Classic Series SD Geothermal Heating and Cooling System

Classic Series SD Geothermal Heating and Cooling System Quick-Start Instructions SD-QS (12/16) 2016 EarthLinked Technologies, Inc.

Table of Contents List of Revisions... 4 Model Nomenclature... 5 Safety... 6 Equipment Manuals... 6 Installation... 7 1) Component Matching... 7 2) Compressor Unit Placement... 8 3) Refrigeration... 9 4) System Applications and Electrical... 13 5) SureStart... 22 6) Internal Heat Recovery System... 26 Earth Loop Protection System... 29 1) Anode Wire Installation... 29 2) EPS Operation and Service... 34 3) Voltage Verification... 35 Start-Up Process... 36 1) System Leak Check... 36 2) Evacuation... 39 3) Initial Charge... 41 4) Final Charge... 43 Troubleshooting... 48 1) Compressor... 48 2) System... 52 Commissioning Document... 55 Tools and Equipment... 56 Triple Evacuation... 57 Appendix: Electrical Diagrams No SureStart... 58 SD-QS (12/16) Page 2

List of Figures Figure 1. Matching Component Model Numbers... 7 Figure 2. General Layout of System Components... 8 Figure 3. Compressor Unit Bracket Installation... 9 Figure 4. Compressor Unit Clearance... 9 Figure 5. SD Connections... 10 Figure 6. Line Set Sizes... 12 Figure 7. SD Electric Box Components & Electrical Data... 14 Figure 8a. SD Compressor Unit Electrical Ladder Diagram, 230-1-60... 15 Figure 8b. SD Compressor Unit Electrical Schematic Diagram, 230-1-60... 16 Figure 9a. SD Compressor Unit Electrical Ladder Diagram, 230-3-60... 17 Figure 9b. SD Compressor Unit Electrical Schematic Diagram, 230-3-60... 18 Figure 10a. SD Air Heating/Cooling/Water Heating Application... 19 Figure 10b. SD Air Heating/CoolingWater Heating: AVS Field Wiring Diagram... 20 Figure 10c. SD Air Heating/CoolingWater Heating: AVV Field Wiring Diagram... 21 Figure 11. SureStart Mode of Operation... 23 Figure 12. Standard Storage Water Heater Service Connections... 26 Figure 13a. GSTE Storage Water Heater - Service Connections... 27 Figure 13b. GSTE Storage Water Heater Tank Top View... 27 Figure 14. Compressor Cabinet Socket/Cap... 29 Figure 15. Disassembled Plug Connector... 30 Figure 16. Anode Wire Insertion... 31 Figure 17. Install the Plug Insert... 32 Figure 18. Engage the Gland Nut... 32 Figure 19. Secure the Anode Wire.... 33 Figure 20. The Plug and Socket Joint... 33 Figure 21. Electric Box with EPS Components... 34 Figure 22. EPS Voltage Ratings... 35 Figure 23. Typical Test for DC Voltage... 35 Figure 24. SD Internal Flow Schematic... 37 Figure 25. SD Piping... 38 Figure 26. Evacuation of SD System... 40 Figure 27. Initial Charge of SD System... 42 Figure 28. Final Charge of SD System... 44 Figure 29. Charging to the Middle Sight Glass(Heat only units)... 45 Figure 30. Final charging to the Top Sight Glass(Heat/Cool units)... 45 SD-QS (12/16) Page 3

Figure 31. Pressure-Temperature for R-410A... 46 Figure 32. Start-Up Process... 47 Figure 33. Compressor Unit Voltage Information... 49 Figure 34. Compressor Motor Circuit Testing... 50 Figure 35. Compressor Motor Grounded Winding Test... 51 Figure 36. System Troubleshooting Chart... 52 Figure A1: SD Compressor Unit Electrical Ladder Diagram (No SureStart), 230-1-60..59 Figure A2: SD Compressor Unit Electrical Schematic Diagram (No SureStart), 230-1-60 60 Figure A3: SD Compressor Unit Electrical Ladder Diagram (No SureStart), 230-3-60..61 Figure A4: SD Compressor Unit Electrical Schematic Diagram (No SureStart), 230-3-60....62 List of Revisions New EPS system Revised Electric Box Carried over: SureStart does not come standard on Classic Series compressor units anymore. It remains an option, similarly to the EDM system and the Silencing kit Revised charging method due to elimination of TXV Removed the requirement to add 1,000 BTUH to the Heating Load for each occupant if domestic water heating by Heat Recovery Module (HRM) is part of the system. See Technical Bulletin TEC-021616 Removed sections regarding hydronic (see SDH, SCW or SCWD for this application) SD-QS (12/16) Page 4

Model Nomenclature Disclaimer Proper installation and servicing of the EarthLinked Heat Pump is essential to its reliable performance. All EarthLinked systems must be installed and serviced by an ETI trained and authorized technician. Installation and service must be made in accordance with the instructions set forth in this manual. Failure to provide installation and service by an ETI trained and authorized installer in a manner consistent with this manual will void and nullify the limited warranty coverage for the system. Earthlinked Technologies shall not be liable for any defect, unsatisfactory performance, damage or loss, whether direct or consequential, relative to the design, manufacture, construction, application or installation of the field specified components. Earthlinked Technologies, Inc. 4151 S. Pipkin Road Lakeland, Florida 33811 USA phone: 863-701-0096 toll-free: 866-211-6102 General Info: info-question@earthlinked.com www.earthlinked.com CSI # 23 80 00 SD-QS (12/16) Page 5

Safety Warning, Caution and Important notices appear throughout the manual. Read these items carefully before attempting installation, servicing or troubleshooting the equipment. IMPORTANT! Notification of installation, operation or maintenance information which is important, but which is not hazardous. WARNING! Indicates a hazardous situation, which if not avoided will result in serious injury or death, or equipment or property damage. CAUTION! Indicates a potentially hazardous situation or an unsafe practice, which if not avoided, may result in injury, or equipment or property damage. Equipment Manuals The following is a listing of the equipment installation manuals that are provided with each component specified for this EarthLinked system. IMPORTANT! Read and follow all installation instructions in these manuals, appropriate for the EarthLinked system being installed, BEFORE initiating the Start-Up procedure. Series SV Service Valve and AKS Adapter Kit Series AVS and AVV Air Handler Series CCS Cased Coil Series HCM Hybrid Cooling Module Series GSTE Storage Water Heater Series GST Storage Water Tank Model HHK/CWK-1872 Temperature Control Kit Earth Loop Specification and Installation Manual Earth Loop Protection Kit Installation Manual SD-QS (12/16) Page 6

Installation 1) Component Matching Upon receipt of the equipment, carefully check the component model numbers by referencing Figure 1, to ensure that all components of the system match. Classic Compressor Model 1 ETI Four Speed Air Handler Model 3 Arcoaire Four Speed Air Handler Model 3 ETI Variable Speed Air Handler Model 3 Arcoaire Variable Speed Air Handler Model 3 ETI Cased Coil Model 3 Arcoaire Cased Coil Model 3-024 AVS-0024-C* FEM4P3000AL AVV-0024-C* FVM4X3600BL CCS-0024-C* EAM4X30L17A Hybrid Cooling Module 3 Earth Loop 2-036 AVS-0036-C* FEM4P4200AL AVV-0036-C* FVM4X4800BL CCS-0036-C* EAM4X42L24A -036-C HCM-1860C -042 AVS-0042-C* FEM4P4800AL AVV-0042-C* FVM4X4800BL CCS-0042-C* EAM4X48L24A -042-C -024-C -030 AVS-0030-C* FEM4P3600AL AVV-0030-C* FVM4X3600BL CCS-0030-C* EAM4X36L21A -030-C -048 AVS-0048-C* FEM4X6000BL AVV-0048-C* FVM4X6000BL CCS-0048-C* EAM4X60L24A -048-C -060 AVS-0060-C* FEM4X6000BL AVV-0060-C* FVM4X6000BL CCS-0060-C* EAM4X60L24A -060-C 1. Contained in each compressor package: compressor unit; four L-shaped hold down brackets; service valves-liquid and vapor; adapters for service valves and earth loop line set; product literature 2. All series Earth Loops 3. Air handlers and cased coils are ordered as either CV = Vertical or CH = Horizontal. Figure 1. Matching Component Model Numbers Warning! WEAR ADEQUATE PROTECTIVE CLOTHING AND PRACTICE ALL APPLICABLE SAFETEY PRECAUTIONS WHILE INSTALLING THIS EQUIPMENT. FAILURE TO DO SO MAY RESULT IN EQUIPMENT AND/OR PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. Guidelines for the general layout of the system components are shown in Figure 2. Before placing the compressor unit (outside or indoors), review the guidelines in Figure 2. INSTALLATION GUIDELINES All refrigerant and water lines between these above ground components must be insulated with at least 1/2 wall thickness Armaflex, Insul-Tube or equivalent insulation. Thicker insulation is recommended for the Compressor Unit-to-Air Handler refrigeration lines for sound isolation If you plan to exceed the 40 ft. max elevation of the Air Handler, please contact our Tech Support Department. Increased height will reduce performance and shall be factored into system sizing. The Hydronic Water Module (HWM) shall always be mounted above the Compressor Unit, never below SD-QS (12/16) Page 7

Figure 2. General Layout of System Components 2) Compressor Unit Placement EarthLinked compressor units may be located inside or outside. If outside, place compressor unit on a standard HVAC outdoor unit pad. If inside, place it on a level, hard surface. If the compressor unit is to be fastened down, see Figure 3 for bracket installation. Avoid placing the compressor unit in or near the living area of the residence. Attic installations must include a condensate pan with drain, and suspension from rafters with suspension isolators. Clearance around the unit for service is illustrated in Figure 4. However, local codes and applicable regulations take precedence. SD Compressor Unit must be placed in an environment in which the surrounding air temperature does not drop below 40 F. If the compressor unit or other refrigerant-containing system components are located indoors, they shall be in a location which (1) is an unoccupied space, or (2) is served by the circulating air system, or (3) provides 280 cu. ft. of open space per nominal ton of rated system capacity. The 2012 International Mechanical Code defines residential occupancy as including permanent provisions for living, sleeping, eating cooking, and sanitation. Consult local code authorities to define unoccupied space for the specific installation. SD-QS (12/16) Page 8

Figure 3. Compressor Unit Bracket Installation Figure 4. Compressor Unit Clearance Placement instructions for other pieces of equipment that make up the EarthLinked System are included with those pieces of equipment and are listed in this manual under Equipment Manuals. 3) Refrigeration After the EarthLinked compressor unit and other system components are placed, the refrigeration system tubing is run from the compressor unit to the other components, as appropriate. Figure 5 illustrates the refrigeration and electrical connection points for the SD compressor unit. IMPORTANT! EarthLinked compressor units that provide space cooling shall be equipped with an EarthLinked Hybrid Cooling Module (HCM) when: (1) Required by the performance tables; OR (2) System is in a Cooling dominant application where soil thermal conductivity is unknown or known to be poor (less than 1 BTU/hr.ft. F). Examples of such soils are light dry soil, dry sand, peat and organic soils, dry clay and hardpan; OR (3) In any system where soil thermal conductivity is unknown or known to be poor (see (2) for definition) and ambient outdoor temperatures have exceeded the outdoor summer design temperature conditions for a continuous system run time of at least 7 hours. SD-QS (12/16) Page 9

IMPORTANT! EarthLinked compressor units that provide space heating shall be equipped with a Heating Performance Enhancement kit (HPE) when required by the performance tables. PORT FUNCTION TYPE OF CONNECTION SIZE, INCHES -024-030 -036-042 -048-060 A 1 Electrical, Power 1-1/4 Hole --- --- --- --- --- --- B 1,2 Electrical, Control 7/8 Hole --- --- --- --- --- --- 1 AH/CC Liquid Braze 1/2 1/2 1/2 1/2 1/2 1/2 2 Plugged --- --- --- --- --- --- --- 3 EL Liquid* Braze 3/8 3/8 1/2 1/2 1/2 1/2 4 Anode Socket -- --- --- --- --- --- --- 5 EL Vapor* Braze 5/8 3/4 3/4 3/4 7/8 7/8 6 AH/CC Vapor Braze 3/4 3/4 3/4 7/8 7/8 7/8 7 DWT Supply Braze 1/2 1/2 1/2 1/2 1/2 1/2 8 DWT Return Braze 1/2 1/2 1/2 1/2 1/2 1/2 9 Plugged ---- ---- ---- ---- ---- ---- ---- 10 Plugged ---- ---- ---- ---- ---- ---- ---- N = Nameplate and other information 1: Nominal electrical connector sizes 2: Two additional electrical control ports on opposite side. Same size *Line set sizes with provided compressor unit adapters LEGEND AH Air Handler CC Cased Coil EL Earth Loop DWT Domestic Water Tank Figure 5. SD Connections SD-QS (12/16) Page 10

Compressor units are shipped from the factory with a low pressure nitrogen holding charge. Carefully relieve the holding charge when the compressor unit is being prepared to connect refrigerant system piping. Caution! This compressor unit is equipped with Copeland Ultra 32-3MAF Polyol Ester Oil (POE). This is the only brand and type of oil that is recommended for use with ETI compressor units. POE oil absorbs significant amounts of moisture from the air very rapidly. Exposure of the POE oil to air must be minimized. Even a few minutes of exposure to air can be harmful to the system. After the initial nitrogen holding charge has been released from the compressor unit, it is critical that air not be allowed to enter the compressor unit during the process of preparing compressor unit refrigerant connections (tube cutting, deburring, cleaning, brazing, etc). To ensure air does not enter the compressor unit while preparing refrigerant connections, trickle dry nitrogen through the compressor unit, entering at the access port nearest the Active Charge Control (ACC), to keep airborne moisture out of the compressor unit and the POE oil. Complete preparing and brazing all compressor unit refrigerant connections at one setting to minimize exposure of open connections to air. Failure to implement the above precautions will result in an extended period of time to effectively evacuate the system, and may adversely affect system performance and cause system failure. Caution! REFRIGERANT PIPING CONNECTIONS Refrigerant joints are to be brazed with 15% silver content brazing alloy, utilizing the NITROGEN BRAZING PROCESS. NITROGEN BRAZING PROCESS PURPOSE: Utilize the NITROGEN BRAZING PROCESS on all brazed refrigerant piping connections. This process eliminates oxidation products from inside joint surfaces. TECHNIQUE: Trickle nitrogen gas at 1-2 psi pressure through the joint area being brazed, to displace the oxygen. When oxygen has been displaced, turn off the nitrogen, and relieve the pressure at the joint to atmospheric prior to brazing. CONSEQUENCES: Failure to displace oxygen with nitrogen at the brazed joint will result in particulate matter being released into the system. The result is discoloration of refrigerant oil, contamination of the system and possible system failure. SD-QS (12/16) Page 11

The compressor unit package contains a service valve kit and an adapter kit. The two service valves are to be installed on the earth loop vapor and liquid connections of the compressor unit, using the adapters to right-size to the proper earth loop line set. Installation of the service valves will provide isolation of the earth loop system from the compressor unit and provide easy access to the refrigerant system. For the installation of system components requiring refrigeration connections, refer to Figure 6 for line set sizes and the appropriate installation manual(s) following Figure 6. LINE SET ADAPTERS REQUIRED FOR THE AIR HANDLER OR CASED COIL ARE FIELD SUPPLIED. CHECK ALL APPROPRIATE COMPRESSOR UNIT STUB-OUT TUBING SIZES FOR REQUIRED FIELD SUPPLIED ADAPTERS! EARTHLOOP, AIR HANDLER, CASED COIL LINE SETS COMPRESSOR UNIT SIZE LINE SET O.D., INCHES LIQUID VAPOR 2.0 Tons (-024) 3/8 5/8 2.5 Tons (-030) 3/8 3/4 3.0 Tons (-036) 1/2 3/4 3.5 Tons (-042) 1/2 3/4 4.0 Tons (-048) 1/2 7/8 5.0 Tons (-060) 1/2 7/8 *Liquid and Vapor lines must BOTH be insulated with Armaflex or equivalent with at least 1/2 wall thickness for the full length of the line set. Figure 6. Line Set Sizes Series SV Service Valve and AKS Adapter Kit Series AVS and AVV Air Handler Series CCS Cased Coil Series HCM Hybrid Cooling Module Earth Loop Specification and Installation Manual After installing and nitrogen brazing the HVAC system components and compressor unit service valves, turn the Service Valves to Full Open and pressurize the refrigeration system to 150 psig with dry nitrogen and a trace of refrigerant. Valve off the nitrogen Tank from the HVAC system components and check joints with a sensitive Electronic Leak Detector and bubble solution to ensure they are sealed. Repair any leaks and re-test as appropriate. SD-QS (12/16) Page 12

4) System Applications and Electrical The SD compressor unit electrical box major components and electric data for all compressor sizes are shown in Figure 7. The SureStart Module is an optional factory installed component that (1) reduces compressor starting current; (2) reduces compressor starting torque, thus reducing stress on the compressor at start-up; and (3) monitors the run capacitor. The electrical diagrams that follow include the SureStart. For compressor unit electrical diagrams that do not include SureStart, see the Appendix. The Earth Loop Protection Control System, comprised of the EPS Power Supply, EPS Module and EPS Fuse is contained within the electric box. This system is factory wired and ready to be connected to the anode wire through an external electrical connection on the backside of the compressor cabinet. The anode wire connection is detailed in a later section of this manual. SD Heating and Cooling System electrical and application illustrations are as follows. Figure 8a. SD Compressor Unit Electrical Ladder Diagram, 230-1-60 Figure 8b. SD Compressor Unit Electrical Schematic Diagram, 230-1-60 Figure 9a. SD Compressor Unit Electrical Ladder Diagram, 230-3-60 Figure 9b. SD Compressor Unit Electrical Schematic Diagram, 230-3-60 Figure 10a. SD Air Heating/Cooling/Water Heating System Application Figure 10b. SD Air Heating/Cooling/Water Heating System Field Wiring Diagram SD-QS (12/16) Page 13

Compressor Unit Model Compressor Model Voltage/Phase/ Hz Min. Voltage LRA RLA MCA MFS -024-1C ZP25K6E-PFV 230-1-60 207 253 72.5 15.0 18.0 30-024-2C ZP25K6E-TF5 230-3-60 207 253 61.4 9.8 12.0 20-030-1C ZP31K5E-PFV 230-1-60 207 253 79.0 18.6 23.0 35-030-2C ZP31K5E-TF5 230-3-60 207 253 73.0 11.6 14.0 20-036-1C ZP38K5E-PFV 230-1-60 207 253 109.0 22.1 27.0 40-036-2C ZP38K5E-TF5 230-3-60 207 253 83.1 15.1 19.0 30-042-1C ZP44K5E-PFV 230-1-60 207 253 135.0 23.9 29.0 50-042-2C ZP44K5E-TF5 230-3-60 207 253 98.0 16.1 20.0 30-048-1C ZP51K5E-PFV 230-1-60 207 253 134.0 29.4 36.0 60-048-2C ZP51K5E-TF5 230-3-60 207 253 110.0 17.8 22.0 35-060-1C ZP61K5E-PFV 230-1-60 207 253 178.0 34.3 42.0 60-060-2C ZP61K5E-TF5 230-3-60 207 253 136.0 21.9 27.0 40 LRA = Locked Rotor Amps RLA = Rated Load Amps MCA = Minimum Circuit Ampacity Max. MFS = Maximum Fuse or HACR Circuit Breaker Size (External) Average Wire Size = Consult NEC and Local Codes Figure 7. SD Electric Box Components & Electrical Data SD-QS (12/16) Page 14

Figure 8a. SD Compressor Unit Electrical Ladder Diagram, 230-1-60 SD-QS (12/16) Page 15

Figure 8b. SD Compressor Unit Electrical Schematic Diagram, 230-1-60 SD-QS (12/16) Page 16

Figure 9a. SD Compressor Unit Electrical Ladder Diagram, 230-3-60 SD-QS (12/16) Page 17

Figure 9b. SD Compressor Unit Electrical Schematic Diagram, 230-3-60 SD-QS (12/16) Page 18

Figure 10a. SD Air Heating/Cooling/Water Heating Application SD-QS (12/16) Page 19

Figure 10b. SD Air Heating/CoolingWater Heating: AVS Field Wiring Diagram SD-QS (12/16) Page 20

Figure 10c. SD Air Heating/CoolingWater Heating: AVV Field Wiring Diagram SD-QS (12/16) Page 21

5) SureStart Features: SureStart is an optional factory installed soft starter that reduces light flicker caused at start-up by scroll compressor motors. This control has the following features: 60 to 70% reduction in direct in-rush current Under voltage protection Motor reversal protection Self-adjusts for optimal start performance 50/60 Hz compatible ETL, CE, EMC and RoHs compliant Tolerant to dirty power conditions Fault LED Internal current limiting Run capacitor monitoring SureStart is factory wired for the appropriate power supply Operation: When the system control calls for compression operation, the compressor contactor will energize. If the supply voltage is less than minimum start-up voltage, a 50 second delay is initiated. At the end of the delay, another attempt will be made to start the compressor unless the supply voltage remains unchanged. See Figure 11 for the SureStart Mode of Operation. SureStart uses an optimated starting process that learns the starting characteristics of the compressor to further refine the starting cycle on each recurring start. If the compressor fails to start, the module will terminate the start attempt after 1 second and initiate a 3 minute lockout before attempting a restart. While the compressor is running, if supply voltage falls below the shutdown on low voltage limit for 2 seconds, SureStart will stop the compressor and initiate a 3 minute lockout. A restart will be initiated after 3 minutes if the supply voltage is equal to or greater than the minimum startup voltage. This is done to protect the compressor against a sudden drop in supply voltage. SureStart is able to detect an interruption in power, when the interruption is 0.1 seconds or longer. When a power interruption is detected, it will shut down the compressor for 3 minutes. A power interruption that is shorter than 0.1 seconds may result in the compressor running backwards. SureStart is able to determine if the compressor is running backwards. If this condition is detected, the control will stop the compressor for 3 minutes before restart is initiated. If the run capacitor is faulty or has failed, SureStart will shut down the compressor for 3 minutes before initiating a restart. SD-QS (12/16) Page 22

Figure 11. SureStart Mode of Operation SD-QS (12/16) Page 23

Flash Codes Single Phase LED Flash Codes A Red LED indicator will flash under the following conditions. [NOTE: LED fault indicator is turned off in normal running mode.] a) Rapid Flash (10 / sec) : Low Voltage b) Triple Flash Every Three Seconds (3 / 3 secs): Lockout on Three Failed Starts c) Slow Flash (1 / 3 secs): Lockout on Over Current d) Slow Steady Flash (1 / sec): Cycle Delay / Fault Mode Flash Code (Rapid Flash (10 / sec) : Low Voltage) - Displayed for Low supply voltage before or after a softstart. - If Low voltage is detected before a start, a re-start is attempted after 50 seconds. - If Low voltage is detected after a start, a re-start is attempted after 3 minutes. Flash Code (Triple Flash every three seconds (3 / 3 secs): Lockout on Three Failed Starts) - Displayed after failure to start on Three consecutive start attempts. - Re-start is attempted after 50 minutes. - Standard lockout period is revised to 3 minutes after a successful start. In circumstances where the compressor may have seized or is unable to startup due to failure of other components in the HVAC system, the software will check for three consecutive failed starts. On the third sequential failed start, the program goes into Lockout for 50 mins. On failing to get a good start even after 50 mins, it will re-attempt start again after duration of 50 mins. Once a good start is eventually achieved, it will reset the hardstart counter and will require 3 failed starts again to force it back into Lockout mode. Lockout can be cleared anytime through a power reset of the SureStart device. Flash Code (Slow Flash (1 / 3 secs): Lockout on Overcurrent) - Displayed for Overcurrent in running mode of the compressor motor. - Overcurrent limit is 25A for 08-16A version and 50A for 16-32A rated version. - Also displayed, if internal Klixon of the compressor trips out on overheat. - Re-start is attempted after 10 minutes. To limit the current in compressors from extending abnormally beyond its stated capacities, SureStart is also equipped with Overcurrent limit protection. For models rated from 16-32A, SureStart is designed to trip out in overload conditions exceeding 50A. In smaller models, it is designed to cutoff power to the compressor if the current drawn exceeds 25A. On overcurrent lockout, SureStart attempts a re-start automatically after 10 minutes. Both failed start lockout and overcurrent limit protection have been designed to prevent the compressor from drawing abnormal currents in conditions not feasible for the compressor operation. Flash Code (Slow Steady Flash (1 / sec): Cycle Delay / Fault Mode) - Displayed for Cycle delay between two consecutive softstarts or other faults mentioned below. - Re-start is attempted after a default period of 3 minutes. - Other possible reasons for this Fault mode indicator can be due to - incorrect wiring during installation, - a failed Softstart attempt, - intermittent power loss (duration longer than 100ms), - frequency out of range, or - failed run capacitor. SD-QS (12/16) Page 24

Flash Codes Three Phase A Red LED indicator will flash under the following conditions. [NOTE: LED fault indicator is turned off in normal running mode.] a) Reverse Phase: (1 / 2 secs) b) Fault Mode/Cycle Delay: (1 / 4 secs) c) Low Voltage/Over Voltage: 2 / 2 secs) Flash Code (Reverse Phase: (1 / 2 secs)) - Displayed if the supply Phase Sequence gets reversed before or after a start. - Re-start is attempted after 3 minutes. Flash Code (Fault Mode / Cycle Delay: (1 / 4 secs)) - Displayed for Cycle delay between two consecutive softstarts or other faults mentioned below. - Re-start is attempted after a default period of 3 minutes. - Other possible reasons for this Fault mode indicator can be due to - a failed Softstart attempt, - intermittent power loss (duration longer than 100ms), - frequency out of range Flash Code (Low Voltage / Over Voltage: (2 / 2 secs)) - Displayed for Low supply voltage or High supply voltage before or after a softstart. - If voltage is out of range before a start, a re-start is attempted after 50 seconds. - If voltage is out of range after a start, a re-start is attempted after 3 minutes. SD-QS (12/16) Page 25

6) Internal Heat Recovery System The SD compressor unit has a built-in heat recovery system which provides supplemental domestic water heating at a significant operating cost savings. The heat recovery system operates throughout the year to provide free hot water when operating in cooling mode and reduced cost hot wter when operating in the heating mode. The heat recovery system supplements hot water production, but does not replace the standard storage water heater sized for the application. The heat recovery system may be plumbed into an existing standard water heater as illustrated in Figure 12. Figure 12. Standard Storage Water Heater Service Connections Alternatively, the heat recovery system may be plumbed to the ETI Series GSTE storage water heater as shown in Figures 13a and 13b. The Series GSTE storage water heaters are preferred because the heat recovery system ports are designed to provide more efficient heat exchange within the storage water heater. SD-QS (12/16) Page 26

Figure 13a. GSTE Storage Water Heater - Service Connections Figure 13b. GSTE Storage Water Heater Tank Top View SD-QS (12/16) Page 27

The SD compressor unit internal heat recovery system contains a water high temperature control. It is factory set to 140 F. The heat recovery system also contains a refrigerant low temperature which is factory set to 130 F. Also, a freeze protection control is designed to operate the circulating pump when water temperature drops to 40 F, in order to provide water circulation independent of compressor operation. The GSTE storage water heaters are available in 60, 80 and 119 US gallon capacities, all of which have a 4.5 kw electric heating element, which provides the following recovery rates for increases in water temperature. ΔT 30 40 50 60 70 80 90 GPH 62 46 37 31 26 23 21 *ΔT in ºF; GPH in U.S. Gallons per hour. WARNING! The SD compressor unit and associated water piping must be in an environment maintained at a temperature of at least 40 F to avoid the potential freeze-up problems which can cause equipment failure and damage to the occupied structure. SD-QS (12/16) Page 28

Earth Loop Protection System 1) Anode Wire Installation Prior to this, the below grade installation of the DIRECT AXXESS Earth Loop System, including the Earth Loop Protection System anode and anode wire has been completed per the Earth Loop Protection Kit Manual, and at this point the anode wire is ready to be connected to the compressor unit. The earth loop protection system connection to the anode wire is on the back side of the compressor cabinet as illustrated in Figure 14, showing the electrical socket with the sealing cap. Figure 14. Compressor Cabinet Socket/Cap The EPS-KIT contains the plug connector, which will be field assembled and connected to the anode wire. WARNING! All power of the EarthLinked System is to be shut OFF at the disconnect while field wiring the Earth Loop Protection System. Failure to do so may result in serious injury or death, or equipment or property damage. The steps to install the anode wire to the plug connector assembly are as follows. Remove the sealing cap assembly tool from the compressor unit cabinet shown in Figures 14 and 15. Using the sealing cap assembly tool, as shown in Figure 15, unscrew the locking ring from the plug connector assembly to access the plug insert. Then, remove the gland nut, gland cage, and gland from the other end of the plug body as shown in Figure 15. SD-QS (12/16) Page 29

Figure 15. Disassembled Plug Connector SD-QS (12/16) Page 30

Strip the insulation from the multi-strand anode wire back approximately ¾ inch from the end and, while keeping the strands together, push the anode wire through the gland nut, gland cage, gland and plug body as shown in Figure 16. Loosen one of the two screw terminals on the plug insert to receive all of the strands of anode wire on one terminal. Figure 16. Anode Wire Insertion After inserting all strands of the anode wire into one of the terminals on the plug insert, tighten the wire in place by tightening the screw on that terminal. Once tightened, push the plug insert back into the plug body as shown in Figure 17 until it is firmly seated. Engage the locking ring with threads in the plug body and turn clockwise with the sealing cap assembly tool until the lock ring is firmly seated and tight against the plug insert. SD-QS (12/16) Page 31

Figure 17. Install the Plug Insert Slide the gland forward on the anode wire until it is firmly seated in the plug body as shown in Figure 18. Next, slide the gland cage over the gland, and slide the gland nut firmly against the gland cage, with the gland nut against the plug body. Engage the threads of the gland nut with those inside the plug body and manually thread the gland nut clockwise by hand. Figure 18. Engage the Gland Nut SD-QS (12/16) Page 32

Once the gland nut has been hand tightened into the plug body, use two adjustable wrenches to further tighten the gland nut until it is snug in the plug body as shown in Figure 19 and the anode wire is held firmly in the plug body and will not slip out. Do not over-tighten the gland nut! Figure 19. Secure the Anode Wire. After the plug and anode wire have been assembled, re-connect the sealing cap assembly tool to the socket on the compressor unit cabinet. After aligning the electrical contact pins, manually engage the threads on the plug locking cap with the threads on the socket and turn clockwise until the plug is firmly hand-tightened to the socket as shown in Figure 20. If the anode wire rises away from the compressor cabinet, be sure to shape a drip loop into the contour of the anode wire near the plug and socket. Figure 20. The Plug and Socket Joint After the plug and socket joint is secured, the power may be turned ON at the disconnect. SD-QS (12/16) Page 33

2) EPS Operation and Service Reference Figure 21 for the EPS components in the compressor unit electric box. Figure 21. Electric Box with EPS Components With power ON, and viewing the EPS Module in the compressor unit electric box, the EPS green light should be illuminated, indicating there is power to the EPS system. If the green light is NOT illuminated, verify that 208/230 volt power is available to the EPS power supply. Also check the fuse. Check and replace, as appropriate, the fuse for the EPS Power Supply as shown in Figure 21. For service purposes, a spare fuse has been factory supplied and is located in the electrical box. The replacement fuse is Littlefuse 213 Series Slo-Blo rated at 250 Volts, 2 Amperes, P/N 0213002MXP. This is also Allied Electronics Stock Number R1090710. If 208/230 volt power is available and the fuse is intact, contact ETI technical support at 1-863-701-0096. If there is an opening in the earth loop electrical circuit, the audible signal will be heard. After shutting power OFF, all electrical connections from the EPS module to the earth loop system should be checked and adjusted as appropriate to ensure good electrical contact. NOTE: In extremely dry soil conditions (with low conductivity), the EPS system might not close the alarm relay upon initial start-up or after an interruption in power. Resetting the alarm relay can be done by quickly shorting the anode, positive to ground. It may be necessary to strip away part of the anode wire insulation to do so. If it is necessary to operate the heating and cooling system while the EPS is down for service, the EPS power may be temporarily disengaged to eliminate the audible alarm, by removing the EPS/EDM Fuse shown in Figure 21. Please note this step also de-energize the EDM system. Upon completion of servicing the EPS, replace the fuse to energize the EPS and EDM systems and maintain warranty coverage. The EPS board is not field serviceable. SD-QS (12/16) Page 34

IMPORTANT! DO NOT troubleshoot the EPS board! If the above steps do not resolve the problem, call ETI for technical service assistance at 1-863-701-0096. 3) Voltage Verification If it is necessary to verify the voltage output of the EPS system, it can be checked with a digital DC voltmeter. The correct electrical voltage is listed in Figure 22. State of system Unloaded (Anode or Ground disconnected, alarm sounding) Voltage Output 20-30 V DC Figure 22. EPS Voltage Ratings To check the voltage unloaded, disconnect the Anode plug from the back of the Compressor Unit. The EPS alarm will be heard. While the alarm is sounding, use one end of the voltmeter probe into the EPS socket, and put the other voltmeter probe in contact with either the earth loop liquid or the vapor line. Make sure the probe is in contact with the copper, with no insulation in the way. As an alternative you can also use the service valve. See Figure 23. Reconnect the Anode, alarm should stop ringing. NOTE: In extremely dry soil conditions (with low conductivity), the EPS system might not close the alarm relay upon initial start-up or after an interruption in power. Resetting the alarm relay can be done by quickly shorting the anode, positive to ground. It may be necessary to strip away part of the anode wire insulation to do so. Figure 23. Typical Test for DC Voltage SD-QS (12/16) Page 35

Start-Up Process 1) System Leak Check After all indoor and outdoor refrigerant bearing components of the system have been installed and joints have been nitrogen brazed, pressurize the system prior to evacuation to leak test the system. Do not exceed 150 psig when pressure testing the compressor unit and indoor system components. Test for leaks with a sensitive electronic leak detector and bubble solution. Repair leaks as appropriate prior to evacuation. Evacuation and charging of the system is done through the compressor unit. All of the refrigerant containing components in the compressor unit are illustrated in Figures 24 and 25. The Start-up Process is illustrated in Figure 32. CAUTION! During the Evacuation and Initial Charging processes, be sure that ALL power to the EarthLinked System is OFF. This includes the compressor unit, air handler and all other electrically powered system components. Failure to do so will cause lockout on start-up. SD-QS (12/16) Page 36

Figure 24. SD Internal Flow Schematic SD-QS (12/16) Page 37

Figure 25. SD Piping SD-QS (12/16) Page 38

2) Evacuation Refer to Figure 26 and the following procedure: 1. Carefully vent any pressurized nitrogen charge from the compressor unit and system. 2. After venting the pressurized system, use a good quality gauge manifold and a non-permeable hose set as shown in Figure 26. If possible, use two Schrader core removal tools. Install one on the discharge line access port and the other on the initial charging port. Removal of the Schrader cores will reduce the time to achieve the desired vacuum. 3. Attach a good quality digital vacuum gauge with an isolation valve to the liquid line service valve access port as shown in Figure 26. 4. Use a well maintained, high quality vacuum pump with an isolation valve, rated at 7 cfm or greater, connected to the gauge manifold. Ensure that the vacuum pump oil has been changed prior to initiating the evacuation process to avoid contamination. 5. Fully open the LP and HP valves and both service valves. Reference Figure 26. IMPORTANT! DO NOT ENERGIZE THE COMPRESSOR WHILE THE SYSTEM IS UNDER VACUUM. THIS WILL CAUSE DAMAGE TO THE COMPRESSOR. 6. Open the vacuum pump isolation valve and start the pump. Evacuate the system down to 400 MICRONS or less as read on the digital vacuum gauge. After 400 microns or less has been achieved, isolate the vacuum pump. Wait 5 minutes and read the digital vacuum gauge. The system pressure must not exceed 500 MICRONS WITHIN 15 MINUTES. If it does, continue the evacuation to remove any remaining non-condensibles in the system. A dry system will hold 500 microns for 15 minutes. A procedure often used to evacuate a system, known as the triple evacuation method, is detailed in the section of this manual entitled Triple Evacuation. Local codes may require other evacuation criteria, in which case the local codes take precedence over the evacuation requirements described above. IMPORTANT! DO NOT CHARGE THE SYSTEM UNTIL THE CONDITIONS OF STEP #6 ARE COMPLETED! 7. When the system has been successfully evacuated, close the LP and HP valves on the manifold gauge set. Do not remove the manifold gauge set or hoses, as air will be drawn into the system and defeat the evacuation process. SD-QS (12/16) Page 39

Figure 26. Evacuation of SD System SD-QS (12/16) Page 40

3) Initial Charge 1. Disconnect the vacuum pump and isolate the digital vacuum gauge. Connect the refrigerant container to the charging hose of the manifold gauge set as shown in Figure 27. WARNING! Inhalation of high concentrations of refrigerant gas vapor is harmful and may cause heart irregularities or death. Vapor reduces oxygen available for breathing and is heavier than air. Decomposition products are hazardous. Liquid contact can cause frostbite. Avoid contact of liquid with eyes and prolonged skin exposure. Liquid and gas are under pressure. Deliberate inhalation of refrigerant gas is extremely dangerous. Asphyxiation can occur without warning due to lack of oxygen. Before using, read the material safety data sheet. Use proper safety measures when charging the system, especially when warming the refrigerant container. Do not overheat. 2. Place the refrigerant container upside down (or oriented to deliver liquid refrigerant), with the refrigerant valve at the bottom, on the scale, as shown in Figure 27. Purge the charging hose by loosending it at the manifold end, until refrigerant is released. Tighten the charging hose and zero out the refrigerant scale. 3. Open the LP valve on the manifold gauge set. Opening the refrigerant container valve sends liquid refrigerant through the initial charging port into the system. Continue to add refrigerant until 3 pounds per ton of system capacity has been added. In cold weather, it may be necessary to warm the refrigerant container to charge to 3 pounds per ton. 4. After completing the initial refrigerant charge to the system, turn the LP valve off, re-install the Schrader valve core into the initial charging port, remove the tool, and install the Schrader valve cap firmly on the Schrader valve. SD-QS (12/16) Page 41

Figure 27. Initial Charge of SD System SD-QS (12/16) Page 42

4) Final Charge 1. Remove the Schrader core tool from the hose just taken off of the initial charging port. 2. Crack open the LP valve on the manifold gauge set so that a small amount of refrigerant gas flows to purge the hose. Connect the hose to the final charging port, shown in Figure 28. Tighten the hose to the final charging port and turn off the LP valve when the hose connection is secure. 3. Start the system in heat mode. Disconnect the control wire from the O terminal to ensure the system remains in the heat mode during the final charging process. In an air system, the design (and minimum) air flow is 400 cfm per nominal ton. In a hydronic system, the design (and minimum) circulating water flow to 3 gpm per nominal ton. As installed, higher than design air and circulating water flows are acceptable, recognizing that this will cause greater power consumption by the air handler and circulating pump motors. IMPORTANT! All refrigerant to air systems must be charged in air heating mode only. Never adjust the refrigerant charge while in cooling mode. 4. Slowly open the LP valve on the manifold gauge set and add refrigerant just fast enough to maintain the suction pressure. 5. While still weighing refrigerant, slowly add refrigerant until liquid refrigerant is clearly seen in the middle sight glass of the ACC, as shown in Figure 29. 6. Shut the LP valve on the manifold gauge set and run the system for 20 minutes to ensure that the refrigerant liquid level remains at the middle slightly glass. If the liquid refrigerant level drops below the middle sight glass during this time, slowly add refrigerant until the liquid level stabilizes at the middle sight glass. 7. With the liquid refrigerant level at the middle sight glass, attach and insulate a temperature clamp or probe securely to the earth loop vapor line at the compressor unit service valve shown in Figure 28. Read the measured temperature. Also read the LP gauge pressure on the manifold gauge set. Use a pressure/temperature chart (Figure 31) to verify that the system is operating at saturation, meaning that no superheat is measured on the earth loop vapor line. To verify this, the measured vapor line temperature should be within ± 3 F of the saturation temperature read from the chart for the measured LP gauge pressure. If the measured temperature is out of this range, contact ETI technical support at 1/863-701-0096. 8. After verifying that the system is operating at saturation in heating mode, and with the system still operating in heating mode, slowly open the LP valve on the manifold gauge set, and slowly add refrigerant to the system until the refrigerant liquid level is at, but not above, the top ACC sight glass, as shown in Figure 30. At no time should the refrigerant liquid level be above the top ACC sight glass. 9. The system is now fully charged. Document the weight of the Total refrigerant charge in the system. Write it down on the Warranty Registration Card and inside the compressor unit on the electrical diagram, for future reference. 10. Re-connect the control wire to the O terminal. The system is now operational in heating and cooling modes. SD-QS (12/16) Page 43

Figure 28. Final Charge of SD System SD-QS (12/16) Page 44

Figure 29. Charging to the Middle Sight Glass(Heat only units) Figure 30. Final charging to the Top Sight Glass(Heat/Cool units) SD-QS (12/16) Page 45

TEMPERATURE ( F) PRESSURE (psig) -20 26.1-15 30.8-10 35.9-5 41.5 0 47.5 5 54.1 10 61.2 15 68.8 20 77.1 25 86.0 30 95.5 35 105.7 40 116.6 45 128.3 50 140.8 55 154.1 60 168.2 65 183.2 70 199.2 75 216.1 80 234.0 85 253.0 90 273.0 95 294.1 100 316.4 105 339.9 110 364.6 115 390.5 120 417.7 125 446.3 130 476.3 135 507.6 140 540.5 145 574.8 150 610.6 Figure 31. Pressure-Temperature for R-410A SD-QS (12/16) Page 46

Figure 32. Start-Up Process SD-QS (12/16) Page 47

Troubleshooting CAUTION! SERVICE MAY BE PERFORMED ONLY BY AN EARTHLINKED TECHNOLOGIES AUTHORIZED PROFESSIONAL HVAC OR REFRIGERATION SERVICE PERSON. USE ONLY SAFE AND APPROVED SERVICE TECHNIQUES. IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, MAINTENANCE OR SERVICE CAN CAUSE 1) THE EARTHLINKED SYSTEM OR COMPONENTS TO MALFUNCTION AND OR FAIL, 2) PROPERTY DAMAGE, INJURY OR DEATH. IMPORTANT! EarthLinked Refrigerant System Safety Switches EarthLinked compressor units are equipped with the following three safety switches that will turn the compressor off if the following limits are exceeded. High Pressure Switch: Located between the compressor discharge port and the reversing valve, the cut-out pressure is 600 psig. This is a manual reset switch. Low Pressure Switch: Located between the ACC and the compressor suction port, the cut-out pressure is 25 psig. This is an automatic reset switch. Discharge Temperature Switch: Located on the compressor discharge line, the cut-out temperature is 240 F. This is a manual reset switch. If you experience difficulties with the EarthLinked system, please review the appropriate section of the manual. It may be helpful to have another professional HVAC or ETI approved refrigeration service person review and check it with you. Time and expense can be saved by taking a thoughtful and orderly approach to troubleshooting. Start with a visual check: Are there loose wires, crimped tubing, missing parts, etc? 1) Compressor After setting the remote (wall) thermostat system switch to the OFF position and the thermostat fan switch to the AUTO position, proceed to check the supply voltage at (1) the line terminals to the breaker/disconnect; 2) the system side of the breaker/disconnect, and 3) the line-side of the transformer. Verify the proper voltage rating for the system. Reference Figure 33. SD-QS (12/16) Page 48

Figure 33. Compressor Unit Voltage Information The following compressor checklist is provided to analyze the compressor and determine if it is operating properly or if it is faulty: 1. Electrical Service Panel turn power off. a. Check circuit terminal connections for tightness b. Circuit breaker sized right? c. Wire size correct? (check NEC or local codes) 2. Check capacitor or other start components for visible bulges, leaks, overheating or loose wire connections. 3. Test capacitor and start components and replace if necessary. Capacitors can be checked by substitution or with capacitance meter. OK if reads ±10% of the manufacturer s specification. 4. Check incoming power supply voltage to determine whether it is within acceptable voltage range. (See Figure 33) 5. Check voltage at compressor unit terminals to determine whether it is within acceptable voltage range. (See Figure 33) 6. Running Amperage. Connect a clip-on type ammeter to the (common) lead to the compressor. Turn on the supply voltage and energize the unit. The compressor will initially draw high amperage; it should soon drop to the RLA value (See Figure 7) or less. If the amperage stays high, check the motor winding resistance and/or run capacitor. SD-QS (12/16) Page 49

Note: Carefully feel the top of the compressor to see if it has overheated. If it is hot, the internal overload may be open. You may have to wait several hours for it to reset before proceeding. If the compressor draws a high amperage and does not start (amperage is approximately locked rotor amperage LRA (See Figure 7)), the compressor is locked mechanically and should be removed from the system and replaced. Verify before removing! 7. Motor Circuit Testing Using a digital volt-ohmmeter (VOM), measure the resistance across the compressor windings terminals as shown in Figure 34. The power leads to the compressor must be disconnected before taking an electrical measurement. A good rule of thumb for single phase compressors is that start winding resistance (R 2 ) is 3 to 5 times greater than run winding resistance (R 1 ). Figure 34. Compressor Motor Circuit Testing SD-QS (12/16) Page 50

8. Grounded Windings Test the compressor motor for a grounded winding. The check should be made using an ohmmeter capable of measuring very high resistance on a VOM. The resistance between windings and the housing is one million to three million ohms for an ungrounded winding. Attach one lead to the compressor case on a bare metal tube or ground terminal, and to each compressor terminal as shown in Figure 35. A short circuit at a high voltage terminal indicates a motor defect (grounded). Figure 35. Compressor Motor Grounded Winding Test 9. Compressor not pumping. Connect gauge block hoses to the suction and discharge pressure ports in the compressor unit. Read pressure gauges to affirm that system is pressurized with refrigerant. Turn on power to compressor unit and run unit. Observe pressure gauges. If pressures on both gauges remain the same, compressor is not pumping and there is a possible internal failure. See System Troubleshooting Chart. SD-QS (12/16) Page 51

2) System Problem / Symptom A. System does not run. Note: Some digital thermostats have a built-in five-minute time delay. B. System runs for long period or continuously. C. System blows fuses or trips circuit breaker. Likely Cause(s) Action/Correction 1. Thermostat fault. 1. Adjust thermostat settings. / Replace thermostat. 2. Power supply problem (AHU / compressor unit). 2. Check power supply for adequate phase and voltage. Check wiring to system and external breakers or fuses. 3. Control voltage problem. 3. Check for 24V on terminal strip between R and C terminals. 4. Shut off by external thermostat or thermostat is defective. 5. System lockout: System off on high pressure / low pressure switches or discharge temperature switch. 6. Internal component or connection failure. 7. Compressor contactor not pulling in. 8. Faulty run capacitor or start components. 9. Compressor windings shorted or grounded. 10. SureStart fault 11. Nano-PLC fault 4. Check operation of thermostat. 5. Reset limit switch. Analyze system for root cause. Check between Common and X terminal for 24V, indicating a lock-out condition. Reset if necessary by disabling the unit 24V control power momentarily. 6. Check for loose wiring. Check components for failure. 7. Check for 24V across contactor. Trace 24V circuit and components between Y and C to locate fault. Repair or replace as necessary. 8. Test each and replace as necessary. 9. See compressor diagram/ replace the compressor. Replace filter drier and run capacitor. 10. Check the SureStart to see if the red LED is flashing. Flashing codes are in section Installation 7) SureStart of this manual. 11. With thermostat calling, verify the inputs and outputs of the Nano- PLC following the wiring diagram. Contact tech support 1. Thermostat fault. 1. Adjust thermostat settings / Replace thermostat. 2. Refrigerant undercharged. 3. Component failure. 4. Outdoor thermostat not connected or failed (heating mode). 5. Reduced air flow. 6. Four-way reversing valve is short circuiting refrigerant and bypassing hot gas to suction. 2. Repair leak and replace filter drier. Evacuate and recharge system. 3. Check pressures and electrical circuits for abnormalities. 4. Check outdoor thermostat and electric supplemental heat operation. Confirm proper wiring. 5. Check air ducts for leaks and repair. Check blower operation. Check air filter(s). Remove air flow restrictions (min.400 CFM/ton). 6. Replace four-way reversing valve and filter drier, evacuate, recharge and start-up system. 7. Unit undersized. 7. Contact ETI Technical Support at 863-701-0096. 1. Inadequate circuit ampacity. 2. Short, loose or improper connection in field wiring. 1. Note electrical requirement and correct as necessary. 2. Check field wiring for problems. Figure 36. System Troubleshooting Chart SD-QS (12/16) Page 52