wwwicecompanies.com Operator & Parts Manual 75 RPM Floor Machine ip7 ip0 3003 REV.0(0-09) INTELLIGENT CLEANING EQUIPMENT
READ OPERATOR MANUAL CAREFULLY IMPORTANT:To ensure full warranty protection,please fill out & return your warranty card. Please fill out at time of installation for future reference. Model No. Serial No. Machine Options Sales Rep. Sales Rep. phone no. Customer ID Number Installation Date HOW TO ORDER PARTS Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered online,by phone, by fax or by mail.. Identify the machine model.. Identify the machine serial number from the data label. 3. Ensure the proper serial number is used from the parts list.. Identify the part number and quantity. Do not order by page or reference numbers. 5. Provide your name, company name, customer ID number,billing and shipping address, phone number and purchase order number. PROTECT THE ENVIRONMENT Please dispose of packaging materials,old machine components such as batteries, hazardous fluids, including antifreeze and oil, in an environmentally safe way according to local waste disposal regulations. Always remember to recycle. ICE Company Limited XiangShi Road LiaoBu DongGuan GuangDong China Tel:0769-886 9000 Fax:0769-886 3000 Specifications and parts are subject to change without notice. ICE ip7 ip0
TABLE OF CONTENTS SAFETY PRECAUTIONS.............................. MACHINE COMPONENTS............................. 5 MACHINE OPERATING INSTRUCTIONS..................6 MACHINE MAINTENANCE & STORAGE.................. 6 HANDLE RELEASE ASSEMBLY INSTRUCTIONS........... 7 PARTS LIST...................................... 8-3 WEAR & TEAR PARTS LIST............................3 SOLUTION TANK ASSEMBLY(OPYIONAL ).............-5 SPECIFICATIONS................................... 6 WIRING DIAGRAM.................................. 6 ICE ip7 ip0
OPERATOR SAFETY PRECAUTIONS Carefully read and understand this manual before operating this machine. This machine must be grounded! This floor/finishing machine shall be grounded while in use to protect theoperator from electric shock.grounding provides a path of least resistance for electric current. This machine is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. Do not remove the ground pin under any circumstances. This machine is for use on a nominal 0-volt circuit and has a grounding plug that resembles the plug illustrated in Figure. Make sure that the machine is connected to an outlet having the same configuration as the plug. No adapter should be used with this machine. This machine is intended for commercial use. It is constructed for use in an indoor environment and is nor intended for any other use. Use only recommended accessories.. Do not operate machine: Unless trained and authorized. Unless you have read and In flammable or explosive areas. understand the operators manual. With a damaged cord or plug With the use of extension cords. If not in proper operating condition. In outdoor areas and standing water.. Before operating machine: Make sure all safety devices are in place and operating properly. 3. When using machine: Do not run machine over cord. Do not pull machine by cord or plug. Do not pull cord around Do not unplug by pulling on the cord. sharp edges or corners. Do not stretch cord. Do not handle plug with wet hands. Keep cord away from heated surfaces. Report machine damage or faulty operation immediately. When moving, repairing and tilting the machine, make sure the safety installation is right place and tighten the release handle.. Before leaving or servicing machine: Turn off machine. Unplug cord from outlet. 5. When servicing machine: Unplug cord from outlet. Use manufacturer supplied or approved replacement parts. To avoid electrical shock,please replace the power cord immediately if any damage is being detected. The replacement must be performed only by an authorized person or by our customer service center. ICE ip7 ip0
OPERATOR MACHINE COMPONENTS Machine Description Machine Structure New structure design 7" 0r 0" Deck alumiunm 6" or 9" Pad Driver Triple Planetary All Steel Gear Box Universal Clutch Plate Safety Lock-Out Switch Security protection in an upright 50' Cord 66-Frame Motor. Deck. Wheel 3. Safety installation. Level Solution 5. Trigger 6. Safety Lock-Out Switch 7. Housing 8. Handle Release Assy 9. Top Cover 0. Motor. Clutch Plate ICE ip7 ip0
OPERATOR General Use: FLOOR MACHINE OPERATING INSTRUCTIONS ) Remove any obstructions or other obstacles in the area which is to be cleaned. ) Make sure the safety installation is right place and tighten the release handle. 3) Place handle in upright position and tilt machine back until handle rests on the floor. Be sure the machine is not plugged into an outlet. ) Remove the pad center gripping device by unscrewing the thumbscrews. 5) Place appropriate burnishing pad on pad driver and re-attach the center gripping device. 6) Place machine back into its upright position. 7) Plug power cord into grounded outlet. Do not use an extension cord in conjunction with the standard power cord. 8) Release the compression handle and adjust handle height to a comfortable operating position, then push back down on the compression handle to lock the handle in operating position. 9)To start the machine, push on the Blue safety button of the top of upper switch housing and squeeze either of the switch levers. 0) When the machine is in operation, both hands should be placed on the handle (switch housing). )To stop the machine at any time, simply release the switch lever, and the machine will stop automatically. MAINTENANCE To keep the machine performing well for many years, please follow the following maintenance procedures. Always confirm that the machine is unplugged prior to performing any maintenance or repairs.. Unplug machine as soon as you are done using it.. Make sure the safety installation is right place and tighten the release handle. 3. Tilt machine back and remove pad driver or brush. Never store a low speed machine with the pad driver or brush mounted to the machine.. Clean the outside of the machine with a mild cleaner. 5. Check power cord for any damage.if damage is detected, replacepower cord immediately. 6. Lubricate wheels with a water resistant lubricant once a month. 7. Check machine for loose or missing nuts and bolts, and replace as necessary. 8. If the machine is used in a dusty environment, you may remove themotor cover and blow the motor clean with compressed air. This willensure proper ventilation, and allowthe motor to run cooler. STORAGE ) Unplug machine from power source and wrap cord on handle. ) Tilt machine back and remove pad driver or brush. 3) Store in upright position in a dry area. ICE ip7 ip0
OPERATOR HANDLE RELEASE ASSEMBLY INSTRUCTIONS Step ) Assemble handle and handle release assembly: According to in the following photos direction assembly. ) Adjust the nylon lock nut: It don't over tighten nylon lock nut, only tighten it enough to hold handle in place when compression lever is in down position. Step 3 ) Connect power cords together Step ) Take out the handle assembly, nut lock M, hex. socket head Mx0. ) After Aligning them, and use spanner to tighten them. 7 ICE ip7 ip0
PARTS LIST ip7 & ip0 HANDLE ASSEMBLY ICE ip7 ip0 8
ip7 & ip0 HANDLE ASSEMBLY DIA PART NO DESCRIPTION NO NUMBER REQ'D 0855 SCREW M8X55 333 BRACKET 3 300 TUBING 30 NUT LOCK M0 5 00 WASHER PLAIN Ø0.5XØ0X 6 380 NUT LOCK M8 7 86 WASHER PLAIN Ø8XØ6.5X.0 8 330 HOOK CABLE 9 0003 CLAMP TANK 0 550 SCREW M5 X 0 HEX SOCKET 0030 CORD POWER SUPPLY 3500 TOOTH WASHER Ø5 3 5 SCREW M5X SCREW MX 5 0030 STRAIN RELIEF CORD 6 300 TOOTH WASHER Ø 7 003 PIN 3 8 0033 LEFT TRIGGER SWITCH 9 00305 LEVEL SOLUTION 0 003 REAR COVER 66 WASHER PLAIN Ø6 5635 SCREW M6 X 35 3 565 SCREW M6 X 5 0005 SERIAL NUMBER[iP7] 0033U SERIAL NUMBER[iP0] 5 503009 CIRCUIT BREAKER 0A 6 30008 COVER 7 0037 BALL BASE 8 08 SCREW MX8 9 00330 RIGHT TRIGGER SWITCH 30 35 SCREW M3X5 3 3300 TOOTH WASHER 3 0033 SPRING SAFETY 33 00308 SWITCH 3 00307 SAFETY BOTTOM 35 00333 SAFETY SPRING 36 0030 FRONT COVER 37 0036 ICE LOGO 38 003 CLAMP CORE 9 ICE ip7 ip0
ip7 & ip0 HANDLE ASSEMBLY 39 06 SCREW MX6 0 03860 SCREW M8X60 33 HANDLE RELEASE 6785 PIN Ø8X5 3 330 VOLT HANDLE RELEASE 3303 WASHER PLAIN HANDLE RELEASE 5 330 COVER HOOK HANDLE 6 005 CORD HANDLE 7 000 PLUG PROTECTOR COVER 8 003 GROMMET 9 63003 WASHER NYLON PLAIN Ø8 ICE ip7 ip0 0
PARTS LIST ip7 & ip0 BASE ASSEMBLY ICE ip7 ip0
ip7 & ip0 BASE GROUP DIA PART NO DESCRIPTION NO NUMBER REQ'D 000 BUMPER 7" [ip7] 000 BUMPER 0" [ip0] 50 WASHER PLAIN Ø5 3 5 SCREW M5X PH 000 FRAME 7" [ip7] 000 FRAME 0" [ip0] 5 5 SCREW M5X PH 5 6 006 BARB HOSE 7 35 NUT LOCK M 8 53608 SCREW M6 X 8 9 68 WASHER PLAIN Ø6.XØ8X.6 0 00 SCREW M6 X.7 06 WHEEL 5" 350 WASHER LOCK Ø 3 65 WASHER Ø.5XØ5X.5 3307 BRACKET LEFT 5 3030 ALUMMINIUM BASE MOTOR 6 3030 AXLE 7 3308 BRACKET RIGTH 8 008 PLUG PROTECTOR 9 0800 MOTOR WITH GEAR BOX 0 005 READ MANUAL LABEL 000 COVER MOTOR 0003 COVER TOP 3 0036 LOGO ICE 08 STATIONARY SWITCH 5 083 CENTRIFUGAL SWITCH 6 080 MOTOR 0V 7 0803 BOLT WITH WASHER KIT 8 080 START-UP CAPACITOR(BIG) 60-530μF/300V 9 08 COVER CAPACITOR 30 09 SCREW 8-3UNCX0 3 0803 MOTOR LABEL 3 5 HEX SOCKET HEAD M X 0 33 080 RUNNING CAPACITOR 60μF/50V ICE ip7 ip0
ip7 & ip0 BASE GROUP DIA PART NO DESCRIPTION NO NUMBER REQ'D 3 53530 SCREW 0-3X5. 6 35 080 BIG WASHER 36 0805 RING GUARD 37 0806 COULPING 38 0807 SLEEVE 39 0809 GEAR BOX 0 8 WASHER PLAIN Ø8 8 WASHER LOCK Ø8 0855 SCREW M8X55 3 90006 6"PAD HOLDER ASSY [ip7] 90009 9"PAD HOLDER ASSY [ip0] WEAR & TEAR PARTS LIST DIA NO PART NUMBER DESCRIPTION NO REQ'D MACHINE 06 WHEEL 5" ip7&ip0 90009 9"PAD HOLDER ASSY ip0 90006 6"PAD HOLDER ASSY ip7 3 ICE ip7 ip0
DIA NO PART NUMBER ip7 & ip0 SOLUTION TANK ASSEMBLY DESCRIPTION NO REQ'D 05000U SOLUTION TANK ASSEMBLY(OPTIONAL) 003 CHAIN 3 009 SEAT,CHAIN 00 SCREW,M5,BRASS 5 008 SEAL,TANK 6 000 KNOB,M5X0 7 007 UPPER PULLING ROD BRASS 8 008 VALVE ASSEMBLY 9 009 SEAL 0 006 NUT,/-0UNF 005 BARB,HOSE,SOLUTION 0006 BARB HOSE 3 550 SCREW,M5X0,HEX SOCKET 0003 CLAMP,TANK 5 3507 NUT,LOCK,M5 6 000 CLAMP,HOOK 7 000 TANK ICE ip7 ip0 5
OPERATOR SPECIFICATION Model ip7 ip0 Voltage 0 V 0 V Power.5HP.5HP Current 3 A 3 A Frequency 60 Hz 60 Hz Speed 75 rpm 75 rpm Deck Size 7" (3 cm) 0" (50 cm) Length of power cord 5 m 5 m Weight.5 Kg 5 Kg Dimension LXWXH 56X3X cm 57X5X cm Wiring Diagram Switch Housing 0V 60Hz Single Phase Power Supply Black White Green Switch Circuit Breaker Red Motor Red White White Startup Capacitor 60-530μF/300V STO /3C Power Supply Cord Handle Cord Motor Cord Running Capacitor 60μF/50V ICE ip7 ip0 6
ICE Company Limited