Instruction Manual Popcorn Topping Dispenser Model Series 2396-00-100 (101, 110, 111, and 140) Pedestal Assembly for Models without Remote. Rack Assembly shown for Single Pedestal Models. 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA 2017 Gold Medal Products Co. Part No. 39140
SAFETY PRECAUTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment. 014_020416 WARNING To avoid burns, DO NOT touch heated surfaces. DO NOT place or leave objects in contact with heated surfaces. 009_092414 WARNING ALWAYS wear safety glasses when servicing this equipment. 010_010914 WARNING No user serviceable parts inside. Refer servicing to qualified service personnel. 011_051514 WARNING Read and understand operator s manual and all other safety instructions before using this equipment. To order copies of the operator s manual go to or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862 022_060215 Page 2
SAFETY PRECAUTIONS (continued) WARNING DO NOT allow direct contact of this equipment by the public when used in food service locations. Only personnel trained and experienced in the equipment operation may operate this equipment. Carefully read all instructions before operation. 012_010914 WARNING This machine is NOT to be operated by minors. 007_010914 Note: Improvements are always being made to Gold Medal s equipment. This information may not be the latest available for your purposes. It is critical that you call Gold Medal s Technical Service Department at 1-800-543-0862 for any questions about your machine operations, replacement parts, or any service questions. (Gold Medal Products Co. does not assume any liability for injury due to careless handling and/or reckless operation of this equipment.) General images may be used in manual for reference only. Page 3
INSTALLATION INSTRUCTIONS Inspection of Shipment After unpacking, check thoroughly for any damage which may have occurred in transit. Claims should be filed immediately with the transportation company. The warranty does not cover damage that occurs in transit, or damage caused by abuse, or consequential damage due to the operation of this machine, since it is beyond our control (reference warranty in back of manual). Manual Read and understand the operator s manual and all other safety instructions before using this equipment. To order copies of the operator s manual go to or write to Gold Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862. Model Description Model Series 2396 is a pedestal style topping dispenser with an LED lighted sign. Model includes an open rack assembly which will accept 2 boxes of topping. The pedestal(s) mounts to a counter top; the open rack is installed under the counter in an enclosed area for the heater to maintain product temperature (countertop and cabinet to be provided by customer). The forced air heating system controls the temperature of the cabinet to 120-130 F. The foil heater in the pedestal assures dispense temperature of 110-130 F. This series has no heated line capability. See below for individual model descriptions. 2396-00-100: Single Pedestal Topping Dispenser, with one open rack assembly. 2396-00-101: Single Pedestal Topping Dispenser, with one open rack assembly; unit features an ADA Remote Switch. 2396-00-110: Double Pedestal Topping Dispenser, with one open rack assembly which feeds both pedestals. 2396-00-111: Double Pedestal Topping Dispenser, with one open rack assembly which feeds both pedestals; unit features two ADA Remote Switches. 2396-00-140: Double Pedestal Topping Dispenser, with one open rack assembly which feeds both pedestals (has 5 ft. long tubing to pedestal). Items Included with this Unit Drip Pan Drip Pan Insert Items shown are included for each pedestal. (4) Washers for Pedestal Mounting (4) Wing Nuts for Pedestal Mounting Page 4
Setup This unit has been tested at the factory. 1. Remove all packaging and tape prior to installation. 2. The pedestal and rack assembly must be installed in a sturdy, level cabinet (provided by the customer). Follow all instructions in the Electrical Requirement and Unit Installation sections of this manual to complete installation of this unit. 3. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of this manual). Control Box 6 Prong Receptacle Power Cord Pedestal Power Cord Universal Bag Connector(s) (connects to the topping bag) Single pedestal model shown for general reference. Discharge Oil Line(s) (connects to the pedestal) Page 5
Electrical Requirements The following power supply must be provided: 2396-00-100, 2396-00-101: 120 V~, 324 W, 60 Hz 2396-00-110, 2396-00-111, 2396-00-140: 120 V~, 390 W, 60 Hz DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 A certified electrician must furnish sufficient power for proper machine operation and install any supplied receptacle. We recommend this equipment be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold Medal Products Co. s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset. Before You Plug In Machine 1. Make sure all machine switches are OFF before plugging equipment into receptacle. 2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power supply cord. 3. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary. 4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable). 5. Install unit in a level position. CAUTION If the supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent or similarly qualified persons in order to avoid a hazard. 039_080614 Page 6
Unit Installation Follow the instructions below to install the Topping Dispenser. 1. The bottom portion of the Topping Dispenser (the rack assembly) needs to be placed in an area under the counter that can be enclosed on all sides in order for the heater to properly maintain product temperature (cabinet to be provided by customer). Limit the width of the cabinet to 3 feet, to ensure adequate cabinet temperature. Access will be required to the front of this area allowing sufficient clearance to clean and maintain the pump, and to add or remove boxes of topping. 2. The countertop will require preparation by drilling the mounting holes for the pedestal, and by cutting the rectangular holes for the power cable and oil tube, drip pan, and remote switch (if equipped). See Countertop Cutout Dimensions on next page for reference. If your counter is thicker than the provided mounting studs attached to the pedestal, then counter bore the underside of the countertop to allow for the washers and wing nuts. 3. Set the pedestal onto the countertop and secure it in place with the wing nuts and washers provided. 4. Set the rack assembly into the opening under the counter. 5. Attach the heated discharge oil-line tubing from the base to the aluminum tube on the pedestal with the hose clamp provided (dual pedestal units will have 2 lines). 6. Plug the power cord from the pedestal(s) into the 6-prong receptacle on the side of the control box (located on top of the rack assembly). 7. Plug the power cord from the rack assembly into a proper outlet (see Electrical Requirements section). 8. If model is a dual pedestal unit, turn the power on and test the connections. Press the dispense button and check to see that the correct pump is running to feed product to the correct pedestal. If not, turn the power off and switch the six-prong plugs to the opposite receptacles. 9. The unit is now ready to load boxes of topping, see Topping Installation section. Page 7
.188 1.875" MIN 6.875" MAX 4.938.188 8.750 1.609 1.297 2.594 3.219 1.609 1.297 2.594 3.219 SPACED TO SUIT 8.750 1.609 1.297 2.594 3.219 Popcorn Topping Countertop Cutout Dimensions This section shows the placement, hole size and cutout dimensions to mount the pedestal(s), drip pan, and ADA Remote (if equipped). Single and Dual Pedestal 4.625 15.500 3.094 2.688 PEDESTAL MOUNTING DRIP PAN CUT-OUT n.375 THRU FOR 1/4-20 BOLTS(4) 3.094 2.688 PEDESTAL MOUNTING DRIP PAN CUT-OUT Models with ADA Remote Switch Dimensions for Single Pedestal Model with ADA Remote Switch shown; space accordingly for Dual Pedestal Models with ADA Remote Switches. EDGE OF COUNTER 3.219 4.625 DRIP PAN CUT-OUT 15.500 3.094 2.688 PEDESTAL MOUNTING n.375 THRU FOR 1/4-20 BOLTS(4) 2.688 ADA SWITCH CUT-OUT n.188(4) LOCATE FROM EDGE OF COUNTER TO MEET 48" ADA REACH LIMIT 1.594 CABLE CONNECTING REMOTE SWITCH TOPEDESTALIS20"LONG Page 8
Topping Installation Use maximum of (2) 35 pound boxes of topping for this unit. IMPORTANT: DO NOT attempt to operate this system with a bag which has been removed from the box. This product is not intended for use with volatile food products (i.e. real butter). 1. Load two boxes of pre-heated topping onto the rack. Gold Medal s Backroom Warmer (Item No. 2262) may be purchased for pre-heating the topping. Mount the box in the rack so the topping bag nozzle is located towards the bottom of the box to permit a free flow of the topping from the bag. 2. Remove the cardboard cutout on the box to expose the bag nozzle, and then remove the cap from the bag nozzle. 3. Attach the Universal Bag Connector (from the rack assembly) to the bag nozzle as shown below. Once oil is connected, the unit is ready for use. Steps to Attach the Universal Bag Connector Universal Bag Connector Bag Nozzle Step 1: Pull the Universal Bag Connector s plunger out until it clicks into the open position. Plunger OUT in open position Step 2: Grasp the Bag Nozzle and slide the Bag Connector on from the side. Step 3: With the hose connector in place, press plunger forward to lock. Step 4: Connector shown with plunger fully forward in lock position. Page 9
OPERATING INSTRUCTIONS Controls and Their Functions HEAT SWITCH Three position rocker switch. Center position is OFF. Up position is HEAT ONLY. This activates the display light, the heater/blower that will maintain cabinet temperature, and activates the foil heater in the pedestal. Down position is PUMP & HEAT. This activates the display light, the heater/blower, the foil heater in the pedestal, and provides power to the pump(s). PUSH BUTTON PUMP SWITCH There are two Push Button (PB) Pump Switches on a pedestal. One is located on the top of the pedestal and the other is at the base of the pedestal. Press and hold button to dispense butter flavored topping. Release button to stop dispensing topping. ADA REMOTE - PUSH BUTTON PUMP SWITCH (for Model 2396-00-101 and 111 Only) Press and hold the Remote PB Pump Switch to dispense butter flavored topping. Release button to stop dispensing topping. (Dual Pedestal Models have an ADA Remote Switch for each pedestal.) RED PILOT LIGHT Pilot Light located on the control box of the rack assembly. When lit, the red light signals the pump is active. (Dual Pedestal Models have a Pilot Light for each pedestal.) 1 AMP FUSE The 1 AMP Fuse protects the oil dispense unit from an overload condition. (Dual Pedestal Models have a fuse for each pump.) PB Pump Switch Red Pilot Light Heat Switch 1 AMP Fuse PB Pump Switch ADA Remote - PB Pump Switch (Models 2396-00-101 and 111 Only) Page 10
Operating the Topping Dispenser 1. To Pump and Heat Topping - Turn the Heat Switch (located on control box) to the PUMP & HEAT position to activate the display light, the heater/blower (to maintain cabinet temperature), the foil heater in the pedestal, and provide power to the pump(s). 2. To dispense topping - Press and hold either of the Red PB Pump Switches located on the pedestal (or remote, if equipped). If this is the first time the unit has been used, it may take a few seconds to completely fill the tube and dispense topping. 3. To use Heat Only -Turn the Heat Switch (located on control box) to the HEAT ONLY position to activate the display light, the heater/blower (to maintain cabinet temperature), and the foil heater in the pedestal. On the HEAT ONLY setting the pump is de-activated. Page 11
Care and Cleaning DANGER Machine must be properly grounded to prevent electrical shock to personnel. DO NOT immerse in water. DO NOT clean appliance with a water jet. Always unplug the equipment before cleaning or servicing. 025_111616 WARNING To avoid burns, DO NOT touch heated surfaces. DO NOT place or leave objects in contact with heated surfaces. 009_092414 Good sanitation practice demands that all food preparation equipment be cleaned regularly (only use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of advertising your product. Follow the directions below to clean and sanitize the unit each day after use. 1. Turn machine OFF, unplug the unit and allow it to cool before attempting to clean. 2. The exterior surfaces can be cleaned by wiping oil spills with a clean dry towel, then wipe with another clean towel dampened with mild soap and warm water. 3. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088). DO NOT use oven cleaners or abrasive materials as they will damage parts of machine. 4. Where applicable, drip pan/drip pan insert may be taken to the sink to clean with mild soap and warm water. Allow to dry, then reassembly. 5. Clean plastic panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No. 2588) is recommended. Ammonia cleaners will damage plastic panels. Use only non-ammonia cleaners, such as Gold Medal Watchdog Glass Cleaner (Item No. 2588). Sanitizing the Tubing and Pump Items Needed: (2) Empty Pails (1) Cleaning Bracket (Item No. 12594) Gold Medal Chlor-Tech Sanitizer (Item No. 1109) Measure Cup (for priming unit) 1. Make sure Topping Dispenser has cooled completely before attempting to clean. 2. Fill a clean, empty pail half-full with hot water and Gold Medal Chlor-Tech Sanitizer (reference instructions on sanitizer container for appropriate amount). Page 12
3. Disconnect Universal Bag Connector from topping bag, and connect it to cleaning bracket as shown below. Make sure the quick disconnect is engaged. Step 1: Step 2: Step 3: Plunger OUT in open position. Cleaning Bracket Slide Connector onto Bracket Push Plunger IN to lock onto bracket. Plunger ENGAGED on pin. 4. Place hose with cleaning bracket into pail of sanitizing solution. 5. Place an empty pail under dispensing spout to receive cleaning solution pumped through unit. 6. Use the Red PB Pump Switch (located on the pedestal, or remote, if equipped) to dispense solution until tubes are clean and free of topping. 7. When pumping is complete, discard dirty solution, clean the pail, and refill with clean hot water. 8. Remove hose with bracket from solution pail and place it in the hot water. 9. Place the empty pail under spout. 10. Use PB Switch to dispense hot water until tubes are clean and free of sanitizer. 11. When cleansing is complete, remove pail from dispenser. 12. Remove hose with bracket from hot water, disconnect bracket, and wipe hose and bag connector dry. 13. Reconnect dispenser to bag of topping. 14. Purge and prime the system hold a measuring cup (or medium sized container) under dispenser spout; press the PB Switch to dispense topping until all water has been expelled and tubes are primed with topping. After cleaning, always discard the topping dispensed in priming. 15. Sanitize cleaning items for next use. Page 13
MAINTENANCE INSTRUCTIONS DANGER Machine must be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury, or death. DO NOT immerse any part of this equipment in water. DO NOT use excessive water when cleaning. Keep cord and plug off the ground and away from moisture. Always unplug the equipment before cleaning or servicing. Make sure all machine switches are in the OFF position before plugging the equipment into the receptacle. 008_051514 DANGER Improper installation, adjustment, alteration, service, or maintenance can cause property damage, injury, or death. Any alterations to this equipment will void the warranty and may cause a dangerous condition. This appliance is not intended to be operated by means of an external timer or separate remote-control system. NEVER make alterations to this equipment. Read the Installation, Operating, and Maintenance Instructions thoroughly before installing, servicing, or operating this equipment. 014_020416 WARNING No user serviceable parts inside. Refer servicing to qualified service personnel. 011_051514 CAUTION THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE OPERATOR. 027_010914 Page 14
ORDERING SPARE PARTS 1. Identify the needed part by checking it against the photos, illustrations, and/or parts list. (General images may be used in manual for reference only.) 2. Use only approved replacement parts when servicing this unit. 3. When ordering, please include part number, part name, and quantity needed. 4. Please include your model number, serial number, and date of manufacture (located on the machine nameplate/data plate) with your order. 5. Address all parts orders to: Parts Department Gold Medal Products Co. 10700 Medallion Drive Cincinnati, Ohio 45241-4807 Or, place orders by phone or online: Phone: (800) 543-0862 (513) 769-7676 Fax: (800) 542-1496 (513) 769-8500 E-mail: info@ Web Page: Page 15
2396-00-100 Popcorn Topping Rack Assembly - Exterior View 1 2, 3 6 7, 8 9, 10 4 11 5 12, 13, 14 See Tubing and Connectors Section 18, 19 17 16 15* *CAUTION: If supply cord is damaged, it must be replaced by Gold Medal Products Co., its service agent, or similarly qualified persons in order to avoid a hazard. Single Pedestal Rack Assembly shown for reference Part Number Item Part Description 2396-00-100 2396-00-101 2396-00-140 2396-00-110 2396-00-111 COMPLETE RACK ASSEMBLY 77461 1 CONTROL BOX 79375 79375 79375 2 CONTROL BOX COVER 79377 79377 79377 3 8-32 X 3/8 SLT. HWH M/S (screws to hold cover) 42044 42044 42044 4 B.I.B. BUTTER PUMP 79888 79888 79888 5 RETAINING STRAP 38998 38998 38998 6 RED PILOT LIGHT 41033 41033 41033 7 3 POSITION ROCKER SWITCH 39410 39410 39410 8 SWITCH LABEL 39413 39413 39413 9 FUSE HOLDER 74636 74636 74636 10 1 AMP FUSE 79341 79341 79341 11 SOCKET ASSEMBLY 100299 100299 100299 12 6-32 X 3/8 PHIL PAN M/S (fastens socket assy.) 39000 39000 39000 13 #6 INT. TOOTH L/W 410SS (fastens socket assy.) 39001 39001 39001 14 6-32 M/S NUT 18-8 (fastens socket assy.) 14221 14221 14221 15* LEAD-IN CORD 15 AMP PLUG 22038 22038 22038 16 R 31-2 STRAIN RELIEF 41735 41735 41735 17 HEAT DEFLECTOR 38995 38995 38995 18 8-32 X 1/4 HX HD WHIZLOCK 42045 42045 42045 19 ACORN NUT #8-32 47702 47702 47702 Page 16
Tubing and Connectors 1 1 2 3 4 5 Item Part Description Part Number 1 FOOD TUBING (replacement tubing is sold by the foot) 91375 2 SINGLE WIRE HOSE CLAMP 75110 3 UNIVERSAL BAG CONNECTOR 79100G 4 IN LINE STRAINER 79269 5 HOSE CLAMP 67843 Page 17
Rack Assembly - Control Box Interior Parts Breakdown 1 2 3 4, 5, 6 7 8 9 10 11, 12 13 14 15 16 General image of dual pedestal model shown for reference. Page 18
Rack Assembly - Control Box Interior Parts List Item Part Description Part Number All Models 1 120 VOLT 60 CY BLOWER 48018 2 250 WATT 120 VOLT HEAT ELEMENT 38824 3 EXHAUST BLOWER PLUG AND CORD 47199 4 8-32 X 2 PH PAN M/S 18-8 39012 5 #8 INT. TOOTH L/W 410SS 12132 6 HEX NUT #8-32 STAINLESS 89129 7 B.I.B. BUTTER PUMP 79888 8 PILOT LIGHT-125V RED 41033 9 3 POSITION ROCKER SWITCH 39410 10 150 OHM RESISTOR AND DIODE ASSY 55443 11 6-32 X 3/8 PHIL PAN M/S 39000 12 6-32 M/S NUT 18-8 14221 13 THERMOSTAT 135F 38990 14 FUSE HOLDER 74636 15 1 AMP FUSE 79341 16 SOCKET ASSEMBLY 100299 Page 19
2396-00-100 Popcorn Topping Pedestal Exterior Parts Breakdown 1 Light Cover Assembly 2 3 4 5 6 7 15 8 16 9 10 Model 2396-00-100 Front View 11 12 13 Model 2396-00-100 Rear View 14 19 7 20 17 18 16 21 22 Pedestal and Remote Switch View (Models 2396-00-101 and 111 Only) Page 20
Pedestal Exterior Parts List Item 1 Part Description 2396-00-100 2396-00-110 2396-00-140 COMPLETE PEDESTAL 77460 LIGHT COVER ASSEMBLY (includes 2 screws, butter bracket, light cover) Part Number 2396-00-101 2396-00-111 103160 103160 2 SCREW #8 HEX WASHER HEAD 47771 47771 3 BUTTER BRACKET 103158 103158 4 LIGHT COVER 103159 103159 5 END CAP 69202 69202 6 PUSH DECAL 103081 103081 7 MOMENTARY SWITCH 38971 38971 8 NO DRIP SPOUT 38566 38566 9 DISPENSER LABEL 39142 39142 10 STRAIGHT CORD GRIP 55234 55234 11 SR 31-2 STRAIN RELIEF 41735 41735 12 PLUG WIRE HARNESS 100301 100301 13 FLAT WASHER 1/4 STAINLESS 87261 87261 14 1/4-20 ST STL WING NUT 12466 12466 15 PEDESTIAL BACK PLATE 38872 38872 16 SCREW #8-32X3/8 PAN HD PH 74141 74141 17 MOLDED RECEPTACLE 41712 18 REMOTE SWITCH ASSEMBLY (complete assy.) 39154 19 DECAL 39181 20 SWITCH BOX 39152 21 SWITCH BOX BASE 39153 22 MOLDED PLUG 47726 Page 21
Top Pedestal Interior View Power Supply is located on back of Support Plate. 1 2 3 4 5 8 LED Support Plate 6, 7 9 10 11 12, 13 View under LED Support Plate Item Part Description Part Number All Models 1 61W LED STRIP 55379 2 SCREW #8 HEX WASHER HEAD 47771 3 LED SUPPORT PLATE 2499 69167 4 TOP PEDISTAL PLATE 2499 69168 5 POWER SUPPLY 24VDC 20W 55394 6 6-32 X 1/2 SL PAN HD M/S 47516 7 6-32 HEX NUT ZINC PLATED 38005 8 BUSHING, SNAP.875 IN 45396 9 MOMENTARY SWITCH 38971 10 NO DRIP SPOUT 38566 11 1/2 FLAT WASHER, S.S. 12627 12 SPOUT (Aluminum Dispense Tube) 103082 13 FOIL HEAT ELEMENT 8W 120V 38970 Page 22
Safety Labels 4 1 2 3 5 6 Unit Labels Power Cord Label 7 Item Part Description Part Number All Models 1 HOSE CONNECT LABEL 79388 2 WARNING LABEL MAX FUSE 1A 79343 3 LBL CAUTION DISCONNECT PR 87149 4 SERVICE LABEL 87935 5 LBL WARN DISCONNECT POWER 74119 6 LABEL SAFE OPERATING INST 47010 7 WARNING LABEL CORD 68720 Accessories 1 2 Item Part Description Part Number All Models 1 DRIP PAN 69148 2 PAN INSERT WELDMENT 69201 Page 23
All Models Wiring Diagram Page 24
WARRANTY WARRANTY + Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to be free of defects in workmanship and material under normal use and service. Gold Medal Products Co. s obligation under this warranty is limited solely to repairing or replacing parts, f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point. Except for Perishable Parts on specific machines, the above warranty applies for a period of two (2) years from the date of original sale to the original purchaser of equipment when recommended operating instructions and maintenance procedures have been followed. These are packed with the machine. Parts warranty is two (2) years, labor is six (6) months. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or consequential damages. No claim under this warranty will be honored if the equipment covered has been misused, neglected, damaged in transit, or has been tampered with or changed in any way. No claim under this warranty shall be honored in the event that components in the unit at the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty is effective only when electrical items have been properly attached to city utility lines only at proper voltages. This warranty is not transferable without the written consent of Gold Medal Products Co. The term Original Purchaser as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO., or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. 10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA Phone: (800) 543-0862 Fax: (800) 542-1496 (513) 769-7676 (513) 769-8500 2017 The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website display, without its express written consent. Page 25