WATERSIDE BUILDING GROUP E4

THE INSTALLING CONTRACTOR: ELITE FIRE PROTECTION, INC. 4020 WEST CHESTER PIKE NEWTOWN SQUARE, PA 19073 PHONE #: 1-610 325-3556 FAX #: 1-484 422-8517 www.elitefireprotection.us Sprinkler Equipment Submittal FOR WATERSIDE BUILDING GROUP E4 BENSALM, PA FIRE PROTECTION SYSTEM

September 18, 2009 30a easypac commercial riser manifold assemblies 1-1/4-8 (DN32 - DN200) Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 1. DESCRIPTION Viking EasyPac Commercial Riser Manifold Assemblies are available in sizes 1-1/4, 1-1/2, 2, 2-1/2, 3, 4, 6 and 8 for commercial systems. They are available with an AGF TESTanDRAIN valve, and/or pressure relief valve (PRV) to meet NFPA 13 requirements for gridded systems and any system requiring a pressure relief valve. This configuration eliminates the need to drain the system before installing the relief valve, while a built in test port allows hydrostatic testing without draining the system. EasyPac Commercial Assemblies are designed with all required equipment and standard components that can be replaced in the field, including pressure gauges, Potter flow switches, 3-way gauge control valve and appropriate drain valve. All assemblies are available in grooved inlet and outlet connections 1-1/4-8 using Schedule 10 steel pipe. The 1-1/4 to 2 assemblies are also available with male NPT threaded inlets and outlets, or threaded inlets x grooved outlets using Schedule 40 steel pipe. 2. LISTINGS AND APPROVALS Pressure Gauges: UL Listed, FM Approved Waterflow Alarm Switch: UL Listed - Category USQT, cul Listed, FM Approved - Waterflow Detectors, Vane Type, CSFM Listed Ball Valve: UL Listed, FM Approved AGF TestanDrain Model 1000: UL Listed - Category VEHZ, FM Approved - Sprinkler System Alarm Testers AGF TestanDrain Model 1011 with Pressure Relief Valve: UL Listed - Category VEHZ, FM Approved - Sprinkler System Alarm Testers 3. Technical data Specifications and Material Standards: Available since 2007. Pressure Rating: 250 PSI (17.2 bar) maximum water working pressure. Fabricated steel pipe. Available in grooved inlet and outlet connections 1-1/4 to 8 using Schedule 10 steel pipe. 1-1/4, 1-1/2, and 2 assemblies are also available with male NPT threaded inlet and outlet, or threaded inlet x grooved outlet using Schedule 40 steel pipe. Riser bodies coated with black Ecoat. Flow Switch: Two single-pole double-throw switches with Form C contacts rated at 15 Amps 125/250 V. AC, 2.5 Amp 0-30 V. DC. Each switch can be wired for open or closed circuit operation. See Figure 1. Ordering Information: (Also refer to the current Viking price list.) There are three different options are available for the commercial line: Commercial EasyPac Assemblies with Ball Valve (See figure 2) Commercial EasyPac Assemblies with TESTanDRAIN Valve (See figure 3) Commercial EasyPac Assemblies with TESTanDRAIN and Pressure Relief Valve (PRV) (See figure 4) See Table 1 for Part Numbers. 4. Installation Refer to appropriate NFPA Installation Standards. Note: EasyPac Commercial Riser Manifold Assemblies can be installed horizontally with flow switch on top, or vertically with flow upward. Viking EasyPac Riser Assemblies use Potter VSR flow switches. The literature that accompanies the VSR states that the switch should not be installed within 6 of a change of direction of pipe or within 24 of a valve. This is merely a recommendation to reduce the possibility of the switch not operating while minimal waterflow is occurring. This is a recommendation only, not a requirement. 5. Operating Instructions 1. To Test: Turn valve handle counterclockwise from Off to Test. The handle will stop automatically. After test is completed, return handle to Off. 2. To Drain: Turn handle counterclockwise from Off to Test. The handle will stop automatically. Depress Push button and turn handle to Drain. When system is empty, return handle clockwise to Off position. 6. Inspections, tests and maintenance Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. Viking Technical Data may be found on The Viking Corporation s Web site at http://www.vikinggroupinc.com. The Web site may include a more recent edition of this Technical Data Page. Form No. F_102307 Replaces page 30a-f dated July 31, 2009. (Removed note regarding the flow switch for Canada orders-now use the same flow switch.)

30b September 18, 2009 easypac commercial riser manifold assemblies 1-1/4-8 (DN32 - DN200) Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Table 1 - Commercial EasyPac Assemblies Pipe Size Inlet / Outlet Viking Part Option Pipe Size Connections Number Ball Valve 15248 Thread / Thread TESTanDRAIN Schedule 40 14871 TESTanDRAIN and PRV 14873 Ball Valve 15249 1-1/4 Groove / Groove TESTanDRAIN Schedule 10 14872 TESTanDRAIN and PRV 14874 Ball Valve 15250 Thread / Groove TESTanDRAIN Schedule 40 15251 TESTanDRAIN and PRV 15252 Ball Valve 15253 Thread / Thread TESTanDRAIN Schedule 40 14875 TESTanDRAIN and PRV 14877 Ball Valve 15254 1-1/2 Groove / Groove TESTanDRAIN Schedule 10 14876 TESTanDRAIN and PRV 14878 Ball Valve 15255 Thread / Groove TESTanDRAIN Schedule 40 15256 TESTanDRAIN and PRV 15257 Ball Valve 14899 Thread / Thread TESTanDRAIN Schedule 40 14935 TESTanDRAIN and PRV 14847 Ball Valve 14848 2 Groove / Groove TESTanDRAIN Schedule 10 14850 TESTanDRAIN and PRV 14851 Ball Valve 15258 Thread / Groove TESTanDRAIN Schedule 40 15259 TESTanDRAIN and PRV 15260 Ball Valve 14852 2-1/2 Groove / Groove TESTanDRAIN Schedule 10 14853 TESTanDRAIN and PRV 14854 Ball Valve 14855 3 Groove / Groove TESTanDRAIN Schedule 10 14856 TESTanDRAIN and PRV 14857 Ball Valve 14858 4 Groove / Groove TESTanDRAIN Schedule 10 14859 TESTanDRAIN and PRV 14860 Ball Valve 14861 6 Groove / Groove TESTanDRAIN Schedule 10 14862 TESTanDRAIN and PRV 14863 Ball Valve 15264 8 Groove / Groove TESTanDRAIN Schedule 10 15265 TESTanDRAIN and PRV 15266 TESTanDRAIN Option: Includes a test orifice with size specified from 3/8 (K2.8) to 25K ESFR*, depending on the smallest sprinkler installed on the system. Must add suffix to the part number for the desired orifice size. Orifice Suffix: A = 3/8 (K 2.8) B = 7/16 (K 4.2) C = 1/2 (K 5.6) D = 17/32 (K 8.0) E = K 11.2 ELO F = K14 ESFR G = K25 ESFR TESTanDRAIN with PRV Option: Includes test orifice and pressure relief valve. The test orifice must be specified based on the smallest sprinkler installed on the system for 3/8 (K2.8) to K25 ESFR*. The pressure relief valve is not factory assembled to the TestanDrain. Must add suffix to the part number for the desired orifice size and pressure setting of the pressure relief valve. Orifice Suffix: A = 3/8 (K 2.8) B = 7/16 (K 4.2) C = 1/2 (K 5.6) D = 17/32 (K 8.0) E = K 11.2 ELO F = K14 ESFR G = K25 ESFR PRV Suffix: 175 185 195 205 225 250 NOTE: It is important to note that the pressure rating of the relief valve indicates an operating range of pressure for both opening and closing of the valve. Standard relief valves are required to OPEN in a range of pressure between 90% and 105% of their rating. The valves are required to CLOSE at a pressure above 80% of that rating. * ESFR TESTanDRAIN not available in 1-1/4, 1-1/2 or 2 Risers. Pipe OD 1.660 (42 mm) Schedule 10 Pipe ID 1.45 (36.6 mm) Schedule 40 Pipe ID 1.38 (35.1 mm) Table 2 - Pipe Diameters 1-1/4 1-1/2 2 2-1/2 3 4 6 8 1.900 (48 mm) 1.69 (42.7 mm) 1.61 (40.9 mm) 2.375 (60 mm) 2.16 (54.8 mm) 2.07 (52.5 mm) 2.875 (73 mm) 2.64 (66.9 mm) 3.5 (89 mm) 3.26 (82.8 mm) 4.5 (114 mm) 4.26 (108.2 mm) 6.625 (168 mm) 6.36 (161.5 mm) 8.625 (219 mm) 8.249 (209.5 mm) N/A N/A N/A N/A N/A

September 18, 2009 30c easypac commercial riser manifold assemblies 1-1/4-8 (DN32 - DN200) Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 7. Availability The Viking EasyPac Riser Assemblies are available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. 8. Guarantee For details of warranty, refer to Viking s current list price schedule or contact Viking directly. Figure 1 - Flow Switch with Two Single Pole, Double Throw Micro Switches

30d September 18, 2009 easypac commercial riser manifold assemblies 1-1/4-8 (DN32 - DN200) Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 2 - Basic Commercial EasyPac Size A B C D E F G H I 1-1/4 (DN32) VSR-S Flow Switch 1 NPT 1-1/2 (DN40) VSR-S Flow Switch 1 NPT 2 (DN50) VSR Flow Switch 1 NPT 2-1/2 (DN65) VSR Flow Switch 1-1/4 NPT 3 (DN80) VSR Flow Switch 1-1/4 NPT 4 (DN100) VSR Flow Switch 2 NPT 6 (DN150) VSR Flow Switch 2 NPT 8 (DN200) VSR Flow Switch 2 NPT 16-1/2 (419) 16-1/2 (419) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-3/4 (375) 15 (381) 15 (381) 1-1/2 (38) 1-1/2 (38) -15/32 (12)* 5/8 (16) 5/8 (16) -1-3/4 (-44)* -1-3/4 (-44)* -1-3/4 (-44)* * Dimension E is negative because the ball valve extends below the end of the manifold body. 6-3/32 (155) 7-19/32 (193) 6-7/16 (164) 6-11/16 (170) 7 (178) 7-1/2 (191) 8-35/64 (217) 9-1/2 (243) 6-11/32 (161) 6-15/16 (164) 5-51/64 (148 ) 6-3/64 (154) 6-23/64 (162) 6-25/32 (173) 7-53/64 (199) 8-3/4 (225) 4-3/16 (107) 5-11/16 (144) 4-9/16 (116) 5-1/4 (133) 5-9/16 (141) 7-3/4 (197) 8-51/64 (223) 9-3/4 (249) 8-9/16 (218) 10-1/16 (256) 8-59/64 (227) 9-39/64 (244) 9-59/64 (252) 13-5/16 (338) 14-23/64 (365) 15-1/2 (391)

September 18, 2009 30e easypac commercial riser manifold assemblies 1-1/4-8 (DN32 - DN200) Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 3 - Commercial EasyPac with TESTanDRAIN Size A B C D E F G H I 1-1/4 (DN32) VSR-S Flow Switch 1 NPT 1-1/2 (DN40) VSR-S Flow Switch 1 NPT 2 (DN50) VSR Flow Switch 1 NPT 2-1/2 (DN65) VSR Flow Switch 1-1/4 NPT 3 (DN80) VSR Flow Switch 1-1/4 NPT 4 (DN100) VSR Flow Switch 2 NPT 6 (DN150) VSR Flow Switch 2 NPT 8 (DN200) VSR Flow Switch 2 NPT 16-1/2 (419) 16-1/2 (419) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-3/4 (375) 15 (381) 15 (381) 5-1/8 (131) 5-1/8 (131) 3-1/16 (78) 3-1/4 (83) 3-1/4 (83) 2-5/8 (66) 2-5/8 (66) 2-3/4 (70) 6-3/32 (155) 7-19/32 (193) 6-7/16 (164) 6-11/16 (170) 7 (178) 7-1/2 (191) 8-35/64 (217) 9-1/2 (243) 6-11/32 (161) 6-15/16 (164) 5-51/64 (148 ) 6-3/64 (154) 6-23/64 (162) 6-25/32 (173) 7-53/64 (199) 8-3/4 (225) 4-1/2 (114) 4-3/4 (121) 4-49/64 (121) 6-1/4 (159) 5-5/8 (143) 8-3/16 (208) 9-15/64 (235) 10-1/4 (262) 9-3/32 (231) 9-7/32 (234) 9-35/64 (242) 10-61/64 (278) 11-17/64 (286) 16-3/8 (416) 17-27/64 (443) 18-1/2 (468)

30f September 18, 2009 easypac commercial riser manifold assemblies 1-1/4-8 (DN32 - DN200) Telephone: 269-945-9501 Technical Services 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 4 - Commercial EasyPac with TESTanDRAIN and PRV Size A B C D E F G H I 1-1/4 (DN32) VSR-S Flow Switch 1 NPT 1-1/2 (DN40) VSR-S Flow Switch 1 NPT 2 (DN50) VSR Flow Switch 1 NPT 2-1/2 (DN65) VSR Flow Switch 1-1/4 NPT 3 (DN80) VSR Flow Switch 1-1/4 NPT 4 (DN100) VSR Flow Switch 2 NPT 6 (DN150) VSR Flow Switch 2 NPT 8 (DN200) VSR Flow Switch 2 NPT 16-1/2 (419) 16-1/2 (419) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-1/2 (369) 14-3/4 (375) 15 (381) 15 (381) 5-1/8 (131) 5-1/8 (131) 3-3/16 (81) 3-1/4 (83) 3-1/4 (83) 2-5/8 (66) 2-5/8 (66) 2-3/4 (70) 6-3/32 (155) 7-19/32 (193) 6-7/16 (164) 6-11/16 (170) 7 (178) 7-1/2 (191) 8-35/64 (217) 9-1/2 (243) 6-11/32 (161) 6-15/16 (164) 5-51/64 (148 ) 6-3/64 (154) 6-23/64 (162) 6-25/32 (173) 7-53/64 (199) 8-3/4 (225) 4-1/2 (114) 4-3/4 (121) 5-13/64 (132) 6-1/4 (159) 5-5/8 (143) 8-3/16 (208) 9-15/64 (235) 10-1/4 (262) 9-3/32 (231) 9-7/32 (234) 10-45/64 (272) 10-61/64 (278) 11-17/64 (286) 16-3/8 (416) 17-27/64 (443) 18-1/2 (468) Form No. F_102307 Replaces page 30a-f dated July 31, 2009. (Removed note regarding the flow switch for Canada orders-now use the same flow switch.)

Features Sizes Available (Nominal): 3/4 (DN20) through 3 (DN80) pipe diameters, with a Standard Dimension Ratio (SDR) of 13.5 as specified in ASTM F442. Environmental Specifications: Indoor use only. Maximum Ambient Temperature: 150 F (65 C) Hazen-Williams C Value: 150 Pressure Data: Working Pressure: 175 PSI (12.1 bar) at 150 F (65 C) Specifications: Meets NFPA 13R and 13D standards for residential occupancies as well as NFPA 13 standards for light hazard occupancies. Pipe meets or exceeds ASTM F442. Certified by NSF International for potable water services. CPVC pipe from Viking Plastics use compound cell class 23547 (demonstrated highest structural properties). culus Listed, FM Approved, New York City (MEA) Approved, LPCB Approved. CPVC PIPE PHYSICAL DATA Nominal Pipe Size Actual Outside Diameter Average Inside Diameter *Weight per 15 (4,6 m) length Length Inch DN Inch mm Inch mm Lb. Kg. Feet M 3/4 DN20 1.050 26,670 0.874 22,199 2.52 1,14 15 4.6 Approvals Part Number 34PIPE 1 DN25 1.315 33,401 1.101 27,965 3.93 1,78 15 4.6 1PIPE 1 1/4 DN32 1.660 42,164 1.394 35,408 6.27 2,84 15 4.6 114PIPE 1 1/2 DN40 1.900 48,260 1.598 40,589 8.22 3,73 15 4.6 culus, FM, 112PIPE NSF 2 DN50 2.375 60,325 2.003 50,876 12.89 5,85 15 4.6 2PIPE 2 1/2 DN65 2.875 73,000 2.423 61,500 18.86 8,55 15 4.6 212PIPE 3 DN80 3.500 88,900 2.950 74,900 28.01 12,71 15 4.6 3PIPE Nominal Pipe Size Actual Outside Diameter Average Inside Diameter *Weight per 10 (3,05 m) length Length Inch DN Inch mm Inch mm Lb. Kg. Feet M 3/4 DN20 1.050 26,670 0.874 22,199 1.68 0,76 10 3,05 Approvals Part Number 34PIPE10 1 DN25 1.315 33,401 1.101 27,965 2.62 1,19 10 3,05 1PIPE10 1 1/4 DN32 1.660 42,164 1.394 35,408 4.18 1,90 10 3,05 114PIPE10 1 1/2 DN40 1.900 48,260 1.598 40,589 5.48 2,49 10 3,05 culus, FM, 112PIPE10 NSF 2 DN50 2.375 60,325 2.003 50,876 8.59 3,90 10 3,05 2PIPE10 2 1/2 DN65 2.875 73,000 2.423 61,500 12.57 5,70 10 3,05 212PIPE10 3 DN80 3.500 88,900 2.950 74,900 18.67 8,47 10 3,05 3PIPE10 NOTE: CPVC Pipe is produced in SDR 13.5 Dimensions in accordance with ASTM F442. Standard Dimension Ratio is the ratio of the outside pipe diameter to the wall thickness of the pipe. Blazemaster is a registered trademark of Lubrizol. Specifications subject to change without notice *Empty pipe weights IMPORTANT: Installers should receive thorough hands-on training in the proper methods of assembly and installation of CPVC products. Trusted above all

CPVC Pipe Product Specifications Corrosion resistant CPVC fire sprinkler pipe, when installed in strict accordance with the manufacturer s design and installation instructions, is UL and c-ul Listed by Underwriters Laboratories for use in the following: Meets NFPA 13R and 13D standards for residential occupancies as well as NFPA 13 standards for light hazard occupancies. Residential occupancies up to and including four stories in height as defined by NFPA 13R. Residential occupancies as defined in the Standard for Sprinkler Systems in One and Two Family Dwellings, NFPA 13D. Installation of private fire service mains and their appurtenances, NFPA 24. CPVC fire sprinkler pipe from Viking Plastics shall be employed in wet pipe systems only and are not listed for outdoor use. CPVC pipe must never be used in a system using compressed air or other gases. CPVC pipe from Viking Plastics also carries the following enhanced listings and approvals: According to UL Listing Can be flush at return air plenums Exposed system risers NFPA 13D, 13R Exposed basement NFPA 13D (solid wood joist) Extended coverage (exposed) 20 spacing on pendent in lieu of 15 18 spacing on sidewall in lieu of 14 Use with combustible concealed sprinklers Tyco attic sprinkler head (to protect the floor below) Tyco attic sprinkler head with wet system piping (feed main and ridge installation) Exposed sidewall sprinkler listing for exposed pipe & fittings 24 extended coverage sidewall sprinkler, 12 drop, 155 F sprinkler head 18 extended coverage sidewall sprinkler, 12 drop, 165 F sprinkler head 16 extended coverage sidewall sprinkler, 12 drop, 175 F sprinkler head 14 standard coverage sidewall sprinkler, 12 drop, 200 F sprinkler head Factory Mutual Approved* Factory Mutual Approval exposed Factory Mutual Approval above drop-in ceilings Factory Mutual Approval exposed w/soffi-steel soffiting covering system New and enhanced listings and approvals are being pursued. Always check with the appropriate Listing and Approval agency for details on current listing parameters. CPVC pipe meets all applicable standards for pressure rated application as required in ANSI-NSF Standard 14 and complies with ANSI-NSF Standard 61 for health effects and are marked with the NSF-pw end use marking. All CPVC fire sprinkler pipe shall be Listed by Underwriters Laboratories for wet pipe systems, and shall carry a rated working pressure of 175 psi @ 150 F (12 bar @ 65.5 C). *The FM Approval is limited to use in wet pipe fire protection sprinkler systems for light hazard occupancies in both concealed and exposed applications with certain restrictions. Piping must always be installed in strict accordance to the manufacturer s DESIGN AND INSTALLATION GUIDE, including product storage and handling, joining methods, supporting and bracing, expansion and contraction allowance and testing, etc. National Fire Protection Association (NFPA) Standards 13, 13D, and 13R must be referenced for design and installation requirements in conjunction with the installation instructions. All CPVC fire sprinkler pipe from Viking Plastics is manufactured in the USA. All CPVC pipe shall be packaged immediately after its manufacture to prevent damage and shall be stored indoors after production, at the manufacturing site, until shipped from the factory. The pipe shall bear the logo of the listing agencies, and shall carry the National Sanitation Foundation (NSF) seal of approval for potable water applications. CPVC products are intended for use in areas where the maximum ambient temperature does not exceed 150 F (65.5 C). If the ambient temperature is expected to exceed this limitation, refer to the manufacturer s DE- SIGN AND INSTALLATION GUIDE for additional information on methods to reduce the pipe exposure temperatures. CPVC pipe is not intended to be installed in outdoor applications. CPVC pipe is intended to be used in wet pipe systems only and have not been investigated for use in dry pipe systems. Special installation and design criteria relative to pipe hanger spacings, piping and sprinkler restraint, sprinkler temperature rating, piping locations, testing procedures and friction loss characteristics are specified in the manufacturer s installation instructions provided with the pipe. The manufacturer s installation instructions should be reviewed and the Authority Having Jurisdiction consulted before installation. Trusted above all

January 13, 2012 Sprinkler 149m freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 1. DESCRIPTION Viking Freedom Residential Pendent Sprinkler VK468 is a small, thermosensitive, glassbulb residential sprinkler available in several different finishes and temperature ratings to meet varying design requirements. The orifice design, with a K-Factor of 4.9 (70.6 metric ), allows efficient use of available water supplies for the hydraulically designed fire-protection system. The glass bulb operating element and special deflector characteristics meet the challenges of residential sprinkler standards. 2. LISTINGS AND APPROVALS culus Listed: Category VKKW NYC Approved: MEA 89-92-E, Volume 35 NSF Certified: NSF/ANSI Standard 61, Drinking Water System Components Refer to the Approval Chart on page 149o and Design Criteria on page 149r for culus Listing requirements that must be followed. 3. technical data Specifications: Available since 2006. Minimum Operating Pressure: Refer to the Approval Chart. Maximum Working Pressure: 175 psi (12 bar). Factory tested hydrostatically to 500 psi (34.5 bar). Thread size: 1/2 (15 mm) NPT Nominal K-Factor: 4.9 U.S. (70.6 metric ) Metric K-factor measurement shown is in Bar. When pressure is measured in kpa, divide the metric K-factor shown by 10.0. Glass-bulb fluid temperature rated to -65 F (-55 C) Overall Length: 2-1/4 (58 mm) Material Standards: Frame Casting: Brass UNS-C84400 or QM Brass Deflector: Brass UNS-C23000, Phosphor Bronze UNS-C51000, or Brass UNS-C26000 Bulb: Glass, nominal 3 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with Teflon Tape Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel UNS-S30400 Compression Screw: Brass UNS-C36000 Ordering Information: (Also refer to the current Viking price list.) Sprinkler: Base Part No. 13637 Viking Technical Data may be found on The Viking Corporation s Web site at http://www.vikinggroupinc.com. The Web site may include a more recent edition of this Technical Data Page. Order Sprinkler VK468 by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A, Chrome-Enloy = F, and White Polyester = M-/W Temperature Suffix: 155 F (68 C) = B, 175 F (79 C) = D For example, sprinkler VK468 with a Brass finish and a 155 F (68 C) temperature rating = Part No. 13637AB. Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the Sprinkler Accessories section of the Viking data book.) Sprinkler Wrenches: A. Standard Wrench: Part No. 10896W/B (available since 2000) B. Wrench for recessed sprinklers: Part No. 13577W/B* (available since 2006) C. Optional Protective Sprinkler Cap Remover/Escutcheon Installer Tool** Part No. 15915 (available since 2010.) *A ½ ratchet is required (not available from Viking). **Allows use from the floor by attaching a length of 1 diameter CPVC tubing to the tool. Ideal for sprinkler cabinets. Refer to Bulletin F_051808. Form No. F_012706 Replaces page 149m-t, dated March 18, 2011. (Revised sprinkler materials and added reference to TIA 1028R.)

Sprinkler 149n January 13, 2012 freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Sprinkler Cabinets: A. Six-head capacity: Part No. 01724A (available since 1971) B. Twelve-head capacity: Part No. 01725A (available since 1971) 4. Installation Refer to appropriate NFPA Installation Standards. For NFPA 13D horizontal ceiling criteria and slopes, refer to TIA 1028R for slope ceiling criteria exceptions. 5. Operation During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the pip cap and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. 6. inspections, tests and maintenance Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. 7. availability The Viking Model VK468 Sprinkler is available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. 8. Guarantee For details of warranty, refer to Viking s current list price schedule or contact Viking directly. Sprinkler Temperature Classification TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Nominal Temperature Rating 1 Maximum Ambient Ceiling Temperature 2 Bulb Color Ordinary 155 F (68 C) 100 F (38 C) Red Intermediate 175 F (79 C) 150 F (65 C) Yellow Sprinkler Finishes: Brass, Chrome-Enloy (patents pending), and White Polyester 1 The sprinkler temperature rating is stamped on the deflector. Footnotes 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. Figure 1: Standard Sprinkler Wrench 10896W/B

January 13, 2012 Sprinkler 149o freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Sprinkler Base Part Number 1 SIN Approval Chart Residential Pendent Sprinkler VK468 For systems designed to NFPA 13D 10 or NFPA 13R. For systems designed to NFPA 13, refer to the design criteria on page 149r. NPT Thread Size Nominal K-Factor Maximum Water Overall Length Inches mm U.S. metric 2 Working Pressure Inches mm 13637 VK468 1/2 15 4.9 70.6 175 psi (12 bar) 2-1/4 58 Maximum Areas of Coverage 4 Minimum Water Supply Requirements 4 (Refer also to Design Criteria on page 149r.) Listings and Approvals 3 culus 5 NYC 6 NSF 8 Installed below smooth, flat, horizontal ceilings, including ceilings with slopes up to and including 2/12 (9.5 ). 12 ft. x 12 ft. (3.7 m x 3.7 m) 13 gpm @ 7.0 psi (49.2 L/min @ 0.48 bar) A1X A1X A1X 14 ft. x 14 ft. (4.3 m x 4.3 m) 13 gpm @ 7.0 psi (49.2 L/min @ 0.48 bar) A1X A1X A1X 16 ft. x 16 ft. (4.9 m x 4.9 m) 13 gpm @ 7.0 psi (49.2 L/min @ 0.48 bar) A1X A1X A1X 18 ft. x 18 ft. (5.5 m x 5.5 m) 17 gpm @ 12.0 psi (64.4 L/min @ 0.83 bar) A1X A1X A1X 20 ft. x 20 ft. (6.1 m x 6.1 m) 20 gpm @ 16.7 psi (75.7 L/min @ 1.15 bar) A1X A1X A1X Installed below horizontal ceilings with beams 9. 12 ft. x 12 ft. (3.7 m x 3.7 m) 13 gpm @ 7.0 psi (49.2 L/min @ 0.48 bar) B1X B1X B1X 14 ft. x 14 ft. (4.3 m x 4.3 m) 13 gpm @ 7.0 psi (49.2 L/min @ 0.48 bar) B1X B1X B1X 16 ft. x 16 ft. (4.9 m x 4.9 m) 13 gpm @ 7.0 psi (49.2 L/min @ 0.48 bar) B1X B1X B1X 18 ft. x 18 ft. (5.5 m x 5.5 m) 17 gpm @ 12.0 psi (64.4 L/min @ 0.83 bar) B1X B1X B1X 20 ft. x 20 ft. (6.1 m x 6.1 m) 20 gpm @ 16.7 psi (75.7 L/min @ 1.15 bar) B1X B1X B1X Installed below ceilings with slopes 11 up to and including a 8/12 (33.7 ) pitch. Refer to Figure 5 on page 149q. UL NYC NSF 8 20 ft. x 20 ft. (6.1 m x 6.1 m) 21 gpm @ 18.4 psi (79.5 L/min @ 1.27 bar) B1X See Footnote 7. B1X 20 ft. x 20 ft. (6.1 m x 6.1 m) 23 gpm @ 22.0 psi (83.4 L/min @ 1.52 bar) C1X See Footnote 7. C1X Approved Temperature Ratings A - 155 F (68 C) and 175 F (79 C) B - 155 F (68 C) C - 175 F (79 C) Approved Finishes 1 - Brass, Chrome-Enloy, White, and Black 12 Approved Escutcheons X - Standard surface-mounted escutcheons or the Microfast Model F-1 Adjustable Escutcheon, or recessed with the Micromatic Model E-1 or E-2 Recessed Escutcheon Footnotes 1 Part number shown is the base part number. For complete part number, refer to current Viking price list schedule. 2 Metric K-factor measurement shown is when pressure is measured in Bar. When pressure is measured in kpa, divide the metric K-factor shown by 10.0. 3 This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. 4 For areas of coverage smaller than shown, use the Minimum Water Supply Requirement for the next larger area listed. Flows and pressures listed are per sprinkler. The distance from sprinklers to walls shall not exceed one-half the sprinkler spacing indicated for the minimum Water Supply Requirement used. 5 Listed by Underwriter s Laboratories for use in the U.S. and Canada. 6 Accepted for use, City of New York Department of Buildings, MEA Number 89-92-E, Vol. 35. 7 Meets New York City requirements, effective July 1, 2008. 8 Tested and Certified by NSF (National Sanitation Foundation) to NSF/ANSI Standard 61, Drinking Water System Components. 9 Listings are for residential occupancies with smooth, flat, horizontal ceilings or horizontal ceilings with beams. Includes ceilings with slopes up to and including a 2/12 (9.5 ) pitch. (For beam ceiling design criteria, refer to Beam Ceiling Guidelines and Figures 6 through 7D on pages 149s-t). 10 Refer to TIA 1028R slope ceiling criteria exceptions. 11 Areas under sloped ceilings must be measured along the ceiling slope. Actual floor coverage in the horizontal plane under sloped ceilings will be less than the listed area of coverage. 12 Other paint colors are available on request with the same culus Listings as the standard finish colors.

Sprinkler 149p January 13, 2012 freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 2: Wrench 12144W/B for Installing Recessed Pendent Sprinkler VK468 Figure 3: Sprinkler VK468 Dimensions dimensions with a Standard standard Escutcheon escutcheon and the Model model F-1 f-1 Adjustable adjustable Escutcheon escutcheon

January 13, 2012 Sprinkler 149q freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 4: Sprinkler VK468 Dimensions dimensions with the Model model E-1 e-1 and E-2 e-2 Recessed recessed Escutcheons escutcheons See Note 1 below. Maximum ceiling slope = 8/12 (33.7 ). Refer to the Approval Chart for listed areas of coverage. Notes: 1. Listed areas of coverage correspond to areas measured along ceiling slope. (For sloped ceiling installations, actual floor coverage in the horizontal plane under sloped ceilings will be less than the listed area.) 2. Actual installations may require multiple sprinklers. A single sprinkler installation has been shown for clarity. 3. For cathedral ceiling applications, install sprinklers in a symmetrical mirror-image of Figure 5. Figure 5: Installation Instructions - Sloped Ceilings

Sprinkler 149r January 13, 2012 freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com DESIGN CRITERIA (Also refer to the Approval Chart on page 149o.) culus Listing Requirements: When using Viking Residential Pendent Sprinkler VK468 for systems designed to NFPA 13D or NFPA 13R, apply the listed areas of coverage and minimum water supply requirements shown in the Approval Chart on page 149o. For systems designed to NFPA 13: The number of design sprinklers is to be the four contiguous most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the following: The flow rates given in the Approval Chart on data page 149o for NFPA 13D and NFPA13R applications for each listed area of coverage, or Calculated based on a minimum discharge of 0.1 gpm/sq. ft. over the design area in accordance with sections 8.5.2.1 or 8.6.2.1.2 of NFPA 13. Minimum distance between residential sprinklers: 8 ft. (2.4 m). BEAM CEILING GUIDELINES culus Listed for installation in residential occupancies with beam ceilings (with horizontal ceilings only). Refer to the Approval Chart for sprinkler areas of coverage and hydraulic design. Sprinkler Location: Locate sprinklers on the underside of the beams (not in the bays or pockets formed by the beams). Refer to Figure 6. The vertical distance from the sprinkler deflector to the bottom of the primary beam must be between 1-1/8 and 1-3/4 (29 to 45 mm). The horizontal distance from the centerline of the sprinkler to the primary beam cannot be more than 2 (51 mm) (Figure 6). NOTE: Consult with a structural engineer before drilling beams to allow the installation of sprinkler drops. Where drilling is not permitted, sprinkler position requirements allow for the sprinkler drop to be placed adjacent to the primary beam. Beam Position: Directly attached to the underside of a combustible or non-combustible smooth ceiling of any height. Beam Size and Shape (Cross section): Depth: Maximum 14 (356 mm) for primary beams. Secondary beam depth cannot be greater than the primary beam. Width: Unlimited. Beam Shape: Rectangular to circular. Beam Types: Combustible or non-combustible, solid surface, solid or hollow core. Beam Spacing: A. For primary beams, the distance from the wall to the center of the nearest primary beam must be at least 3-4 (1.0 m), and not more than one-half the listed sprinkler spacing. Note: Sprinklers may not be required to be located in the first beam nearest the wall. Center-to-center distance between primary beams is to be a maximum of 20 ft (6.1 m). Refer to Figure 7A. B. When beam pockets created by the primary beams exceed 20 ft (6.1 m) in length, secondary beams are required as follows (also refer to Figure 7B): 1. Secondary beam depth must be equal to primary beam depth. 2. Secondary beams must be placed so that the bays formed by the primary beams do not exceed 20 ft (6.1 m) in length. C. When primary beam spans do not exceed 20 ft (6.1 m), secondary beams (not required) may have any distance from wall to nearest secondary beam and any distance center to center between secondary beams. Refer to Figure 7C. Lintels: Must be present over doorways exiting the compartment. Lintel height must be at least 8 (203 mm), or at least the depth of the primary beams, whichever is greater. Beam and Soffit Arrangements: If a soffit is installed, beams may be arranged within the soffit. The cross section of the soffit may be any size, provided it does not create an obstruction to water distribution per the obstruction rules of NFPA 13 for residential sprinklers. Where there is a soffit, beam spacing from the wall is to be measured from the face of the soffit rather than the wall. Refer to Figure 7D. NOTE: The sprinkler area of coverage is to be measured from the wall. Definitions: Primary beams: The main beams that run primarily in one direction. Secondary beams: The beams that run perpendicular to the main beams.

January 13, 2012 Sprinkler 149s freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to pages RES1-17 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA and any other similar Authorities Having Jurisdiction, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Final approval and acceptance of all residential sprinkler installations must be obtained from the Authorities Having Jurisdiction. Figure 6: Sprinkler Positioning Under Primary Beams Figure 7A: Primary Beam Spans up to 20 ft (6.1 m) Figure 7B: Primary Beam Spans over 20 ft (6.1 m)

Sprinkler 149t January 13, 2012 freedom residential pendent sprinkler vk468 (k4.9) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 7C: Combination of Primary and Secondary Beams Figure 7D: Beam and Soffit Arrangements Form No. F_012706 Replaces page 149m-t, dated March 18, 2011. (Revised sprinkler materials and added reference to TIA 1028R.)

March 02, 2012 Sprinkler 156u freedom residential horizontal sidewall sprinkler vk486 (k4.0) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 1. DESCRIPTION Viking Freedom Residential Horizontal Sidewall Sprinkler VK486 is a small, thermosensitive, glass-bulb residential sprinkler available in several different finishes and temperature ratings to meet varying design requirements. The sprinkler orifice design, with a K-Factor of 4.0 (57.7 metric ), allows efficient use of available water supplies for the hydraulically designed fire-protection system. The glass bulb operating element and special deflector characteristics meet the challenges of residential sprinkler standards. 2. LISTINGS AND APPROVALS culus Listed: Category VKKW Refer to the Approval Chart on pages 156w and Design Criteria on page 156x for culus Listing requirements that must be followed. 3. technical data Specifications: Available since 2011. Minimum Operating Pressure: Refer to the Approval Chart. Maximum Working Pressure: 175 psi (12 bar). Factory tested hydrostatically to 500 psi (34.5 bar). Viking Technical Data may be found on Thread size: 1/2 (15 mm) NPT The Viking Corporation s Web site at Nominal K-Factor: 4.0 U.S. (57.7 metric ) http://www.vikinggroupinc.com. Metric K-factor measurement shown is in Bar. When pressure is measured in kpa, divide The Web site may include a more recent the metric K-factor shown by 10.0. edition of this Technical Data Page. Glass-bulb fluid temperature rated to -65 F (-55 C) Overall Length: 2-7/16 (62 mm) Material Standards: Frame Casting: QM Brass and Brass UNS-C84400 Deflector: Phosphor Bronze UNS-C51000 Bulb: Glass, nominal 3 mm diameter Belleville Spring Sealing Assembly: Nickel Alloy, coated on both sides with Teflon Tape Pip Cap and Insert Assembly: Copper UNS-C11000 and Stainless Steel UNS-S30400 Compression Screws: 18-8 Stainless Steel Yoke: Phosphor Bronze UNS-C51000 Ordering Information: (Also refer to the current Viking price list.) Sprinkler: Base Part No. 17315 Order Sprinkler VK486 by first adding the appropriate suffix for the sprinkler finish and then the appropriate suffix for the temperature rating to the sprinkler base part number. Finish Suffix: Brass = A, Chrome-Enloy = F, and White Polyester = M-/W Temperature Suffix: 155 F (68 C) = B, 175 F (79 C) = D For example, sprinkler VK486 with a Brass finish and a 155 F (68 C) temperature rating = Part No. 17315AB. Available Finishes And Temperature Ratings: Refer to Table 1. Accessories: (Also refer to the Sprinkler Accessories section of the Viking data book.) Sprinkler Wrenches: A. Standard Wrench: Part No. 10896W/B (available since 2000) B. Wrench for recessed sprinklers: Part No. 13655W/B* (available since 2006) *A ½ ratchet is required (not available from Viking). Sprinkler Cabinets: A. Six-head capacity: Part No. 01724A (available since 1971) B. Twelve-head capacity: Part No. 01725A (available since 1971) Form No. F_082411 Replaces page 156u-z, issued September 19, 2011. (Added QM Brass to Material Standards and updated Image)

Sprinkler 156v March 02, 2012 freedom residential horizontal sidewall sprinkler Vk486 (k4.0) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com 4. Installation Refer to appropriate NFPA Installation Standards. For NFPA 13D horizontal ceiling criteria and slopes, refer to TIA 1028R for slope ceiling criteria exceptions. 5. Operation During fire conditions, the heat-sensitive liquid in the glass bulb expands, causing the glass to shatter, releasing the yoke, pip cap, and sealing spring assembly. Water flowing through the sprinkler orifice strikes the sprinkler deflector, forming a uniform spray pattern to extinguish or control the fire. 6. inspections, tests and maintenance Refer to NFPA 25 for Inspection, Testing and Maintenance requirements. 7. availability Viking Sprinkler VK486 is available through a network of domestic and international distributors. See The Viking Corporation web site for the closest distributor or contact The Viking Corporation. 8. Guarantee For details of warranty, refer to Viking s current list price schedule or contact Viking directly. Sprinkler Temperature Classification TABLE 1: AVAILABLE SPRINKLER TEMPERATURE RATINGS AND FINISHES Sprinkler Nominal Temperature Rating 1 Maximum Ambient Ceiling Temperature 2 Bulb Color Ordinary 155 F (68 C) 100 F (38 C) Red Intermediate 175 F (79 C) 150 F (65 C) Yellow Sprinkler Finishes: Brass, Chrome-Enloy (patents pending), White Polyester, and Black Polyester. 1 The sprinkler temperature rating is stamped on the deflector. Footnotes 2 Based on NFPA-13. Other limits may apply, depending on fire loading, sprinkler location, and other requirements of the Authority Having Jurisdiction. Refer to specific installation standards. Figure 1: Standard Sprinkler Wrench 10896W/B Figure 2: Wrench 13655W/B for Recessed Sprinkler VK486

March 02, 2012 Sprinker 156w freedom residential horizontal sidewall sprinkler vk486 (k4.0) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Maximum Water Sprinkler Base NPT Thread Size Nominal K-Factor Working Pressure Part Number 1 Inches mm U.S. metric 2 175 psi (12 Bar) Inches Overall Length 17315 1/2 15 4.0 57.7 2-7/16 62 Approval Chart Residential Horizontal Sidewall Sprinkler VK486 For systems designed to NFPA 13D 7 or NFPA 13R. For systems designed to NFPA 13, refer to the design criteria on page 156x. Installed below smooth, flat, horizontal ceilings, including ceilings with slopes up to and including 2/12 (9.5 ). With the deflector located between 4 and 6 (102 mm and 152 mm) below the ceiling. Maximum Areas of Coverage 3 (Width x Length) Minimum Water Supply Requirements 3 Listings and Approvals 4 (Refer also to Design Criteria on page 156x.) culus 5,6 NYC NSF 12 x 12 (3.7 m x 3.7 m) 11 gpm @ 7.6 psi (41.7 L/min @ 0.52 Bar) A1X See Footnote 8. -- 14 x 14 (4.3 m x 4.3 m) 12 gpm @ 9 psi (45.5 L/min @ 0.62 Bar) A1X See Footnote 8. -- 16 x 16 (4.9 m x 4.9 m) 13 gpm @ 10.6 psi (49.3 L/min @ 0.73 Bar) A1X See Footnote 8. -- 16 x 18 (4.9 m x 5.5 m) 16 gpm @ 16 psi (60.6 L/min @ 1.1 Bar) A1X See Footnote 8. -- 16 x 20 (4.9 m x 6.1 m) 22 gpm @ 30.3 psi (83.3 L/min @ 2.09 Bar) A1X See Footnote 8. -- 16 x 22 (4.9 m x 6.7 m) 24 gpm @ 36 psi (90.8 L/min @ 2.48 Bar) A1X See Footnote 8. -- 18 x 18 (5.5 m x 5.5 m) 18 gpm @ 20.3 psi (68.1 L/min @ 1.4 Bar) B1X See Footnote 8. -- 18 x 18 (5.5 m x 5.5 m) 19 gpm @ 22.6 psi (71.9 L/min @ 1.6 Bar) C1X See Footnote 8. -- 18 x 20 (5.5 m x 6.1 m) 22 gpm @ 30.3 psi (83.3 L/min @ 2.09 Bar) A1X See Footnote 8. -- 20 x 20 (6.1 m x 6.1 m) 22 gpm @ 30.3 psi (83.3 L/min @ 2.09 Bar) A1X See Footnote 8. -- Installed below smooth, flat, horizontal ceilings, including ceilings with slopes up to and including 2/12 (9.5 ). With the deflector located between 6 and 12 (152 mm and 305 mm) below the ceiling. 12 x 12 (3.7 m x 3.7 m) 12 gpm @ 9 psi (45.5 L/min @ 0.62 Bar) A1X See Footnote 8. -- 14 x 14 (4.3 m x 4.3 m) 12 gpm @ 9 psi (45.5 L/min @ 0.62 Bar) B1X See Footnote 8. -- 14 x 14 (4.3 m x 4.3 m) 13 gpm @ 10.6 psi (49.3 L/min @ 0.73 Bar) C1X See Footnote 8. -- 16 x 16 (4.9 m x 4.9 m) 14 gpm @ 12.3 psi (53 L/min @ 0.84 Bar) A1X See Footnote 8. -- 16 x 18 (4.9 m x 5.5 m) 16 gpm @ 16 psi (60.6 L/min @ 1.1 Bar) A1X See Footnote 8. -- 16 x 20 (4.9 m x 6.1 m) 23 gpm @ 33.1 psi (87.1 L/min @ 2.28 Bar) A1X See Footnote 8. -- 16 x 22 (4.9 m x 6.7 m) 26 gpm @ 42.3 psi (98.4 L/min @ 2.91 Bar) A1X See Footnote 8. -- 18 x 18 (5.5 m x 5.5 m) 18 gpm @ 20.3 psi (68.1 L/min @ 1.4 Bar) B1X See Footnote 8. -- 18 x 18 (5.5 m x 5.5 m) 19 gpm @ 22.6 psi (71.9 L/min @ 1.6 Bar) C1X See Footnote 8. -- 18 x 20 (5.5 m x 6.1 m) 23 gpm @ 33.1 psi (87.1 L/min @ 2.28 Bar) A1X See Footnote 8. -- 20 x 20 (6.1 m x 6.1 m) 24 gpm @ 36 psi (90.8 L/min @ 2.48 Bar) A1X See Footnote 8. -- Approved Temperature Ratings A - 155 F (68 C) and 175 F (79 C) B - 155 F (68 C) C - 175 F (79 C) Approved Finishes 1 - Brass, Chrome-Enloy, White Polyester, and Black Polyester 9 mm Approved Escutcheons X - Standard surface-mounted escutcheons or the Viking Microfast Model F-1 Adjustable Escutcheon or recessed with the Viking Micromatic Model E-1 or E-2 Recessed Escutcheon, or the Model G-1 Adjustable Escutcheon. Footnotes 1 Base part number shown. For complete part number, refer to Viking s current price list. 2 Metric K-Factor measurement shown is when pressure is measured in Bar. When pressure is measured in kpa, divide the metric K-Factor shown by 10.0. 3 For areas of coverage smaller than shown, use the Minimum Water Supply Requirement for the next larger area listed. Flows and pressures listed are per sprinkler. The distance from sprinklers to walls shall not exceed one-half the sprinkler spacing indicated for the minimum Water Supply Requirement used. 4 This chart shows the listings and approvals available at the time of printing. Other approvals may be in process. Check with the manufacturer for any additional approvals. 5 Listed by Underwriter s Laboratories, Inc. for use in the U.S. and Canada. 6 Listing is for residential occupancies with smooth, flat, horizontal ceilings, including ceilings with slopes up to and including 2/12 (9.5 ). 7 Refer to TIA 1028R slope ceiling criteria exceptions. 8 Meets New York City requirements, effective July 1, 2008. 9 Other paint colors are available on request with the same culus Listings as the standard finish colors.

Sprinkler 156x March 02, 2012 freedom residential horizontal sidewall sprinkler Vk486 (k4.0) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com culus Listing Requirements: DESIGN CRITERIA (Also refer to the Approval Chart on page 156w.) When using Viking Residential Horizontal Sidewall Sprinkler VK486 for systems designed to NFPA 13D or NFPA 13R, apply the listed areas of coverage and minimum water supply requirements shown in the Approval Chart on page 156w. For systems designed to NFPA 13: The number of design sprinklers is to be the four contiguous most hydraulically demanding sprinklers. The minimum required discharge from each of the four sprinklers is to be the greater of the following: The flow rates given in the Approval Chart on data page 156w for NFPA 13D and NFPA 13R applications for each listed area of coverage, or Calculated based on a minimum discharge of 0.1 gpm/sq. ft. over the design area in accordance with sections 8.5.2.1 or 8.6.2.1.2 of NFPA 13. Minimum distance between residential sprinklers: 8 ft. (2.4 m). The VK486 horizontal sidewall sprinkler deflector shall be located a minimum of 1-1/4 (31.8 mm) and a maximum of 6 (152 mm) from the wall on which it is installed. DEFLECTOR POSITION: Install sprinkler VK486 with the leading edge of the deflector oriented parallel to the ceiling and the sprinkler frame arms oriented perpendicular to the ceiling (see Figure 4). THE TOP SURFACE OF THE DEFLECTOR IS MARKED TOP. The sprinkler must be oriented as shown in Figure 3 below. IMPORTANT: Always refer to Bulletin Form No. F_091699 - Care and Handling of Sprinklers. Also refer to pages RES1-17 for general care, installation, and maintenance information. Viking sprinklers are to be installed in accordance with the latest edition of Viking technical data, the appropriate standards of NFPA and any other similar Authorities Having Jurisdiction, and also with the provisions of governmental codes, ordinances, and standards, whenever applicable. Final approval and acceptance of all residential sprinkler installations must be obtained from the Authorities Having Jurisdiction. Figure 3: Correct Orientation of the Deflector

March 02, 2012 Sprinker 156y freedom residential horizontal sidewall sprinkler vk486 (k4.0) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 4: Sprinkler VK486 Dimensions dimensions with a Standard standard Escutcheon escutcheon and the Model model F-1 f-1 Adjustable adjustable Escutcheon escutcheon Figure 5: Sprinkler VK486 Dimensions dimensions with the Model model E-1 e-1 and E-2 e-2 Recessed recessed Escutcheons escutcheons

Sprinkler 156z March 02, 2012 freedom residential horizontal sidewall sprinkler Vk486 (k4.0) Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Figure 6: Sprinkler VK486 Dimensions dimensions with the Model model G-1 Escutcheon escutcheon Form No. F_082411 Replaces page 156u-z, issued September 19, 2011. (Added QM Brass to Material Standards and updated Image)

Worldwide Contacts www.tyco-fire.com Series DS-1 5.6 K-factor, Dry-type Sprinklers Pendent, Upright, and Horizontal Sidewall Standard Response, Standard Coverage General Description TYCO Series DS-1 5.6K Pendent, Upright, and Horizontal Sidewall, Standard Response (5 mm bulb), Standard Coverage Dry-type Sprinklers are decorative glass bulb automatic sprinklers typically used where: pendent sprinklers are required on dry pipe systems that are exposed to freezing temperatures (e.g., sprinkler drops from unheated portions of buildings) sprinklers and/or a portion of the connecting piping may be exposed to freezing temperatures (e.g., sprinkler drops from wet systems into freezers, sprinkler sprigs from wet systems into unheated attics, or horizontal piping extensions through a wall to protect unheated areas of a building such as loading docks, overhangs, and building exteriors) sprinklers are used on systems that are seasonably drained to avoid freezing (e.g., vacation resort areas) NOTICE Series DS-1 Dry-type Sprinklers described herein must be installed and maintained in compliance with this document, as well as with the applicable standards of the National Fire Protection Association (NFPA), in addition to the standards of any other authorities having jurisdiction. Failure to do so may impair the performance of these devices. IMPORTANT Always refer to Technical Data Sheet TFP700 for the INSTALLER WARNING that provides cautions with respect to handling and installation of sprinkler systems and components. Improper handling and installation can permanently damage a sprinkler system or its components and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. The owner is responsible for maintaining their fire protection system and devices in proper operating condition. Contact the installing contractor or product manufacturer with any questions. Series DS-1 Dry-type Sprinklers must only be installed in fittings that meet the requirements of the Design Criteria section. Sprinkler Identification Numbers (SINs) TY3255 Pendent TY3155 Upright TY3355 Horizontal Sidewall Technical Data Approvals UL and C-UL Listed FM Approved VdS Approved TY3255 w/standard Escutcheon only NYC Approved under MEA 352-01-E LPCB Approved Reference No. 094a/11 CE Certified Certificate of Conformity No. 0832- CPD-2015 (Refer to Tables A and B for details.) Maximum Working Pressure 175 psi (12,1 bar) Inlet Thread Connections 1 inch NPT ISO 7-R 1 Discharge Coefficient K=5.6 gpm/psi 1/2 (80,6 lpm/bar 1/2 ) Temperature Ratings Refer to Tables A and B. Finishes Sprinkler: Refer to Table D. Escutcheon: Refer to Table D. Physical Characteristics Inlet......................... Copper Plug........................ Copper Yoke.................. Stainless Steel Casing...Galvanized Carbon Steel Insert....................... Bronze Bulb Seat...Stainless Steel Bulb (5 mm dia.)................ Glass Compression Screw............ Bronze Deflector..................... Bronze Frame....................... Bronze Guide Tube....Stainless Steel Water Tube...Stainless Steel Spring....Stainless Steel Sealing Assembly....... Beryllium Nickel w/teflon Escutcheon............. Carbon Steel Page 1 of 10 JANUARY 2015 TFP500