boeing 4-20 VPAL - VPAL Construction Project # 4212054-007 Tel: Fax: Skanska USA Building Inc. Date: 2/21/2014 Reference Number: 0086 Transmitted To: Dave Ginestra Transmitted By: Chris Heinle Dutton Electric Company Inc. Skanska USA Building Inc. 12407 Mukilteo Speedway Suite A170 Lynnwood, WA 98087-1518 Tel: (425) 347-7600 Fax: (425) 355-1610 221 Yale Ave. N., Suite 400 Seattle, WA 98109 Tel: 206-726-8000 Fax: 206-328-9235 Submittal Package No Description Due Date 0053-283100 - 0 Electrical - Fire Alarm Transmitted For Delivered Via Tracking Number Construction Email Items Qty Spec SectioSub Section Description Type ID 0001 1 283100 1.5.B Fire Alarm and Detection - PDS Product Data 0002 1 283100 1.5.D Fire Alarm and Detection - Shop SD Drawings Notes Cc: Company Name Contact Name Copies Notes Remarks Signature Signed Date

Submittal Transmittal, Consultant (D) Grouped by Each Number Due Date: 2/21/2014 Boeing 4-20 VPAL - VPAL Construction Project # 4212054-007 Tel: Fax: Skanska USA Building Inc. Date: 2/7/2014 Reference Number: 0079 Transmitted To: Gene Coltran Transmitted By: Chris Heinle The Boeing Company Skanska USA Building Inc. PO BOX 3707 MC 92-58 SEATTLE, WA 98124-2207 221 Yale Ave. N., Suite 400 Seattle, WA 98109 Tel: 206-726-8000 Fax: 206-328-9235 Submittal Package No Description Due Date 0053-283100 - 0 Electrical - Fire Alarm 2/21/2014 Transmitted For Delivered Via Tracking Number Approval Email Items Qty Spec SectioSub Section Description Type ID 0001 1 283100 1.5.B Fire Alarm and Detection - PDS Product Data 0002 1 283100 1.5.D Fire Alarm and Detection - Shop SD Drawings Notes Reviewed As Noted Cc: Company Name Contact Name Copies Notes Remarks This submittal has been reviewed by the Electrical Engineer of Record and marked 'No Exceptions Taken'. This submittal has been reviewed by the Architect of Record and marked 'Reviewed Corrections Noted'. Reference comments on sheet FA-00. This submittal review has concurrence from Boeing Engineering, Dave Honarkhah, George Wagersky, 2/18/2014 and Boeing Fire Protection Engineering, Robert Eaker, 2/20/2014 REVIEWED REJECTED REVIEWED AS NOTED REVISE/RESUBMIT Comments made on shop drawings or submittals during this review do not relieve contractor from compliance with requirements of drawings and specifications. This review is only a check for general conformance with design concept of project and general compliance with information given within the contract documents. This review does not constitute approval or acceptance of deviations from contract documents. Any deviations must be requested in writing in accordance with the contract documents. The contractor is responsible for confirming and correlating quantities and dimensions; selecting fabrication processes and the techniques of construction; coordinating work with all other trades; and performing work in a safe and satisfactory manner. John N. Barton Date; 2/18/2014 THE MILLER HULL PARTNERSHIP, LLP X No exception taken Rejected Make corrections noted See Attached Letter Revise & Resubmit Check is only for general conformance with the design concept of the project and general compliance with the information given in the contract documents. Any action shown is subject to the requirements of the plans and specifications. Contractor is responsible for; dimensions which shall be confirmed and correlated at the job site; fabrication processes and techniques of construction; coordination of his work with that of all other trades and the satisfactory performance of his work. COFFMAN ENGINEERS Date 02/13/2014 By R. Ramos Signature Signed Date

Fire Alarm Submittal For: BOEING 04-20 V-PAL Logan Ave., Renton, WA 98055 System Type: Siemens XLS Siemens Project #: 44OP-142436 Siemen Building Technologies FIS Division 22010 SE 51 st Street Issaquah, WA 98029 Ph (425) 507-4300 Fax (425) 507-4350

Submittal Index BOEING 04-20 V-PAL Fire Alarm System Siemens Job Number: 44OP-142436 November 15, 2013 Qty Cat# Manuf. Model Description 1 6300 SIEMENS XLS Intelligent Fire Alarm Control Panel 1 6326 SIEMENS SSD-C-REM REMOTE LCD DISPLAY W CONTROL 1 6327 SIEMENS CAB-2 & CAB-BATT XLS CABINET & BATTERY BOX ENCLOSURE 1 6103 SIEMENS HFP-11 FIREPRINT DETECTOR 21 6304 SIEMENS HTRI-D DUAL INPUT MONITOR MODULE 1 6304 SIEMENS HTRI-S SINGLE INPUT MONITOR MODULE 9 6304 SIEMENS HTRI-R SINGLE INPUT W/RELAY MODULE 1 6306 SIEMENS HMS-D MANUAL STATION -DUAL ACTION 1 6185 SIEMENS AD2-P AD2-P DUCT HOUSING FOR USE WITH HFP-11 SMOKE DETECTOR 1 6307 SIEMENS RL-HC DUCT DETECTOR REMOTE LAMP 1 of 1

s FireFinder XLS Advanced Fire Alarm Control Panel Standard / 2500-point-capacity addressable fire-alarm control panel (FACP) Ability to network with other FireFinder XLS systems Powerful, easy-to-use programming capabilities Fully field programmable, via Windows laptop PC 6", backlit LCD display User-friendly system interface Touch screen for maintenance operations and function keys Global annunciation and control capability Multi-language display Universal AC power input: 120VAC 240VAC @ 50 / 60Hz 12 amps of system power (expandable to 48 amps) Numerous Relays: Alarm, Trouble, Programmable, etc. SureWire TM addressable-loop technology Polarity-insensitive detection circuits (patented) Useful diagnostic LEDs on all cards Supports FirePrint TM application-specific detection Intelligent / analog detection circuits: Class A or Class B Supports single-person Walk Test Seismic certified System Overview FireFinder XLS is a microprocessor-based, advanced life-safety system that has a 6" display and large, lighted buttons; making it a highly intuitive fire-alarm user interface. Through the use of the unique multiprocessor Network design along with the ability to utilize analog and conventional detection devices FireFinder XLS exemplifies a flexible and highly configurable life-safety system. FireFinder XLS is ideally suited for commercial, institutional and industrial fire detection and notification applications. This FACP complies with the requirements of NFPA Standard 72, and is listed by Underwriters Laboratories under their UL 864 standard. ARCHITECT AND ENGINEER SPECIFICATIONS Modular assembly Supervised remote printer 32-character custom messages Thermal strip printer Security-device monitoring ( UL 1076 Listed) Sprinkler Supervision Degrade-mode operation Coded outputs NCCG Graphics support UUKL Listed for smoke control UL 864 9 th Edition Listed & ULC Listed; FM, CSFM & NYC Fire Dept. Approved Data Sheet Fire Safety & Security Products User help screens Multiple command stations Menu-driven operator commands 5000-event, history-logging capability with on-line and off-line reports Multiple levels of password protection Automatic environmental compensation for smoke detectors Alarm verification by device or zone Pre-alarm operation Logic-controlled output functions Time-based-controlled output functions Holiday schedule City tie / leased line 200 notification-appliance-circuits (NACs) capacity Up to 3.0 amps (24VDC) per NAC Built-in strobe synchronization protocol Supports pre-action, deluge and agent releasing Voice evacuation system (optional) NEC 760 power-limited circuits ( UL 864 Compliant) Intelligent interface to building / process management systems Operates as interactive peer with other XLS or XLSV units in a XNET network Distributed processing Detector Sensitivity Readout / Printout per NFPA 72 Underwriter's Laboratories of Canada also lists this FACP for fire applications under ULC-S527. FireFinder XLS is Factory Mutual Approved; as well as CSFM and NYC Fire Department Approved for use in those specific locales. In addition to the standard fire applications, FireFinder XLS is UL Listed under the category UUKL for smoke control. FireFinder XLS can be used as a listed Fireman's Smoke Control Station in high-rise office buildings, malls and other large structures. FireFinder XLS is UL Listed and FM Approved for Sinorix TM clean-agent systems and pre-action or deluge sprinkler systems, which include foam or water applications. FireFinder XLS operates on the releasing requirements specified in NFPA 13 and 2001. FireFinder XLS Overview 6300

System Overview (continued) The FireFinder XLS system has been seismic qualified in accordance with: International Building Code, 2006 Edition California Building Code, 2007 Edition ASCE Standard 7, 2005 Edition OSHPD CAN 2-1708A.5, Rev. 3 ICC-ES AC 156, Effective 1/1/2007 FireFinder XLS is also OSHPD preapproved under: OSP-0057-10. FireFinder XLS Components A basic FireFinder XLS FACP consists of the following sub-assemblies: Person Machine Interface (Model PMI); Power Supply (Model PSC-12); Device Loop Card (Model DLC); Zone Indicating Card (Model ZIC-4A); Card cage (Model CC-5); Inner Door Blank Single Plate (Model ID-SP); CAB-1, CAB-2 or CAB-3 enclosures. Optional modules that can be installed with this FACP include: Card Cage (Model CC-2); Network Interface Card (Model NIC-C); Zone Indicating Card 8 circuits (Models ZIC-8B / ZIC-2C); Control Relay Card (Model CRC-6); Output Control Module (Model OCM-16); Switch Control Module (Model SCM-8); LED Control Module (Model LCM-8); Fan Control Module (Model FCM-6); Supervised Input Module (Model SIM-16); Power Supply Extender (Model PSX-12); Remote Network Interface (Model RNI); Remote Printer Module (Model RPM); System Status Display (Model SSD); Multi-Point Digital Alarm Communicator (Model MDACT); Two-Module Remote Enclosure (Model REMBOX2); Four-Module Remote Enclosure (Model REMBOX4). The XLS FACP is compatible with a full line of intelligent initiating devices, highlighted by the FirePrint applicationspecified detectors: Models HFP-11 and HFPT-11. XLS is also compatible with the NCC series of graphics command centers. Model PMI contains the site-specific program configuration created in the Zeus system software-programming tool. The controller in Model PMI provides all system logic and supervision. Model PMI contains a large, 6" (1/4 VGA) monochrome LCD display, touch screen and LEDs for displaying system status. A sound is made when there is any unacknowledged event from Model PMI. The display is surrounded by keys that are used to control the displayed information and to navigate through these screens. Keys are also provided to obtain and enter "Help" into the menu features of Model PMI. The FireFinder XLS system is controlled and operated from Model PMI. The intuitive Person Machine Interface uses large, lighted buttons to prompt users as to the next correct system operation that is available (Acknowledge, Silence, Unsilence, Audible or Reset). DLC Device Loop Card DLC Device Loop Card The Device Loop Card (Model DLC) is the interface for connection with FireFinder XLS detectors and initiating devices including manual stations, control and input devices. Model DLC plugs into one (1) slot of the CC-2 or CC- 5 card cage. Programming Model DLC is accomplished using the FireFinder XLS Zeus system softwareprogramming tool. Moreover, Model DLC takes one (1) address on the network, and communicates with two (2) device circuits for a total of 252 detectors and devices. Model DLC has 12 LEDs for diagnostic purposes, and provides ground-fault detection and zone-isolation circuitry. PMI Person Machine Interface PMI Person Machine Interface The Person Machine Interface (Model PMI) is the core of the FireFinder XLS system. Model PMI serves as both operator interface and central microprocessor for the FireFinder XLS system. From Model PMI, the end user can acknowledge events, control the systemnotification appliance circuits and reset the system. Detailed information about the nature and location of the events can also be displayed. ZIC-4A Zone Indicating Card ZIC-4A Zone Indicating Card The Zone Indicating Card (Model ZIC-4A) provides four (4) fully supervised, programmable output circuits for use on each FireFinder XLS. Model ZIC-4A supplies four (4) Class B (Style Y) or Class A (Style Z) type output circuits, power limited to 3.0 amps maximum per circuit.

FireFinder XLS Components (cont. d) Each circuit can be independently programmed for use with listed audible or visual notification appliances; listed emergency audio speakers; municipal tie boxes; leased lines, or as releasing circuits. Model ZIC-4A plugs into one (1) slot in the Model CC-5 or Model CC-2 card cage, and has on-board LEDs for system status and troubleshooting. Indication of power, communication, internal operation, and ground-fault conditions are provided, as well as indication of circuit activation or Trouble conditions. When Model NIC-C is used for XNET communications, Model NIC-C provides communication between systems. The maximum of XNET Model NIC-C cards on a single system (single node) is one (1), for a total of 64 XNET Model NIC-C cards on a peer-to-peer networked system. Model NIC-C has diagnostic LEDs that indicate: Card Fail, CAN Fail, HNET Fail, XNET Fail, Ground Fault, Loop A Fail and Loop B Fail. Model NIC-C Card also has LEDs to indicate Power, Style and Active Networks. ZIC-8B / ZIC-2C Zone Indicating Cards ZIC-8B / ZIC-2C The Zone Indicating Card (Model ZIC-8B) provides eight (8) fully supervised, programmable output circuits for use on FireFinder XLS. Model ZIC-8B supplies eight (8) Class B (Style Y) type output circuits, power limited to 2.0 amps maximum per circuit. Each circuit can be independently programmed for use with listed audible or visual notification appliances, or listed emergency audio speakers. Model ZIC-8B plugs into one (1) slot in the Model CC-5 or Model CC-2 card cage, and has on-board LEDs for system status and troubleshooting. Model ZIC-2C mounts directly on Model ZIC-8B, and allows each of the Model ZIC-8B output circuits to be used for two-channel voice applications. Indication of power, communication, internal operation, and ground-fault conditions are provided, as well as indication of circuit activation or Trouble conditions. HLIM Line Isolator Module HLIM Line Isolator Module The loop-isolator module (Model HLIM) provides shortcircuit protection on FireFinder XLS intelligent device circuits (see: Model DLC). When Model HLIM detects a short circuit, Model HLIM is able to isolate the affected segment of the circuit allowing the remaining devices to continue operation. Model HLIM is self-restoring automatically reconnecting to circuit segment when the fault is removed. Model HLIM can be wired in either a Style 4 or Style 6 configuration. Model HLIM does not occupy a device address on the Model DLC circuit, and does not require programming. Up to 15 Model HLIM modules may be installed on each Model DLC loop. HCP Control Point Module NIC-C Network Interface Card NIC-C Network Interface Card The Network Interface Card (Model NIC-C) provides HNET or XNET network communications between enclosures. In addition to the HNET or XNET communication, Model NIC-C provides CAN network communication within an enclosure or external to the enclosure. HNET or XNET communication can be wired Style 4 or Style 7, but the CAN network can be wired Style 4 only. When used for HNET communications, Model NIC-C provides communication between enclosures on a single system. HCP Control Point Module Model HCP provides an intelligent control point for the FireFinder XLS. Model HCP can be programmed as an independent, remotely located telephone zone, speaker zone or notification appliance circuit. Model HCP is designed to be used with the Siemens Fire Safety Alarm Signaling Devices product line. Model HCP communicates through the Model DLC analog loop, and can be wired either Class A (Style Z) or Class B (Style Y). The 24 VDC power input comes from either the control panel or from any UL Listed power-limited, auxiliary-power supply.

FireFinder XLS Components (cont. d) CRC-6 Controllable Relay Card CRC-6 Controllable Relay Card The Controllable Relay Card (Model CRC-6) is used with the FireFinder XLS FACP. Model CRC-6 is designed to provide auxiliary control of building functions, such as: door-holder release, elevator capture, smoke control, lock release, etc. Model CRC-6 plugs into one (1) slot in the Model CC-5 or Model CC-2 card cage. Model CRC-6 provides six (6), fully programmable relays. Each relay contains one (1) set of SPDT contacts rated at 4 Amps 30 VDC / 120VAC resistive and 3.5 amps 120VAC inductive (0.6 P.F.) SIM-16 Supervised Input Module SIM-16 Supervised Input Module The Supervised input Module (Model SIM-16) is a remotely located, general-purpose input module. Model SIM-16 provides 16 input circuits for remote system monitoring. Each input can be individually programmed as supervised (dry-contact only) or unsupervised (generalpurpose input.) Model SIM-16 has two (2) Form C relays. The relays and inputs are programmed using the Zeus system software-programming tool. CC-2 Card Cage-2 Slots CC-5 Card Cage-5 Slots CC-5 / CC-2 Card Cages The Models CC-5 / CC-2 card cages provide the physical mounting location and all wiring connection points for all fire-and-voice system options cards for the FireFinder XLS system. Model CC-5 has five (5) slots, while Model CC-2 has two (2) slots. All cards plugged into the CC-5 / CC-2 card cage communicate with other FireFinder XLS modules via a common data bus. Connectors are provided on the left and right side of the CC-5 to connect a 60-pin cable for communications with the FireFinder XLS operator interface, power supplies and amplifiers modules. Field wiring to devices and circuits terminates on the Models CC-5 / CC-2 card cages. All cards designed for use with the Models CC-5 / CC-2 route their field wiring terminations to the top of the Model CC-5 / CC-2 card cages. These connections are all power limited. Internal wiring connections distribute 24VDC to cards or high-level audio signals (depending on application used) connect to the bottom of the Model CC-5 / CC-2 card cages. These connections are all non-power limited. All wiring connections to the Model CC-5 / CC-2 card cages are to removable terminal blocks. Terminal blocks are rated for use with wire sized 12 American Wire Gauge (AWG) to 24AWG. Each connector is numbered to make wiring terminations to the correct position on the terminal block simple in order to reduce potential wiring errors. CDC-4 Conventional Detector Card CDC-4 Conventional Detector Card The Conventional Detector Card (Model CDC-4) is used to monitor Siemens Fire Safety conventional detectors on the FireFinder XLS system. Model CDC-4 can be used in applications where conventional detectors are more suited than addressable detectors, such as hallways or large meeting rooms. Also, Model CDC-4 can be used to upgrade Siemens conventional fire-alarm panels to the FireFinder XLS system without requiring detector replacement. SCM-8 Switch Control Module SCM-8 Switch Control Module The Switch Control Module (Model SCM-8) is a FireFinder XLS-option module that provides manual control to the Emergency Voice Evacuation System (EVAC) or manual fire-system control. Each Model SCM-8 module provides eight (8) momentary push-button switches and 16 light-emitting diodes (LEDs) to indicate their status. Each switch is assigned two (2) LEDs, as well as a label to indicate the switch's programmed usage. The label slides behind a clear protective membrane. One of the LEDs assigned to each switch is a dual-colored LED, which is used to indicate what type of signal is active.

FireFinder XLS Components (cont. d) Each Model SCM-8 switch is fully programmable, and may be used to control speaker circuits and a wide range of general-system functions such as: All Call, All Evac, Warden's Page, Speaker, etc. Any number of circuits may be grouped and controlled by a single switch. Switch usages and zone groupings are assigned using the Zeus system software-programming software. Model SCM-8 modules are mounted on a hinged panel, as a part of the FireFinder XLS Command Console enclosure. PSC-12 Power Supply Charger Module The Power Supply Charger Module (Model PSC-12) is a high-current power supply that provides the FireFinder XLS primary-regulated 24VDC power to operate. Model PSC-12 is rated at 12Amps (Alarm) / 5Amps (Standby), and has a built-in battery charger, capable of charging up to 100 AH batteries. Model PSC-12 is an addressable-intelligent, microprocessor-controlled module that communicates its status to the system-operator interface (PMI). Model PMI is able to query the status of the power supply to obtain information regarding system-charging current, terminalloading information, ground-fault conditions and more. LCM-8 LED Control Module LCM-8 LED Control Module The LED Control Module (Model LCM-8) is a FireFinder XLS-option module that provides LED annunciation for FireFinder XLS system activity. Each Model LCM-8 contains eight (8) groups of two (2) LEDs each of which can be assigned to desired outputs using the Zeus system software-programming tool. Eight (8) LEDs are dual-color capable (Red or Green / flashing or steady). The remaining LEDs are Amber flashing or steady. A space is provided for labeling of LED functions. The label slides behind a clear, protective membrane. Model LCM-8 dimensions are identical to Model SCM-8, and Model LCM-8 is mounted on the same hinged panel, as a part of the FireFinder XLS Command Console enclosure. FCM-6 Fan, Motor, Dampers Control Module FCM-6 Fan, Motor, Dampers Control Module The Fan, Motor, Dampers Control Module (Model FCM-6) is a FireFinder XLS command-console option module that provides manual control of building HVAC system fans, motors, and dampers. Each Model FCM-6 module provides six (6) sets of three (3) push-button switches for manualsystem control. Each switch has three (3), associated LEDs to indicate Fan / Damper / Motor status: OFF (Red LED), ON (Green LED), TROUBLE (Yellow LED). PTB Power Termination Board PTB Power Termination Board Model PSC-12 comes packaged with a module called the Power Termination Board (Model PTB). Model PTB is required for operation with Model PSC-12. Model PTB filters the power from the incoming AC mains, and distributes it to the Model PSC-12 power supply and the optional Model PSX-12 power-supply extender. Model PTB has an optional connector that can be used during system installation, commissioning and service to provide the technician with a place to plug in their laptop PC, if required. Model AC-ADPT is an optional accessory cable that allows connection on one side to Model PTB, via a keyed connector and on the other end directly into to the laptop's transformer. Most laptop-computer external power transformers have removable AC power cords, which can be replaced by the optional Model AC-ADPT to temporarily provide an AC power source for laptop-pc usage during system installation, service and maintenance calls when needed. PSX-12 Power Supply Extender PSC-12 Power Supply Charger Module PSX-12 Power Supply Extender The Power Supply Extender (Model PSX-12) is a high-current, auxiliary power supply that expands the main Model PSC-12 power supply and battery charger of the FireFinder XLS system with an additional 24VDC power. Model PSX-12 is rated at 12 Amps.

FireFinder XLS Components (cont. d) RNI Remote Network Interface RNI Remote Network Interface The Remote Network Interface (Model RNI) provides a connection point for use with equipment mounted in a remote-lobby enclosure on the FireFinder XLS FACP. Model RNI is used to provide additional input, output and control features to the system remotely, via the main FACP. These additional features may include control switches and indicators: (Models SCM-8, LCM-8 and FCM-6), remoteemergency paging microphones or telephones: (Models LVM, FMT), or controls used in graphic annunciators (Models SIM16, OCM-16) or system-status display with the ability to acknowledge alarms, silence audibles and reset the system (Model SSD-C-REM). Model RNI allows Model PMI to be mounted in the Model REMBOX2 or Model REMBOX4 remote lobby enclosure. RPM Remote Printer Module RPM Remote Printer Module The Remote Printer Module (Model RPM) provides a means of connecting the FireFinder XLS system to a printer, such as Model PAL-1, for creating a hard copy of system status and configuration reports. Simultaneously, Model RPM provides an output port that can be configured to communicate with external systems. Models SSD-C and SSD-C-INT have an integral keyswitch that enables these control buttons to operate. Model SSD-C-REM is located within a locked cabinet. Hence, no additional keyswitch is required for enabling the control buttons. CAB1 Single Row Enclosure CAB1 Single Row Enclosure Model CAB 1, the smallest of the FireFinder XLS enclosures, can house a single Model CAB-MP cabinet mounting plate for mounting card cages, power supplies and bulk amplifiers. Model CAB1 also has four (4) mounting slots on the inner door for mounting Model PMI and Model ID-MP switch module brackets. Model CAB1 comes complete with a black back box; black inner and outer doors; a single lock and key set on the outer door; a single, installed cabinet mounting plate (Model CAB-MP), and a single, installed outer door lens plate (Model OD-LP). A red version (Model CAB1-R) is also available approximate size: 27" (68.6cm.) high, 26" (66cm.) wide, and 8" (20.3cm.) deep. System-Status Display SSD-Series System-Status Display The System Status Display (SSD-series model displays) is a remote LED / LCD display that shows the local status of a FireFinder XLS system. An LED illuminates when Alarm, Supervisory, Trouble, and Security events occur on the system. A (4) four-line liquid-crystal display (LCD) will give details of the event in alphanumeric form. The display can be toggled to display additional events. Optional remote system control capabilities are available. Models SSD-C, SSD-C-INT, and Model SSD-C-REM have three (3) additional control buttons to acknowledge events, silence audible circuits, and reset the system. MDACT Multi-Point Digital Alarm Communicator Transmitter MDACT - Multi-Point Digital Alarm Communicator Transmitter The Multi-Point Digital Alarm Communicator Transmitter (Model MDACT) is used in FireFinder XLS systems where point identification of Alarm, Supervisory, Security and Trouble events is required at Central or Remote Receiving Stations. An intelligent RS 485 communications protocol transmits all system information to Model MDACT. The installer selects the specific event or groups of events that are set to transmit from Model MDACT over phone lines to listed receiving station equipment. In turn, Model MDACT can transmit point information, via the Ademco Contact ID and the SIA protocol. A Mounting Plate (Model MOM2-XMP), MOM-2 card cage, and an XMI Interface Card are required for installation.

FireFinder XLS Components (cont. d) TSP-40A Thermal Strip Printer TSP-40A Thermal Strip Printer The Thermal Strip Printer (Model TSP-40A) is designed for use with the FireFinder XLS system. Model TSP-40A acts as an event-logging device, providing a permanent history report of all system activity. Model TSP-40A mounts in the FireFinder XLS Model CAB 1, Model CAB2 or Model CAB3 enclosure, and its printout is visible through a window in the locked-door enclosure. Printouts are automatically spooled onto a take-up reel for tidy, uniformed records storage. CAB2 Two-Row Enclosure CAB2 Two-Row Enclosure The Two-Row Enclosure (Model CAB2) is the mid-sized FireFinder XLS enclosure capable of housing up to two (2) Model CAB-MP cabinet mounting plates. The inner door has two (2) rows of four (4) mounting slots. The outer door has space for mounting two (2) outer door plates (Models OD-LP, OD-BP or OD-GP). The outer door can be configured to open from either side. Model CAB2 consists of the Model CAB2-BB back box, the Model CAB2- BD black inner and outer door package, and one (1) Model OD-LP lens plate. The outer door has a single lock and key set installed. A red version (Model CAB2R) is also available. Approximate size is 45 (114.3cm.) high, 26 (66cm.) wide, and 8 (20.3cm.) deep. The outer door can be configured to open from either side. Model CAB3 consists of the Model CAB3-BB back box, the Model CAB3-BD black inner and outer door package, and one (1) Model OD-LP lens plate. The outer door has two (2) locks and key sets installed. A red version (Model CAB3R) is also available. Approximate size is 63" (160cm.) high, 26" (66.4cm.) wide, and 8" (20.3cm.) deep. Enclosure Trim Kits Trim kits are available for all system enclosures for semiflush mounting applications. Model CAB1-TK (for black enclosures) and the Model CAB1R-TK (for red enclosures) fit inside the Models CAB1 and CAB1-R enclosures. Similarly, Models CAB2-TK and CAB-2R-TK fit inside the Model CAB-2 enclosure, while Models CAB3-TK and CAB3R- TK fit the Model CAB-3 enclosure. Remote Transponders The FireFinder XLS system can use remote transponders for mounting additional modules such as amplifiers without requiring Model PMI or any control switches. Special doors are available for systems using Model CAB-2 or Model CAB-3 remote transponders. These doors (Models CAB2-XBD and CAB3-XBD) omit the unused inner door, and come complete with ventilation louvers built into the door. Model CAB2-XBD fits into Model CAB2-BB, and Model CAB3-XBD fits into Model CAB3-BB. Model CAB2-XBD and CAB3-XBD are supplied in black. Red versions (Models CAB2-XRD and CAB3-XRD) are also available. Complete box and door kits are available, Models CAB2-X and CAB3-X. CAB-MP Cabinet Mounting Plate CAB-MP Cabinet Mounting Plate The Model CAB-MP cabinet mounting plate provides mounting for a single row of modules in a FireFinder XLS cabinet. Four (4) module spaces are available on Model CAB-MP, which is used to mount the Model CC-5 card cage; the Model CC-2 card cage; the Model PSC-12 power supply; the Model PSX-12 power-supply extender, and the Model ZAM-80 / 180-zone amplifiers. CAB3 Three-Row Enclosure CAB3 Three-Row Enclosure Model CAB3, the single largest FireFinder XLS enclosure available, can house a maximum three (3) Model CAB- MP cabinet mounting plates in the enclosure, and three (3) rows of inner-door mounting slots. ID-MP Inner Door Mounting Plate

FireFinder XLS Components (cont. d) ID-MP Inner Door Mounting Plate The inner door mounting plate (Model ID-MP) is mounted on the inner door of any given model CAB enclosure. Model ID-MP plates are used to mount switch-control modules (Model SCM-8); LED control modules (Model LCM-8), or fan-control modules (Model FCM-6). Four (4) mounting plates are included in each Model ID- MP. Each mounting plate has four (4) spaces for control modules, and can hold either four (4) Model SCM-8 modules (one [1] control module space for each module); four (4) LCM-8 (one [1]control module space for each module), or two (2) Model FCM-6 modules (two [2] module spaces for each module). Combinations are also allowed. Blank spaces in Model ID- MP can be covered using the blank-control-module plate (Model BCM). Up to four (4) Model ID-MP modules can be mounted in a single row on the inner door. OD-LP Outer Door Lens Plate OD-LP Outer Door Lens Plate The Outer Door Lens Plate (Model OD-LP) is a clear plastic lens plate mounted on the outer door of a system cabinet. Model OD-LP is used to allow operators to see the system interface and controls mounted on the inner door, but restricts access to unauthorized users. Moreover, the plate covers an entire row on the outer door. A single lens plate is included with each Model OD-LP. ID-SP Inner Door Blank Single Plate ID-SP Inner Door, Blank Single Plate The inner door, blank single plate (Model ID-SP) is used to cover any single-module blank spaces on the inner door not used to mount Model PMI or Model ID-MP. Up to four (4) Model ID-SP modules can be mounted in a single row on the inner door. Two (2) blank plates are included in each Model ID-SP. ID-FP Inner Door Full-Blank Plate Model ID-FP is a blank plate that covers the full opening of the row on an inner door, and is used for applications requiring full, dead-front protection. A single, full blank plate is included in Model ID-FP. BCM Blank Control Module Plate BCM Blank Control-Module Plate Model BCM plates can be mounted on a single ID-MP. Four (4) blank module plates are included in each Model BCM. OD-BP Outer Door Blank Plate OD-BP Outer Door Blank Plate The Outer Door Blank Plate (Model OD-BP) is used to cover an entire row on the outer door of a system cabinet. Model OD-BP is used when there is no Model PMI or control modules mounted on the adjacent row of the inner door. One (1) blank plate is included in each Model OD-BP. OD-GP Outer Door Grill Plate OD-GP Outer Door Grill Plate The Outer Door Grill Plate (Model OD-GP) also covers an entire row on the outer door of a system cabinet, but has four (4) rows of ventilation louvers on it. Model OD-GP is mounted in front of system bulk amplifiers, card amplifiers, or other modules that generate heat. Using Model OD-GP will permit airflow across these modules to aid in heat dissipation. One (1) grill plate is included with each Model OG-GP. Remote System Enclosures Models REMBOX2 and REMBOX4 are FireFinder XLS system enclosures that are used for remotely mounting inner-door modules, such as: Model PMI; switch modules (Model SCM series); Live Voice Modules (Model LVM), and Firefighters Master Telephone (Model FMT) modules. Models REMBOX2 and REMBOX4 are thinner than regular Model CAB-series of enclosures just 5" (12.7cm.) deep overall, and are perfect for mounting in limited-space areas (e.g. office-complex lobbies or behind a receptionist's desk).

FireFinder XLS Components (cont. d) No card cages, power supplies or bulk amplifiers can be mounted in a given Model REMBOX-series enclosure due to their smaller depth. However, Model PMI and some modules (e.g. the remote network interface module [Model RNI]; the output control module [Model OCM-16], and the supervised input module [Model SIM- 16]) can be mounted in a given Model REMBOX-series enclosure. Due to the depth of Models LVM and FMT, no Model OCM-16 or Model SIM-16 modules can be used simultaneously with Model LVM or Model FMT. Model REMBOX2 and Model REMBOX4 are designed for flush mounting with no trim kit required. Both enclosures also come with a clear lens plate on the cover. A bracket known as Model REMBOX4-MP can be used to mount up to eight (8) output control modules (Model OCM-16) or supervised input modules (SIM-16). The REMBOX4-MP must be purchased separately. Approximate size of the REMBOX4 is 24" (61cm.) wide, 18-1/2" (47cm.) high and 5" (12.7cm.) deep. NRC Network Ring Card NRC Network Ring Card Model NRC provides XNET, peer-to-peer communication between FireFinder XLS systems. One (1) Model NRC is required for each XLS FACP, in order to allow FireFinder XLS nodes to be wired in a Class A, [Style 7] ring topology. REMBOX2 Two-Module Remote Enclosures REMBOX2 Two Module Remote Enclosures REMBOX2 has two (2) inner-door module spaces, and can hold a single Model PMI, up to two (2) switch module brackets and one (1) Model LVM. Combinations are also allowed. REMBOX2 can also mount a single RNI remote network interface on a bracket included in the backbox. A bracket called the REMBOX2-MP can be used to mount up to four OCM-16 output control modules or SIM-16 supervised input modules. Model REMBOX2-MP must be purchased separately. Approximate size of Model REMBOX2 is 14-1/2" (36.8cm.) wide, 18-1/2" (47cm.) high and 5" (12.7cm.) deep. NCC-G Network Color Graphics NCC-G - Network Color Graphics Model NCC-G is a PC-based, color-graphics command center designed for use with the XNET network, and provides full control and annunciation for a XNET network for a maximum 63 XLS, MXL-IQ or MXL systems. Model NCC-G is used to monitor and control Alarm, Trouble, Security, Supervisory and all system events from an individual (of many) XLS FACPs. Model NCC-G maintains a widespread history log of all system events, as well as extensive report-generation capabilities. User programmable function buttons allow site specific control functions. Multiple NCC-Gs may be connected to XNET network. Each NCC-G ordered separately. REMBOX4 Four-Module Remote Enclosures REMBOX4 Four-Module Remote Enclosures Model REMBOX4 has space for mounting four (4) innerdoor modules. Any combination of Model PMI (twomodule spaces); switch module brackets; Model LVM, or Model FMT (one-module space each) can be used. Unused module spaces can be covered with Model ID-SP blank plates. The REMBOX4 can also mount a single remote network interface (Model RNI) on a bracket included in the backbox. MLC MXL Line Card [for FireFinder XLS]

FireFinder XLS Components (cont. d) MLC - MXL Line Card [for FireFinder XLS] The MXL Line Card (Model MLC) is an optional card for the FireFinder XLS panel that supplies two (2) intelligent analog circuits, utilizing the Model I series; Model ID series; Model IL series or Model FP seriestype intelligent devices. Model MLC occupies two (2) addresses on the HNET network, and devices connected to the Model MLC circuits are dynamically supervised by FireFinder XLS through the use of a unique communications protocol. XLS-MLE6-ADPT Enclosure Adapter XLS-MLE6/R-ADPT XLS MLE-6/R Enclosure Adapter Model XLS-MLE6-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MLE-6 large black enclosures. Model XLS-MLE6R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL MLE-6R large red enclosures. XLS-MSE2-ADPT Enclosure Adapter XLS-MSE2/R-ADPT XLS MSE-2/R Enclosure Adapter Model XLS-MSE2-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MSE-2 small black enclosures. Model XLS-MSE2R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MSE-2R small red enclosures. XLS-MSE3-ADPT Enclosure Adapters XLS-MSE3/R-ADPT XLS MSE-3L/R or MSE-3M/R Enclosure Adapters Model XLS-MSE3-ADPT is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL-IQ Model MSE-3L or Model MSE-3M black enclosure. Model XLS-MSE3R-ADPT is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL-IQ Model MSE-3LR or Model MSE-3MR red enclosure. XLS-MME3-ADPT Enclosure Adapters XLS-MME3/R-ADPT XLS MME-3/R or MBR-2 Enclosure Adapters Model XLS-MME3-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MME-3 or Model MBR-2 medium black enclosures. Model XLS-MME3R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MME-3R medium red enclosures. XLS-RCC1-ADPT Enclosure Adapter XLS-RCC-1-ADPT XLS RCC-1 Enclosure Adapter Model XLS-RCC1-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in older-generation Model RCC-1 surfacemount enclosure. XLS-RCC13F-ADPT Enclosure Adapters

FireFinder XLS Components (cont. d) XLS-RCC13F/R-ADPT XLS RCC-1F/R or RCC-3F/R Enclosure Adapters Model XLS-RCC13F-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in older-generation Model RCC-1F or Model RCC-3F black, flush-mount enclosure. Model XLS-RCC13FR-ADPT is an adapter that allows the Model SSD/-C series to be mounted in older-generation RCC-1FR and RCC-3FR, red flush-mount enclosure. VPM VESDA Interface Equipment C900V2 Dialer-Capture Ethernet Module C900V2 Dialer-Capture Ethernet Module The Dialer-Capture Ethernet Module (Model C900V2) links the data output of Model MDACT from the FireFinder XLS FACP to an Ethernet connection on a local-area network (LAN) or wide-area network (WAN) for communication to a central station over the Internet. Model C900V2 also allows Model MDACT to be optionally linked to the public switched telephone network (PSTN) for communication to a central station over telephone lines. VESDA-HLI-KIT VESDA High-Level Interface Kit VPM-MP VESDA Mounting Plate IIC Interface Isolation Card IIC Interface Isolation Card The Interface Isolation Card (Model IIC) is designed to isolate network signals when used with a Model NCC ring configuration, via Model NRC. Model IIC executes the aforementioned isolation by removing the backplane network signals from each Model CC-2 card cage. Model IIC also provides one (1) end of CAN termination on each side of Model CC-2. VPM, VESDA-HLI-KIT and VMP-MP VESDA Interface Equipment The Very Early Smoke Detection Aspiration (VESDA) Peripheral Module (Model VPM) and the VESDA High- Level Interface Kit (Model VESDAHLI-KIT) are optional FireFinder XLS modules that work in conjunction to provide bi-directional communication between the FireFinder XLS FACP and multiple VESDA detection networks for the following types of VESDA detectors: LaserCOMPACT LaserFOCUS LaserPLUS LaserSCANNER Model VPM allows each FireFinder XLS FACP to annunciate Alert, Action, Fire 1, and Fire 2 levels, as well as provide faults from any zone on a connected VESDA network. The VPM Mounting plate (Model VPM-MP) allows mounting one (1) Model VPM and two (2) of Model VESDAHLI-KIT inside a standard FireFinder XLS Model CAB1, Model CAB2 or Model CAB3 enclosure. Model VPM-MP utilizes two (2) module spaces on a single row of each enclosure. PMI-2 Person Machine Interface 2 PMI-2 Person Machine Interface 2 The Person Machine Interface 2 (Model PMI-2) is the primary user interface for the FireFinder FACP. Model PMI- 2 serves as both operator interface and central microprocessor for each XLS system. From each Model PMI-2, the end-user can Acknowledge events; control the system notification appliance circuits (NACs), and reset the system. Detailed information about the nature and location of the events can also be displayed. Temperature and Humidity Range FireFinder XLS components are UL 864 9 th Edition Listed for indoor dry locations within a temperature range of 120+/-3 F (49+/-2 C) to 32+/-3 F (0+/-2 C) and a relative-humidity range of 93+/-2% at a temperature of 90+/-3 F (32+/-2 C).

Details for Ordering (continued) Model Number Part Number Description 599-050092 PMI and GPMI AC-ADPT 500-633992 Technician laptop power connector BCM 500-033320 Blank control module plate, [four (4) per package] C900V2 S54430-C13-A2 Dialer-Capture Ethernet Module CAB-1 500-633007 Complete single-row cabinet, black CAB-1R 500-633728 Complete single-row cabinet, red CAB1-TK 500-633013 Single-row trim-kit cabinet, black CAB1R-TK 500-633729 Single-row trim-kit cabinet, red CAB2-BB 500-633009 (2) Two-row back box, black CAB2-RB 500-634941 (2) Two-row back box, red CAB2-BD 500-633008 (2) Two-row inner & outer door set, black CAB2-RD 500-633755 (2) Two-row inner & outer door set, red CAB2-TK 500-633014 (2) Two-row trim-kit cabinet, black CAB2R-TK 500-633753 (2) Two-row trim-kit cabinet, red CAB2-XBD 599-633768 CAB2 transponder door CAB2-X 599-034252 Complete CAB2 w/ transponder door [no inner door] CAB2-XRD 500-633792 Medium-enclosure transponder door, red [mounts to CAB2-RB] CAB3-BB 500-633011 (3) Three-row back box, black CAB3-RB 500-634942 (3) Three-row back box, red CAB3-BD 500-633010 (3) Three-row inner & outer door set, black CAB3-RD 500-633757 (3) Three-row inner & outer door set, red CAB3-TK 500-633015 (3) Three-row trim-kit cabinet, black CAB3R-TK 500-633754 (3) Three-row trim-kit cabinet, red CAB3-XBD 599-633769 CAB3 transponder door CAB3-X 599-034253 Complete CAB3 w/ transponder door [no inner door] CAB3-XRD 500-633793 Large-enclosure transponder door, red [mounts to CAB3-RB] CAB-MP 500-633012 Back box module mounting plate CAN Cable CCL 599-634214 3 ft. (91.4 cm.) Length required for: SCM / LCM / FCM modules from Models CC-5 / CC-2 Inner Doors and from Row-to-Row on Model CAB-series Inner Doors CC-2 500-633440 Two (2) slot card cage CC-5 500-633037 Five (5) slot card cage CDC-4 500-034200 Conventional detector card CRC-4 500-033250 Controllable relay card CSB 500-033130 CAN Sounder Board DCT-P 500-699291 MDACT programmer DLC 500-033090 Device loop card FCM-6 500-033140 Fan-control-module switches {ON, OFF, AUTO} GPMI-UK 500-650066 Software-upgrade kit for PMI {to allow global functionality} HCP 500-034860 Intelligent control point HLIM 500-033170 Line-isolator module ID-FP 500-633029 (4) Four module inner-door blank plate ID-MP 500-633027 Inner-door enclosure mounting plate, [four (4) per package] ID-SP 500-633028 Single-module inner-door enclosure mounting plate, [two (2) per package] IIC 500-850328 Interface Isolation card LCM-8 500-033100 LED Annunciator Module [eight (8) LED sets] MDACT 500-699254 Multi-point digital-alarm communication transmitter MLC MXL addressable-device line card S54431-B4-A1 [used for FireFinder XLS] MOM2-XMP Mounting plate for Model MOM-2 500-634822 [used for FireFinder XLS] Details for Ordering (continued) Model Number Part Number Description MOM-2 MXL module card cage 500-892766 [one (1) full slot] NIC-C 500-033240 Network interface card NRC 500-050337 Network ring card OD-BP 500-633017 Outer door blank plate OD-BP-R 500-634919 Outer door blank plate, red OD-GP-R 500-634920 Outer door grill plate, red OD-GP 500-633018 Outer door grill plate OD-LP 500-633016 Outer door lens plate PAL-1 500-692407 UL Listed parallel printer PMI 500-033070 Person Machine Interface PMI-2 S54430-C1-A1 Person Machine Interface 2 PMI-INT 500-034160 Person machine interface [with multi-lingual overlays] PSC-12 500-033340 Power supply with battery charger [12A @ 24VDC] PSX-12 500-034120 Power supply extender [12A @ 24VDC] PTB 500-033390 Power termination board REMBOX2 500-633772 (2) Two-module remote lobby enclosure, black REMBOX2R 500-650612 (2) Two-module remote lobby enclosure, red REMBOX2-MP 500-634211 Mounting plate for Models OCM-16 / SIM-16 in Model REMBOX2 REMBOX4 500-633914 (4) Four-module remote lobby enclosure, black REMBOX4-MP 500-634212 Mounting plate for Models OCM-16 / SIM-16 in Model REMBOX4 REMBOX4R 500-650613 (4) Four-module remote lobby enclosure, red RNI 500-033420 Remote network interface module RPM 500-033270 Remote printer module SCM-8 500-033040 Switch module, eight (8) switches SIM-16 500-034060 Supervised input module SSD 500-034740 System-status display SSD-C 500-648733 System-status display with control SSD-INT System-status display with 500-034740 multi-lingual overlays SSD-C-INT 500-034750 System-status display with control and multi-lingual overlays SSD-C-REM 500-634773 System-status display with control for remote lobby enclosure TSP-40A 500-634933 Thermal-strip printer TSP-XB 500-849949 Brackets for thermal-strip printer TSP-XC 500-849950 Cables for thermal-strip printer VPM S54430-F93-A2 VESDA Peripheral Module VPM-MP S54430-F95-A2 Mounting Plate for VESDA Peripheral Module VESDA-HLI-KIT S54430-F99-A2 VESDA High-Level Interface Kit XLS-MLE6-ADPT S54430-C9-A1 MLE-6 enclosure adapter for XLS, black XLS-MLE6R-ADPT S54430-C9-A2 MLE-6R enclosure adapter for XLS, red XLS-MME3-ADPT MME-3 and MBR-2 enclosure adapters for S54430-C8-A1 FireFinder XLS, black XLS-MME3R-ADPT S54430-C8-A2 MME-3R enclosure adapter for XLS, red XLS-MSE2-ADPT S54430-C7-A1 MSE-2 enclosure adapter for XLS, black XLS-MSE2R-ADPT S54430-C7-A2 MSE-2R enclosure adapter for XLS, red MXL-IQ MSE-3L and MSE-3M enclosure adapters XLS-MSE3-ADPT S54430-C14-A1 for XLS, black XLS-MSE3R-ADPT S54430-C14-A2 MXL-IQ MSE-3LR & MSE-3MR enclosure adapters for XLS, red XLS-RCC1-ADPT S54430-Z14-A1 RCC-1enclosure adapter for XLS-SSD, black XLS-RCC13F-ADPT S54430-Z13-A1 RCC-1F & RCC-3F enclosure adapters, black XLS-RCC13FR-ADPT S54430-Z13-A2 RCC-1FR & RCC-3FR enclosure adapters, red ZIC-2C 500-648671 (2) Two-channel adapter card, via (Model ZIC-8B) ZIC-4A 500-033050 (4) Four-circuit zone indicating card ZIC-8B 500-648670 (8) Eight-circuit zone indicating card Notice: This marketing data sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.usa.siemens.com/fire (SII-FS) Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 June 2013 Supersedes sheet dated 9/12 (Rev. 9)

s FireFinder XLS System-Status Display Series Models SSD, SSD-C and SSD-C-REM Catalog Sheet Fire Safety & Security Products 4 x 40 backlit LCD screen Event and audible status LEDs Scroll buttons to view additional events Local sounder Supports Style 4 or Style 7 wiring Built-in transient protection Mounts in its own enclosure or REMBOX Optional local-system control Downloadable firmware UL 864 9 th Edition Listed and ULC Listed; FM, CSFM & NYMEA Approved Product Overview The System-Status Display (SSD Series) is a remote LED / LCD display that shows the local status of a FireFinder XLS system. A LED will illuminate when Alarm, Supervisory, Trouble and Security events occur on the system. A four-line LCD will give details of the event in alphanumeric form. The display can be toggled to display additional events. Optional remote-system control capabilities are available. Specifications The SSD Series display has separate LEDs for Alarm, Supervisory, Trouble and Security events on the FireFinder XLS system. Each LED will flash when unacknowledged events of that type are present on the system. The LED will change to steady, upon acknowledgment of the event. Also, there are two (2) LEDs that indicate the state of audible circuits on the system: one (1) LED to indicate that the circuits are active and one (1) LED to indicate the circuits have been silenced. The LCD display on the SSD Series display has four (4) rows 40 characters for each row. When the FireFinder XLS system is in its normal supervisory state with no events present, the display will annunciate the system ID information, the date and the time of day. When an event occurs on the system, the LCD display will show the event type and address, the time of the event, the custom message for that address, the usage of the device, and whether the event is acknowledged or not. Additionally, the display will show the total number of all types of events present on the system. The display has a backlight feature that operates upon receiving any event information or when any operator buttons are pressed. A local sounder is included with the SSD Series display that operates when any events are displayed on the system. The sounder can be optionally disabled through software programming. Pressing any operator buttons will silence the local sounder when an event is present. FireFinder XLS 6326

Specifications (continued) The SSD Series display has two (2) display-control buttons that are used to display the next or the previous event information in the sequence, and a local sounder silence button. Programming for the SSD Series display is done with the Zeus programming tool. Models SSD-C and Model SSD-C-REM have three (3) additional control buttons for acknowledging events, silencing audible circuits, and resetting the system. Model SSD-C has an integral key switch that enables these control buttons to operate. Model SSD-C-REM is located within a locked cabinet, so no additional key switch is required for enabling the control buttons. The SSD Series display is remotely connected to the H-Net communication bus from any Model NIC-C interface in a FireFinder XLS system enclosure using Class B, Style 4 or Class A, Style 7 wiring. 24VDC is required to run the SSD Series display, and can be provided from a Model PSC-12 Power Supply or PSX-12 Power Supply Extender in the FireFinder XLS system enclosure. Power from other UL Listed 24VDC power sources is also acceptable. The SSD Series display has screw terminals capable of supporting 12 to 22-gage wires. The H-Net communication from the FireFinder XLS system can be terminated on the SSD Series display, or may pass through for communication with other modules. Diagnostic LEDs on the SSD Series display indicate power and communication status. Models SSD and SSD-C can be mounted in a (2) two-gang electrical box or a (4) four-inch square electrical box. No flush-trim kit is required. The unit is approximately 10-1/2 (26.7cm.) wide, 6-1/8 (15.2cm.) high, and 1-1/2 (3.8cm.) deep. The Model SSD-C-REM is mounted in a Model REMBOX2 or Model REMBOX4 Remote Lobby Enclosure, or any CAB enclosure inner door. Model SSD-C-REM requires two (2) module spaces in the remote lobby enclosure, and its bracket supports the mounting of four (4) inner door modules (such as Model SCM-8 or Model LCM-8 modules) below the display. The inner door module spaces are arranged in two (2) rows of (2) two-module spaces. Products are UL 864 9th Edition listed for indoor dry locations within a temperature range of 120+/-3 F (49+/-2 C) to 32+/-3 F (0+/-2 C) and at a relative humidity of 93+/-2% at a temperature of 90+/-3 F (32+/-2 C). Model Number Details for Ordering Part Number Description SSD 500-034170 System-Status Display SSD-C 500-648733 System-Status Display [with control] SSD-C-REM 500-634773 System-Status Display [with control for remote-lobby enclosure] REMBOX2 500-633772 Small Remote-Lobby Enclosure REMBOX4 500-633914 Large Remote-Lobby Enclosure BCM 500-033320 Blank Control Module Plate Electrical Ratings Notes: An auxiliary regulated, power limited power supply may be used to provide power to Model SSD. The power supply must be UL Listed for Fire Protection Signaling Application. Be sure to also include Model SSD C in the battery calculations. Notes: An auxiliary regulated, power limited power supply may be used to provide power to Model SSD. The power supply must be UL Listed for Fire Protection Signaling Application. Notes: An auxiliary regulated, power limited power supply may be used to provide power to Model SSD C REM. The power supply must be UL / ULC approved for Fire Protection Signaling Application. Be sure to also include Model SSD C REM in the battery calculations. Notice: This marketing catalog sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.sbt.siemens.com/fis (SII) Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 August 2010 Supersedes sheet dated 5/10 (Rev. 3)

s Data Sheet Fire Safety & Security Products FireFinder TM XLS Fire Alarm Enclosures & Equipment Models: CAB1, CAB-BATT, CAB-BATT-R, CAB2-BB, CAB2-BD, CAB3-BB, CAB3-BD, CAB-MP, ID-MP, ID-SP, ID-FP, BCM, OD-LP, OD-BP, OD-GP, REMBOX2, REMBOX4, XLS-MLE6-ADPT, XLS-MME3-ADPT, XLS-MSE2-ADPT, XLS-MSE3-ADPT and XLS-RCC13F-ADPT ARCHITECT AND ENGINEER SPECIFICATIONS One (1), two (2), and (3) three-row enclosures for the FireFinder XLS system Blank plates for inner and outer doors Lens and grill plates for outer door UL 864 9 th Edition Listed and ULC Listed; FM, CSFM & NYMEA Approved Product Overview CAB1 CAB2 CAB3 The FireFinder XLS fire alarm enclosures (Models CAB1, CAB2, and CAB3) and their accessories provide a complete set of hardware for mounting all FireFinder XLS main system and remote transponder cards and modules. The hardware allows the FireFinder XLS system to be configured for a wide variety of applications, and allows for future system upgrades. Included in the enclosure series are backbox and door sets, removable mounting plates and clear lenses, louvered ventilation grill plates, and blank plates for use with the enclosure doors. All enclosures come with ground straps for the inner and outer doors, shield termination lugs, grounding lugs, and tie wrap lances for securing wire. All enclosures can also mount system backup batteries up to 31AH in capacity. Enclosures, Doors & Plates CAB1 Single-Row Enclosure Model CAB1, the smallest of the FireFinder XLS enclosures, can house a single Model CAB-MP cabinet mounting plate for mounting card cages, power supplies and bulk amplifiers. Model CAB1 also has four (4) mounting slots on the inner door for mounting a Model PMI interface and Model ID-MP switch module brackets. Model CAB1 comes complete with a black back box, with black inner and outer doors, a single lock and key set on the outer door, and a single OD-LP outer door lens plate (installed). A red version (Model CAB1-R) is also available. Approximate size is 27" (68.6cm.) high, 26" (66cm.) wide, and 8" (20.3cm.) deep. FireFinder TM XLS Enclosures 6327

Enclosures, Doors & Plates (cont. d) CAB1 Enclosure CAB2 Two-Row Enclosure Model CAB2 is the mid-sized FireFinder XLS enclosure capable of housing a maximum two (2) Model CAB-MP cabinet mounting plates. The inner door has two (2) rows of four (4) mounting slots. The outer door has space for mounting two (2) outer door plates (Models OD- LP, OD-BP or OD-GP). The outer door can be configured to open from either side. Model CAB2 consists of the Model CAB2-BB back box; the Model CAB2-BD black inner and outer door package, and one (1) Model OD-LP lens plate. The outer door has a single lock and key set installed. Red doors are available in Model CAB2-RD. Additional door mounting plates must be ordered separately. Approximate size is 45" (114.3cm.) high, 26" (66cm.) wide, and 8" (20.3cm.) deep. Enclosure Trim Kits Trim kits are available for all system enclosures for semi-flush mounting applications. Model CAB1-TK (for black enclosures) and Model CAB1R-TK (for red enclosures) fit Models CAB1 and CAB1-R enclosures. Similarly, Models CAB2-TK and CAB2R-TK fit the Model CAB2 enclosure, and Models CAB3-TK and CAB3R- TK fit the Model CAB-3 enclosure. Door Remote Transponders The FireFinder XLS system can use remote transponders for mounting additional modules such as amplifiers without requiring a Model PMI or any control switches. Special doors are available for systems using Model CAB2 or Model CAB3 remote transponders. These doors, Models CAB2-XBD and CAB3-XBD, omit the unused inner door and come complete with ventilation louvers built into the door. Model CAB2-XBD fits on Model CAB2-BB, and Model CAB3-XBD fits on Model CAB3-BB. The transponder doors are supplied in black. Complete box and door kits are available as Models CAB2-X and CAB3-X. CAB2 Enclosure CAB3 Three-Row Enclosure Model CAB3, the largest single FireFinder XLS enclosure available, can house a maximum three (3) Model CAB-MP cabinet mounting plates in the enclosure, and three (3) rows of inner door mounting slots. The outer door can be configured to open from either side. Model CAB3 consists of the Model CAB3-BB back box; the Model CAB3-BD black inner and outer door package, and one (1) Model OD-LP lens plate. The outer door has two (2) locks and key sets installed. Red doors are available via Model CAB3-RD. Additional door mounting plates must be ordered separately. Approximate size is 63" (160cm.) high, 26" (66cm.) wide, and 8" (20.3cm.) deep. CAB2-XBD Door CAB3-XBD Door OD-GP Outer-Door Grill Plate Model OD-GP also covers an entire row on the outer door of a system cabinet, but has four rows of ventilation louvers on it. Model OD-GP is mounted in front of system bulk amplifiers, card amplifiers, or other modules that generate heat. Using Model OD-GP will permit airflow across these modules to aid in heat dissipation. A single grill plate is included with each Model OG-GP. CAB3 Enclosure OD-GP Remote System Enclosures Models REMBOX2 and REMBOX4 are FireFinder XLS system enclosures that are used for remotely mounting inner-door modules, such as the Model PMI interface, switch modules, Model LVM live-voice modules, and Model FMT Firefighters Master Telephone modules.

Enclosures, Doors & Plates (cont. d) REMBOX4 are FireFinder XLS system are thinner than the regular CAB enclosures (just 5" deep overall), and are perfect for mounting in places where space is limited (such as lobbies or behind a receptionist s desk). Due to their smaller depth, no card cages, power supplies or bulk amplifiers can be mounted in a REMBOX. However, modules such as the Remote Network Interface Module (Model RNI); the Output-Control Module (Model OCM-16) and the Supervised Input Module (Model SIM-16) can be mounted in a REMBOX. Due to the depth of the live-voice module and the firefighters master telephone, no Model OCM-16 or Model SIM-16 modules can be used simultaneously with Model LVM or Model FMT. Both Models REMBOX2 and REMBOX4 are designed for flush mounting with no trim kit required. Both enclosures also come with a clear lens plate on the cover. REMBOX2 Two-Module Remote Enclosure Model REMBOX2 has two (2) inner door module spaces, and can hold a single Model PMI, up to two (2) switch module brackets, one (1) Model LVM live voice module. Combinations are also allowed. Model REMBOX2 can also mount a single Model RNI on a bracket included in the backbox. A bracket (Model REMBOX2-MP) can be used to mount up to four (4) Model OCM-16s or Model SIM-16 enclosures. Model REMBOX2- MP must be purchased separately. Approximate size of Model REMBOX2 is 14-1/2" (36.8cm.) wide, 18-1/2" (47cm.) high and 5" (12.7cm.) deep. REMBOX2 REMBOX2 (with doors closed) (with doors open) Note: A red, (2) two-module remote lobby enclosure (Model REMBOX2R) is also available. REMBOX4 Four-Module Remote Enclosures Model REMBOX4 has space for mounting four (4) inner door modules. Any combination of Model PMI (two-module spaces), switch module brackets, Model LVM or Model FMT (one-module space each) can be used. Unused module spaces can be covered with Model ID-SP blank plates. Model REMBOX4 can also mount to a single Model RNI on a bracket included in the backbox. A bracket known as Model REMBOX4-MP can be used to mount a maximum eight (8) Model OCM-16s or Model SIM-16s. Model REMBOX4-MP must be purchased separately. Approximate size of Model REMBOX4 is 24" (61cm.) wide, 18-1/2" (47cm.) high and 5" (12.7cm.) deep. REMBOX4 REMBOX4 (with doors closed) (with doors open) Note: A red, (4) four-module remote lobby enclosure (Model REMBOX4R) is also available. CAB-MP Cabinet Mounting Plate The cabinet mounting plate (Model CAB-MP) provides mounting for a single row of modules in a FireFinder XLS cabinet. Four (4)-module spaces are available on Model CAB-MP. Model CAB-MP is used to mount the Model CC-5 card cage, the Model CC-2 card cage, the Model PSC-12 power supply, the Model PSX-12 power supply extender, and the Model ZAM-80 / 180 zone amplifiers. CAB-MP ID-MP Inner Door Mounting Plate The inner door mounting plate (Model ID-MP) is mounted on the inner door of a CAB enclosure. Model ID-MP plates are used to mount Model SCM-8 switch control modules; Model LCM-8 LED control modules, or with Model FCM-6. Four (4) mounting plates are included in each Model ID- MP. Each mounting plate has four (4) spaces for control modules, and can hold either four (4) Model SCM-8 modules {one [1] control module space each}; four (4) Model LCM-8 modules {one [1] control module space each}; or two (2) Model FCM-6 modules {two [2] module spaces each}. Combinations are also allowed. Blank spaces in Model ID-MP can be covered using the Model BCM blank control module plate. A maximum four (4) Model ID-MP plates can be mounted in a single row on the inner door. ID-MP

Enclosures, Doors & Plates (cont. d) ID-SP Inner-Door Single Blank Plate Model ID-SP is used to cover any single module blank spaces on the inner door not used to mount the Model PMI or a Model ID-MP. Up to four (4) Model ID-SP plates can be mounted in a single row on the inner door. Two (2) blank plates are included in each Model ID-SP. XLS-MSE2/R-ADPT XLS MSE-2/R Enclosure Adapter Model XLS-MSE2-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MSE-2 small black enclosures. Model XLS-MSE2R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MSE-2R small red enclosures. ID-SP ID-FP Inner-Door Full Blank Plate Model ID-FP, which is a blank plate that covers the full opening of the row on an inner door, is used for applications requiring full dead-front protection. A single full blank plate is included with Model ID-FP. BCM Blank Control Module plate Model BCM is used on Model ID-MP to cover any blank areas where control modules are not used. A maximum four (4) Model BCM plates can be mounted on a single Model ID-MP. Four (4), blank-module plates are included in each Model BCM. XLS-MSE2-ADPT XLS-MME3/R-ADPT XLS MME-3/R or MBR-2 Enclosure Adapters Model XLS-MME3-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MME-3 or Model MBR-2 medium black enclosures. Model XLS-MME3R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MME-3R medium red enclosures. BCM OD-LP Outer Door Lens Plate Model OD-LP is a clear plastic lens plate mounted on the outer door of a system cabinet. Model OD-LP is used to allow operators to see the system interface and controls mounted on the inner door, but restricts access to unauthorized users. Model OD-LP covers an entire row on the outer door. A single lens plate is included with each Model OD-LP. OD-BP Outer-Door Blank Plate Model OD-BP is used to cover an entire row on the outer door of a system cabinet. Model OD-BP is used when there is no Model PMI or control modules mounted on the adjacent row of the inner door. A single blank plate is included in each Model OD-BP. XLS-MME3-ADPT XLS-MLE6/R-ADPT XLS MLE-6/R Enclosure Adapter Model XLS-MLE6-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL Model MLE-6 large black enclosures. Model XLS-MLE6R-ADPT, which must be used in conjunction with Model CAB-MP, is an adapter that allows FireFinder XLS cards to be mounted in oldergeneration MXL MLE-6R large red enclosures. OD-BP XLS-MLE6-ADPT

Enclosures, Doors & Plates (cont. d) XLS-MSE3/R-ADPT XLS MSE-3L/R or MSE-3M/R Enclosure Adapters Model XLS-MSE3-ADPT is an adapter that allows FireFinder XLS cards to be mounted in the older generation MXL-IQ Model MSE-3L or Model MSE-3M black enclosure. Model XLS-MSE3R-ADPT is an adapter that allows FireFinder XLS cards to be mounted in the older generation MXL-IQ Model MSE-3LR or Model MSE-3MR red enclosure. XLS-MSE3-ADPT XLS-RCC-1-ADPT XLS RCC-1 Enclosure Adapter Model XLS-RCC1-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in the older generation Model RCC-1 surface-mount enclosure. XLS-RCC1-ADPT XLS-RCC13F/R-ADPT XLS RCC-1F/R or RCC-3F/R Enclosure Adapters Model XLS-RCC13F-ADPT is an adapter that allows the FireFinder XLS Model SSD/-C series remote annunciator to be mounted in the older generation Model RCC-1F or Model RCC-3F black, flush-mount enclosure. Model XLS-RCC13FR-ADPT is an adapter that allows the Model SSD/-C series to be mounted in the older generation RCC-1FR red and RCC-3FR red flush-mount enclosure. XLS-RCC13F-ADPT Temperature and Humidity Range Products are UL 864 9 th Edition listed for indoor / dry locations within a temperature range of 120+/-3 F (49+/-2 C) to 32+/-3 F (0+/-2 C) and a relative humidity of 93+/-2% at a temperature of 90+/-3 F (32+/-2 C). Details for Ordering Model Number Part Number Description BCM 500-033320 Blank control module plate, four [4] per package CAB-1 500-633007 Complete single-row cabinet, black CAB-1R 500-633728 Complete single-row cabinet, red CAB1-TK 500-633013 Single-row trim-kit cabinet, black CAB1R-TK 500-633729 Single-row trim-kit cabinet, red CAB2-BB 500-633009 (2) Two-row back box, black CAB2-RB 500-634941 (2) Two-row back box, red CAB2-BD 500-633008 (2) Two-row inner & outer door set, black CAB2-RD 500-633755 (2) Two-row inner & outer door set, red CAB2-TK 500-633014 (2) Two-row trim-kit cabinet, black CAB2R-TK 500-633753 (2) Two-row trim-kit cabinet, red CAB2-XBD 599-633768 CAB2 transponder door CAB2-X Complete CAB2 w/ transponder door 599-034252 [no inner door] CAB3-BB 500-633011 (3) Three-row back box, black CAB3-RB 500-634942 (3) Three-row back box, red CAB3-BD 500-633010 (3) Three-row inner & outer door set, black CAB3-RD 500-633757 (3) Three-row inner & outer door set, red CAB3-TK 500-633015 (3) Three-row trim-kit cabinet, black CAB3R-TK 500-633754 (3) Three-row trim-kit cabinet, red CAB3-XBD 599-633769 CAB3 transponder door CAB3-X Complete CAB3 w/ transponder door 599-034253 [no inner door] CAB-BATT Field-mounted enclosure for 100AH 500-633917 batteries, black CAB-BATT-R Field-mounted enclosure for 100AH 500-634925 batteries, red CAB-MP 500-633012 Back box module mounting plate ID-FP 500-633029 (4) Four module inner-door blank plate ID-MP Inner-door enclosure mounting plate, 500-633027 four [4] per package ID-SP Single-module inner-door enclosure 500-633028 mounting plate [two (2) per package] OD-BP 500-633017 Outer door blank plate OD-BP-R 500-634919 Outer door blank plate, red OD-GP 500-633018 Outer door grill plate OD-GP-R 500-634920 Outer door grill plate, red OD-LP 500-633016 Outer door lens plate REMBOX2 500-633772 (2) Two-module remote lobby enclosure, black REMBOX2R 500-650612 (2) Two-module remote lobby enclosure, red REMBOX2-MP Mounting plate for Models OCM-16 / 500-634211 SIM-16 in Model REMBOX2 REMBOX4 500-633914 (4) Four-module remote lobby enclosure, black REMBOX4R 500-650613 (4) Four-module remote lobby enclosure, red REMBOX4-MP Mounting plate for Models OCM-16 / 500-634212 SIM-16 in Model REMBOX4 XLS-MLE6-ADPT S54430-C9-A1 MLE-6 enclosure adapter for XLS, black XLS-MLE6R-ADPT S54430-C9-A2 MLE-6R enclosure adapter for XLS, red MME-3 and MBR-2 enclosure adapters XLS-MME3-ADPT S54430-C8-A1 for FireFinder XLS, black XLS-MME3R-ADPT S54430-C8-A2 MME-3R enclosure adapter for XLS, red XLS-MSE2-ADPT S54430-C7-A1 MSE-2 enclosure adapter for XLS, black XLS-MSE2R-ADPT S54430-C7-A2 MSE-2R enclosure adapter for XLS, red XLS-MSE3-ADPT MXL-IQ MSE-3L and MSE-3M enclosure S54430-C14-A1 adapters for XLS, black MXL-IQ MSE-3LR & MSE-3MR enclosure XLS-MSE3R-ADPT S54430-C14-A2 adapters for XLS, red XLS-RCC1-ADPT S54430-Z14-A1 RCC-1 enclosure adapter, black XLS-RCC13F-ADPT S54430-Z13-A1 RCC-1F & RCC-3F enclosure adapters, black XLS-RCC13FR-ADPT S54430-Z13-A2 RCC-1FR & RCC-3FR enclosure adapters, red

Notice: This marketing data sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.sbt.siemens.com/fis (SII FS) Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 October 2011 Supersedes sheet dated 8/11 (Rev. 7)

s Data Sheet Fire Safety & Security Products Intelligent Detection Devices Intelligent Thermal Detector [For use with FireFinder XLS and FS-250 Panels] Model HFP-11 ARCHITECT AND ENGINEER SPECIFICATIONS Most sophisticated detector intelligence available FirePrint technology to differentiate between deceptive phenomena and an actual fire Easily programmed to match specific hazard profiles from the fire alarm control panel (FACP) Supports software-based automatic environmental compensation System logic activation based on any of three (3) inputs from the detector (smoke, heat or neural network) Remote sensitivity-measurement capability Pre-alarm reporting based on fire-profile selection Polarity insensitive utilizing SureWire TM technology Multi-color detector status light-emitting diode (LED) Compatible with Model DPU (device programmer / tester unit) Field-cleanable chamber with replaceable chamber parts available Multi-criteria fire detection for the price of a photoelectric detector Optional fully programmable relay base, audible base and duct housing Detectors are self-testing: complete diagnostics every four seconds Two-wire operation Product Overview Model HFP-11 utilizes advanced detection technology that allows each detector to distinguish nonthreatening deceptive phenomena such as cigarette smoke, from actual fire hazards, while optimizing detection for the area it is intended to detect. Model HFP-11 uses state-of-the-art microprocessor circuitry with error check, detector self-diagnostics and supervision programs. Model HFP-11 is compatible with the Siemens Fire Safety field device program / test unit (Model DPU), which is a compact, portable, menu-driven accessory for electronically programming and testing detectors, easily and reliably. Model DPU eliminates the need for cumbersome, unreliable mechanical programming methods such as dials or switches, and reduces installation and service costs by electronically programming and testing the detector prior to installation. Model HFP-11 is compatible with FS-250 and Fire Finder XLS FACPs. UL and ULC Listed; FM, CSFM & NYC Fire Department Approved Model HFP-11 is Underwriters Laboratory and Underwriters Laboratory of Canada listed. Specifications Model HFP-11 is a plug-in, two-wire and multi-sensor detector (with both photoelectric and thermal inputs) that is compatible with FireFinder XLS and FS-250 series of FACPs. Each detector consists of a dust-resistant, field-cleanable and photoelectric chamber; a solid state, non-mechanical thermal sensor, and microprocessor-based electronics with a low-profile plastic housing. Model HFP-11 utilizes state-of-the-art ASIC circuitry and surface-mount technology for maximum reliability. Every Model HFP-11 fire detector is shipped with a protective dust cover. Model HFP-11 utilizes an infrared light emitting diode (IRLED), and light-sensing photodiode. Under normal conditions, light transmitted by the LED is directed away from the photodiode and scattered through the smoke chamber in a controlled pattern. Addressable FirePrint TM Detector 6301

Specifications (continued) The smoke chamber is designed to manage light dissipation and extraneous reflections from dust particles or other non-smoke, airborne contaminants in such a way as to maintain stable, consistent detector operation. When smoke enters the detector chamber, light emitted from the IRLED is scattered by the smoke particles, and is received by the photodiode. Model HFP-11 also utilizes a modern, accurate and shock-resistant thermistor to sense temperature changes. The on-board FirePrint TM technology allows the detector to first gather smoke and thermal data, and then analyze this information in the detector s neural network. By comparing data received with the common characteristics of fires or fire fingerprints, Model HFP-11 can compare these fire prints to those of deceptive phenomena that cause other detectors to false alarm. FirePrint The advanced FirePrint technology allows Model HFP-11 to accurately determine a true fire hazard from unthreatening, deceptive phenomena. Further, the advanced FirePrint technology will not require a need to use alarm-delaying verification and confirmation techniques, which can increase the probability of losses due to fire. Model HFP-11 provides the highest level of detector intelligence available today with a detector / control panel link that allows the user to program the detector for the specific hazard profile, using a simple software menu selection. Model HFP-11 s FirePrint application monitors input from both the photo chamber and the thermal sensor, evaluating this information with sophisticated mathematical formulas or algorithms, comparing this input to characteristics of both threatening fires and deceptive phenomena that would mislead any ordinary detector. Detectors are optimized by selecting one (1) of the following 11 applications: Office / Retail Lobby Computer room Dormitory Healthcare Parking garage Utility / Transformer room Hostile environment Precious storage Air Duct Warehouse / Light Manufacturing The control panel programs Model HFP-11 detector for the protected area without hassle and without confirmation delays. Once optimized for the hazards in the protected area, Model HFP-11 provides the best detection. Should the operator or installer forget to program the detector, Model HFP-11 will revert to a default setting, allowing operation as an office-environment detector. The FirePrint technology was developed over years of research and reviewing the results of over 20 years of fire test data in one of the world s most advanced fire-research centers. The results of this research are the mathematical models that form the algorithms used in FirePrint. No other fire detector has this level of intelligence or this amount of research and development supporting its design. The microprocessor s software can identify and disregard false input caused by radio frequency (RFI) and electromagnetic (EMI) interference, while validating all Trouble conditions before annunciating or reporting to the FACP. Model HFP-11 The Model HFP-11 detector s microprocessor uses an essential electronically erasable programmable read-only memory (EEPROM) to store the detector s address and other critical operating parameters, including the assigned program values for Alarm and Trouble thresholds. Communication within the detector, as well as between Model HFP-11 and the control panel, or with Model DPU (field device programmer / test unit), are supervised and safe-guarded against disruption by reliable, microprocessor-based error checking routines. Additionally, the micro-processor supervises all EEPROM memory locations, and provides a high degree of EEPROM-failure fault tolerance. Model HFP-11 determines its operating status to be Normal in Alarm or in Trouble modes, depending on the difference between the alarm threshold values stored in the detector s memory and the detector s latest analog measurement. The detector then communicates changes in its status to the control panel. In addition, the FireFinder XLS control panel will sample the value of the analog signal for Model HFP-11 over a period of time, in order to determine if those values indicate excessive buildup in the photo chamber. If such is the case, the FireFinder XLS control panel will indicate the particular detector requires maintenance. Model HFP-11 is listed as a self-testing device. The visible light emitting diode (LED) for Model HFP-11 flashes green every four (4) seconds to indicate it is communicating with the control panel, as well as to indicate it has passed its internal self-test. Should the detector sense a fault or failure within its systems, the LED will flash amber, and the detector will transmit that data to the control panel. A quick visual inspection is enough to indicate the condition of the detector at any time. If more detailed information is required, a printed report can be provided from the FireFinder XLS FACP, indicating the status and settings assigned to each individual detector. When Model HFP-11 moves to the Alarm mode, it will flash red, and will continue flashing until the system is reset at the FACP. Simultaneously, any user-defined, system-alarm functions programmed into the system are activated.

Specifications (continued) Detector sensitivity, calibration and identification are dynamically supervised at the respective FACP. Detector sensitivity and pre-alarm levels are a function of the application chosen at the control panel, and are controlled by the panel. If an alternate, non-fireprint mode is selected, then the sensitivity can be changed from the control panel. All Model HFP-11 detectors use a surface mounting base, Model DB-11, which mounts on a 4-inch octagonal, square or single gang electrical box. The base utilizes screw-clamp contacts for electrical connections and self-wiping contacts for increased reliability. Model DB-11 can be used with the optional Model LK-11 detector locking kit, which contains 50 detector locks and an installation tool to prevent unauthorized removal of the detector head. Model DB-11 has integral decorative plugs to cover the outer mounting screw holes. Model HFP-11 may be installed on the same initiating circuit with Model HMS-series manual stations; Model HTRI-series interfaces; Model HCP output-control devices, or Model HZM series of addressable, conventional zone modules. All Model HFP-11 detectors can be cleaned in the field when required via easily removing the detector cover and unsnapping the photo chamber. There is also the option of cleaning the interior of the detector with a clean, soft cloth or brush or by replacing the labyrinth and bug screen included in the detector maintenance kit, Model DMK-11. All Model HFP-11 detectors are approved for operation within the UL-specified temperature range of 32 to 100 F (0 to 38 C). Model DPU The Device Program / Test Unit accessory is used to program and verify the address of the detector. The technician selects the accessory s program mode, and enters the desired address. Model DPU automatically sets and verifies the address and tests the detector. Model DPU operates on AC power or rechargeable batteries, providing flexibility and convenience in programming and testing equipment from practically any location. When in test mode, Model DPU will perform a series of diagnostic tests without altering the address or other stored data, allowing technicians to determine if the detector is operating properly. Application Data Installation of the Model HFP-11 series of fire detectors requires a two-wire circuit. In many retrofit cases, existing wiring may be used. T-tapping is permitted only for Style 4 (Class B) wiring. Model HFP-11 is polarity insensitive, which can greatly reduce installation and debugging time. Model HFP-11 fire detectors can be applied within the maximum 30 foot center spacing (900 sq. ft. areas,) as referenced in NFPA 72. This application guideline is based on ideal conditions, specifically, smooth ceiling surfaces, minimal air movement, and no physical obstructions between potential fire sources and the actual detector. Do not mount detectors in close proximity to ventilation or heating and air conditioning outlets. Exposed joints or beamed ceilings may also affect safe spacing limitations for detectors. Should questions arise regarding detector placement, observe NFPA 72 guidelines. Good fire-protection system engineering and common sense dictate how and when fire detectors are installed and used. Contact your local Siemens Fire Safety distributor or sales office whenever you need assistance applying FirePrint in unusual applications. Be sure to follow NFPA guidelines and UL Listed / ULC Listed installation instructions included with every Siemens Fire Safety detector and local codes as for all fire protection equipment. Technical Data Operating Temperatures: Relative Humidity: 0-93% Non-condensing Maximum Spacing: Current Draw: +32 F (0 C) to 100 F (38 C), per UL 268 / 268A 30-foot Centers (900 Square Feet), per NFPA 72 Chapter 5 and ULC-S524 1mA in Alarm or Supervisory mode

Mounting Diagram Model Number Details for Ordering Part Number Description HFP-11 500-033290 Addressable FirePrint TM Fire Detector DB-11 500-094151 Detector Mounting Base for Series 11 DB-11E 500-094151E Detector Base {small} AD2-P 500-649706 Air-Duct Housing AD2-XHR 500-649708 DB-HR 500-033220 ADBH-11 500-033210 RL-HC 500-033230 RL-HW 500-033310 LK-11 500-695350 DMK-11 500-695338 Model Number Part Number DB-11C 500-095687 Air-Duct Housing {with relay} Relay Base for H-Series Intelligent Detectors Audible Base Remote Alarm Indicator: 4 octagon-box mount, red Remote Alarm Indicator: Single-gang box mount, red Base Locking Kit for Series 11 Detectors Series 11 Maintenance Kit {replacement labyrinth and bug screen} In Canada, order Description Detector Mounting Base for Series 11 Detectors ( ULC) Notice: This marketing data sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.usa.siemens.com/fire [SII-FS] Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 September 2013 Supersedes sheet dated 10/10 (Rev. 4)

s Data Sheet Fire Safety & Security Products HTRI-Series Interface Modules Models HTRI-D, HTRI-R and HTRI-S ARCHITECT AND ENGINEER SPECIFICATIONS Interfacing and supervising normally open (N.O) or normally closed (N.C) contacts Integral single-pole, double-throw (SPDT) relay on Model HTRI-R (up to 4 amps) Dual input on Model HTRI-D, using a single address Polarity insensitive with SureWire TM technology Multi-color light-emitting diode (LED) indicates system status: green / amber / red Easy front access to programming port and wiring terminals Mounts in a 4-inch square, 2-¼ -deep box (or double-gang box) Dynamic supervision Comes with 5-x-5 faceplate Two-wire operation Device Programmer / Tester programs and verifies address of the device and tests for proper functionality Electronic address programming is easy and dependable UL Listed & ULC Listed; FM, CSFM and NYC Fire Department Approved Product Overview The Siemens Fire Safety HTRI-series Intelligent interface modules are designed to provide the means of interfacing direct shorting devices to the fire-alarm control panel (FACP) loop circuit. The HTRI-series modules provide the most advanced method of address programming and supervision on the market combined with sophisticated control panel communication. Each HTRI-series interface module incorporates a microcomputer chip, and each interface module achieves the state of an intelligent device through its microcomputer chip technology, combined with its sophisticated, bi-directional communication capabilities with the FACP. Specifications The HTRI-series intelligent interface modules are available in three (3) models. Models HTRI-S and HTRI-R are designed to monitor a (N.O) or (N.C) dry contact. The interface module reports the status of the (N.O) or (N.C) contact to the control panel. Model HTRI-S can only monitor and report the status of the contact, while Model HTRI-R incorporates an addressable Form C relay. The Model HTRI-R relay and contact device input are controlled at the same address. For the FACP, the relay and input contact can be controlled as a separate function. The relay is typically used where control or shunting of external equipment is required. The Model HTRI-D is a dual-input module that is designed to supervise and monitor two (2) sets of dry contacts. Model HTRI-D only requires one (1) address, but responds independently to each input. Model HTRI-D is ideal for monitoring a water-flow switch and its respective valve tamper switch. Model HTRI has a multi-color LED that flashes green when operating in Normal; amber if unit is in Trouble condition, and red to indicate a change of state. HTRI Series Interface Modules 6304

Specifications (continued) Model HTRI-D flashes twice once for each address, and Model HTRI-R LED indicates a change of state in the relay. The device s microcomputer chip has the capacity of storing, in memory, identification information; as well as important operating-status information. Siemens Fire Safety innovative technology allows all HTRI-series intelligent interface modules to be programmed via the Device Programming / Test Unit: a compact, portable and menu-driven accessory that makes programming and testing an interface device faster, easier and more dependable than previous methods. The programmer / tester eliminates the need for mechanical addressing mechanisms, such as: program jumpers, DIP switches or rotary dials, since Model DPU electronically sets the HTRIseries interface address into the non-volatile memory of the interface microcomputer-chip. Vibration, corrosion and other conditions that deteriorate mechanical addressing mechanisms are no longer a cause for concern. The HTRI-series is fitted with screw terminals for connection to an addressable circuit, and is fully compatible on the same Siemens FACPs with all intelligent H -series detectors, HMS -series addressable manual stations, or any other addressable intelligent modules, such as Model HZM or Model HCP. All HTRI-series intelligent interface modules are UL Listed. Environmental operating conditions for all HTRI-series modules are 32ºF (ºC) to 120ºF (49ºC) with a relative humidity of no greater than 93%, non-condensing. Electrical Ratings Current Draw (Active or Standby) 1mA Mounting Diagram Models HTRI-S, HTRI-D and HTRI-R mount directly into a 4-inch square, 2 ¼-deep box or to a user-supplied double-gang box. A 5-inch square, off-white faceplate is included with each HTRI-series module. Details for Ordering Model HTRI-R Relay Ratings Resistive: 4 Amps, 125 VAC 4 Amps, 30 VDC Inductive: 3.5A, 120 VAC (0.6P.F.) 3.0A, 30 VDC (0.6P.F.) 2.0A, 120 VAC (0.4P.F.) 2.0A, 120 VAC (0.35P.F.) 2.0A, 30 VDC (0.35P.F.) Notice: This marketing data sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.sbt.siemens.com/fis (SII) Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 December 2011 Supersedes sheet dated 6/10 (Rev. 2)

s Data Sheet Fire Safety & Security Products Intelligent Initiating Devices HMS-Series Models HMS-D, HMS-S Durable design Shock-and-vibration resistant Pull-down lever is down, until manually reset Reset with Allen Key No break rods necessary Custom microcomputer-chip technology Dynamic supervision to the fire-alarm control panel (FACP) Polarity insensitive via SureWire TM technology Two-wire operation Surface or semi-flush installation Model DPU programs and verifies address and tests functionality of each device Electronic-address programming is easier, more efficient and more dependable Comes in single-action (Model HMS-S) and double-action (Model HMS-D) stations UL Listed; FM, CSFM & NYC Fire Dept. Approved Product Overview ARCHITECT AND ENGINEER SPECIFICATIONS The Siemens intelligent manual fire-alarm boxes (Models HMS-S and HMS-D) provide the most advanced method of address programming and supervision. Each Model HMS-series manual box achieves the state of an intelligent-initiating device by incorporating custom microcomputer-chip technology with sophisticated, bi-directional communication capabilities with the FACP. Specifications Models HMS-S and HMS-D are constructed of durable, molded polycarbonate material that is matte finished in red with raised white lettering. The housing accommodates a pull-down lever, which when operated locks into position; indicating the manual fire-alarm box has been activated. The pull down lever remains down / in the locked position, until the fire-alarm box is manually reset. The manual fire alarm box can only be reset by opening the hinged housing cover with an Allen key; followed by closing and locking the cover. Model HMS-D Dual-Action Station Model HMS-S Single-Action Station Models HMS-S and HMS-D operate with Siemens Fire Safety FACPs. The microcomputer chip to the manual fire-alarm box has the capacity of storing in memory identification information as well as important operating-status data. Innovative technology from Siemens Fire Safety also allows all Model HMS-series intelligent manual fire-alarm boxes to be programmed via the Device Programmer / Test Unit (Model DPU). Model DPU is a compact, portable and menu-driven accessory that makes programming and testing of a manual firealarm box device faster, easier and more dependable than previous methods. The programmer / tester eliminates the need for mechanical-addressing mechanisms of a device because Model DPU electronically sets the address of the manual fire-alarm box into its microcomputer chip, non-volatile memory. Hence, vibration, corrosion and other conditions that can compromise or even deteriorate mechanical-addressing mechanisms are no longer a cause for concern. HMS Series Intelligent Initiating Devices 6306

Specifications (continued) Models HMS-S and HMS-D are fitted with screw terminals for connection to an addressable circuit, and can be either surface or semi-flush mounted. The Model HMS-series manual fire-alarm boxes derive their power, communicate information and receive commands over a single pair of wires. The Model HMS-series is compatible on the same circuit with all Model H -series detectors, interfaces or addressable, conventional zone modules. Electrical Ratings Current Draw (Active or Standby) 1.5mA Model Number Details for Ordering Part Number Description Shipping Weight HMS-D Addressable Manual Fire 500-033400 2.5 Lbs. 1.13 Oz. Alarm Box, Dual Action HMS-S Addressable Manual Fire 500-033200 2.0 Lbs. 0.9 Oz. Alarm Box, Single Action LTP 500-620490 Reset Tool Package [contains two (2) tools] 0.5 Lb. 0.23 Oz. SB-5R 310-019860 Surface-Mounting Box 1.5 Lbs. 0.7 Oz. Mounting Diagram Notice: This marketing data sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.usa.siemens.com/fire (SII) Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 September 2013 Supersedes sheet dated 2/13 (Rev. 4)

s Catalog Sheet Fire Safety & Security Products Air-Duct Housings and Detectors Air-Duct Housings AD2 Series Models AD2-P, AD2-PR, AD2-XHR, AD2-4W, ST(s): 10, 25, 50 and 100 ARCHITECT AND ENGINEER SPECIFICATIONS For use with Series 11 detectors Relay models available Design for air-velocity range of 100 to 4,000 fpm Alarm LED visible from front Self-contained model available with on-board power supply Clear housing cover for quick identification of detector type; removable with only four (4) captive screws UL and ULC Listed; FM, CSFM & NYMEA Approved Product Overview The Siemen Fire Safety Air-Duct Detector Housings are designed to be used with the Series 11 detectors. Designed for installation directly to heating, ventilating and air-conditioning duct systems, they comply with National Fire Protection Association Standard No. 90A. When equipped, the air-duct detector housing will signal the presence of smoke being carried through the duct system. Air-duct detectors are not intended to be substituted for open-area detection. Air-duct housings can be equipped with optional relays, which are utilized to operate any supplementary equipment when smoke is detected. Notes: Most conventional time-control equipment guarantee only one (1) detector per zone when the detector operated relay function is critical. The connection of a remote lamp and a remote relay per detector is allowed with PXL or System 3 TM only; other conventional systems may use either a remote lamp or a relay. Notes - (cont. d): With the MXL series of control panels, up to 60 detectors (per circuit) having relays may be used. The connection of a remote lamp or a remote relay is allowed for each detector, but not simultaneously. With the FireFinder XLS series of control panels, up to 252 detectors (per circuit) having relays may be used. The connection of an intelligent remote lamp (ILED) and a remote Relay is allowed for each detector simultaneously. Air-duct housings (see: Details for Ordering) are Underwriters Laboratories, Inc. listed. Specifications The air-duct housings are uniquely designed to use with the photoelectric detector. Sensitivity of PE-11 detectors can be checked by viewing the LED or a RSAW- 11 or RSAC-11 multicolor remote lamp. A green flash indicates the detector has passed its self test. Amber indicates a Trouble condition, and red indicates an Alarm state. HFP-11, HFPO-11 and FP-11 sensitivity may be viewed from the multi-color LED on the detector or, preferably, may be printed by command on an optional printer from the MXL control panel. Air-Duct Housings and Detectors 6185

Specifications (continued) The detector unit employs a cross-sectional sampling principle of operation. Inlet sampling tubes are available in four (4) lengths (see: Sampling Tube Selection Table). Outlet sampling tubes are one (1) common length and draw. A continuous, cross-sectional sample of air moves through the duct. Stratification or skin affect phenomenon that occurs in the duct can prevent smoke (especially in large ducts) from reaching a spot-type detector. In addition, the unique design of the sampling chamber insures uniform sensitivity in air velocities, ranging from a low of 10- feet-per-minute to as high as 4,000- feet-per-minute. Each housing comes with three (3) wiring entry ports: Two (2) 3/4 conduit knockouts One (1) 1/2 conduit opening The inlet sampling tube length is determined by the width of the air duct being protected. The inlet tube greater than and nearest to the duct width should be used (see: Sampling Tube Selection Table). The inlet tube can then be trimmed at the job site to the exact width of the duct. The outlet sampling tube for all ducts irrespective of width has a fixed length of approximately 5.5 inches (14cm.), and is supplied with the air-duct housing. Note: When the use of a remote relay is required, order model AD2-PR for conventional systems; AD2-XHR for addressable systems. When required the WP-2000 weatherproof enclosure for duct housing is available. (For full details, refer to installation instructions part number 315-049708.) Note: When a self-contained duct detector with power supply is required, order model AD2-4W. (For full details, refer to installation instructions part number 315-049708.) Sampling Tube Selection Table Duct Width For duct widths 6 to 1 For duct widths 1 to 3 For duct widths 3 to 5 (requires support) For duct widths 5 to 10 (requires support) Sampling Tube (Model No.) ST-10 ST-25 ST-50 ST-100 Maintenance of the detector is easily accomplished by the removal of the Series 11 duct-housing sampling chamber cover. The detector, which plugs into the housing, is easily removed for cleaning by a trained technician. All that is necessary for installation of the air-duct detector is the cutting of three (3) small holes for the Sampling Tube installation (template included), and the drilling of two (2) holes for mounting the air-duct housing. The unit is then easily mounted in place, and connection made to the existing wires or terminals if optional accessories are utilized. (For full details, refer to installation instructions part number 315-049708-4.) ST-50 and ST-100 require support. ST-100 is shipped in two (2) 5-ft. (152 cm.) pieces with a coupling for field assembly. Technical Data Temperature Range: 32 F (0 C) -100 F (38 C) Altitude Range: No Altitude Limitations Relative Humidity: 10-85% (non-condensing / non-freezing) Air-Duct Velocity Range: 100-4,000 Ft. /Min. Sampling Tube Pressure Range of Differences: Greater than 0.01 inches; less than 1.2 inches of water column Note to Architect: When building codes regulate the location of detectors within ventilating systems, make sure the number and locations of detectors is in accordance with the code regulations. Details for Ordering Model Number Part Number Description AD2-P 500-649706 Air-Duct Housing for use with FP-11, HFP-11, HFPO-11 and PE-11 AD2-PR 500-649707 Air-Duct Housing for use with PE-11 relay AD2-XHR 500-649708 Air-Duct Housing for use with FP-11, HFP-11 and HFPO-11, with relay AD2-4W 500-649709 Self-contained Air-Duct Housing with on board power supply and relay ST-10 500-649710 Sampling tube for Ducts 6 to 1 ST-25 500-649711 Sampling tube for Ducts over 1 to 3 ST-50 500-649712 Sampling tube for Ducts 3 to 5 ST-100 500-649713 Sampling tube for Ducts 5 to 10 Product Includes: - (1) short-return (outlet) tube - (1) stopper - (2) #12 + 3/4 sheet-metal screws - (1) mounting template Note: Detector and sampling tube to be purchased separately. Minimum hardware required is: one (1) air-duct housing assembly; one (1) sampling tube and one (1) detector. Notice: This marketing catalog sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.sbt.siemens.com/fis SFS Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 December 2009 Supersedes sheet dated 9/09 (Rev. 2)

s Catalog Sheet Fire Safety & Security Products FireFinder XLS and FS-250 Detectors Remote Alarm Lamps Models RL-HC and RL-HW Model RL-HW [Wall] Multi-color LED (green, amber, red) mimics detector Becomes second accessory (used with relay or audible base) Can be addressed and independently controlled by panel logic Can be installed anywhere on the H -series device circuit UL Listed and ULC Listed; FM, CSFM & NYMEA Approved Model RL-HC [Ceiling] Product Overview The Remote Alarm Lamps (Models RL-HW and RL-HC) are designed for use with initiating devices that are concealed or otherwise not exposed to view (e.g. in false ceilings, under sub-floors, in unexposed ventilating ducts, normally locked vaults, within computer consoles, etc.) Even though the device initiating the alarm is out of sight, these remote alarm-lamp assemblies will readily identify the aforementioned non-concealed initiating devices. Model RL-HC is designed for mounting to a 4 octagon outlet box, and Model RL-HW is designed for mounting on a standard single-gang switch box. Although there is no mounting limitation, Model RL-HC is normally ceiling mounted, while Model RL- HW is normally mounted to a wall. The remote lamps may be placed up to 25 feet from the detector and use 14-to-18 gauge, 3-conductor wire. The light-emitting diode (LED) can be controlled by panel logic even on different device loops, or on another panel in the network configuration, since Model RL-HC or Model RL-HW is given its own unique address. Specifications The Remote Alarm Lamps can be mounted anywhere on the H -series device loop, and are addressed with the Device Program / Tester Unit (Model DPU). Models RL-HW and RL-HC have screw-type terminals for ease of installation. The mounting plates for both units are comprised of an offwhite plastic, presenting an attractive appearance that will blend with any decor. Details for Ordering Model Number Part Number Description RL-HC 500-033230 Remote Lamp, Ceiling RL-HW 500-033310 Remote Lamp, Wall FireFinder XLS 6307

Mounting Diagram Model RL-HC [Ceiling] Model RL-HW [Wall] Notice: This marketing catalog sheet is not intended to be used for system design or installation purposes. For the most up-to-date information, refer to each product s installation instructions. Fire Safety 8 Fernwood Road Florham Park, NJ 07932 Tel: (973) 593-2600 FAX: (908) 547-6877 URL: www.sbt.siemens.com/fis (SII) Printed in U.S.A. Fire Safety 2 Kenview Boulevard Brampton, Ontario L6T 5E4 / Canada Tel: (905) 799-9937 FAX: (905) 799-9858 July 2010 Supersedes sheet dated 12/04 (Rev.1)

Operations Matrix shall include Waterflow, Tamper, or Other Sprinkler Valve Events. In the event of a Waterflow, a general evacuation notification (horns & strobes) and a "Northeast Waterflow AFA" signal should be sent to the Monitoring System. In the event of a tamper or other sprinkler valve event (air hi/lo for example), a "Supervisory" signal should be sent to the Monitoring system. Boeing Comment, George Wangersky, 2/18/2014 Design is acceptable pending final field review and testing and the following comment: The Duct Detectors should be monitored as a "Supervisory Trouble Alarm". Boeing Comment, Robert Eaker, 2/20/2014 Siemen

SIEMENS * * * SIEMENS Siemen