Section 5 Integrated handle design kitchen Integrated handles Corner base cabinet fillet fixing... page 112 Jointing plate... page 113 Pull out larder bracket.... page 114 Appliance door applications... page 115 Curved base decor end and door fixing.... page 119 www.howdens.com 111
Corner base cabinet fillet fixing Assembly 1 Fit two fixing blocks each side of the fillet top and bottom. Flush Top 18mm 40mm (minimum) KB block x4 Screw x4 (25mm) KD block x4 Screw x4 (25mm) 2 Position the fillet to the cabinet centre upright and secure. Bottom KD block Screw x4 (25mm) 18mm 18mm 400/500mm Door 3 Adjoining cabinet fixing position. Screw x4 (25mm) 56mm Door KD block 56mm KD block 112 www.howdens.com
Jointing plate This leaflet shows jointing plate applications and fitting information. Fitting Slab and shaker style door applications. Integrated handle style door applications. Short Long Applications Small jointing plate applications. (Typically used on slab and shaker style) Large jointing plate applications. (Typically used on integrated handle style) Dummy Drawer Line Dummy Drawer Line Corner Dummy Drawer Line High Line Corner Base* High Line Corner Wall* Larder Doors *Also applies to integrated handle style doors. NOTE: Some pull-out larder accessories require accessory plates supplied with the product. Dummy Drawer Line Corner Larder/Tower Doors Pull-Out Larder Doors www.howdens.com 113
Assembly Section 5 - Integrated handle design kitchen Pull out larder bracket Position the bracket and jointing plates to the back of the frontals following the dimensions shown. These dimensions replace the ones shown on the leaflet supplied with the pull-out larder units for bracket fixing, when used with the integrated handle range. Chamfered and J trim door design 32mm 2mm 20mm Bracket x1 55mm 50mm Jointing plate x2 114 www.howdens.com
Appliance door applications IMPORTANT NOTICE The following pages cover the appliances listed below: LAM8605 - Lamona deluxe fully integrated dishwasher LAM8302 - Lamona slimline fully integrated dishwasher LAM8303 - Lamona eco deluxe fully integrated dishwasher HBH8602 - Bosch fully integrated dishwasher HJA6312 - Lamona built-under integrated larder fridge HJA6132 - Lamona built-under integrated fridge LAM6400 - Lamona built-under integrated freezer IMPORTANT NOTICE: Please ensure care is taken with fixing locations when fitting an integrated handle door to an appliance. Under no circumstances should screws be used towards the top of the door for fixing, as this will damage the integrated handle section of the door as illustrated below. www.howdens.com 115
Appliance door applications Lamona - LAM8605 Door brackets should be located as per the instruction booklet supplied with the appliance. Use the screw fixing locations (shown below) in replacement for the ones shown in the instruction booklet. Remove the screw located in the second hole position from the top edge. Carefully drill through the hole using a 3.5mm bit. Back of the dishwasher door illustrated. LAM8605 2nd 2nd 4th 4th 116 www.howdens.com
Appliance door applications Lamona - LAM8603, LAM8303, LAM8302 Door brackets should be located as per the instruction booklet supplied with the appliance. Use the screw fixing locations (shown below) in replacement for the ones shown in the instruction booklet. Back of the dishwasher door illustrated. LAM8603/LAM8303 3rd 3rd 4th 4th Remove the screw located in the fifth hole position from the top edge. Carefully drill through the hole using a 3.5mm bit. LAM8302 Back of the dishwasher door illustrated. 3rd 3rd 5th 5th www.howdens.com 117
Appliance door applications NOTE: For all dishwasher applications, care must be taken when fixing the frontal to the appliance. Use the template supplied with the dishwasher for door fixing. IMPORTANT: Use the DRAWER LINE upper fixing positions. Using the hi-line fixing as shown on the template will damage the integrated handle section (see below). First Fixing Second Fixing Lamona - HJA6312, HJA6132, LAM6400 This information replaces the top bracket fixing information shown within the appliance booklets. Follow the appliance booklets for all other aspects of installation. Fix the top brackets to the door in the positions shown below. Once in place, fit the door to the appliance and secure using the screws provided. NOTE: Make sure the bracket is positioned the correct way up. When fitting the door to the appliance, additional washers can be used between the screw head and the bracket to secure. = 320mm = 65mm NOTE: Additional height adjustment for door alignment can be achieved by adjusting the appliance feet. 118 www.howdens.com
Curved base decor end and door fixing Assembly For fixing the legs to the cabinet, see page 16-17. 1 Fit battens (supplied with cabinet) to the decor panel. 49mm 16.5mm Screw x4 (30mm) 28mm 33mm Top rail only requires new drilling. 1 to 2mm gap 16.5mm 2 Curved base hinge pack required. Fit the hinge and plate to the door and decor panel. Hinge and plate x2 Screws x4 (13mm) 3 With the base cabinet laid flat, secure the decor panel and door using screws through the base and top shelf and into the battens. Screw x 4 (40mm) 1 to 2mm gap. www.howdens.com 119
120 www.howdens.com