TECHNICAL GUIDE SPLIT-SYSTEM AIR CONDITIONERS 10 SEER R22 60Hz MODELS: H*BA-(T,W)036 THRU 076 (3 THRU 6.3 NOMINAL TONS, 3 PH) LISTED MODELS: 018-060 (3 PH) MODELS: 076 (3 PH) ISO 9001 Certified Quality Management System Due to continuous product improvement, specifications are subject to change without notice. Visit us on the web at www.york.com Additional rating information can be found at www.ari.org/aridirectory. 261645-BTG-C-0108 DESCRIPTION The 10 SEER Series condensing unit is the outdoor part of a versatile system of air conditioning. It is designed to be custom-matched with one of UPG s complete line of evaporator sections, each designed to serve a specific function. Matching Air Handlers are available for upflow, downflow or horizontal applications to provide a complete system. Electric Heaters are available if required. Add-On coils are available for use with upflow, downflow or horizontal furnaces and air handlers. WARRANTY Three Phase Units: 1-year limited parts warranty. 5-year limited compressor warranty. FEATURES QUALITY CONDENSER COILS - The coil is constructed of enhanced copper tube and aluminum fins. COIL PROTECTION - Coils are protected from damage by a polymer mesh applied between the coil face, and a PVC coated steel coil guard. PROTECTED COMPRESSOR - The compressor is internally protected against high pressure and temperature. This is accomplished by the simultaneous operation of high pressure relief valve and a temperature sensor which protects the compressor if undesirable operating conditions occur. A liquid line filter-drier further protects the compressor. DURABLE FINISH - The cabinet is made of pre-painted steel. The pre-treated flat galvanized steel provides a better paint to steel bond, which resists corrosion and rust creep. Special primer formulas and matted desert sand finish insure less fading when exposed to sunlight. LOWER INSTALLED COST - Installation time and costs are reduced by easy power and control wiring connections. Discharge line heat exchanger knockouts are provided, if required. Available in sweat connect models only. The unit contains enough refrigerant for matching indoor coils and 15 feet of interconnecting piping. The small base dimension means less space is required on the ground or roof. TOP DISCHARGE - The warm air from the top mounted fan is blown up away from the structure and any landscaping. This allows compact location on multi-unit applications. LOW OPERATING SOUND LEVEL - The upward air flow carries the normal operating noise up away from the living area. The rigid top panel effectively isolates any motor sound. Isolator mounted compressor and the rippled fins of the condenser coil muffle the normal fan motor and compressor operating sounds. LOW MAINTENANCE - Long life permanently lubricated motor-bearings need no annual servicing. EASY SERVICE ACCESS - Fully exposed refrigerant connections, a single panel covering the electrical controls and the molex plug in the control box connecting the condenser fan, make for easy servicing of the unit. SECURED SERVICE VALVES - Secured re-usable service valves are provided on both the liquid and vapor sweat connections for ease of evacuating and charging. U.L. and C.U.L. listed - approved for outdoor application. Certified in accordance with the Unitary Small Equipment certification program, which is based on ARI Standard 210/240. FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
261645-BTG-C-0108 PHYSICAL AND ELECTRICAL DATA - 3 Phase MODEL T036S T042S T048S T060S T076S W036S W042S W048S Unit Supply Voltage 208-230V, 3φ, 60Hz 460, 3φ, 60Hz Normal Voltage Range 1 187 to 252 432 to 504 W060S Minimum Circuit Ampacity 15.0 17.4 17.3 21.3 25.8 8.0 8.4 8.3 10.8 13.0 Max. Overcurrent Device Amps 2 25 30 30 35 40 15 15 15 15 20 Min. Overcurrent Device Amps 3 15 20 20 25 30 15 15 15 15 15 W076S Compressor Type Recip Recip Recip Scroll Scroll Recip Recip Recip Scroll Scroll Compressor Rated Load 10.9 12.8 11.7 16.0 18.9 5.8 6.1 6.1 8.0 9.5 Amps Locked Rotor 78 78 78 125 146 40 39 39 67 73 Crankcase Heater No No No No No No No No No No Fan Motor Amps Rated Load 1.4 1.4 1.3 1.3 2.2.8.8.7.8 1.2 Fan Diameter Inches 18 18 22 22 24 18 18 22 22 24 Rated HP 1/4 1/4 1/4 1/4 1/3 1/4 1/4 1/5 1/4 1/3 Fan Motor Nominal RPM 1,100 1,100 850 850 1100 1,100 1,100 850 850 1100 Nominal CFM 2,750 2,750 3,250 3,450 4000 2,750 2,750 3,250 3,450 4000 Face Area Sq. Ft. 9.15 12.58 15.72 23.58 18.0 9.15 12.58 15.72 23.58 18.0 Coil Rows Deep 1 1 1 1 2 1 1 1 1 2 Fin / Inches 18 18 18 18 16 18 18 18 18 16 Liquid Line OD (Field Installed) 3/8 3/8 3/8 3/8 1/2 3/8 3/8 3/8 3/8 1/2 Vapor Line OD (Field Installed) 3/4 3/4 7/8 7/8 1-1/8 3/4 3/4 7/8 7/8 1-1/8 Unit Charge (Lbs. - Oz.) 4 3-15 5-4 7-5 9-15 12-15 3-15 5-4 7-5 9-15 12-15 Charge Per Foot, Oz. 4.68.68.70.70 1.26.68.68.70.70 1.26 Operating Weight Lbs. 170 176 206 228 219 170 176 206 228 219 1. Rated in accordance with ARI Standard 110, utilization range A. 2. Dual element fuses or HACR circuit breaker. Maximum allowable overcurrent protection. 3. Dual element fuses or HACR circuit breaker. Minimum recommended overcurrent protection. 4. The Unit Charge is correct for the outdoor unit, matched indoor coil and 15 feet of refrigerant tubing. For tubing lengths other than 15 feet, add or subtract the amount of refrigerant, using the difference in length multiplied by the per foot value. DIMENSIONS A C Unit Model Dimensions (Inches) Refrigerant Connection Service Valve Size A 1 B C Liquid Vapor 036 19 35 23 3/4 042 25 35 23 3/8 048 27 37 27 7/8 060 39 37 27 076 26 43 32 1/2 1-1/8 B 1. Including Fan guard. 2 Unitary Products Group
261645-BTG-C-0108 Additional R-22 Charge / Orifice Size for Various Matched Systems - 3 Phase Outdoor Unit (T,W)036S (T,W)042S (T,W)048S (T,W)060S (T,W)076S Unit Orifice (s) 1 67, 71, 73 75, 78, 81 81 90 Factory R-22 Charge, lbs-oz 3-15 5-4 7-5 9-15 12-15 Unit Orifice (s) 2,3 Additional Charge, Oz FC/MC/PC/UC36 61 + 3 FC/MC/PC/UC42 75 + 1 FC/MC/PC/UC48 78 + 9 81 + 15 FC/MC/PC/UC60 78 + 16 90 + 5 AHP18 AHP24 AHP36 75 + 11 AHP42 75 + 11 78 + 6 AHP48 78 + 16 81 + 20 AHP60 78 + 16 90 + 5 F*FP036 61 + 5 F*FP042 75 + 1 F*FP045 78 + 14 F5FP048 75 + 9 81 + 15 F5FP060 78 + 16 90 + 5 KDBC090 0 FOOTNOTES: 1. These orifices are packed in the Customer packet of each outdoor unit. 2. Systems matched with furnace or air handlers not equipped with blower-off delays may require blower Time Delay Kit 2FD06700224. 3. PC coils cannot be used in downflow or horizontal applications. FC coils cannot be used in horizontal applications. PROCEDURES: 1. Unit factory charge listed on the unit nameplate includes refrigerant for the condenser, the smallest evaporator and 15 feet of interconnecting line tubing. 2. Verify the TXV and additional charge required for specific evaporator coil in the system using the above table. 3. Additional charge for the amount of interconnecting line tubing greater than 15 feet at the rate specified in the table above. 4. Permanently mark the unit nameplate with the total system charge. Total System Charge = Base Charge (as shipped) + adder for evaporator + adder for line set. Unitary Products Group 3
261645-BTG-C-0108 COOLING CAPACITY - With Air Handler Coils AIR HANDLER UNIT MODEL MODEL W (T,W)036S (T,W)042S (T,W)048S COIL MODEL 1 3 PH 10 SEER AC WITH MA RATED CFM TOTAL NET MBH COOLING SENS. 1. MC coils available with a factory installed horizontal drain pan. See price pages for specific model number. = Not applicable. SEER MA12B 17 FC / MC30B 1200 33.6 24.9 10.00 9.10 MA12B 17 FC / MC36B 1200 33.8 25.0 10.00 9.20 MA12B 17 FC / MC42B 1200 34.4 25.5 10.15 9.30 MA16C 21 FC / MC42C 1380 40.0 30.2 10.00 9.05 MA16C 21 FC / MC48C 1450 41.0 30.3 10.10 9.15 MA14D 24 FC / MC48D 1450 41.0 30.3 10.10 9.15 MA16C 21 FC60C 1450 42.0 31.0 10.10 9.50 MA14D 24 FC / MC60D 1450 42.0 31.0 10.10 9.50 MA16C 21 FC / MC48C 1600 46.0 34.0 10.10 9.50 MA20D 24 FC / MC48D 1600 46.0 34.0 10.10 9.50 MA16C 21 FC60C 1600 47.0 34.0 10.40 9.70 MA20D 24 FC / MC60D 1600 47.0 34.0 10.40 9.70 (T,W)060S MA20D 24 FC / MC60D 1750 58.5 39.8 10.00 10.25 (T,W)036S (T,W)042S (T,W)048S (T,W)060S 3 PH 10 SEER AC WITH AHP/SHP AHP36 17 1235 35.0 24.2 10.30 11.00 F*FP036 24 1200 34.4 35.2 10.20 9.30 F*FP042 21 1200 34.4 25.2 10.15 9.20 AHP42 21 1400 40.0 30.0 10.00 9.20 F*FP042 21 1400 39.5 28.9 10.00 9.00 F5FP048 24 1400 40.5 30.0 10.00 9.20 AHP/SHP48 24 1600 47.0 34.4 10.40 9.70 AHP/SHP60 24 1600 47.0 34.4 10.40 9.70 F5FP048 24 1600 45.5 33.7 10.00 9.15 F5FP060 24 1600 46.5 34.4 10.00 9.70 AHP/SHP60 24 1750 58.5 39.8 10.00 9.80 F5FP060 24 1750 58.5 39.8 10.00 9.80 (T,W)076S K4EU090 22 2600 73.5 10.00 Rated in accordance with DOE test procedures (Federal Register 12-27-79 and 3-18-88) and ARI Standards 210. Cooling MBH based on 80 F entering air temperature, 50% RH, and rated air flow. EER (Energy Efficiency Ratio) is the total cooling output in BTU s at 95 F outdoor ambient divided by the total electric power in watt-hours at those conditions. SEER (Seasonal Energy Efficiency Ratio) is the total cooling output in BTU s during a normal annual usage period for cooling divided by the total electric power input in watt-hours during the same period. EER 4 Unitary Products Group
COOLING CAPACITY - Upflow, Downflow & Horizontal Furnaces and Coils FURNACE** COOLING COIL UNIT MODEL CFM RANGE MODEL RATED NET MBH W (MIN.-MAX.) CFM TOTAL SENS. (T,W)036S (T,W)042S (T,W)048S (T,W)060S 1050 1350 1225 1575 1400 1800 1525 1975 261645-BTG-C-0108 SEER 1 17 FC/MC/PC/UC30B 1200 33.6 24.9 10.00 9.10 17 FC/MC/PC/UC36B 1200 33.8 25.0 10.00 9.20 17 FC/MC/PC/UC42B 1200 34.4 25.5 10.15 9.30 14 HC30 1200 33.8 25.0 10.00 9.20 17 HC36 1200 34.4 25.5 10.15 9.30 HD36 1200 34.8 25.8 10.00 8.95 21 FC/MC/PC/UC42C 1380 40.0 30.2 10.00 9.05 21 FC/MC/PC/UC48C 1450 41.0 30.3 10.10 9.15 24 FC/MC/PC/UC48D 1450 41.0 30.3 10.10 9.15 21 FC/MC/PC/UC60C 1450 42.0 31.0 10.10 9.50 24 FC/MC/PC/UC60D 1450 42.0 31.0 10.10 9.50 17 HC36 1380 40.0 30.2 10.00 9.05 21 HC42 1400 41.0 30.3 10.00 9.25 24 HC60 1450 42.0 31.0 10.10 9.50 HD36 1390 40.5 30.0 10.00 9.05 21 FC/MC/PC/UC42C 1500 44.5 32.9 10.00 9.15 21 FC/MC/PC/UC48C 1600 46.0 34.0 10.10 9.50 24 FC/MC/PC/UC48D 1600 46.0 34.0 10.10 9.50 21 FC/MC/PC/UC60C 1600 47.0 34.0 10.40 9.70 24 FC/MC/PC/UC60D 1600 47.0 34.0 10.40 9.70 21 HC48 1600 45.5 33.7 10.00 9.45 24 HC60 1600 47.0 34.0 10.40 9.70 HD36 1600 45.5 33.7 10.00 9.50 HD48 1600 46.5 34.4 10.20 9.65 24 FC/MC/PC/UC60D 1750 58.5 39.8 10.00 10.25 24 HC60 1750 58.5 39.8 10.00 10.25 HD48 1750 58.5 39.8 10.00 10.25 (T,W)076S 2500-3000 35 G2FD090(S,H)35** 3200 73.5 52.9 10.00 1. Requires a 2FD06700224 Blower Time Delay unless a standard furnace is equipped with one. ** Refer to Quick Selection Chart for specific furnace match-up. EER Unitary Products Group 5
261645-BTG-C-0108 ACCESSORIES *Refer to Price Manual for specific model numbers. HARD START KIT - Provides increased starting torque for areas with low voltage. COMPRESSOR BLANKET - Designed to further reduce the normal compressor operating sound. Refer to price pages for specific match-ups. OFF CYCLE TIMER DELAY - Provides a 5-minute off cycle to prevent rapid recycling of the compressor. ROOM THERMOSTATS - A wide selection of compatible thermostats are available to provide optimum performance and features for any installation. 1H/1C, manual change-over electronic non-programmable thermostat. 1H/1C, auto/manual changeover, electronic programmable, deluxe 7-day, thermostat. 1H/1C, auto/manual changeover, electronic programmable. * For the most current accessory information, refer to the price book or consult factory. SOUND POWER RATINGS* UNIT MODEL (dba) 036 82 042 82 048 82 060 80 076 85 * Rated in accordance with ARI 270-95 Standards. TYPICAL INSTALLATION 60 OVERHEAD CLEARANCE 10 CLEARANCE COIL AREA MINIMUM 24 SERVICE ACCESS CLEARANCE ON ONE SIDE WEATHERPROOF DISCONNECT SWITCH THERMOSTAT TO FURNACE OR AIR HANDLER TERMINAL BLOCK NEC CLASS 1 WIRING NEC CLASS 2 WIRING TO INDOOR COIL NOTE: ALL OUTDOOR WIRING MUST BE WEATHERPROOF. SEAL OPENING(S) WITH PERMAGUM OR EQUIVALENT CONTROL ACCESS PANEL TYPICAL FIELD WIRING - 3 Phase Application ALL FIELD WIRING TO BE IN ACCORDANCE WITH ELECTRIC CODE (NEC) AND/OR LOCAL CODES POWER WIRING 208/230-3-60 460-3-60 24 VOLT CONTROL WIRING MINIMUM 18 GA. WIRE (NEC CLASS 2) POWER WIRING CONTROL WIRING FACTORY WIRING FURNACE OR AIR HANDLER TERMINAL BLOCK GND. LUG CONTACTOR TERMINALS COIL * TERMINAL W IS ONLY REQUIRED ON SYSTEMS WITH HEAT. C Y R G W * Y R G W CONDENSING UNIT ROOM THERMOSTAT ALL OUTDOOR WIRING MUST BE WEATHERPROOF. USE COPPER CONDUCTORS ONLY. 6 Unitary Products Group
COOLING PERFORMANCE DATA Multipliers for determining the performance with other indoor sections. 261645-BTG-C-0108 AIR CONDITIONER MODEL NO. (T,W)036S INDOOR COIL MODEL NO. FC/MC/PC/UC30 CONDENSER ID CFM 1150 1250 1350 ENTERING AIR ID DB ( F) 85 80 70 85 80 70 85 80 70 TEMPERATURE ID WB ( F) 72 67 57 72 67 57 72 67 57 T.C. 38.3 36.1 34.4 37.9 36.3 34.6 38.0 36.4 34.9 75 S.C. 24.0 23.7 24.0 24.1 24.5 24.7 24.7 25.3 25.2 K.W 3.19 3.14 3.09 3.23 3.20 3.14 3.26 3.23 3.18 T.C. 36.9 34.6 32.2 36.9 34.9 32.6 37.0 35.2 33.0 85 S.C. 24.2 23.7 22.9 24.7 24.6 23.9 25.3 25.5 24.8 K.W 3.45 3.39 3.30 3.50 3.44 3.36 3.53 3.49 3.40 T.C. 35.5 33.2 30.0 35.8 33.6 30.4 36.0 34.0 31.0 95 S.C. 24.3 23.6 21.9 25.4 24.9 23.6 26.0 25.6 24.4 K.W 3.71 3.63 3.52 3.76 3.69 3.58 3.80 3.75 3.62 T.C. 33.2 30.4 26.7 33.4 30.8 27.2 33.6 31.3 27.7 105 S.C. 23.7 22.5 20.7 24.5 23.6 21.9 25.4 24.6 23.0 K.W 3.97 3.84 3.71 4.02 3.91 3.77 4.06 3.96 3.81 T.C. 31.0 27.6 23.5 31.1 28.2 24.2 31.3 28.5 24.4 115 S.C. 23.1 21.3 19.6 23.9 22.6 20.7 24.8 23.7 21.6 K.W 4.22 4.06 3.90 4.29 4.13 3.94 4.33 4.18 4.00 T.C. 28.7 24.8 20.2 28.9 25.6 21.1 29.0 25.7 21.0 125 S.C. 22.5 20.2 18.4 23.2 21.6 19.6 24.2 22.7 20.2 K.W 4.47 4.28 4.09 4.56 4.35 4.11 4.60 4.40 4.19 NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature. Air Handler Coil T.C. S.C. KW MA12B FC/MC30B 1.00 1.00 1.00 MA12B FC/MC36B 1.01 1.00 0.99 MA12B FC/MC42B 1.02 1.02 0.98 AHP36 1.04 0.97 0.83 F*FP036 1.02 1.41 0.98 F*FP042 1.02 1.01 0.99 FC/MC/PC/UC36 1.01 1.00 0.99 FC/MC/PC/UC42 1.02 1.02 0.98 HC30 1.01 1.00 0.99 HC36 1.02 1.02 0.98 HD24 1.02 1.02 1.02 HD36 1.04 1.04 1.02 Unitary Products Group 7
261645-BTG-C-0108 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. (T,W)042S INDOOR COIL MODEL NO. FC/MC/PC/UC42 CONDENSER ID CFM 1200 1400 1600 ENTERING AIR ID DB ( F) 85 80 70 85 80 70 85 80 70 TEMPERATURE ID WB ( F) 72 67 57 72 67 57 72 67 57 T.C. 47.2 44.1 41.2 47.5 44.6 41.9 47.9 45.1 42.6 75 S.C. 30.2 29.6 29.4 31.9 31.1 31.0 33.6 32.6 32.6 K.W 3.90 3.85 3.78 4.05 3.99 3.94 4.19 4.14 4.09 T.C. 45.5 42.1 38.5 45.9 42.8 39.3 46.3 43.4 40.2 85 S.C. 29.8 28.9 28.1 31.4 30.7 30.0 33.0 32.5 31.9 K.W 4.13 4.06 3.96 4.28 4.21 4.13 4.43 4.36 4.29 T.C. 43.9 40.2 35.7 44.3 41.0 36.8 44.8 41.8 37.8 95 S.C. 29.5 28.2 26.9 30.9 30.3 29.1 32.4 32.4 31.2 K.W 4.36 4.27 4.14 4.52 4.43 4.31 4.67 4.59 4.49 T.C. 40.5 36.3 32.0 41.2 37.1 32.8 42.0 38.0 33.7 105 S.C. 28.1 26.7 25.1 29.9 28.8 27.2 31.7 30.9 29.3 K.W 4.58 4.44 4.30 4.74 4.60 4.47 4.89 4.77 4.64 T.C. 37.1 32.3 28.3 38.2 33.3 28.9 39.2 34.2 29.6 115 S.C. 26.8 25.1 23.3 29.0 27.2 25.4 31.1 29.4 27.4 K.W 4.81 4.62 4.45 4.96 4.78 4.62 5.10 4.95 4.79 T.C. 33.7 28.4 24.5 35.1 29.4 25.0 36.4 30.4 25.4 125 S.C. 25.5 23.5 21.5 28.0 25.7 23.5 30.5 27.9 25.5 K.W 5.04 4.79 4.61 5.18 4.96 4.78 5.32 5.13 4.94 NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature. Air Handler Coil T.C. S.C. KW MA16C FC/MC42C 0.98 1.00 1.02 MA16C FC/MC48C 1.00 1.00 1.01 MA14D FC/MC48D 1.00 1.00 1.01 MA14D FC/MC60D 1.02 1.02 0.97 MA16C FC60C 1.02 1.02 0.97 AHP42 0.98 0.99 1.01 F*FP042 0.96 0.95 1.03 F5FP048 0.99 0.99 1.01 FC/MC/PC/UC48 1.00 1.00 1.01 FC/MC/PC/UC48 1.00 1.00 1.01 FC/MC/PC/UC60 1.02 1.02 0.97 FC/MC/PC/UC60 1.02 1.02 0.97 HC36 0.98 1.00 1.02 HC42 1.00 1.00 1.00 HC60 1.02 1.02 0.97 HD36 0.99 0.99 1.02 8 Unitary Products Group
COOLING PERFORMANCE DATA Multipliers for determining the performance with other indoor sections. 261645-BTG-C-0108 AIR CONDITIONER MODEL NO. (T,W)048S INDOOR COIL MODEL NO. FC/MC/PC/UC42 CONDENSER ID CFM 1200 1400 1600 ENTERING AIR ID DB ( F) 85 80 75 70 85 80 75 70 85 80 75 70 TEMPERATURE ID WB ( F) 72 67 62 57 72 67 62 57 72 67 62 57 T.C. 53.4 48.9 45.1 40.2 54.3 49.8 45.9 41.3 54.9 50.3 46.4 41.8 75 S.C. 32.2 32.3 31.0 32.5 34.0 34.0 32.7 34.7 35.2 35.3 33.9 35.9 K.W 4.32 4.15 4.00 3.83 4.44 4.26 4.11 3.95 4.53 4.36 4.21 4.04 T.C. 52.0 47.5 43.7 39.2 52.7 48.3 44.5 40.0 53.2 48.7 45.2 40.5 85 S.C. 32.2 32.3 31.1 32.7 34.1 34.1 32.8 34.7 35.4 35.5 34.5 36.0 K.W 4.62 4.43 4.26 4.07 4.74 4.55 4.38 4.18 4.84 4.65 4.48 4.28 T.C. 49.0 44.9 41.3 36.9 49.6 45.5 42.0 37.6 50.0 45.8 42.4 38.3 95 S.C. 31.6 31.6 30.4 31.8 33.5 33.7 32.4 33.8 34.9 35.0 33.7 35.6 K.W 4.91 4.70 4.51 4.31 5.02 4.81 4.64 4.43 5.13 4.92 4.74 4.53 T.C. 45.6 41.6 38.4 34.3 46.0 42.2 39.0 35.0 46.2 42.5 39.3 36.2 105 S.C. 30.5 30.6 29.5 30.9 32.6 32.8 31.5 32.8 34.1 34.2 32.7 34.5 K.W 5.18 4.96 4.76 4.54 5.30 5.07 4.88 4.67 5.39 5.18 4.99 4.83 T.C. 41.8 38.3 35.3 31.7 42.3 38.8 35.8 33.0 42.5 39.0 36.2 33.5 115 S.C. 29.3 29.5 28.2 29.6 31.6 31.4 30.1 31.5 33.0 32.9 31.5 32.0 K.W 5.42 5.18 4.98 4.76 5.52 5.31 5.10 4.94 5.63 5.41 5.21 5.06 T.C. 38.0 35.0 32.3 29.1 38.6 35.4 32.7 31.0 38.8 35.5 33.2 30.8 125 S.C. 28.1 28.4 26.9 28.3 30.6 30.0 28.7 30.2 31.9 31.6 30.4 29.5 K.W 5.66 5.40 5.20 4.98 5.74 5.55 5.32 5.21 5.87 5.64 5.43 5.29 NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature. Air Handler Coil T.C. S.C. KW MA16C FC / MC42C 0.97 0.97 1.04 MA16C FC / MC48C 1.00 1.00 1.00 MA20D FC / MC48D 1.00 1.00 1.00 MA20D FC / MC60D 1.02 1.00 0.98 MA16C FC60C 1.02 1.00 0.98 AHP / SHP48 1.02 1.01 0.98 AHP / SHP60 1.02 1.01 0.98 F5FP048 0.99 0.99 1.04 F5FP060 1.01 1.01 0.98 FC/MC/PC/UC48 1.00 1.00 1.00 FC/MC/PC/UC48 1.00 1.00 1.00 FC/MC/PC/UC60 1.02 1.00 0.98 FC/MC/PC/UC60 1.02 1.00 0.98 HC48 0.99 0.99 1.01 HC60 1.02 1.00 0.98 HD36 0.99 0.99 1.00 HD48 1.01 1.01 0.98 Unitary Products Group 9
261645-BTG-C-0108 COOLING PERFORMANCE DATA AIR CONDITIONER MODEL NO. (T,W)060S INDOOR COIL MODEL NO. FC/MC/PC/UC60 CONDENSER ID CFM 1450 1700 1950 ENTERING AIR ID DB ( F) 85 80 70 85 80 70 85 80 70 TEMPERATURE ID WB ( F) 72 67 57 72 67 57 72 67 57 T.C. 61.2 58.5 56.3 61.8 59.1 56.9 62.3 59.6 57.5 75 S.C. 37.6 37.4 37.1 40.1 39.9 39.5 42.5 42.3 41.8 K.W 4.66 4.57 4.51 4.67 4.58 4.53 4.68 4.58 4.55 T.C. 60.6 58.0 55.0 61.2 58.6 55.8 61.9 59.3 56.7 85 S.C. 37.6 37.3 36.5 40.2 39.9 39.1 42.8 42.5 41.7 K.W 5.26 5.13 5.08 5.27 5.14 5.10 5.28 5.15 5.11 T.C. 60.0 57.4 53.7 60.7 58.5 54.8 61.4 59.0 55.8 95 S.C. 37.5 37.1 35.9 40.3 39.8 38.8 43.1 42.6 41.6 K.W 5.86 5.70 5.65 5.87 5.71 5.67 5.88 5.72 5.68 T.C. 58.1 54.6 50.0 58.9 55.7 51.3 59.7 56.8 52.7 105 S.C. 36.9 36.0 34.4 39.8 39.0 37.3 42.7 41.9 40.2 K.W 6.54 6.39 6.29 6.56 6.42 6.30 6.57 6.45 6.32 T.C. 56.2 51.8 46.3 57.1 53.2 47.9 57.9 54.5 49.5 115 S.C. 36.2 34.9 32.9 39.3 38.1 35.9 42.3 41.2 38.8 K.W 7.23 7.07 6.92 7.25 7.12 6.94 7.26 7.17 6.97 T.C. 54.3 49.0 42.6 55.2 50.6 44.5 56.2 52.3 46.4 125 S.C. 35.6 33.8 31.4 38.7 37.2 34.4 41.9 40.5 37.4 K.W 7.92 7.76 7.55 7.94 7.83 7.58 7.96 7.90 7.62 Multipliers for determining the performance with other indoor sections. NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature. Air Handler Coil T.C. S.C. KW MA20D FC / MC60D 1.00 1.00 1.00 AHP / SHP60 1.01 1.02 1.02 F5FP060 1.00 1.02 1.02 HC60 1.00 1.00 1.00 HD48 0.99 1.00 1.02 10 Unitary Products Group
COOLING PERFORMANCE DATA Multipliers for determining the performance with other indoor sections. 261645-BTG-C-0108 AIR CONDITIONER MODEL NO. (T,W)076S INDOOR COIL MODEL NO. KDBC-S090 CONDENSER ID CFM 2100 2600 3100 ENTERING AIR ID DB ( F) 85 80 70 85 80 70 85 80 70 TEMPERATURE ID WB ( F) 72 67 57 72 67 57 72 67 57 T.C. 79.1 76.3 73.9 82.0 79.2 76.9 84.9 82.0 79.9 75 S.C. 48.8 48.6 48.1 55.4 55.3 54.7 62.0 61.9 61.3 K.W 5.98 5.90 5.84 6.28 6.18 6.15 6.58 6.48 6.46 T.C. 76.4 73.7 70.6 79.1 76.3 73.4 81.7 79.0 76.2 85 S.C. 47.9 47.6 46.8 54.7 54.4 53.5 61.5 61.2 60.3 K.W 6.53 6.42 6.37 6.86 6.74 6.70 7.18 7.07 7.04 T.C. 73.8 71.1 67.2 76.1 73.5 69.9 78.4 75.9 72.6 95 S.C. 47.1 46.7 45.4 54.0 53.6 52.4 60.9 60.4 59.4 K.W 7.08 6.94 6.90 7.43 7.30 7.26 7.79 7.65 7.61 T.C. 71.1 67.4 62.6 73.1 69.7 65.2 75.1 72.0 67.7 105 S.C. 46.4 45.4 43.7 53.1 52.2 50.5 59.8 58.9 57.2 K.W 7.84 7.70 7.61 8.21 8.08 7.99 8.57 8.46 8.36 T.C. 68.4 63.7 58.0 70.0 67.0 60.4 71.7 68.2 62.9 115 S.C. 45.4 44.1 42.0 52.0 51.9 48.5 58.6 57.5 55.0 K.W 8.59 8.46 8.32 8.97 8.80 8.71 9.36 9.28 9.10 T.C. 65.6 60.1 53.4 67.0 64.3 55.7 68.4 64.3 58.1 125 S.C. 44.5 42.7 40.2 51.0 51.6 46.5 57.5 56.0 52.8 K.W 9.35 9.21 9.02 9.74 9.51 9.43 10.14 10.09 9.84 NOTE: ALL CAPACITIES ARE NET WITH INDOOR FAN HEAT ALREADY DEDUCTED AT 1250 BTUH/1000 CFM. NOTE: For dry bulb temperatures different than those listed (between 73-87 F), sensible capacity increases by 1060 BTUH per 1000 CFM per degree above the listed temperature and decreases by 1060 BTUH per 1000 CFM per degree below the listed temperature. Coil T.C. S.C. KW G2FD090(S,H)35 1.00 0.99 1.01 Unitary Products Group 11
Subject to change without notice. Printed in U.S.A. 261645-BTG-C-0108 Copyright by Unitary Products Group 2008. All rights reserved. Supersedes: 261645-BTG-B-0706 Unitary 5005 Norman Products York OK Group Drive 73069