COD: 2BP8CS00 KEPLERO RGBW,167$//$7,21 *8,'( Product Code for Zoom: KPLZML1RGBW Product Code for Wall Wash: KPLWWL2RGBW :$51,1* To ensure a maximum efficient use of the product, read the instructions before proceeding installment. *Please make sure the fixture is sealed correctly and the trim ring is properly tightened (see trim installation page 7 for details)*. This fixture must be installed by a licensed and qualified electrician. The installer must comply with NEC and local building codes when installing the fixture Electrical current can cause painful shock, serious injury, or even death. Make sure you turn off the power supply, ground fixture(s), and make sure all electrical connections are correct and secured This fixture must not be installed during rain, fog, or high humidity 45' Please allow the fixtures to run for 45 min before installing trim ring (see trim installation section for more details). For use in IP67 installations. Keep the label of the original packaging if any eventual future claims are needed Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 1 of 8
Table of Contents Packaging Contents Installation Instructions Range of Motion Accessories Installation Trim Installation Maintenance Support Page Pg.2 Pg.3-4 Pg.5 Pg.6 Pg.7 Pg.7 Pg.8 Packaging contents 4 pin: Power cable 5 pin: 1-10V dimming Keplero fixture with trim ring installed 1DU2394Installation Sleeve 1DU4343- Raised Metal Installation Pipe (Neutral) (Line) D(+) 5 D(-) 1DU2530 JUNCTION BOX 1DU2531 - DMX Connection Box 6 FOOT IP 68 CONNECTOR POWER CORD ATTENTION! CUT THE OPPOSITE SIDE WHIT THE HOLES Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 2 of 8
Installation Instructions Installers will dig out trenches to prep the PVC tube o Put gravel in the trenches for the J-Box o Requirement by UL for adequate drainage o Safety net covers below the J-Box and the conduit pipe to warn diggers what is below Position of the J-Box must be an accessible depth of 12" max required for maintenance Insert the PVC pipe with the installation sleeve o The gap between the end of the PVC pipe and the middle of the J-Box should have enough room to fix the power cord to be installed with enough slack to remove the fixture while connected o Tube is field cut adjustable for accessibility If installation requires semi-flushed installation o Break off outer ring of installation sleeve for 0.15" raise o Fixture will rest above the sleeve for a covered look For low voltage dimming feature o Provide a separate PVC conduit through the gravel to provide a run for all fixtures with dimming for parallel circuiting installation For Raised Installation o Installers will dig out trenches to prep the PVC tube o Minimum 12.75" from bottom of raised installation sleeve to ground level Installers will dig out trenches to prep the PVC Insert the PVC pipe with the installation sleeve o PVC pipe for raised installation is 36" total This allows the extension PVC tube to be field cut to create an elevated installation with a range of 1" to 23" Raised Installation Sleeve 1DU4343 In Grade Installation Sleeve (With Extension Sleeve 1DU2394) 11" 11" Installation Sleeve Grey Fitted PVC 9" *Power Cord to be installed with enough slack to remove fixture while connected 3" ' r 36" Black Stainless steel extension tube can be field cut to create an elevated installation from 1" to 23" above ground 8.50" 12" Max Distance from Top of Raised Tube to J-Box Required for Maintenance 0v-10v Control Cable Metal Extension Sleeve In Grade Junction Box with 6 Foot Power Cord COD: 1DU2530. Raised Installation Metal tube Minimum 13" to bottom of Keplero Raised Installation Tube to ensure stable installation Gravel required to supply adequate drainage 10.625" Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 3 of 8
Installation Instructions cont. DMX connection layout The KEPLERO RGBW fixtures interact with each other by DMX communication. The DMX cable attached to the fixtures comes with a 5-pin male connector which connects to a DMX connection box. The DMX buffer allows a daisy chain communication line for up to 30 fixtures max. o The end fixture will have a termination DMX connection box that will communicate to the controller the end of that run of KEPLERO fixtures. o It is the installer's responsibility that the end fixture of that run has a termination box. Failure to install the correct box will affect the communication of that line and will not communicate properly. Note: Fixtures are addressed in the factory, but can be readdressed in the field if required DMX Input 6" 5 conductor cable from Fixture with 5 pole IP68 male connector DMX Connection Box (DMX through)* 1 each 5 Pin female Connector to Fixture 1pc 3 pin Male connection for DMX input 1pc 3 pin Female connection for DMX output *MAX LENGTH OF 30 FIXTURES PER LINE* Power Input DMX Data Input DMX Jumper Factory manufactured to Required length with 1 each 3 pin female connector for DMX input 1 each 3 pin male connection for DMX output Power Output to next Keplero Unit DMX Connection Box (DMX Terminator) 1 each 5 pin female connector to fixture 1 each 3 socket male connection for DMX input DMX Jumper Factory manufactured to Required length with Belden 5501G1 3 conductor cable "Water Dog" UL Listed direct Burial Communication Cable *Jumper Cables and DMX connection Boxes to be Supplied by Contractor based on specified project layout DMX data Output to next Keplero Unit Inserting fixture into sleeve Fixture will slide into grooves of the installation with ease To provide a safe and efficient installation of fixture to the sleeve, use metal handle (optional/not included accessory) to safely insert the fixture into the installation sleeve Secure the fixture to sleeve with the three screws provided with installation sleeve x3 15 Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 4 of 8
Range of Motion Fixture's optics has two range of motion o Horizontal Axis: All Keplero fixtures' optics rotate on the horizontal plane with a range from 0-359 o Vertical Axis: For Keplero Zoom optics, optics slides on vertical axis from 0 to 0.79in to project a tilt from 0 to +200. (Keplero Wall Wash has only a horizontal range of motion). ZOOM OPTIC A 2 1 B 1 3 2 + 20 0 359 0.79in Max WALL WASHER OPTIC 359 Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 5 of 8
Accessories Installation Types of accessories o Chromatic Filters o Corrective Filters o Refractive Filters o Anti-glare Filters Guide for installing accessories o For Zoom optic: Pull the optics up to its highest position before securing it in place. Unscrew the lens cap from optics holder and insert up to two filters max in the lens cap before screwing the lens cap back on the optics holder with the added filters ZOOM OPTIC A B 1 2 3 SP FL MWFL WFL 1 2 3 O K 4 Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 6 of 8
Trim Installation Fixture comes installed with trim ring. If trim ring is opened for optics adjustment: Use a tamper-proof torx key (sold separately/optional but recommended) to remove the trim ring, the glass ring, and access the optics holder for beam spread angling Once you set position of the optics to the desired lighting angle, power on fixture and cover with black installation sleeve lid and let the fixture operate for 45 minutes before attaching glass and trim ring When securing the tamper-proof torx screws o o Apply only 2.95ft-lbs (4Nm) of torque to efficiently secure the fixture Torque screws in star formation to provide a tight, even, and secure holding for the trim ring 4 Nm 4 2 6 5 45' 1 3 Maintenance This fixture was designed and manufactured for a durable, long lasting use with minimum care. To ensure the maximum lifespan of this product, we encourage our customer to provide a quality visual inspection of dirt, abnormalities, or signs of moisture inside or around the fixture every six months. If there are any visible sign of issues during the inspection, please open the fixture, wipe off any moisture inside the fixture and clean any of the dirt off the fixture with a soft cloth with cleaning solution around the trim ring and the ring of the fixture. o o Once finished with fixture maintenance, be sure to install back the trim ring according to trim installation directions above. Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 7 of 8
Support Any questions, problems, or comments you have please feel free to contact our Customer Service department during our business hours Monday-Friday 8am-5pm via: Email: usaorders@targett.com Phone: (714) 513-1991 Visit our website: http://www.targetti.us Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 8 of 8
Support Any questions, problems, or comments you have please feel free to contact our Customer Service department during our business hours Monday-Friday 8am-5pm via: Email: usaorders@targett.com Phone: (714) 513-1991 Visit our website: http://www.targetti.us Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 03.2017 - Page 8 of 8
Maintenance This fixture was designed and manufactured for a durable, long lasting use with minimum care. To ensure the maximum lifespan of this product, we encourage our customer to provide a quality visual inspection of dirt, abnormalities, or signs of moisture inside or around the fixture every six months. If there are any visible sign of issues during the inspection, please wipe off any dirt and/or moisture inside the fixture and/or clean off the dirt with a soft cloth with the correct cleaning solution around the fixture. Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 07/2017 - Page 5 of 7
Support Any questions, problems, or comments you have please feel free to contact our Customer Service department during our business hours Monday-Friday 8am-5pm via: Email: usaorders@targett.com Phone: (714) 513-1991 Visit our website: http://www.targetti.us Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 07/2017 - Page 6 of 7
Targetti USA - A Targetti Group Company - 750-A W. 17th. St. Costa Mesa, CA 92627 - (714) 513-1991 Email: targettiusa@targetti.com - www.targetti.us - 07/2017 - Page 7 of 7