Testing laboratory locations: 1. Testing Laboratory in Prague (0100) Prosecká 811/76a, 190 00 Praha 9 2. Testing Laboratory in České Budějovice (0200) 3. Testing Laboratory in Plzeň (0300) Zahradní 15, 326 00 Plzeň Slovany 4. Testing Laboratory in Teplice (0400) Tolstého 447, 415 03 Teplice 5. Testing Laboratory in Předměřice n. L. (0500) Průmyslová 283, 503 02 Předměřice nad Labem 6. Testing Laboratory in Brno (0600) Hněvkovského 77, 617 00 Brno 7. Testing Laboratory in Ostrava (0700) U Studia 14, 700 30 Ostrava The Laboratory is qualified to update standards identifying the test procedures. Tests: 1. Testing Laboratory in Prague 1.2 Concrete, admixtures and fibres for concrete 1.2.1* Slump test ČSN EN 12350-2 Fresh concrete 1.2.2* VeBe test ČSN EN 12 350-3 Fresh concrete 1.2.3* Flow table test ČSN EN 12 350-5 Fresh concrete 1.2.4* mass per unit volume ČSN EN 12350-6 Fresh concrete 1.2.5* air content ČSN EN 12 350-7 pressure methods Fresh concrete 1.2.6 concrete frost resistance ČSN 73 1322 1.2.7 cement concrete surface resistance to water and chemical de-icing ČSN 73 1326, A, C method agents 1.2.8* Testing of shapes and dimensions ČSN EN 12390-1 1.2.9* compressive strength of concrete, including the manufacture and treatment of test specimens ČSN EN 12390-2 ČSN EN 12390-3 ČSN EN 12504-1 1.2.10 compressive ČSN EN 12390-3 strength of test specimens 1.2.11 flexural strength of test specimens ČSN EN 12390-5 1.2.12 the indirect tensile strength of test specimens ČSN EN 12390-6 Page 1 of 110 --20130510
1.2.13 density of hardened concrete ČSN EN 12390-7 1.2.14 depth of penetration of water under ČSN EN 12390-8 pressure 1.2.15 static modulus of elasticity in ČSN ISO 1920-10 compression 1.2.16* Test of compressive strength ČSN EN 12504-1 1.2.17* rebound by hardness drop ČSN EN 12504-2 tester 1.2.18* Test of compressive strength by hardness testing methods (Schmidt N. L.) ČSN 73 1373 1.2.19 setting time ČSN EN 480-2 Concrete and mortar additives 1.2.20 bleeding of Concrete and mortar ČSN EN 480-4 concrete additives 1.2.21 capillary Concrete and mortar ČSN EN 480-5 absorption additives 1.2.22 solids Concrete and mortar ČSN EN 480-8 content additives 1.2.23 air void Concrete and mortar characteristics in hardened ČSN EN 480-11 additives concrete 1.2.24 1.2.25 1.2.26 flexural tensile strength (limit of proportionality, residual strength) dry bulk density mechanical properties (compressive strength, flexural strength, concentric compressive strength) 1.3 Small concrete products ČSN EN 14651+A1 ČSN EN 678 ČSN EN 679 Metallic fibre-reinforced concrete Autoclaved concrete Aerated concrete 1.3.1* dimensions ČSN EN 1338 Annex C 1.3.2* dimensions ČSN EN 1339 Annex C 1.3.3* dimensions ČSN EN 1340 Annex C 1.3.4 total water absorption ČSN EN 1338 Annex E Page 2 of 110 --20130510
1.3.5 1.3.6 1.3.7 1.3.8 1.3.9 1.3.10 1.3.11 1.3.12 1.3.13 total water absorption total water absorption the indirect tensile strength flexural strength and fracture load bending strength abrasiveness Bohme resistance to freezing/thawing resistance to freezing/thawing resistance to freezing/thawing ČSN EN 1339 Annex E ČSN EN 1340 Annex E ČSN EN 1338 Annex F ČSN EN 1339 Annex F ČSN EN 1340 Annex F ČSN EN 1338 Annex H ČSN EN 1338 Annex D ČSN EN 1339 Annex D ČSN EN 1340 Annex D 1.4 Concrete building components and structures 1.4.1* shapes and dimensions, appearance ČSN 73 0212-5 1.4.2* dimensions ČSN EN 991 1.4.3 1.4.4 1.4.5 1.4.6 1.4.7 1.4.8 Tests of strength and load bearing capacity Tests of strength and load bearing capacity shear load capacity mechanical durability and stability - by test impact strength mass of components Building components Lightweight and aerated concrete components ČSN EN 1916 only Annex C Concrete pipes ČSN EN 1917 except Annex C, D ČSN EN 1168+A3 Annex J ČSN EN 1520 ed. 2 Annex B ČSN 73 2035 ČSN 73 2045 Concrete manholes Hollow core slabs Reinforced components of lightweight concrete Building components Building components 1.5 Timber, timber components, timber based and fibre-cement products 1.5.1* Static loading tests ČSN EN 380 Timber structures 1.5.2 loadbearing capacity and stiffness ČSN EN 594 Timber structures 1.5.3 bearing capacity and deformation ČSN EN 595 Timber structures behaviour 1.5.4 Soft body impact test ČSN EN 596 Timber structures Page 3 of 110 --20130510
1.5.5 physical and mechanical properties ČSN EN 408+A1 Structural and glued timber 1.5.6 Visual determination of Coniferous sawn timber for ČSN 73 2824-1 grading characteristics structural elements 1.5.7 Shear test ČSN EN 14080 Annex D Glued timber 1.5.8* Testing of dimensions and geometrical characteristics ČSN EN 12467+A1 p. 7.2 Fibre-cement flat sheets 1.5.9* moisture content ČSN EN 13183-2 Structural timber 1.5.10 moisture content ČSN EN 322 Wood-based panels 1.5.11 hard body Cement-bonded ČSN EN 1128 impact resistance particleboards 1.5.12 Testing of joints of timber Fixtures for timber ČSN EN 1380 structures structures 1.5.13 Testing of joints of timber Fixtures for timber ČSN EN 1075 structures structures 1.5.14 Testing of joints of timber Fixtures for timber ČSN EN 1381 structures structures 1.5.15 Testing of joints of timber Fixtures for timber ČSN EN 1382 structures structures 1.5.16 Testing of joints of timber Fixtures for timber ČSN EN 1383 structures structures 1.5.17 Testing of joints of timber Fixtures for timber ČSN EN 26891 structures structures 1.5.18 dimensions ČSN EN 14592+A1 p. 5 Fasteners for timber structures 1.5.19 torsional resistance of driving in screws 1.6 Physical factors 1.6.1 Reserved ČSN EN 15737 1.7 Glass grids, geotextiles and geotextile-related products 1.7.1 tensile strength and elongation of mesh ČSN EN 13496 1.9 Materials, products and waterproofing systems Fasteners for timber structures Glass fibre mesh 1.9.1 length, width and straightness ČSN EN 1848-1 Asphalt sheets 1.9.2 length, width and straightness ČSN EN 1848-2 Plastic and rubber sheets 1.9.3 thickness ČSN EN 1849-1 Asphalt sheets 1.9.4 mass per unit area ČSN EN 1849-1 Asphalt sheets Page 4 of 110 --20130510
1.9.5 thickness ČSN EN 1849-2 Plastic and rubber belts 1.9.6 mass per Plastic and rubber belts and ČSN EN 1849-2 unit area sheets 1.9.7 visible defects ČSN EN 1850-1 Asphalt sheets 1.9.8 visible Plastic and rubber belts and ČSN EN 1850-2 defects sheets 1.9.9 flow resistance ČSN EN 1110 Asphalt sheets 1.9.10 tensile properties ČSN EN 12311-1 Asphalt sheets 1.9.11 tensile Plastic and rubber belts and ČSN EN 12311-2 properties sheets 1.9.12 Reserved 1.9.13* 1.9.14 1.9.15 1.9.16 1.9.17 1.9.18 1.9.19 1.9.20 1.9.21 1.9.22 1.9.23 1.9.24 1.9.25 1.9.26 tensile adhesion strength watertightness watertightness water vapour permeability water vapour transmission properties dimensional stability dimensional stability resistance to long term exposure to elevated temperature resistance to blistering geometrical properties water absorption mass per unit area of bitumen resistance to delamination resistance to wind load ČSN EN 13596 ČSN EN 1928 ČSN EN 15820 ČSN EN 1931 ČSN EN ISO 12572 ČSN EN 1107-1 ČSN EN 1107-2 ČSN EN 1296 ČSN EN 544 ed. 2 p. 6.4.5 ČSN EN 544 ed. 2 p. 6.3 ČSN EN 544 ed. 2 p. 6.4.3 ČSN EN 544 ed. 2 p. 6.2 EOTA TR 004 EOTA TR 005 Waterproofing of concrete bridge decks Bitumen, plastic and rubber belts and sheets Bituminous polymermodified cements Bitumen, plastic and rubber belts and sheets Hygroscopic, nonhygroscopic building materials, sheathed products Asphalt sheets Plastic and rubber belts, sheets Bitumen, plastic and rubber belts and sheets Bitumen shingles Bitumen shingles Bitumen shingles Bitumen shingles Cast roof waterproofing assemblies Cast roof waterproofing assemblies Page 5 of 110 --20130510
1.9.27 1.9.28 1.9.29 1.9.30 1.9.31 1.9.32 1.9.33 1.9.34 1.9.35 1.9.36 1.9.37 1.9.38 watertightness resistance to artificial ageing (fluorescence UV lamps) resistance to artificial ageing by long term exposure to the combination of UV radiation, elevated temperature and water resistance to dynamic indentation resistance to static indentation accelerated ageing by heat accelerated ageing by hot water the effects liquid chemicals, including water peel resistance of joints (fissility of sheets) resistance to tearing (nail shank) peel resistance of joints shear resistance of joints ČSN EN 14891 method A.7 EOTA TR 010 ČSN EN 1297 EOTA TR 006 EOTA TR 007 except 5.2.5 c) EOTA TR 011 EOTA TR 012 ČSN EN 1847 ČSN EN 12316-1 ČSN EN 12310-1 ČSN EN 12316-2 ČSN EN 12317-2 1.12 Stone, aggregates, inactive concrete admixtures, soils 1.12.1 1.12.2 1.12.3 1.12.4 resistance to freezing and thawing particle size distribution Sieving analysis particle shape - Shape index percentage of crushed and broken surfaces in coarse aggregate particles ČSN EN 1367-1 ČSN EN 933-1 ČSN EN 933-4 ČSN EN 933-5 Liquid-applied water impermeable products used under ceramic tiling Cast roof waterproofing assemblies, etc. Bitumen, plastic and rubber belts and sheets Cast roof waterproofing assemblies, etc. Cast roof waterproofing assemblies, etc. Cast roof waterproofing assemblies, etc. Cast roof waterproofing assemblies Plastic and rubber belts and sheets Asphalt sheets Asphalt sheets Plastic and rubber belts and sheets Plastic and rubber belts and sheets Page 6 of 110 --20130510
1.12.5 1.12.6 1.12.7 1.12.8 resistance to fragmentation loose bulk density and voids the water content by drying in a ventilated oven particle density and water absorption ČSN EN 1097-2 ČSN EN 1097-3 ČSN EN 1097-5 ČSN EN 1097-6 1.12.9 Magnesium sulfate test ČSN EN 1367-2 1.12.10 density and water absorption ČSN EN 14617-1 1.14 Metallic materials and parts in construction Artificial stone 1.14.1* Performance of tensile tests ČSN EN ISO 6892-1 Metallic products 1.14.2 Performance of tensile tests ČSN EN ISO 15630-1 p. 5 Metallic products 1.14.3 Performance of tensile tests 1.14.4 Performance of tensile tests ČSN EN ISO 17660-1 p. 14.2 ČSN EN ISO 17660-2 p. 14.2 Metallic products Metallic products 1.14.5 Bend test ČSN EN ISO 7438 p. 4.1. Metallic products 1.14.6 Bend test 1.14.7 Bend test 1.14.8* 1.14.9 shape and dimensional accuracy of wrought products angle accuracy ČSN EN ISO 17660-1 p. 14.4 ČSN EN ISO 17660-2 p. 14.4 ČSN EN ISO 15630-1 p. 10, 11 ČSN EN 14195 Metallic products Metallic products Metallic products Metallic products 1.14.10 Performance of fatigue tests ČSN EN ISO 15630-1 p. 8 Metallic products 1.14.11* the quality of metal coating microscopic test ČSN EN ISO 1463 Metallic products 1.14.12 Shear test ČSN EN ISO 17660-1 p. 14.3 Metallic products 1.14.13 Shear test ČSN EN ISO 17660-2 p. 14.3 Metallic products 1.14.14 Shear test ČSN EN 10080 Annex B.3, Truss beams of concrete method 1 reinforcing steel 1.14.15 Salt spray test ČSN EN ISO 9227 p. 5.2 Metallic products Page 7 of 110 --20130510
1.14.16 1.14.17 dimensions and limit deviations of organic coats torsional strength ČSN EN 10245-1 Metallic products ČSN EN ISO 10666 p. 4.2.3 Drilling screws 1.17 Mortars, mortar mixtures, renovation materials, screeds 1.17.1 Frost resistance test ČSN 72 2452 Masonry mortars 1.17.2 1.17.3 1.17.4 1.17.5 1.17.6 1.17.7 1.17.8 consistence of fresh mortar by flow table consistence of fresh mortar by plunger penetration density of fresh mortar air content of fresh mortar workable life and correction time of fresh mortar dry bulk density of hardened mortar compressive strength of mortar ČSN EN 1015-3 ČSN EN 1015-4 ČSN EN 1015-6 ČSN EN 1015-7 ČSN EN 1015-9 ČSN EN 1015-10 ČSN EN 1015-11 Fresh mortar Fresh mortar Fresh mortar Fresh mortar Fresh mortar Dry mortar Dry hardened mortar 1.17.9 Test of compressive strength ČSN EN 13892-2 Screed materials 1.17.10 flexural strength of mortar ČSN EN 1015-11 Dry hardened mortar 1.17.11 Test of flexural strength ČSN EN 13892-2 Screed materials 1.17.12* adhesion ČSN EN 1015-12 Dry hardened mortar 1.17.13 adhesion of cementitious adhesives ČSN EN 12004-2 Mortars and adhesives 1.17.14* adhesion ČSN EN 13892-8 Screed materials 1.17.15 1.17.16 water absorption coefficient due to capillary action of hardened mortar water vapour permeability of surface finish of building structures ČSN EN 1015-18 ČSN EN 1015-19 Mortars Mortars Page 8 of 110 --20130510
1.17.17 slip ČSN EN 12004-2 Mortars and adhesives 1.17.18 shear adhesion strength of dispersion adhesives ČSN EN 12004-2 Mortars and adhesives 1.17.19 open time ČSN EN 12004-2 Mortars and adhesives 1.17.20 1.17.21 shear adhesion strength of reaction resin adhesives abrasion resistance (Böhme) ČSN EN 12004-2 ČSN EN 13892-3 1.17.22 wear resistance by BCA method ČSN EN 13892-4 1.17.23 surface hardness ČSN EN 13892-6 1.17.24 dimensional ČSN EN 13872 variations 1.17.25 resistance of renovation plasters to salt WTA 2-9-04/D p. 6.3.10 bleeding, ČSN EN 445 p. 4.3, 4.4, 4.5, 1.17.26* volume changes, fluidity and 4.6 compressive strength 1.17.27 linear shrinkage ČSN EN 12617-1 thermal 1.17.28 compatibility Freeze-thaw cycling with de-icing salt ČSN EN 13687-1 immersion 1.17.29 shrinkage and expansion ČSN EN 12617-4 p. 6 1.17.30 compressive ČSN EN 12190 strength of repair mortar 1.17.31 1.17.32 1.17.33* 1.17.34 resistance to capillary absorption resistance to carbonation depth carbonation depth abrasion resistance ČSN EN 13057 ČSN EN 13295 ČSN EN 14630 ČSN EN ISO 5470-1 Mortars and adhesives Screed materials Screed materials Screed materials Screed materials Renovation plasters Injection mortars Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials 1.17.35 Pull-out test ČSN EN 1881 Renovation materials 1.17.36 Measurement of bond strength by pull-off ČSN EN 1542 Renovation materials Page 9 of 110 --20130510
1.17.37 1.17.38 1.17.39 1.17.40 modulus of ČSN EN 13412 elasticity in compression carbon dioxide permeability ČSN EN 1062-6 p. 8.1 method A resistance to severe chemical attack ČSN EN 13529 method without pressure tensile bond strength (to steel and concrete EGOLF EA 05, p. 5 structures) 1.20 Draining elements 1.20.1 Load test ČSN EN 1433 p. 9.1 1.20.2 1.20.3 1.20.4 1.20.5 dimensions and shape resistance to frost and chemical de-icing agents dimensions, shape physicomechanical characteristics ČSN EN 1433 p. 9.3 ČSN EN 1433 Annex C ČSN EN 124-1 p. 8.4 ČSN EN 1433 1.20.6 Permanent set test ČSN EN 124-1, Annex A 1.20.7 Test of load bearing capacity ČSN EN 124-1, Annex B 1.21 Doors and windows, roof lights, hardware 1.21.1 air permeability of windows and doors ČSN EN 1026 1.21.2 Air permeability test of gates ČSN EN 12427 Gates 1.21.3 1.21.4 1.21.5 Watertightness test of windows and doors Test of window and door resistance to wind load Test of gate resistance to wind load ČSN EN 1027 ČSN EN 12211 ČSN EN 12444 Renovation materials Renovation materials Renovation materials Fire protection mortars Drainage channels for vehicular and pedestrian areas Drainage channels for vehicular and pedestrian areas Drainage channels for vehicular and pedestrian areas Gully tops and manhole tops Drainage channels for vehicular and pedestrian areas Gully tops and manhole tops Gully tops and manhole tops Windows, doors Windows, doors Windows, doors Gates Page 10 of 110 --20130510
1.21.6 1.21.7 1.21.8 1.21.9 1.21.10 1.21.11 1.21.12 1.21.13 1.21.14 1.21.15 1.21.16 1.21.17 1.21.18 1.21.19 the strength of welded corners of PVC-U profiles for the manufacture of windows and doors thermal transmittance of windows, doors and gates - by test - by calculation thermal transmittance of window and door frames - by test - by calculation thermal transmittance of roof lights - by test - by calculation gate resistance to water penetration window operating force door operating force the resistance to soft and heavy body impact for doors the resistance to soft and heavy body impact for windows the resistance of doors to static torsion the resistance of windows to static torsion resistance of doors to racking resistance of windows to racking resistance of door leaves to hard body impact ČSN EN 514 ČSN EN ISO 12567-1 ČSN EN ISO 10077-1 p. 5 (windows, doors) ČSN EN 12428 (gates) ČSN EN 12412-2 ČSN EN ISO 10077-2 p. 4, Annex C ČSN EN ISO 12567-2 ČSN EN 1873+A1, Annex D ČSN EN 12489 ČSN EN 12046-1 ČSN EN 12046-2 ČSN EN 949 ČSN EN 13049 ČSN EN 948 ČSN EN 14609 ČSN EN 947 ČSN EN 14608 ČSN EN 950 PVC-U profiles Windows, doors and gates Window and door frames Roof lights, roof windows Gates Windows Doors Doors Windows Doors Windows Doors Windows Door leaves Page 11 of 110 --20130510
1.21.20 resistance to upward load ČSN EN 1873+A1, p. 6.5.1 Individual rooflight 1.21.21 resistance to downward load ČSN EN 1873+A1, p. 6.5.1 Individual rooflight 1.21.22 1.21.23 1.21.24 resistance to small hard body impact ČSN EN 1873+A1, p. 6.5.2 resistance ČSN EN 1873+A1, p. 6.5.2 to large soft body impact thermal ČSN EN 673 transmittance by calculation Glazing 1.23 Plastics and composites 1.23.1 1.23.2 1.23.3 1.23.4 1.23.5 1.23.6 1.23.7 1.23.8 1.23.9 1.23.10 1.23.11 1.23.12 1.23.13 1.23.14 resistance to artificial ageing fluorescence UV lamps water absorption of plastics tensile properties tensile properties tensile properties compressive properties flexural properties the effects of immersion in liquid chemicals (including water) linear dimensions mass per unit volume thickness, width and length mass per unit area flexural properties resistance to compression ČSN EN ISO 4892-3 ČSN EN ISO 62 ČSN EN ISO 527-1 ČSN EN ISO 527-2 ČSN EN ISO 527-3 ČSN EN ISO 604 ČSN EN ISO 178 Individual rooflight Individual rooflight Plastics, rubbers, bitumen Plastics Plastics Plastics Plastics ČSN EN ISO 175, p. 5.4, 5.6 Plastics ČSN EN ISO 1923 ČSN EN ISO 845 ČSN EN ISO 12017, p. 6.2, 6.3 ČSN EN ISO 12017 ČSN EN ISO 12017 ČSN EN ISO 3386-1 Thermoplastics, thermosets and thermotropic polymers on the basis of liquid crystals Thermoplastics and thermosets Cellular plastics and rubber Cellular plastics and rubbers Plastics (e.g. PMMA) Plastics (e.g. PMMA) Plastics (e.g. PMMA) Flexible cellular polymers (low density) Page 12 of 110 --20130510
1.23.15 1.23.16 the resistance to impact of main profiles by falling mass Shore hardness ČSN EN 477 ČSN EN ISO 868 Unplasticised polyvinyl chloride (PVC-U) profiles Plastics 1.24 Construction cements, fly ash, slags, stabilization of soils, bitumens 1.24.1 1.24.2 1.24.3 normal consistency and setting time of cement volume stability of cement the strength of cement ČSN EN 196-3 p. 1-6 ČSN EN 196-3 p. 7 ČSN EN 196-1 Cement, masonry cement Cement, masonry cement Cement, masonry cement 1.26 Gypsum and gypsum products, rock gypsum, anhydride, MgO based panels 1.26.1 1.26.2 flexural strength compressive strength ČSN EN 13279-2 ČSN EN 13279-2 1.26.3 adhesion ČSN EN 13963 ed. 2 1.26.4 Reserved 1.26.5 Reserved Gypsum binders and gypsum plasters Gypsum binders and gypsum plasters Jointing materials for gypsum boards 1.26.6 setting time ČSN EN 13963 ed. 2 Jointing materials 1.26.7 total water absorption ČSN EN 520+A1 p. 5.9.2 1.26.8 width ČSN EN 13950 1.26.9 thickness ČSN EN 13950 1.26.10 adhesion ČSN EN 13950 1.26.11 width ČSN EN 13950 ed. 2 1.26.12 thickness ČSN EN 13950 ed. 2 Plasterboards Gypsum board thermal/acoustic insulation composite panels Gypsum board thermal/acoustic insulation composite panels Gypsum board thermal/acoustic insulation composite panels Gypsum thermal/acoustic insulation composite panels Gypsum thermal/acoustic insulation composite panels Page 13 of 110 --20130510
1.26.13 adhesion ČSN EN 13950 ed. 2 Gypsum thermal/acoustic insulation composite panels 1.29 Cements, adhesives, jointing materials, paints and coatings, surface finishes 1.29.1* adhesion ČSN 73 2577 Surface finish 1.29.2* watertightness ČSN 73 2578 Surface finish 1.29.3 resistance to ČSN 73 2579 frost Surface finish water 1.29.4 vapour transmission properties ČSN 73 2580 Surface finish 1.29.5 resistance to ČSN 73 2581 rapid temperature changes Surface finish 1.29.6 resistance to ČSN 73 2582 abrasion Surface finish 1.29.7 resistance to ČSN EN ISO 2812-1 liquids Surface finish 1.29.8 resistance to ČSN EN ISO 2812-4 liquids Surface finish 1.29.9 Pull-off test for adhesion ČSN EN ISO 4624 Surface finish 1.29.10 water vapour transmission rate ČSN EN ISO 7783 Surface finish 1.29.11 water permeability ČSN EN 1062-1 p. 5.6 Surface finish 1.29.12 water permeability ČSN EN 1062-3 Surface finish 1.29.13 Drop weight test ČSN EN ISO 6272-1 Surface finish 1.29.14* Cross-cut test ČSN EN ISO 2409 Surface finish 1.29.15* thickness ČSN EN ISO 2808 Surface finish 1.29.16 resistance to ČSN EN ISO 6270-1 humidity Surface finish 1.29.17 Assessment of degree of blistering ČSN EN ISO 4628-2 Surface finish 1.29.18 Assessment of degree of rusting ČSN EN ISO 4628-3 Surface finish 1.29.19 Assessment of degree of cracking ČSN EN ISO 4628-4 Surface finish 1.29.20 Assessment of degree of flaking ČSN EN ISO 4628-5 Surface finish 1.29.21 Assessment of degree of delamination and corrosion around a scribe ČSN EN ISO 4628-8 Surface finish 1.29.22 Reserved Page 14 of 110 --20130510
1.29.23 abrasion resistance - TABER- ČSN EN ISO 7784-1 Surface finish ABRASER 1.29.24 abrasion resistance - TABER- ČSN EN ISO 7784-2 Surface finish ABRASER 1.29.25 colour ČSN EN ISO 3668 Surface finish specular 1.29.26* gloss ČSN EN ISO 2813 Surface finish resistance to 1.29.27 artificial ageing UV lamps ČSN EN 927-6 Surface finish and water 1.29.28 nonvolatile-matter content ČSN EN ISO 3251 Surface finish 1.29.29 elastic recovery ČSN EN ISO 7389 Sealants 1.29.30 resistance to ČSN EN ISO 7390 flow Sealants 1.29.31 adhesion and cohesion ČSN EN ISO 9046 Sealants 1.29.32 volume changes ČSN EN ISO 10563 Sealants 1.29.33 adhesion and cohesion at maintained extension after immersion in ČSN EN ISO 10590 Sealants water 1.29.34 adhesion and cohesion properties after ČSN EN ISO 10591 Sealants immersion in water 1.29.35 tensile properties ČSN EN ISO 8339 p. 8.2 Sealants 1.29.36 tensile properties at maintained extension ČSN EN ISO 8340 Sealants 1.29.37 resistance to ČSN EN ISO 11432 compression Sealants 1.29.38 chemical resistance ČSN EN 12808-1 Grouts for tiles 1.29.39 flexural and compressive strength ČSN EN 12808-3 Grouts for tiles 1.29.40 shrinkage ČSN EN 12808-4 Grouts for tiles 1.29.41 water absorption ČSN EN 12808-5 Grouts for tiles Page 15 of 110 --20130510
1.29.42 ageing resistance exposure to offshore and related environments ČSN ISO 20340 Annex A 1.30, thermal tests 1.30.1 1.30.2 1.30.3* tensile strength parallel to faces setting of blown insulation length and width ČSN EN 1608 ČSN EN 15101-1 Annex B, method B.2 ČSN EN 822 1.30.4* thickness ČSN EN 823 1.30.5 Pressure test ČSN EN 826 1.30.6 1.30.7 1.30.8 1.30.9 1.30.10 1.30.11 1.30.12 1.30.13 1.30.14 shear strength in axial direction shear strength in axial direction tensile strength perpendicular to faces dimensional stability under specified temperature and humidity conditions dimensional stability at constant laboratory conditions water absorption by partial immersion long term water absorption by immersion elongation at break the content of pores and air voids ČSN EN 253+A2 p. 5.4.1 ČSN EN 15632-4 p. 6.2 ČSN EN 1607 ČSN EN 1604 ČSN EN 1603 ČSN EN 1609 ČSN EN 12087 ČSN EN 253+A2 p. 5.2.2 ČSN EN 253+A2 p. 5.3.2 1.30.15 Measurement of diameter ČSN EN 253+A2 p. 4.2.2 1.30.16 Measurement of diameter ČSN EN 253+A2 p. 4.3.2.1 Surface finish Page 16 of 110 --20130510
1.30.17 1.30.18 1.30.19 Measurement of wall thickness Measurement of wall thickness water vapour transmission rate ČSN EN 253+A2 p. 4.2.3 ČSN EN 253+A2 p. 4.3.2.2 ČSN EN 12086 1.30.20 Bend test ČSN EN 12089 1.30.21 1.30.22 1.30.23 1.30.24 1.30.25 1.30.26 1.30.27 1.30.28 1.30.29 1.30.30 1.30.31 1.30.32 mass per unit volume steady-state thermal transmission properties - by test - by calculation impact resistance setting of blown insulation metal corrosion resistance thermal resistance by means of guarded hot plate and heat flow meter methods tensile strength perpendicular to faces compressive strength of self-supporting double skin insulating panels shear strength of self-supporting double skin insulating panels bending moment capacity of selfsupporting double skin insulating panels durability of self-supporting double skin insulating panels the reaction profile and free-rise density ČSN EN 1602 ČSN EN ISO 8990 ČSN EN ISO 6946 p. 5, 7 ČSN EN ISO 10211 ČSN EN 253+A2 p. 5.4.6 ISO/CD 18393 ČSN EN 15101-1 Annex E ČSN EN 12667 ČSN EN 14509, Annex A1 ČSN EN 14509, Annex A.2 ČSN EN 14509, Annex A.3 ČSN EN 14509, Annex A.5 ČSN EN 14509, Annex B ČSN EN 14315, Annex E Building materials and structures Thermal insulating materials materials materials double skin faced panels materials double skin faced insulating panels materials double skin faced insulating panels materials double skin faced insulating panels materials double skin faced insulating panels Thermal insulating materials PUR foams Page 17 of 110 --20130510
1.30.33 1.30.34 substrate adhesion strength perpendicular to faces Reaction to fire tests Part 2: Single-flame source test ČSN EN 14315, Annex F ČSN EN ISO 11925-2 1.31 Road equipment, road signs, lighting poles 1.31.1 1.31.2 Impact test (verification of secondary safety risk of falling debris) Testing of stone impact resistance 1.32 systems 1.32.1 1.32.2 1.32.3 1.32.4 1.32.5 1.32.6 1.32.7 1.32.8 adhesion to the substrate resistance to frost tensile strength and elongation of mesh water absorption impact resistance density of fresh mortar mass per unit area of reinforcement mesh dry bulk density of hardened mortar ČSN EN 1794-2 Annex B ČSN EN 1794-1 Annex C ETAG 004 p. 5.1.4.1, 5.1.7.1 EAD 040089-00-0404 p. 2.2.3.1, 2.2.3.3, 2.2.3.4, 2.2.3.20, 2.2.3.21 ETAG 004 p. 5.1.3.2.2 EAD 040089-00-0404, p. 2.2.2.3 ETAG 004 p. 5.6.7.1 EAD 040089-00-0404, p. 2.2.3.23, 2.2.3.24, 2.2.3.25 ETAG 004 p. 5.1.3.1 EAD 040089-00-0404, p. 2.2.2.1 ETAG 004 p. 5.1.3.3. EAD 040089-00-0404, p. 2.2.3.19 ETAG 004 p. C.1.2.2 ETAG 004 p. C.3.1 ETAG 004 p. C.1.3 Thermal insulating materials PUR foams Thermal insulating materials and building materials Elements of noise barriers Elements of noise barriers Adhesive and screed materials for ETICS Mortars ETICS meshes ETICS ETICS Fresh mortar ETICS Mesh ETICS Base layer ETICS 1.32.9 grain size ETAG 004 p. C.1.1.4 Pastes, powders ETICS 1.33 Loading tests of bridges, building structure and floors 1.33.1* Loading tests of bridges ČSN 73 6209 Bridges 1.33.2* Loading tests of bridges STN 73 6209 Bridges 1.33.3* Load tests ČSN 73 2030 Annex A, B, C Bearing structures and their parts Page 18 of 110 --20130510
1.34 Masonry, hardware, partition walls, ceilings, floors 1.34.1 1.34.2 1.34.3 impact resistance impact resistance - small hard body impact resistance large soft body ISO 7892 EOTA TR 001, p. 3 EOTA TR 001, p. 2 Ventilated facades, partition walls, hand rails Wall panels Wall panels 1.35 Masonry units, permanent formwork, ceiling elements, burnt and concrete roofing 1.35.1 water permeability ČSN EN 539-1 Clay roofing tiles 1.35.2 dimensions ČSN EN 772-16 Masonry units 1.35.3 1.35.4 1.35.5 1.35.6 1.35.7 1.35.8 1.35.9 1.35.10 1.35.11 1.35.12 mechanical properties of masonry materials and burnt roofing mechanical properties of masonry materials and burnt roofing fracture load of ceiling materials resistance to frost frost resistance of calcium silicate masonry units Testing of dimensional tolerances and mass percentage area of voids in concrete blocks (by paper indentation) net volume and percentage of voids and material in calcium silicate masonry units by filling the voids with sand geometrical characteristics moisture content of calcium silicate masonry units and aerated concrete units ČSN 72 2605 ČSN EN 538 ČSN 72 2642, p. 13 ČSN 72 2601 Annex A ČSN EN 772-18 ČSN EN 491 p. 5.2-5.5 ČSN EN 772-2 ČSN EN 772-9 ČSN EN 1024 ČSN EN 772-10 Brick products Clay roofing tiles Brick products Brick products Masonry units Concrete roofing tiles Masonry units Masonry units Clay roofing tiles Masonry units Page 19 of 110 --20130510
1.35.13 1.35.14 1.35.15 1.35.16 1.35.17 1.35.18 1.35.19 water absorption of clay masonry damp proof course units by boiling in water water absorption of concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units water absorption of clay and calcium silicate masonry units by cold water absorption net volume and percentage of voids by hydrostatic weighing mass per unit volume transversal fracture load moisture movement ČSN EN 772-7 ČSN EN 772-11 ČSN EN 772-21 ČSN EN 772-3 ČSN EN 772-13 ČSN EN 1344 Annex D ČSN EN 772-14 Masonry units Masonry units Masonry units Masonry units Masonry units Clay pavers Masonry units 1.35.20 strength ČSN EN 15435 Annex A, B Precast concrete products 1.35.21 1.35.22 1.35.23 1.35.24 1.35.25 1.35.26 1.35.27 Measurement of surface dimensions and characteristics Measurement of surface dimensions and characteristics resistance to concentric load flexural strength flexural strength compressive strength in longitudinal direction compressive strength in longitudinal direction ČSN EN 15037-2+A1 p. 5.1 ČSN EN 15037-3+A1 p. 5.1 ČSN EN 15037-3+A1 p. 5.2.1 ČSN EN 15037-2+A1 p. 5.2.2 ČSN EN 15037-3+A1 p. 5.2.2 ČSN EN 15037-2+A1 p. 5.2.3 ČSN EN 15037-3+A1 p. 5.2.3 Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Beam-and-block floor systems Page 20 of 110 --20130510
1.35.28 the indirect strength ČSN EN 15037-2+A1 p. 5.2.4 Beam-and-block floor systems 1.35.29 the indirect ČSN EN 15037-3+A1 Beam-and-block floor strength p. 5.2.4 systems 1.35.30 compressive ČSN EN 772-1+A1 strength Masonry units 1.35.31 water permeability ČSN EN 491 p. 5.7 Concrete roofing tiles 1.35.32 mechanical resistance (transverse load ČSN EN 491 p. 5.6 Concrete roofing tiles bearing capacity) 1.35.33 Frost resistance test ČSN EN 491 p. 5.8 Concrete roofing tiles 1) 1.35.34 resistance to concentric load ČSN EN 15037-2+A1 p. 5.2.1 Beam-and-block floor systems Asterisk at the ordinal identifies the tests, which the Laboratory is qualified to carry out outside the permanent laboratory premises. Explanations: EOTA TR - Technical Report of the European Organization for Technical Assessment ETAG - Guideline for European Technical Approval C.D.A. - Chemical De-Icing Agents WTA - Wissenschaftliche technische Arbeitsgemeinschaft für Bauwesenverhalten und Denkmalpflege ZP - Internal Testing Procedure STN - Slovak Technical Standard Sampling: Sampling procedure name Sampling procedure identification Sampled object 1.V.1 Fresh concrete sampling ČSN EN 12 350-1 Fresh concrete sampling 1.V.2 sampling ČSN EN 12504-1 p. 2-6 samples 1.V.3 Sampling ČSN EN 13416 Bitumen, plastic and rubber sheets for roof waterproofing 1.V.4 Aggregate sampling ČSN EN 932-1 1.V.5 1.V.6 Sampling and preparation of testing mortars Sampling of cement and fly ash ČSN EN 1015-2 ČSN EN 196-7 Mortars Cement and fly ash sampling Page 21 of 110 --20130510
2. Testing Laboratory in České Budějovice 2.2 Concrete, admixtures and fibres for concrete 2.2.1* Slump test ČSN EN 12350-2 Fresh concrete 2.2.2* Flow table test ČSN EN 12 350-5 Fresh concrete 2.2.3* 2.2.4* 2.2.5 2.2.6 2.2.8 2.2.9 2.2.10* 2.2.11* 2.2.12 2.2.13 2.2.14 2.2.15 2.2.16 2.2.17 mass per unit volume air content pressure methods compressive strength of concrete tensile strength of concrete concrete frost resistance cement concrete surface resistance to water and chemical deicing agents Testing of shapes and dimensions compressive strength of concrete, including the manufacture and treatment of test specimens compressive strength of test specimens flexural strength of test specimens the indirect tensile strength of test specimens density of hardened concrete depth of penetration of water under pressure static modulus of elasticity in compression ČSN EN 12350-6 ČSN EN 12350-7 ČSN 73 1317 ČSN 73 1318 ČSN 73 1322 ČSN 73 1326, A, C method ČSN EN 12390-1 ČSN EN 12390-2 ČSN EN 12390-3 ČSN EN 12504-1 ČSN EN 12390-3 ČSN EN 12390-5 ČSN EN 12390-6 ČSN EN 12390-7 ČSN EN 12390-8 ČSN ISO 1920-10 Fresh concrete Fresh concrete Page 22 of 110 --20130510
2.2.18 2.2.19 2.2.20 2.2.22* 2.2.23* 2.2.24* 2.2.25* 2.2.26 2.2.27 2.2.28 2.2.29 2.2.37* 2.2.38* 2.2.39* 2.2.40* 2.2.41 2.2.42 moisture content, absorption power and capillarity watertightness concrete frost resistance by accelerated tests Test of compressive strength rebound by hardness drop tester Test of compressive strength by hardness testing methods (Schmidt N. L.) Testing of concrete by hardness testing methods (Schmidt N. L.) setting time bleeding of concrete capillary absorption solids content layer adhesion and tensile strength of surface layers and impermeability Measurement of pavement surface macrotexture depth using a volumetric patch technique Measurement and assessment of irregularity of pavement courses Testing of impermeability of layers by measuring their electric resistance Layer impermeability test by high-voltage (spark test) static modulus of elasticity in compression ČSN 73 1316 ČSN 73 1321 ČSN 73 1325 ČSN EN 12504-1 ČSN EN 12504-2 ČSN 73 1373 ČSN 73 2011 ČSN EN 480-2 ČSN EN 480-4 ČSN EN 480-5 ČSN EN 480-8 ČSN 73 6242 Annex B ČSN EN 13036-1 ČSN 73 6175 p. 8 ČSN 73 6242 Annex D ČSN 73 6242, Annex E ČSN ISO 6784 Concrete and mortar additives Concrete and mortar additives Concrete and mortar additives Concrete and mortar additives Bridges surfaces Bridges surfaces Bridges surfaces Bridges surfaces Bridges surfaces Page 23 of 110 --20130510
2.3 Small concrete products 2.3.1* 2.3.2* 2.3.3* 2.3.4 2.3.5 2.3.6 2.3.7 2.3.8 2.3.9 2.3.10 dimensions dimensions dimensions total water absorption total water absorption total water absorption the indirect tensile strength flexural strength and fracture load bending strength load capacity and the total bearing capacity ČSN EN 1338 Annex C ČSN EN 1339 Annex C ČSN EN 1340 Annex C ČSN EN 1338 Annex E ČSN EN 1339 Annex E ČSN EN 1340 Annex E ČSN EN 1338 Annex F ČSN EN 1339 Annex F ČSN EN 1340 Annex F ČSN EN 12839 ed. 2 2.4 Concrete building components and structures 2.4.1* 2.4.2 2.4.4* 2.4.5 2.4.6 dimensions, shapes, top layer of reinforcement, crack width water absorption dimensions, shapes, top layer of reinforcement, crack width Tests of strength and load bearing capacity Tests of strength and load bearing capacity ČSN EN 13369 Annex J ČSN EN 13369 Annex G ČSN EN 15037-1 Annex H ČSN EN 1916 Annex C, D ČSN EN 1917 Annex A, B 2.4.7* Static loading test ČSN EN 15037-1 Annex H 2.4.9 2.4.10* watertightness Measurement of dimensions a characteristics of surface, mechanical resistance ČSN EN 1917 Annex C, D ČSN EN 15037-2+A1, p. 5.1, 5.2.1, 5.2.2, 5.2.3 Elements for fences Concrete components Concrete components Concrete girders for ceiling structures Concrete pipes Concrete manholes Concrete girders for ceiling structures Concrete manholes Concrete components Page 24 of 110 --20130510
2.4.11* Measurement of accuracy ČSN 73 0212-5 Building components 2.4.12 moisture content by drying at elevated temperature ČSN EN ISO 12570 Building materials and products 2.4.13 mass ČSN 73 2045 Building components 2.5 Timber, timber components, timber based and fibre-cement products 2.5.1* Static loading tests ČSN EN 380 Timber structures 2.5.2 Testing of joints of timber structures ČSN EN 1382 EAD 040089-00-0404, p. 2.2.3.13 Timber structures 2.5.3 Soft body impact test ČSN EN 596 Timber framed walls 2.6 Physical factors 2.6.1* air permeability of buildings ČSN EN ISO 9972 2.7 Glass grids, geotextiles and geotextile-related products 2.7.1 tensile strength and elongation of mesh ČSN EN 13496 2.9 Materials, products and waterproofing systems 2.9.1 watertightness ČSN EN 14891 method A.7 2.9.2 Water absorption test ČSN 50 3602 p. 46-48 2.9.3 2.9.4 mass per unit area the crackbridging ČSN 50 3602 p. 10 and 11 ČSN EN 14891 method A.8 2.9.5 adhesion ČSN EN 14891 method A.6 2.12 Stone, aggregates, inactive concrete admixtures, soils 2.12.1 2.12.2 resistance to freezing and thawing various aggregate particles ČSN EN 1367-1 ČSN 72 1180 Buildings Glass fibre mesh Liquid-applied water impermeable products used under ceramic tiling Covering and insulation materials in rolls Covering and insulation materials in rolls Liquid-applied water impermeable products used under ceramic tiling Liquid-applied water impermeable products used under ceramic tiling Page 25 of 110 --20130510
2.12.3 2.12.4 2.12.5 2.12.6 2.12.7 2.12.8 2.12.9 2.12.11 2.12.12 2.12.13 2.12.14 2.12.15 2.12.16 2.12.17 Tests of aggregate fines Loss by drying particle size distribution Sieving analysis particle shape - Flakiness index particle shape - Shape index percentage of crushed and broken surfaces in coarse aggregate particles Assessment of fines Sand equivalent test Assessment of fines Methylene blue test Classification test for the constituents of coarse recycled aggregate resistance to wear resistance to fragmentation loose bulk density and voids the water content by drying in a ventilated oven particle density and water absorption particle density and water absorption ČSN 72 1187 ČSN EN 933-1 ČSN EN 933-3 ČSN EN 933-4 ČSN EN 933-5 ČSN EN 933-8 ČSN EN 933-9+A1 ČSN EN 933-11 ČSN EN 1097-1 ČSN EN 1097-2 ČSN EN 1097-3 ČSN EN 1097-5 ČSN EN 1097-6 ČSN EN 1097-7 2.12.18 Magnesium sulfate test ČSN EN 1367-2 2.12.19 2.12.20 2.12.21 Tests for thermal and weathering properties of aggregates boiling test drying shrinkage Testing of chemical properties of aggregates ČSN EN 1367-3 ČSN EN 1367-4 ČSN EN 1744-1+A1 p. 15.1 Page 26 of 110 --20130510
2.12.22 2.12.23 2.12.24 2.12.25 2.12.26 dense aggregate durability by accelerated test with sodium sulphate resistance of aggregates to freezing by freeze test resistance to fragmentation resistance to freezing and thawing resistance of aggregates to magnesium sulphate 2.12.28 Reserved ČSN 72 1176 method A ČSN 72 1176 method B ČSN EN 13450 Annex C ČSN EN 13450 Annex F ČSN EN 13450 Annex G resistance 2.12.29 to freezing and thawing 2.12.31* compaction of soils and backfills density 2.12.32* with cutting ring 2.12.33* compactability Proctor compaction density 2.12.34 and water absorption 2.12.35 2.12.36 2.12.37 flexural strength freeze and thaw resistance dimensions, geometric characteristics and surface quality ČSN EN 1367-7 ČSN 72 1006 ČSN 72 1010 method A ČSN EN 13286-2 ČSN EN 14617-1 ČSN EN 14617-2 ČSN EN 14617-5 ČSN EN 14617-16 Lightweight aggregates Soils and backfills Soils and backfills Soils and backfills Artificial stone Artificial stone Artificial stone Artificial stone 2.12.38* Static plate load test ČSN 73 6190 Soils and backfills 2.12.39* Impact load tests ČSN 73 6192 Soils and backfills 2.14 Metallic materials and parts in construction 2.14.1* Performance of tensile tests ČSN EN ISO 6892-1 Metallic products Page 27 of 110 --20130510
2.14.2 Bend test ČSN EN ISO 7438 Metallic products 2.14.3 Bend test ČSN EN ISO 5173 Metallic products 2.15 2.15.1 Chimneys, chimney sheaths and flues, refractory, ceramic raw materials Freeze-thaw resistance test ČSN EN 14297 Chimney products method 2.17 Mortars, mortar mixtures, renovation materials, screeds 2.17.1 Frost resistance test ČSN 72 2452 Masonry mortars 2.17.2 2.17.3 2.17.4 2.17.5 2.17.6 2.17.7 2.17.8 2.17.9 2.17.10 2.17.11 particle size distribution (by sieve analysis) consistence of fresh mortar by flow table consistence of fresh mortar (by plunger penetration) density of fresh mortar air content of fresh mortar workable life and correction time of fresh mortar dry bulk density of hardened mortar compressive strength of mortar Test of compressive strength flexural strength of mortar ČSN EN 1015-1 ČSN EN 1015-3 ČSN EN 1015-4 ČSN EN 1015-6 ČSN EN 1015-7 ČSN EN 1015-9 ČSN EN 1015-10 ČSN EN 1015-11 ČSN EN 13892-2 ČSN EN 1015-11 Dry mixtures Fresh mortar Fresh mortar Fresh mortar Fresh mortar Fresh mortar Dry mortar Dry hardened mortar Screed materials Dry hardened mortar 2.17.12 Test of flexural strength ČSN EN 13892-2 Screed materials 2.17.13* adhesion ČSN EN 1015-12 Dry hardened mortar 2.17.14 adhesion of cementitious adhesives ČSN EN 12004-2 Mortars and adhesives 2.17.15* adhesion ČSN EN 13892-8 Screed materials Page 28 of 110 --20130510
2.17.16 2.17.17 2.17.18 water absorption coefficient due to capillary action of hardened mortar water vapour permeability of surface finish of building structures the compatibility of one-coat rendering mortars with substrates ČSN EN 1015-18 ČSN EN 1015-19 ČSN EN 1015-21 Mortars Mortars Mortars 2.17.19 slip ČSN EN 12004-2 Mortars and adhesives 2.17.20 shear adhesion strength of dispersion adhesives ČSN EN 12004-2 Mortars and adhesives 2.17.21 open time ČSN EN 12004-2 Mortars and adhesives 2.17.22 2.17.23 2.17.24 2.17.25 2.17.26 2.17.27 2.17.28 transverse deformation for cementitious adhesives and grouts shear adhesion strength of reaction resin adhesives dimensional variations water retention capability water vapour diffusion resistance factor capillary water absorption water penetration depth ČSN EN 12004-2 ČSN EN 12004-2 ČSN EN 13872 WTA 2-9-04/D p. 6.2.4 WTA 2-9-04/D p. 6.3.2 WTA 2-9-04/D p. 6.3.6 WTA 2-9-04/D p. 6.3.7 Mortars and adhesives Mortars and adhesives Screed materials Renovation plasters Renovation plasters Renovation plasters Renovation plasters 2.17.29 porosity WTA 2-9-04/D p. 6.3.9 Renovation plasters 2.17.30 2.17.31 resistance of renovation plasters to salt linear shrinkage WTA 2-9-04/D p. 6.3.10 ČSN EN 12617-1 Renovation plasters Renovation materials Page 29 of 110 --20130510
2.17.32 thermal compatibility Freeze-thaw cycling with de-icing salt immersion ČSN EN 13687-1 Renovation materials 2.17.33 2.17.34 2.17.35 2.17.36 2.17.37 2.17.38 2.17.39 Freeze-thaw cycling without de-icing salt immersion shrinkage and expansion compressive strength of repair mortar resistance to capillary absorption Measurement of bond strength by pull-off coefficient of thermal expansion setting time ČSN EN 13687-3 ČSN EN 12617-4 p. 6, 7 ČSN EN 12190 ČSN EN 13057 ČSN EN 1542 ČSN EN 1770 p. 4 ČSN EN 13294 2.18 Tanks, reservoirs, septic tanks, water treatment plants 2.18.1* Water tightness test ČSN 75 0905 Tanks 2.18.2* Test of watertightness and nominal dimension 2.18.3 Test on hydraulic effectivity 2.23 Plastics and composites 2.23.1 2.23.2 2.23.3 2.23.4 water absorption of plastics tensile properties tensile properties the effects of immersion in liquid chemicals (including water) ČSN EN 12566-1, Annex A ČSN EN 12566-1:2001-1, Annex B ČSN EN ISO 62 ČSN EN ISO 527-2 ČSN EN ISO 527-3 ČSN EN ISO 175 Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Renovation materials Prefabricated septic tanks Prefabricated septic tanks Plastics Plastics Plastics Plastics 2.24 Construction cements, fly ash, slags, stabilization of soils, bitumens 2.24.1 normal consistency and setting time of cement ČSN EN 196-3 p. 1 to 6 Cement, masonry cement Page 30 of 110 --20130510
2.24.2 2.24.3 2.24.4 volume stability of cement the strength of cement bulk density ČSN EN 196-3 p. 7 ČSN EN 196-1 ČSN EN 459-2 p. 5.8 Cement, masonry cement Cement, masonry cement Lime 2.26 Gypsum and gypsum products, rock gypsum, anhydride, MgO based panels 2.26.1 2.26.2 flexural strength compressive strength ČSN EN 13279-2 p. 4.5.4 ČSN EN 13279-2 p. 4.5.5 2.26.3 adhesion ČSN EN 13279-2 p. 4.6 2.26.4 2.26.5 consistence and workable life compressive strength and flexural strength 2.26.6 ph 2.26.7 2.26.8 setting time shrinkage and expansion ČSN EN 13454-2+A1 p. 5.2 ČSN EN 13454-2+A1 p. 4.4, 5.3 ČSN EN 13454-2+A1 p. 4.2, 5.1 ČSN EN 13454-2+A1 p. 4.3 ČSN EN 13454-2+A1 p. 4.5, 5.4 Gypsum binders and gypsum plasters Gypsum binders and gypsum plasters Gypsum binders and gypsum plasters Binders, composite binders Binders, composite binders and factory made mixtures for floor screeds Binders, composite binders and factory made mixtures for floor screeds Binders, composite binders and factory made mixtures for floor screeds Binders, composite binders 2.29 Cements, adhesives, jointing materials, paints and coatings, surface finishes 2.29.1* adhesion ČSN 73 2577 Surface finish 2.29.2* 2.29.3 2.29.4 2.29.5 2.29.6 2.29.7 watertightness resistance to frost water vapour transmission properties resistance to rapid temperature changes resistance to liquids resistance to liquids ČSN 73 2578 ČSN 73 2579 ČSN 73 2580 ČSN 73 2581 ČSN EN ISO 2812-1 ČSN EN ISO 2812-2 Surface finish Surface finish Surface finish Surface finish Surface finish Surface finish Page 31 of 110 --20130510
2.29.8 Pull-off test for adhesion ČSN EN ISO 4624 Surface finish 2.29.9 2.29.10 water vapour transmission rate water permeability ČSN EN ISO 7783 ČSN EN 1062-3 Surface finish Surface finish 2.29.11 Drop weight test ČSN EN ISO 6272-1 Surface finish 2.29.12 shear strength ČSN EN 1465 Adhesives 2.29.13 Shear test ČSN EN 1373 Adhesives 2.29.14 2.29.15 2.29.16 2.29.17 2.29.18 2.29.19 2.29.20 2.29.21 2.29.22 2.29.23 2.29.24 dimensional variations dimensional changes after ageing elastic recovery resistance to flow adhesion and cohesion volume changes adhesion and cohesion at maintained extension after immersion in water adhesion and cohesion properties after immersion in water tensile properties tensile properties at maintained extension flexural and compressive strength ČSN EN 1841 ČSN EN 1903 ČSN EN ISO 7389 ČSN EN ISO 7390 ČSN EN ISO 9046 ČSN EN ISO 10563 ČSN EN ISO 10590 ČSN EN ISO 10591 ČSN EN ISO 8339 ČSN EN ISO 8340 ČSN EN 12808-3 Adhesives Adhesives Sealants Sealants Sealants Sealants Sealants Sealants Sealants Sealants Grouts for tiles 2.29.25 shrinkage ČSN EN 12808-4 Grouts for tiles 2.29.26 water absorption ČSN EN 12808-5 Grouts for tiles 2.29.27 Peel test ČSN EN 1372 Adhesives Page 32 of 110 --20130510
2.30, thermal tests 2.30.1* length and width ČSN EN 822 2.30.2* thickness ČSN EN 823 2.30.3* squareness ČSN EN 824 2.30.4* flatness ČSN EN 825 2.30.5 Pressure test ČSN EN 826 2.30.6 2.30.7 2.30.8 2.30.9 2.30.10 2.30.11 tensile strength perpendicular to faces dimensional stability under specified temperature and humidity conditions dimensional stability at constant laboratory conditions water absorption by partial immersion long term water absorption by immersion water vapour transmission rate ČSN EN 1607 ČSN EN 1604 ČSN EN 1603 ČSN EN 1609 ČSN EN 12087 method 1A, 2A ČSN EN 12086 2.30.12 Bend test ČSN EN 12089 2.30.13 2.30.15 2.30.16 mass per unit volume thermal resistance by means of guarded hot plate and heat flow meter methods steadystate thermal transmission properties ČSN EN 1602 ČSN EN 12667 ČSN EN ISO 8990 materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products Building materials Page 33 of 110 --20130510
2.30.17 2.30.18 2.30.19 2.30.20 2.30.21 2.30.22 2.30.23 2.30.24 2.30.25 2.30.26 2.30.27 2.30.28 steady state thermal resistance and related quantities Guarded hot plate apparatus steady state thermal resistance and related quantities Guarded hot plate apparatus steady state thermal resistance and related quantities Guarded hot plate apparatus steady state thermal resistance and related quantities Guarded hot plate apparatus behaviour under point load shear behaviour pressure forming setting of blown insulation initial value of thermal conductivity the accelerated aged value of thermal conductivity value of thermal conductivity fixed increment procedure setting of blown insulation 2.32 systems 2.32.1 2.32.2 adhesion to the substrate resistance to frost ISO 8302 ČSN 72 7012-1 ČSN 72 7012-2 ČSN 72 7012-3 ČSN EN 12430 ČSN EN 12090 ČSN EN 1606 ČSN EN 14064-1 ČSN EN 14315-1, C.3 ČSN EN 14315-1, C.4 ČSN EN 14315-1, C.5 ČSN EN 15101-1, method B ETAG 004 p. 5.1.4.1, 5.1.7.1 EAD 040089-00-0404, p. 2.2.3.1, 2.2.3.3, 2.2.3.4, 2.2.3.20, 2.2.3.21 ETAG 004 p. 5.1.3.2.2 EAD 040089-00-0404, p. 2.2.2.3 materials and products materials and products materials and products materials and products materials and products materials and products materials and products materials and products PUR foams PUR foams PUR foams materials and products Adhesive and screed materials for ETICS Mortars Page 34 of 110 --20130510
2.32.3 2.32.4 2.32.5 2.32.6 2.32.7 2.32.8 tensile strength and elongation of mesh Tensile test perpendicular to the faces - in wet conditions ETICS render strip tensile test water absorption impact resistance resistance to elongation 2.32.9 Static foam block test 2.32.10 mass per unit volume ETAG 004 p. 5.6.7.1 EAD 040089-00-0404, p. 2.2.3.23, 2.2.3.24, 2.2.3.25 ETAG 004 p. 5.2.4.1.2 ETAG 004 p. 5.5.4.1 EAD 040089-00-0404, p. 2.2.3.12 ETAG 004 p. 5.1.3.1 EAD 040089-00-0404, p. 2.2.2.1 ETAG 004 p. 5.1.3.3.1, 5.1.3.3.2 EAD 040089-00-0404, p. 2.2.3.19 ETAG 004 p. 5.1.4.3.1. EAD 040089-00-0404, p. 2.2.3.6.1 ETAG 004 p. 5.1.4.3.2. EAD 040089-00-0404, p. 2.2.3.6.1 ETAG 004 p. C.1.1.1 ETICS meshes ETICS insulant Screed material for ETICS ETICS ETICS ETICS ETICS Adhesive and screed materials, plasters and liquids ETICS 2.32.11 dry matter ETAG 004 p. C.1.1.2 Plasters and liquids ETICS 2.32.12 2.32.13 2.32.14 2.32.15 2.32.16 2.32.17 2.32.18 ash content water retention capability density of fresh mortar ETAG 004 p. C.1.1.3 ETAG 004 p. C.1.2.1 ETAG 004 p. C.1.2.2 shrinkage ETAG 004 p. C.1.3.1.2 of base coat Products with a thickness ETAG 004 p. C.1.3.2 up to 5 mm: static modulus EAD 040089-00-0404, of elasticity, tensile strength p. 2.2.3.16 and elongation at break mass per unit area of reinforcement ETAG 004 p. C.3.1 mesh ash content of reinforcement ETAG 004 p. C.3.2 mesh Pastes and liquids ETICS Fresh mortar ETICS Fresh mortar ETICS Base coat ETICS Base coat ETICS Mesh ETICS Mesh ETICS Page 35 of 110 --20130510
2.32.19 2.32.20 mesh size and of filaments dry bulk density of hardened mortar ETAG 004 p. C.3.3 ETAG 004 p. C.1.3 Mesh ETICS Base coat ETICS 2.32.21 grain size ETAG 004 p. C.1.1.4 Pastes, powders ETICS 2.32.22 Bracket resistance to vertical load (dead weight) ETAG 034-2 Annex E Ventilated facades 2.32.23 2.32.24 2.32.25 2.32.26 2.32.27 2.32.28 2.32.29 2.32.30 2.32.31 2.32.32 2.32.33 2.32.34 2.32.35 Bracket resistance to horizontal load (wind suction) hygrothermal behaviour Tests for foam adhesives for ETICS pullthrough resistance of cladding element pullthrough resistance under shear loads pull-out resistance pullthrough resistance under shear loads pullthrough resistance of cladding element pull-out resistance resistance to vertical load Determination pull-through resistance of cladding elements Determination pull-through resistance of cladding elements pull-out resistance ETAG 034-2 Annex E ETAG 004 p. 5.1.3.2.1 EAD 040089-00-0404, p. 2.2.2.1 EOTA TR 46 EAD 040089-00-0404, p. 2.2.3.17, 2.2.3.18 ETAG 034-1, 5.4.2.1.1 ETAG 034-1, 5.4.2.1.2 ETAG 034-1, 5.4.2.2.1 ETAG 034-1, 5.4.2.2.2 ETAG 034-1, 5.4.2.2.3 ETAG 034-1, 5.4.2.3.1 ETAG 034-1, 5.4.2.3.3 ETAG 034-1, 5.4.2.3.4 ETAG 034-1, 5.4.2.4.1 ETAG 034-1, 5.4.2.6.1 Ventilated facades ETICS Foam adhesives Ventilated facades Ventilated facades Ventilated facades Ventilated facades Ventilated facades Ventilated facades Ventilated facades Ventilated facades Ventilated facades Ventilated facades Page 36 of 110 --20130510