Installation Instructions odel CABBATT/R Box INTRDUCTIN The odel CABBATT/R Box from, is used to house BTX2 (55AH) batteries for XL Systems; BTX2 (55AH) batteries and BTX3 (00AH) batteries for FireFinderXLS/Desigo Fire Safety odular/cerberus PR odular Systems; and 00AH battery sets for the FS250 and FS250C Systems. The CAB BATT is black and the CABBATTR is red. The CABBATTR will be referred to in the remainder of this document as the CABBATT. The CABBATT consists of a door and a backbox, as shown in Figure. The door is permanently hinged left. The battery box can be placed on the floor directly underneath the fire panel enclosure to which it supplies battery backup or it can be mounted on a flat surface with four usersupplied bolts that are a maximum of 3 /8 inch in diameter. When used for Seismic applications, the battery box must be placed on the floor and mounted to the wall as described on page 2. KNCKUTS FR WIRING Figure CABBATT Enclosure CABBATT CABBBATT battery box is for indoor use only in dry environments. INSTALLATIN Prior to installation consider the following: Weight and size of the enclosure. Local codes. P/N 35033970 Building Tec echnologies Division
Install the battery box:. Select a clean, dry, shock and vibration free surface in a protected environment. 2. Position the battery box directly beneath the fire panel enclosure to which it will be wired. (Knockouts in the battery box may be needed to line up with the knockouts in the fire panel enclosure.) 3. Position the battery box so that it is clear of obstructions and the front door opens freely. 4. ark the locations of the two upper mounting bolts of the battery box (marked A ) on the wall. (Refer to Figure 2.) 2.25 in.06 in 6.63 in 8.0 in A C SIEENS INDUSTRY, INC. FLRHA PARK, NJ, 07932 DEL CABBATT INSTALLATIN INSTRUCTINS P/N 3503397 C A 3.2 in 9.00 in B ø0.437 in (3 HLES) B D Figure 2 ounting Holes for CABBATT 26.25 in 5. Drill the two holes located in the previous step and screw in the top bolts, leaving a small gap between the wall and each top bolt. 6. Place the battery box over the two top bolts and allow it to slide down over the bolts. 7. ark, drill, and install the two bottom bolts in the battery box (marked B ). 8. Tighten all four bolts securely against the back wall of the battery box. 9. Place the batteries in the bottom of the CABBATT. Seismic Applications For Seismic applications the CABBATT must be placed on the floor and mounted to the wall using bolts that are 3 /8 inch in diameter.. Select a clean, dry, shock and vibration free surface in a protected environment. 2. Position the battery box directly beneath the fire panel enclosure to which it will be wired. (Knockouts in the battery box may be needed to line up with the knockouts in the fire panel enclosure.) 3. Position the battery box so that it is clear of obstructions and the front door opens freely. 4. ark the locations of the two upper mounting bolts of the battery box (marked A ) on the wall. (Refer to Figure 2.) 5. Drill the two holes located in the previous step and screw in the top bolts, leaving a small gap between the wall and each top bolt. 6. Place the battery box over the two top bolts and allow it to slide down over the bolts. 7. ark, drill, and install the remaining two top bolts (marked C ). 8. For installations using 55 AH batteries, mark, drill, and install the two bottom bolts in the battery box marked B, as shown in Figure 2. 2 P/N 35033970
For installations using 00 AH batteries, mark, drill, and install the bottom bolt in the backbox marked D, as shown in Figure 2. 9. Tighten all bolts securely against the back wall of the battery box. 0. Place the batteries in the bottom of the CABBATT.. To complete the installation for Seismic applications, refer to the CAB55 BRKT and CAB00 BRKT Installation Instructions, P/N 35050547. WIRING The main AC power line must be turned FF prior to installation. Install Wiring Wire in accordance with local codes and NEC 760. Connections. Remove the knockouts in the top of the battery box and bottom of the fire panel enclosure for entry of battery wiring. 2. Connect the Wire Assembly to the batteries in the CABBATT. If a longer wire is required, use a minimum of 2 AWG. For FireFinderXLS/Desigo Fire Safety odular/cerberus PR odular, use P/N 465633943, supplied with the PSC2 (Refer to Figure 4 and the PSC2 Installation Instructions, P/ N 35033060.) For FS250 or FS250C use the Cable Assembly supplied with the FS250 / FS250C hardware kit (Refer to Figure 5). For XL, use P/N 55549033 supplied with the B3 (Refer to Figure 6). When BTX, BTX2 or BTX3 batteries are required, connect them to the system with the Cable Conversion Kit, P/N 545634222, following the steps listed below.. Using the 2 in. long wire assembly, connect the two batteries together, as shown in Figure 3. Secure each end of the assembly to the battery with a 032 x 3/4 screw and lock nut. 2. Attach the quick disconnects to the positive and negative battery terminals with the 032 x 3/4 screws and lock nuts supplied. 3. Attach the red battery wire to the quick disconnect on the positive terminal and the black battery wire to the quick disconnect on the negative terminal. QUICK DISCNNECT (2 PLACES) 032 X 3/4 SCREWS (4 PLACES) 2 IN. LNG WIRE ASSEBLY LCK NUT (4 PLACES) BTX, BTX2 R BTX3 BATTERIES Figure 3 Wiring BTX/2/3 Batteries using Cable Conversion Kit, P/N 545634222 SPECIFICATINS CABBATT: 26 / 8 W x 8 3 / 8 D x 3 3 / 25 H 3 P/N 35033970
HNET/CAN RESET PWER DULE FAIL CAN FAIL H NET FAIL GND FAULT 24V 2 FAIL 24V 4A FAIL H H N GND BATTERY FF 2 3 N GND H N N GND 2 3 H N GND GND N H J 2 2 3 3 4 4 CC5 CC5 TYPICAL CAB2 ENCLSURE CC5 P5 TB P4 TB3 P0 PSC2 TAPER SWITCH FSNPE TRANSFRER (PTINAL) FSB / FSB2 TX3 T DISPLAY BARD BRDG FSDLC ( FS250) R FDLC (FS250C) TX2 _ P9 TB2 TB4 2 _ P2 FSNPE TX FSDACT R FST P4 P5 P3 AC PWER BAT. TB2 P PTB TB P2 BATTERY WIRE ASSEBLY PRVIDED WITH HARDWARE KIT CABBATT 2 in. long wire provided with PSC2 Black Wire Wire Assembly P/N 465633943 Red Wire CABBATT Black Wire 2 LNG WIRE PRVIDED WITH HARDWARE KIT Red Wire Figure 4 Typical Connections from FireFinderXLS/ Desigo Fire Safety odular/cerberus PR odular to CABBATT Figure 5 Typical Connections from FS250 / FS250C to CABBATT P2 P3 TB5 PI TB TB3 B TB2 TB5 TYPICAL XL ENCLSURE TB TB4 TB4 TB2 4 4 4 P5 o r P8 P5 o r P8 P5 o r P8 PS6 R PS2 Wire Assembly CABBATT Figure 6 Typical Connections from XL to CABBATT 4 P/N 35033970
Cyber security disclaimer Siemens products and solutions provide security functions to ensure the secure operation of building comfort, fire safety, security management and physical security systems. The security functions on these products and solutions are important components of a comprehensive security concept. It is, however, necessary to implement and maintain a comprehensive, stateoftheart security concept that is customized to individual security needs. Such a security concept may result in additional sitespecific preventive action to ensure that the building comfort, fire safety, security management or physical security system for your site are operated in a secure manner. These measures may include, but are not limited to, separating networks, physically protecting system components, user awareness programs, defense in depth, etc. For additional information on building technology security and our offerings, contact your Siemens sales or project department. We strongly recommend customers to follow our security advisories, which provide information on the latest security threats, patches and other mitigation measures. http://www.siemens.com/cert/en/certsecurityadvisories.htm 5 P/N 35033970
THIS PAGE HAS BEEN LEFT INTENTINALLY BLANK. 6 P/N 35033970
THIS PAGE HAS BEEN LEFT INTENTINALLY BLANK. 7 P/N 35033970
Florham Park, NJ Siemens Canada, Ltd. 577 North Service Road East akville, ntario L6H 0H6 Canada Document ID A6V035587 P/N 35033970