TSL-Aerofoil wall mounted basin installation + maintenance
contents 3 Contents 4 Technical Data 5 Before You Install 8 Assembly 11 How to Install 14 Maintenance 15 Cleaning 17 Warranty 18 Contact Details 2 TSL-AEROFOIL WALL MOUNTED BASIN manual
contents LENGTH 600 1200 1800 2400 ParTS P1 Washplane 1 1 1 1 P2 Main body 1 1 1 1 P3 Cantilever 1 1 1 1 P4 Main body end cap LH 1 1 1 1 P5 Main body end cap RH 1 1 1 1 P6 Cantilever end cap LH 1 1 1 1 P7 Cantilever end cap RH 1 1 1 1 P8 Clamping foot 2 3 4 5 P9 Wall fixing plate 2 3 4 5 P10 Leg 2 3 4 5 P11 Foot Cap 2 3 4 5 P12 Adjustable foot 2 3 4 5 P13 Seal 2 2 2 2 P14 Rubber gasket 1 1 1 1 P15 Grate 1 2 3 4 P16 Lovair Waste 1 2 3 4 P17 Sealing strip Fixings F1 M5x12 countersunk screw 8 8 8 8 F2 M8x12 countersunk screw 4 6 8 10 F3 M6x14 Pan head 2 3 4 5 F4 M8x12 cone point 2 2 2 2 F5 M8 tee nut 4 6 8 10 F6 M6 tee bolt 12 20 28 36 F7 Washer 14 23 32 41 F8 M6 nut 12 20 28 36 f9 Fixing tape 1 1 1 1 Additional requirements not supplied by The Splash Lab A1 Silicone 1 1 1 1 A2 Wall fixings 6 9 12 15 TSL-AEROFOIL WALL MOUNTED BASIN manual 3
technical data Finishes Marble Length users Codes Sink weight (kg) Frame weight (kg) Total weight (kg) 600mm 1 TSL-101MB 26.00 11.00 37.00 1200mm 2 TSL-102MB 51.00 21.00 72.00 1800mm 3 TSL-103MB 76.00 29.50 105.50` 2400mm 4 TSL-104MB 101.00 38.00 139.00 Solid Surface Length users Codes Sink weight (kg) Frame weight (kg) Total weight (kg) 600mm 1 TSL-101SL 15.00 11.00 26.00 1200mm 2 TSL-102SL 29.00 21.00 50.00 1800mm 3 TSL-103SL 43.00 29.50 72.50 2400mm 4 TSL-104SL 57.00 38.00 95.00 Quartz Length users Codes Sink weight (kg) Frame weight (kg) Total weight (kg) 600mm 1 TSL-101QZ 24.00 11.00 35.00 1200mm 2 TSL-102QZ 46.50 21.00 67.50 1800mm 3 TSL-103QZ 69.00 29.50 98.50 2400mm 4 TSL-104QZ 92.00 38.00 130.00 Warranty Material Mounting frame 5 years from date of purchase (terms and conditions apply) Solid surface Marble Quartz Aluminium and powder-coated steel 4 TSL-AEROFOIL WALL MOUNTED BASIN manual
before you install + + The Aerofoil has been designed to fit within a 92mm wall cavity, check to make sure that the void is at least 92mm before installation. + + Must be fixed to a suitable wall substrate to allow for the correct use of the Aerofoil. The Splash Lab recommend that installers contact a fixings specialist for advice to ensure the correct fixings are used for the location. Wall fixings are not included with the aerofoil. + + If the void is less than 92mm or wall construction not suitable for fix the Aerofoil t, an additional wall cavity will have to be created. + + Access will be required both above and below the sink during the installation and for ongoing maintenance. + + To be delivered to the customer vertically on A-frame. We recommend transporting to the washspace on a pallet truck. FIXING 67mm 533mm 600mm 600mm 533mm 67mm 928mm 893mm 663mm FIXING LOCATIONS TSL-AEROFOIL WALL MOUNTED BASIN manual 5
before you install FIXING 92mm Minimum Void Access Required Above Washplane For Initial Installation And Ongoing Routine Maintenence. TSL-880 And TSL-470 Series (Not Included) See Seperate Data Sheet 67mm 850mm Recommended Sink Height 1-1/4" Waste 6 TSL-AEROFOIL WALL MOUNTED BASIN manual
TOP LENGTH +10mm 300mm 600mm 600mm 600mm 300mm ve Washplane And Ongoing TSL-470 Series ) e Data Sheet LENGTH FRONT e Data Sheet 67mm 533mm 600mm 600mm 533mm 67mm 1-1/4" Waste Access Required Below Washplane For Initial Installation And Ongoing Routine Maintenence. TSL-AEROFOIL WALL MOUNTED BASIN manual 7
assembly 1 Screw clamping feet (P8) into the main body (P2). 2 Slide cantilever section (P3) into main body (P2) and secure into place with M8 x12 cone point (F4). 3 Fix the M8x12 countersunk screw (F2) and M8 tee nuts (F5) through the Wall fixing plate (P9) leaving it loose. 4 Slide the assembly into the main body (P2) and tighten the fixing. As it tightens the tee nut will turn 90degrees and lock in place. Make sure that the position of the plates aligns with the marker on the main body and that it is plumb level. 8 TSL-AEROFOIL WALL MOUNTED BASIN manual
5 Apply the seal (P13) to the main body end caps (P4,P5). 6 Attach end caps (P4,P5) to the main body (P2) with M5x12 countersunk screw (F1). 7 Knock in Cantilever end cap (P6,P7) for the cantilever(p3) and apply a small amount of adhesive. 8 Slide grate into the Main body (P2) and secure with tape (F9). TSL-AEROFOIL WALL MOUNTED BASIN manual 9
assembly 9 Fit foot caps (P12) and screw in adjustable feet (P12) to the legs (P10). 10 Slide M6 tee bolts (F6) through the Leg (P10) and tighten with M6 nut (F8) and washer (F7) leaving it loose. 11 Slide the assembly into the main body (P2) and tighten the fixing. As it tightens the tee nut will turn 90degrees and lock in place. Make sure that the position of the plates aligns with the marker on the main body and that it is plumb level. 12 Place rubber gasket (P14) onto the top face of the assembly. 10 TSL-AEROFOIL WALL MOUNTED BASIN manual
how to install 928mm 36 1/2" 1 Using the adjustable feet (P12), adjust the feet so that the assembly is plumb and at the desired height (see drawing on page 5). 2 Once at the correct height, mark the fixing points on the wall. 3 Fix assembly to the wall with appropriate fixings, again making sure that the assembly is plumb level. 4 Adjust any loose feet so they are firmly on the floor. TSL-AEROFOIL WALL MOUNTED BASIN manual 11
how to install 5 Carefully slide the washplane into the slot, making sure holes line up on the underside. Then clamp in place with the clamping feet (P8). 6 Fix from underneath with M6x14 Pan head (F3) washer (F7). 7 Apply silicone seal (A1) down the side of the joining. 8 Remove tape (F9) Slide grate (P15) into position. 12 TSL-AEROFOIL WALL MOUNTED BASIN manual
9 Slide M6 tee bolts (F6) through the Lovair waste (p16) and tighten with M6 nut (F8) and washer (F7) leaving it loose. 10 Use markings on the underside of the main body (p2) to align the waste assembly. Slide the assembly into the main body (P2) and tighten the fixing. As it tightens the tee nut will turn 90degrees and lock in place. 11 Soap feeds and water can either go around the aerofoil or through the channels at the back. 12 Check that everything is watertight. TSL-AEROFOIL WALL MOUNTED BASIN manual 13
maintenance The Aerofoil should be thoroughly cleaned once every year to prevent blockages and build up of dirt. There are two ways to clean the water trough. Method 1, remove the waste (P16) to access the slot below the washplane. + + To reattach the waste, Slide M6 tee bolts (F6) through the Lovair waste (p16) and tighten with M6 nut (F8) and washer (F7) leaving it loose. + + Use markings on the underside of the main body (p2) to align the waste assembily. Slide the assembly into the main body (P2) and tighten the fixing. As it tightens the tee nut will turn 90degrees and lock in place. Method 2, slide the grate (P15) up with a flat implement like a flat headed screwdriver and wedge in place to gain access to water channel behind the sink for cleaning. The grate will slide back down once the wedge is removed. Make sure that the grate is flush with the washplane. 14 TSL-AEROFOIL WALL MOUNTED BASIN manual
cleaning Please see cleaning guide for more detailed information Solid surface Recommended cleaning Clean the surface with mild household cleaners and always use a non-abrasive cleaning sponge or pad to remove any stubborn stains. Always clean in a circular motion and you should also avoid using excessive pressure or force. If a stain sets on the surface, soak the area for a short time to loosen stubborn particles, and then use a soft cloth to lift and remove the stain. Do not use Paint stripper, brush cleaners, metal cleaners, cleaners containing methylene chloride, acid drain cleaners, acetone based nail varnish removers If any of the above are used, it should be flushed promptly with clean water to avoid damage to the surface. Keep away from UV lighting Quartz Recommended cleaning Clean the surface with mild household cleaners and always use a non-abrasive cleaning sponge or pad to remove any stubborn stains. You should also avoid using excessive pressure or force. If a stain sets on the surface, soak the area for a short time to loosen stubborn particles, and then use a soft cloth to lift and remove the stain. Trichloroethylene, acetone and paint thinners may be used to remove a specific stains. After scrubbing, wipe off the product with clean water. Do not use Bleach, alkaline cleaning products above Ph>10, chlorine-based products, Hydrofluoric acid, Dichloromethane, Sodium hydroxide - caustic soda, paint strippers, acid drain cleaners, degreasing agents. If any of the above are used, it should be flushed promptly with clean water to avoid damage to the surface. Keep away from UV lighting TSL-AEROFOIL WALL MOUNTED BASIN manual 15
cleaning Marble Recommended cleaning Clean the surface with hot water or a specially formulated marble cleaner and always use a non-abrasive cleaning sponge or pad to remove any stubborn stains. You should also avoid using excessive pressure or force. If a stain sets on the surface, soak the area for a short time to loosen stubborn particles, and then use a soft cloth to lift and remove the stain. Using a mild soapy water solution for cleaning marble won t harm the stone, but consistent use will lead to a dull film covering the surface like soap scum Do not use Bleach, Generic household cleaner, alkaline and acidic cleaning products, chlorinebased products, Hydrofluoric acid, Dichloromethane, Sodium hydroxide - caustic soda, paint strippers, degreasing agents, brush cleaners, metal cleaners, cleaners containing methylene chloride, acid drain cleaners, acetone based nail varnish removers. If any of the above are used, it should be flushed promptly with clean water to avoid damage to the surface. 16 TSL-AEROFOIL WALL MOUNTED BASIN manual
warranty We believe the future is personal. With a global mindset, we challenge conventional restroom norms via product innovation to create considered washroom solutions for corporate and educational spaces. We use rich raw materials, cutting-edge automation and considered washroom design to powerfully and positively influence the lives of people. We are The Splash Lab. Demonstrating our commitment to quality and our belief in the strength of our designs, we can offer the following warranties. The Splash Lab will warrant that its products will be free of manufacturing and material defects during normal use and environmental conditions as detailed below: 5 years parts & labour, plus an additional 4 years parts only If a defect is found in normal use, The Splash Lab. will, at their discretion, repair, provide a replacement part or product, or make appropriate adjustments. Damage caused by accident, misuse, or abuse is not covered by this warranty. Improper care and cleaning will void the warranty. Non-operation of the product due to environmental conditions beyond our control, installation error, incorrect maintenance, water quality, fair wear and tear, incorrect or inappropriate installation, misuse and abuse is not covered by the warranty. Proof of purchase (original sales receipt) must be provided to The Splash Lab with all warranty claims. The above warranty is valid for goods supplied within the United Kingdom. For goods supplied outside of the United Kingdom, The Splash Lab will honour the above stated warranty periods for the parts only. THE SPLASH LAB DISCLAIM ANY LIABILITY FOR SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES. TSL-AEROFOIL WALL MOUNTED BASIN manual 17
contact General information info@thesplashlab.com +44 (0) 161 482 7000 Technical support technical@thesplashlab.com For further contact information visit: www.thesplashlab.com 18 TSL-AEROFOIL WALL MOUNTED BASIN manual
TSL-AEROFOIL WALL MOUNTED BASIN manual 19
TSL-Aerofoil (EUR) Rev 1-26/03/18