MXSU - Selection table 3-core Kits / X-section

MXSU - Selection table 3-core Kits / X-section Voltage Cables with wire screen Uo/U (Umax) Kit-number Appl. range (based on Al/rm) 6/10 (12) MXSU 3311 1x 35-95 MXSU 3331 1x 95-240 8.7/15 (17.5) MXSU 4311 1x 50-95 MXSU 4331 1x 120-240 12,7/22 (24) MXSU 5311 1x 35-95 MXSU 5331 1x 95-240 BDG/THT 08/2000 16

MXSU - Selection table 3-core cable dimensions Conductor Ø Core Insulation Ø Outer Cable Ø Connector min max min max min max Ø max length max. Kit Number mm mm mm mm mm mm mm mm MXSU-3111 6,5 12,0 14,4 21,8 42,5 61,0 23,0 85,0 MXSU-3131 11,0 19,2 19,3 29,4 53,0 77,0 33,0 125 MXSU-4111 6,5 12,0 23,0 31,6 59,0 78,5 23,0 85,0 MXSU-4131 11,0 19,2 18,0 24,0 50,0 62,0 33,0 125 MXSU-5111 6,5 12,0 19,0 26,0 52,5 71,5 23,0 85,0 MXSU-5131 11,0 19,2 23,5 33,6 62,5 89,0 33,0 125 BDG/THT 08/2000 17

11kV SINGLE CORE AND 3 CORE JOINTS PLASTIC INSULATED CABLE 25 35 50 70 95 120 150 185 240 300 400 500 630 SINGLE CORE EPKJ-17A/1XU-1XU MXSU-3111 EPKJ-17B/1XU-1XU MXSU-3131 OVERLAP EPKJ-17C/1XU-1XU MXSU-3141 EPKJ-17D/1XU-1XU THREE (3) CORE EPKJ-17A/3XU-3XU EPKJ-17B/3XU-3XU EPKJ-17C/3XU-3XU MXSU-3311 MXSU-3331 OVERLAP MXSU-3341 EPKJ-17D/3XU-3XU 25 35 50 70 95 120 150 185 240 300 400 500 630 CROSS SECTIONAL AREA IN SQMM OVERLAP KITS ADJACENT TO THIS RANGE, BOTH OVERLAP THIS RANGE.

22kV SINGLE CORE AND 3 CORE JOINTS PLASTIC INSULATED CABLE 10 16 25 35 50 70 95 120 150 185 240 300 400 SINGLE CORE EPKJ-24A/1XU-1XU EPKJ-24B/1XU-1XU MXSU-5111 EPKJ-24C/1XU-1XU MXSU-5131 OVERLAP EPKJ-24D/1XU-1XU MXSU-5141 THREE (3) CORE EPKJ-24A/3XU-3XU EPKJ-24B/3XU-3XU MXSU-5311 EPKJ-24C/3XU-3XU MXSU-5331 EPKJ-24D/3XU-3XU 10 16 25 35 50 70 95 120 150 185 240 300 400 CROSS SECTIONAL AREA IN SQMM OVERLAP KITS ADJACENT TO THIS RANGE, BOTH OVERLAP THIS RANGE.

33kV SINGLE CORE AND 3 CORE JOINTS PLASTIC INSULATED CABLE 35 50 70 95 120 150 185 240 300 400 500 630 SINGLE CORE EPKJ-36A/1XU-1XU MXSU-6111 EPKJ-36B/1XU-1XU MXSU-6131 EPKJ-36C/1XU-1XU MXSU-6141 EPKJ-36D/1XU-1XU THREE (3) CORE EPKJ-36A/3XU-3XU EPKJ-36B/3XU-3XU EPKJ-36C/3XU-3XU 35 50 70 95 120 150 185 240 300 400 500 630 CROSS SECTIONAL AREA IN SQMM OVERLAP

R EAKJ Airfield lighting cable joints Heat-shrinkable airfield lighting cable joints for screened and unscreened cables 6/10 (12) kv and 3,6/6 (7,2) kv FEATURES High performance joint material Compact design Connector included BENEFITS Applicable for 4 kv and 7 kv lighting systems Easy and safe installation Unlimited shelf life

Design Void filler and stress grading material Stress control tubing Outer sleeve Void filler and stress grading material Connectors Screened insulating tubing Copper mesh Technical data Voltage Cross-section Cable EAKJ-12A/1XU-1XU 6/10 (12) kv 6 mm 2 single core screened EAKJ-2257 3,6/6 (7,2) kv 6 mm 2 single core unscreened Test sequence Minimum performance of the EAKJ 12A 1XU-1XU Airfield Lighting Cable Joint in accordance with Raychem PPS 3013/3016 Master Specification. Test Test requirements A.C. voltage withstand 50 Hz 5 min at 35 kv Partial discharge XLPE 3 pc @ 7,5 kv XLPE 10 pc @ 12,0 kv Impulse voltage withstand 10 positive impulses @ 75 kv 1,2/50 µs impulse 10 negative impulses @ 75 kv D.C. voltage withstand 30 min @ 48 kv Partial discharge XLPE 3 pc @ 7,5 kv XLPE 10 pc @ 12,0 kv Test report PPR 1340 A simple fast jointing technique The joint components are supplied as a preengineered set of heat-shrinkable tubings. Cable preparation and installation techniques on the EAKJ are identical with medium voltage jointing systems. The cross-linked polymeric materials provide highest performance also on smallest cross sections. The long-term performance of Raychem s heat shrinkable materials has been well proven by millions of jointing systems up to 72 kv. At Raychem we are committed to continuous quality improvement in every aspect of our business. Internet: www.raychem.com R All the above information, including drawings, illustrations and graphic displays, reflects our present understanding and is to the best of our knowledge and belief correct and reliable. It does, however, under no circumstance constitute an assurance of any particular qualities. Such an assurance is only provided in the context of our product specifications. Our liability for this product is set forth in our standard terms and conditions of sale. Raychem is a trademark of Raychem Corporation. Raychem GmbH Energy Networks Haidgraben 6 85521 Ottobrunn Munich, Germany Tel. (089) 6089-0 Raychem Corporation Energy Networks 8000 Purfoy Road Fuquay-Varina, NC 27526-9349, U.S.A. Tel. (800) 327-6996 Raychem Singapore Pte Ltd. Energy Networks 438 Alexandra Road # 05-01 Alexandra Point Singapore 119958 Tel. 65-2774138 Raychem EPP 0796 8/99

R EPKB Heat-shrinkable medium voltage branch joints for single core polymeric cables up to 36 kv Features Shear bolt connector Connector and insulation in one kit Range taking kit Compact, robust and buriable Benefits No special installation tools or dies needed No other engineering required Wide range of application Space saving, low total costs

EPKB Heat-shrinkable medium voltage branch joints for single core polymeric cables up to 36 kv Today s networks must achieve higher levels of reliability and flexibility to meet the demands of their operators who are under increasing pressure to decrease the networks costs. The result is that engineers are looking at new ways to optimize the configuration of their networks. In response to these demands Raychem has developed a range of easy to install, medium voltage branch joints for single core polymeric cables. EPKB joints use shear bolt connectors to simplify the interconnection of conductors. Heat-shrinkable insulating components supply pre-engineered thicknesses of insulation and stress control material. This is a major step forward in comparison with traditional taping solutions. Network applications The long-term reliability of polymeric cables in combination with modern fault finding techniques has opened up many economically attractive opportunities for solid branch joint connections. The branch joints are sealed in robust heatshrinkable jackets and are suitable for direct burial which saves valuable space in comparison with traditional link boxes or switchgear. EPKB branch joints can also be used to reduce the amount of cables required for making connections to transformers remote from the distribution ring. Raychem s flexible solution Given the difficulties of both connecting the conductor and providing the insulation for the more complex geometry of a branch joint, Raychem s solution provides a complete kit including both connector and insulation. Many of the joint s basic components are already used in Raychem s heat-shrinkable elastomeric joints proven in millions of installations all over the world. The heart of the insulation is a thick-wall elastomeric tubing designed to conform tightly with the stress control system and the connector. Special features The design of the connector, specially engineered to fit the insulation components, also enables the user to connect different conductor sizes. This provides great flexibility in the range of cables which can be connected in this branch joint. The connector uses bolts designed to shear off at a preset level of torque and is installed with a standard socket set. This technique ensures that the connector performs consistently for a wide range of conductor diameters. As the installation of the complete joint is similar to the installation of a heat-shrinkable inline joint, time requirements are low and no additional installer skills are needed. The complete kit has been tested to meet Raychems performance standards. For performance specifications and available sizes please see last page.

Electrical stress control The mechanical connector is covered with yellow void filler tape and JSCR stress control tubing. These are the same materials used in Raychem s inline medium voltage joints. Spacer profile This specially extruded profile is made from a red high-performance insulating elastomer. The material properties guarantee a void-free crutch filling and tight electrical interfaces between the two branch cables. Breakout cap The adhesive coated two finger breakout provides watersealing for the branch side in the same way as the jacket does for the single side. This also gives the flexibility needed to ensure good sealing under temperature changes due to load cycling.

EPKB Minimum performance of Raychem branch joints for screened polymeric cables up to 24 kv Test Sequence Test Voltage Result Highest Voltage for Cable U m (kv) 12/17 24 A.C. Voltage Withstand 1 min 25 55 no breakdown Partial Discharge 12 24 20 pc Impulse Voltage Withstand 10 positive and 10 negative, 1.2/50 µs, 95 150 no breakdown between conductor and grounded screen Load Cycling 63 cycles 15 30 no breakdown 5 h heating, 3 h cooling Conductor temperature on XLPE cables: 95 Partial Discharge 12 24 20 pc Thermal Short Circuit 1 s symmetrical fault with conductor temperature no functional as in the cable specification damage Load Cycling as above, with cable in 1 m water 15 30 no breakdown (oversheath removed) Partial Discharge as above 12 24 20 pc A.C. Voltage Withstand 4 h 24 48 no breakdown Impulse Voltage Withstand repeat 95 150 no breakdown D.C. Voltage Withstand 30 min 48 96 no breakdown Notes: 1. U m is the highest phase to phase voltage. All other voltages are stated as phase to ground values. 2. Further details are given in Raychem specification PPS 3013. Selection Table Voltage Conductor Overall cable Min. diameter over EPKB class cross-section diameter insulation of main cable kit description kv mm 2 min max 35-95 23.5 32 14.8 EPKB 12A 1XU-2XU 12 95-150 26.0 37.5 19.3 EPKB 12B 1XU-2XU 185-300 32.1 43 23.9 EPKB 12C 1XU-2XU 35-95 25.2 38 19.0 EPKB 24A 1XU-2XU 24 95-150 31.8 40 23.5 EPKB 24B 1XU-2XU 185-300 36.4 47 28.1 EPKB 24C 1XU-2XU For other combinations of cable sizes or information for 36 kv cables, please contact your local Raychem representative. All of the above information, including drawings, illustrations and graphic designs, reflects our present understanding and is to the best of our knowledge and belief correct and reliable. Users, however, should independently evaluate the suitability of each product for the desired application. Under no circumstances does this constitute an assurance of any particular quality or performance. Such an assurance is only provided in the context of our product specifications or explicit contractual arrangements. Our liability for these products is set forth in our standard terms and conditions of sale. AMP, Dulmison, Hellstern, Raychem, and SIMEL are trademarks of Tyco International Ltd. Argentina Phone: ++54-11-4733 2277 Fax: ++54-11-4733 2267 Australia Phone: ++61-2-4390 1111 Fax: ++61-2-4353 2497 Brazil Phone: ++55-11-861 1311 Fax: ++55-11-861 1862 Canada Phone: ++1-905-475 6222 Fax: ++1-905-470-4453 France Phone: ++33-3-80583200 Fax: ++33-3-80341015 Mexico Phone: ++52-5-729 0405 Fax: ++52-5-361-8545 Thailand Phone: ++66-2-7394026-32 Fax: ++66-2-3260563-64 United States of America Phone: ++1-800-327-6996 Fax: ++1-800-527-8350 Tyco Electronics EPP 0754 11/00 www.tycoelectronics.com Tyco Electronics Raychem GmbH Energy Division Haidgraben 6, 85521 Ottobrunn/Munich, Germany Phone: ++49-89-6089-0, Fax: ++49-89-6096345

EPKE Live End Seals for 12 and 24 kv single core plastic cable EPKE Live End Seals for Enhanced Cable Protection The EPKE product line includes nine different end seal kits covering an application range from 70 to 500 mm 2. No special crimping tools are required for the installation. The cable can be energized immediately after installation. Third party damage to cable can be caused by heavy vehicles, such as excavation machinery, etc., during construction work. The live end seals allow partially installed networks to be energized, and therefore enable the detection of third party damage as soon as it occurs. The end seal also protects the cable against moisture ingress. Design and Function of the Product The end seal is designed to fit most 12 and 24 kv single core plastic cables with screen wire or tape shielding which meet IEC, VDE and BS. It has been tested in accordance with Raychem specification PPS 3013. The cable is prepared as for a standard joint. Each end seal kit is designed to fit a specific conductor size. At the core of the kit is an insulating rod with a bore to fit the end of the conductor. The composite rod is slid over the conductor. Stress grading mastic is applied to the cable screen cut and the composite rod screen before the stress control tube is shrunk down. The electrical insulation is provided by a screened composite insulating tube which is then shrunk in place over the stress control tube. This tube is shielded by copper mesh and connected to the earth wires. The entire end seal is covered with an insulating outer sealing sleeve. Features A full product line with nine different sizes. Suitable for both wire and tape shielded cables. Installation requires no need of special tools. (e.g. crimps, etc) Same insulation technology as Raychem joints. Benefits Covers all commercial cable sizes. Fits most plastic single core cable types. Protects cable against moisture ingress. Enables detection of third party damage. Energizing can take place immediately after installation. R

EPKE Live End Seals for 12 and 24 kv single core plastic cable Wire shielded cables Tape shielded cables Selection table Voltage class Kit description Cable cross Overall Uo/U section (mm 2 ) length (mm) EPKE 24B / 1XU- 70 70 400 EPKE 24B / 1XU- 95 95 400 EPKE 24C / 1XU-120 120 400 EPKE 24C / 1XU-150 150 400 6,9/12 and 13,8/24 kv EPKE 24C / 1XU-185 185 400 Installation Instruction EPP 0690-2/97 EPKE 24C / 1XU-240 240 400 EPKE 24D / 1XU-300 300 400 EPKE 24D / 1XU-400 400 400 EPKE 24D / 1XU-500 500 400 All of the above information, including drawings, illustrations and graphic designs, reflects our present understanding and is to the best of our knowledge and belief correct and reliable. Users, however, should independently evaluate the suitability of each product for the desired application. Under no circumstances does this constitute an assurance of any particular quality or performance. Such an assurance is only provided in the context of our product specifications or explicit contractual arrangements. Our liability for these products is set forth in our standard terms and conditions of sale. ALR, AMP, AXICOM, B&H, Bowthorpe EMP, Critchley, Dorman Smith, Dulmison, Hellstern, La Prairie, Morlynn, Raychem, SIMEL and SUCOFIT are trademarks. Argentina Phone: ++54-11-4733 2277 Fax: ++54-11-4733 2267 Australia Phone: ++61-2-4390 1111 Fax: ++61-2-4353 2497 Brazil Phone: ++55-11-3611 1862 Fax: ++55-11-3611 2457 Canada Phone: ++1-905-475 6222 Fax: ++1-905-470-4453 France Phone: ++33-3-80583200 Fax: ++33-3-80341015 Mexico Phone: ++52-5-729 0405 Fax: ++52-5-361-8545 Thailand Phone: ++66-2-7394026-32 Fax: ++66-2-3260563-64 United States of America Phone: ++1-800-327-6996 Fax: ++1-800-527-8350 United Kingdom Phone: ++44-1772-325400 Fax: ++44-1772-726276 Tyco Electronics Raychem GmbH Energy Division Haidgraben 6, 85521 Ottobrunn/Munich, Germany Phone: ++49-89-6089-0, Fax: ++49-89-6096345 http://energy.tycoelectronics.com Tyco Electronics EPP 0707 11/01