OF FIRE CS24C Colored Light Strobe/orn Series igh Candela Ceiling/Wall Mount Patent Pending Description AMSECO's UL listed Colored Light Strobe CS24C series is designed to provide audible and visual signals for Fire Alarm Protection Systems and notification signals for the purpose of life safety and property protection. They meet or exceed NFPA/ANSI standards and UL 464/UL638. The CS24C is a Select-A-orn with the highest strobe light output (non-selectable candela). The colored light is available in,, and. The light output candela ratings vary depending on the lens color. In those instances where two or more AMSECO horns and/or strobes are connected and requires a synchronized code 3 temporal pattern and/or a synchronized strobe flash, all models can be synchronized when used in conjunction with AMSECO UL listed Sync module SMD-3A to meet the latest code. Features Available colored lights: amber, blue, green, red NFPA/ANSI compliant UL listed for Ceiling/Wall Mounting under UL 638 Designed for use in non-sleeping areas Screw terminal capacity up to 2 AWG Polarized strobes with wide operating voltage range using filtered DC or unfiltered FWR input voltage orn field selectable tones: 3z interrupted or mechanical Temporal or Non-temporal igh or Low dba output Minimum one flash per second (z) All models mount to 4" X 4" X -fi" back box Synchronization requires an AMSECO SMD-3A Sync Module RBX- back box skirt for surface mount (optional) The SPC- retrofit plate allows mounting to a variety of back boxes Available in red or white housing C US L I S T I NG S E R V CALIFORNIA MARSALL I C E Ordering Information Model Number Colored Light ousing Color Input Voltage Strobe Candela Mounting Type Light Output Flash Rate (Times/min) Sync Module Temperature Range CS24C-AW CS24C-BW CS24C-GW CS24C-RW CS24C-WW CS24C-AR CS24C-BR CS24C-GR CS24C-RR CS24C-WR 24V DC/FWR 38 38 38 38 Wall or Ceiling Mount Non- Selectable 6 SMD-3A 32 F ~ 2 F ( C ~ C)
Engineering Specifications The audible and colored visual alarm indicating appliance shall be AMSECO model CS24C or equivalent device. The orn/strobe shall be listed under UL 97 and UL 638 Standard for signaling devices and shall be approved for fire protective and emergency services. The reflective mirror shall be of the same color as the lens of amber, blue, green, or red. The candela output shall have a single setting of igh intensity output. The orn shall provide two different field selectable tones and a igh and Low field sound output setting. The signaling orn/strobe shall operate on 24VDC from a non-coded regulated DC supply or full-wave rectified, unfiltered supply. The signaling strobe shall be designed to produce a signal flash of one flash per second with continuously applied minimum voltage. The orn/strobe shall be capable of CEILG and WALL mounting to a variety of back boxes using the AMSECO SPC- retrofit back plate. When strobe synchronization is required, the orn/strobe shall be compatible with the AMSECO SMD-3A (daisy chain) or other source of AMSECO sync protocol. Strobe Selectable Candela Output Select-A-Switch Select either Low, Mid or igh and replace cap on front of unit. Dimensions: Inches (mm) 4" Square outlet box /2" Deep 3-3/8 (85.7) 6-7/8 () -3/32 (35) 2-25/32 (7) 3-3/8 (85.7) Top View Side View Back View Wiring Diagrams Example : Colored light WIRG WIRG 2 Signal Operates Independently Refer to Fig. Control Panel To Next Device or End-of-Line Resistor STROBE ORN To Next Device or End-of-Line Resistor WIRG 3 Wiring Diagram for Audble Strobe Class "B" with Audible Silence Feature. (CS24W) Refer to Fig. 2 Strobe Signal orn Signal SYNC MODULE SMD-3A PUT PUT Fig. orn/strobe WIRG 4 Wiring Diagram for Audble Strobe Class "B" without Audible Silence Feature. Signal SYNC MODULE SMD-3A PUT PUT Refer to Fig. 2 Fig.2 STROBE ORN orn/strobe Factory setting jumper wire STROBE ORN WARNG The Strobe/orn must be used only on circuits with continuously operating voltage. DO NOT use strobe on coded or interrupted circuits in which the applied voltage is interrupted ON and OFF as the strobe may fail to flash. The applied voltage must be within its rated input voltage range. Fuse ratingson signaling circuits must handle peak currents from all devices connected to those circuits.
orn Selectable Jumper Setting Fig. A TONE SELECT JUMPER Factory setting PC3PC2PC Fig. B PC3 JUMPER PATTERN PC2 PC TONE VOLUME NON ELECTRO TEMPORAL MECANICAL TEMPORAL 3z Specifications Strobe/orn Current Draw Table orn & Strobe orn ONLY Non-Temp. Temporal Non-Temp. Temporal 3 z 3 z 3 z 3 z PC3: Pattern PC2: Tone PC: Volume PC3 PC2 PC Max. RMS Current (marms) 42 42 42 42 24V FWR 5 5 5 5 Min. Sound Output (dba @ ft per UL464) 86 76 87 77 8 73 82 86 76 87 77 8 73 82 Strobe Light ONLY Max. RMS Current (marms) Light Output Dispersion 24V FWR 359 2 Sound Output Dispersion DEGREES +9 +6 +3-3 -6 orizontal db db db -3dB Light Output on Axis (cd) 38 38 Vertical -5dB -db db -db -9-6dB -5dB Installation and Mounting Options SPC- Universal Retrofit Plate: designed for mounting to a variety of back boxes. RBX- Skirt: for surface mount installations. Single Gang Double Gang Octagon 4 Square SPC- SPC- SPC- 4 Square RBX- Back Box Skirt RBX- RBX- RBX- CS24C
OF FIRE SMD-3A Sync Module L I S T I NG CALIFORNIA S E R V MARSALL I C E Description The Sync Module is designed to provide a synchronized temporal pattern (code 3) tone, and synchronize the strobe flashes when used with AMSECOs Select-A- Strobe, Select-A-orn, and Select-A-orn/Strobe series as well as the ability to silence the horn while maintaining the strobe flashes. The SMD-3A has the capability of connecting two style Y (Class B) circuits or one style Z (Class A) circuit and is rated for 3 Amperes per circuit. Features Polarized with wide operating voltage range using filtered DC or unfiltered FWR input voltage Mounts onto 4-inch square back box Daisy chain up to 2 modules maximum Screw terminal capacity up to AWG#2 metal plate The SMD-3A can be interconnected so that more than 2 alarm zones can be synchronized by connecting the SYNC terminals (daisy chain connection). The maximum number of interconnected modules is twenty. All inputs are polarized for compatibility with standard reverse polarity supervision of circuit wiring by Compatible AMSECO products S24W-5375 SL24W-5375 SB24-75 SAD24-5375 RSD24-5375 SCM24W-375 S24W-75 SL24W-75 SLB24-75 SAD24-75 RSD24-75 SCM24W-77 24W SA24 Series SB24 Series Colored Light Strobe Series Specification Input Voltage Voltage Range Maximum Load on Loop Max. RMS Current DC FWR Mounting Temperature Range 24V DC/FWR 6 ~ 33V DC/FWR 3A Average Max. 5A Peak ma 68mA 4 x 4 x -/2 32 F ~ 2 F ( C ~ C) Dimensions: inches(mm) 4.33 () 3.3 (85.7) 4.33 () 3.3 (85.7).2 (5) Daisy Chain Modules No. No.2 No.2 (max.) SMD-3A +PUT +PUT - GND +PUT2 +PUT2 + - SMD-3A +PUT +PUT - GND +PUT2 +PUT2 + - SMD-3A +PUT +PUT - GND +PUT2 + - +PUT2 *Due to continuous development of our product line, specifications are subject to change without notice. CS24C /24