ST76/96 series instructions - PDF Free Download

ST76/96 series instructions 1. Characteristics: 6 bit counter, timer, meter meter. 6 digit counting and timing machine. The counter relay has R, N, C, F, B preset functions. The timer relay has 4 types of output. Blackout memory function. The measurement is accurate and easy to read, and its anti-interference ability is strong. The two channels can be independent relay alarm output. Input, switch, NPN sensor with rotary encoder Input With RS485 MODBS communication interface Read and write with Bluetooth interface 2. model&meaning ST76/96-C Counter&Meter meter ST76/96 - T timer ST76/96 - CZ count meter general T76/96 - CT counting timer ST76/96 - CP counting meter batch 3. Specification

4. wiring connection proximity switch 15:brown 12:black 14:blue Encoder 15:power 12:A phase 13:B phase 14:ground 5.Relay action mode description

R N C F B The count process shows that the value reaches the set value relay output. After the delay "T" time, the relay returns, the count value is recovered at the same time, and the count is restarted. When the value of the counting process reaches the set value, the output of the relay is kept constant until the manual or external signal is reset, the relay is reset, counting value is reset, and the count is started again. The relay automatically returns after the count process shows the value of the relay output, and the value of the count is immediately reset, and the delay time is T. When the count process shows that the value reaches the set value relay output, the count value continues to rise until the manual or external signal is used. Reset, relay return, count value again zero, start counting again When the count process shows that the value of the relay is up to the set value relay output, the relay is disconnected when the set is less than the set value, and the relay is manual or External signal reset, relay reversion, count value zero ST76- T multi-function time relay Parameter setting and output action diagram A L 1 output alarm setting range (0-99 days 24 hours 59 minutes) Factory default 0 0 00 00 A L 2 output alarm setting range (0-99 days 24 hours 59 minutes) Factory default 0 0 00 00 Note: under the working state, press the " " key "and enter the AL1 alarm set directly."

Set, press " " key to select the modified bits, and the key modifies the bit.press "SET" to enter the AL2 alarm set, and then press SET to exit one Level menu modification. For example: a cumulative way down timer (C P 1 input Down, C P 2 input to accumulate, when added to the maximum value of the instrument Automatic A L 2 alarm output, input signal is useless, A L 2 output time It's one second, and the way it works is to start counting the time. Down to the Minimum instrument automatic alarm A L 1 output, input signal is useless, A L 1 output time is 1S, work for the electricity meter started down SC1=0 instrument (minutes and seconds down), SC2=0 (time division second tired Add), the initial value P R E 1 is set to 99 H 59 M 59 S, initial value P R E 2 set 00 H 00 M 00 S, A L 1 = 00 H 00 M 00 S, A L 2 = 99 H 59 M 59 S, A L 1 relay output time T I A 1 = 1 sec, A L 2 relay time T I A 2 = 1 sec, O U T 1 (A L 1) relay output amplifier = 1, O U T 2 (A L 2) relay Output type C = 1, N = 3 (A L 1 A L 2 accumulation down. ) Timer setting diagram 6 bit timer two level parameter setting (function setting)

for 3s Two level parameter entrance password, enter "000001", enter After the two level parameter menu, the instrument is out of the working state. The minimum time setting unit (0, 1, and no time every minute The default of 2, day time is 0. The minimum time setting unit (0, 1, and no time every minute The default of 2, day time is 0. Initial value 1 set <0-999999), non programming Reload the initial value by the "RST" key and open from "0". This value is defaults to 6 "0" at the beginning of the count. Initial value 2 set <0-999999), non programming Reload the initial value by the "RST" key and open from "0". This value is defaults to 6 "0" at the beginning of the count. minutes) A L 1 output alarm set range (0-99 days 24 hours and 59 Clock) when the measured value is less than this value when the AL1 output alarm output, down at The default is 00.1 0.00 Al2 output alarm set range (0-99 days 24 hours 59 minutes A L 2 output alarm when the measured value is greater than this value, the default is 00.2 0.00

defaults to 5 seconds. A L 1 alarm relay output time setting (0-9999.99 seconds) seconds. A L2 alarm output time setting (0-9999.9 9 seconds)defaults 5 and 3. ways) A L 1 alarm AL1 relay operation mode selection (1. mode2. ways and 3. mode) AL2 alarm AL2 relay working mode selection (1. mode2. mode Combinatorial selection 0: one way combined output (alarm one follow the alarm two) 1: the two routes are accumulated and lost. 2: two independent transmission down 3: two A L 1 A L 2 accumulation independent output down. (two separate output alarm one is separated from alarm two) Factory default 0 ST76-C meter meter 6 bit counting, meter, first class parameter setting (alarm value setting)

First section output forecast 1 set range (- 199999-999 999)When the display value is greater than this value, A L 1 output alarm and factory default 000010. Second segment output main alarm 2 set range (- 199999-999999) A L 2 output alarm when the display value is greater than this value. Factory default Note: under the working state, press the " the alarm. " key to enter the first section of Set, press the " " button to select the bit to be modified, and the key modifies it. Bit, press "SET" to enter the second alarm set or exit one. Level menu modification, in programming state, press the "EXT" key to exit the first level Menu settings Give an example: The device uses a rotary encoder input, with a circle of 1000 pulses. The circumference of the shaft is 0.3 meters, after a decimal point, the 2 bits are displayed, and the main alarm is made.the AL2 is 20 meters, and the delay is automatically reset by 5 seconds. "0" began the plan, the warning AL1 of 19 meters, that is, ahead of time 1 meter warning, sampling frequency is 3000 pulses per second, set up As follows: 1. The first level menu AL1 is set to 19, and AL2 is set to 20 The 2. two level menu L O C K menu input password 000001, will PRE is set to "000000", and T I M 1 is set to 5, TI M 2 is set to 5, O U T 1 is set to 0 (R mode),out2 is 0 (R mode), and the C P sampling speed is set to 3,

that is 3000 pulses per second. 3. When the instrument is used for length measurement and control, the ratio calculation method is:the number of pulses of a circumference divided by an encoder (or a meter wheel). 0.3/1000=0.00030. 4. if the measurement and display unit is rice and centimeter, then DPSET The value is adjusted to 0. If the millimeter is to be displayed, At least 3 bits of =000.000. are left after the display value decimal point 5. if it is found that the display value of the instrument does not coincide with the actual value, such as error 10 meters, showing 100 meters, the actual value of 110 meters, the calculation method is: 0.00030/X=100/110 0.00030/X=0.90909 X=0.00030/0.90909 X=0.00033,0.00033 is the latest multiplier value 6 bit counting, meter, two level parameter setting (function setting) for 3s The two level parameter entrance password, input "000001", after entering the two level parameter menu, the instrument exit the working state. Count ratio setting (0. 00001-9. 99999) out of factory default 1 The decimal point is set, according to the mobile decimal point position.set (the position of the mobile decimal point determines the measuring range of the instrument) Initial value setting (-199999-999999),The default of the factory is 6 "0"

2: two independent transmission down 3: two AL1 down AL2 cumulative independent output. (A: two separate output alarms are separated from the alarm two, B: when the amount or batch is displayed, the instrument has only one way Output, that is, CN=0.) factory default 0 Input type selection: 0. ordinary switch signal, 1. encoder input. ST76-C counter & meter 6 bit counting, meter, first class parameter setting (alarm value setting) Push First section output forecast 1 set range (- 199999-999 999)When the display value is greater than this value, A L 1 output alarm and factory default 000010. Second segment output main alarm 2 set range (- 199999-999999) A L 2 output alarm when the display value is greater than this value. Factory default Note: under the working state, press the " " key to enter the first section of the alarm. Set, press the " " button to select the bit to be modified, and the key modifies it. Bit, press "SET" to enter the second alarm set or exit one.level menu modification, in programming state, press the "EXT" key to exit the first level Menu settings Fox example: The device uses a rotary encoder input, with a circle of 1000 pulses.the circumference of the shaft is 0.84 meters, after a decimal point, the 2 bits are

displayed, and the main alarm is made. The AL2 is 20 meters, and the delay is automatically reset by 5 seconds."0" began the plan, the warning AL1 of 19 meters, that is, ahead of time1 meter warning, sampling frequency is 3000 pulses per second, set up As follows: 1. The first level menu AL1 is set to 19, and AL2 is set to 20 2. The 2, two level menu L O C K menu input password 000001, will PRE is set to "000000", and T I M 1 is set to 5,TI M 2 is set to 5, O U T 1 is set to 0 (R mode),out2 is 0 (R mode), and the C P sampling speed is set to 3, that is 3000 pulses per second. 3. When the instrument is used for length measurement and control, the ratio calculation method is:the number of pulses of a circumference divided by an encoder (or a meter wheel). 0.84/1000=0.00084. 4. if the value of the measurement is only to be displayed in centimeters, then DPSET The value is adjusted to 0. 5. if it is found that the display value of the instrument does not coincide with the actual value, such as error 10 meters, showing 100 meters, the actual value of 110 meters, the calculation method is: 0.00084/X=100/110 0.00084/X=0.90909 X=0.00084/0.90909 X=0.000924,0.000924 is the latest multiplier value. for 3s The two level parameter entrance password, input "000001", after entering the two level parameter menu, the instrument exit the working state. Count ratio setting (0. 00001-9. 99999) out of factory default 1 Set the decimal point, press the position of the moving decimal point. (the position of the moving decimal point determines the measuring range of the instrument)

Initial value setting (-199999-999999) and factory default of 6 "0" The first 1-10 groups select the output forecast police, A L 1 S E T setting range (1-9) When the display value is equal to the output of the 01 instrument A L 1 S E T, when the display value is displayed Equal to 02 instruments A L 1 S E T two sets output, when the instrument display value The 05 instrument A L 1 S E T is the output of 5 sets, and the factory default 01. Alarm 1 output time set (0000.00-9999.99 seconds) out of factory default 5 Second stage output main alarm 2 set range (- 199999-9999 99) A L 2 output alarm when the display value is greater than this value. Factory default Alarm 2 output time set (0000.00-9999.99 seconds) out of factory default 5 Alarm 1 output mode selection ((0. R mode 1. N mode 2.)C mode 3.F mode 4. B mode) factory default 0. Alarm 2 output mode selection (0. R mode 1. N mode2. C mode 3.F mode 4. B mode) factory default 0 Select the factory default 0 for counting frequency "0" is 5PCS /S, "1", "20PCS/S," "3" for 3000PCS/S "4" is greater than 3000PCS/S)

"2" 200PCS/S Combinatorial selection 0: one way combined output (alarm one follow the alarm two) 1: the two routes are accumulated and lost. 2: two independent transmission down 3: two AL1 down AL2 cumulative independent output. (A: two separate output alarms are separated from the alarm two, B: when the amount or batch is displayed, the instrument has only one way Output, that is, CN=0.) factory default 0 Input type selection: 0. ordinary switch signal, 1. encoder input. ST76- CT counter timer 6 bit counting and one level parameter setting (alarm value setting) Push A L 1 output alarm (count output) setting range (0-999999) when the measured value is greater than this value, A L 1 output alarm.recognize 000020 A L 2 output alarm (time output) set range (0-99 hours 59 minutes and 59 seconds) when the measured value is greater than this value, A L 2 output alarm output Factory default 0.2 0 Note: press the " " key "" under the work state and enter the AL1 alarm set directly.

Click the button to select the bit to be modified, and the key changes the bit. "SET" enters the AL2 alarm value setting, and then press SET to exit the first level Menu modification For example: counting timer setting (short circuit of CP1 and COM to count signal input port, CP2 and COM short circuit as timing signal input port) The counter SC1=0 count, SC2=0 cumulative time, initial PRE1=0, initial PRE2=0.AL1 count alarm timer value is set to 5000 AL2 alarm value is set to 00 hours and 0.59 minutes.al1 count alarm time TIA1 is set to 1, AL2 times the alarm time setting TIAL 1, AL1 count output mode OUT1=0, AL2 timing output OUT2=1. When the input signal on the display meter, the cumulative value, lower cumulative display timing value. Count the cumulative time down set map for 3s Two level parameter entrance password, input "0000001", after entering the two level parameter menu, the instrument is out of work state Count: 0. count 1. count down, the default 0. fastest 20 times per second. Time: 0. cumulative time, 1. down time, default 0.

The count initial value is set by <0-999999), and the default is 6 "0". The initial value of the timing is set < 0-99 hours, 59 minutes and 59 seconds), and the default is 6 "0" The count output alarm value is set 0-999999, the default 50. The timing alarm value is set for 0-99 hours, 59 minutes and 59 seconds, and the default is 59 seconds. The output time of the count A L 1 relay is set:(0-9999.99 seconds) Timing A L 2 relay output time setting:(0-9999.99 seconds) Count output mode selection ((0. R mode 1. N mode 2. C mode 3. F mode 4. B mode) Timing output selection (1. mode 2. mode 3. mode 4. mode (when O U T 2 = 4, instrument can display A L 3 and T C L R menu.) The counting signal interval time is set, 0-999999 seconds, the default 5 seconds. A L 2 relay output auto reset T C L R setting 0, A L 2 follow Electrical output manual reset T C L R setting 1, factory default 0.

ST76- CP batch meter meter 6 bit counting, meter, first class parameter setting (alarm value setting) Push First section output forecast 1 set range (- 199999-999 999) A L 1 output alarm when the display value is greater than this value, and there is no this item at the default 000010 single section of the factory. Second stage output main alarm 2 set range (- 199999-9999 99) A L 2 output alarm when the display value is greater than this value. Factory default Note: work under strong state according to the " " key, directly into the first alarm setting, press " " button to select the modified, modify the button, press the "S E T" to enter the second stage set the alarm value or exit the menu changes, programmed under press "E X T" key to exit a single set of dishes For example: The equipment uses rotary encoder input, a circle of 1000 pulse axis is 0.84 meters in circumference and 2 decimal display, alarm AL2 is 20 meters, delay 5 seconds automatic reset, reset after the start counting from the "0" alarm, AL1 is 19 meters, which is 1 meters in advance warning, sampling the frequency of 3000 pulses per second, parameter settings are as follows: 1. The first level menu AL1 is set to 19, and AL2 is set to 20 2. level two menu, LOCK menu, enter the password 000001, set PRE to "000000", TI M 1 set 5, TIM2 set 5, OUT1 set to 0 (R way), OUT2 is 0 (R mode), CP sampling speed is set to 3, 3000 pulse /sec 3. When the instrument is used for length measurement and control, the ratio of the ratio is calculated: the number of the perimeter divided by the encoder (or the meter wheel). That is, 0.84/1000=0.00084. 4. If the measurement display value is only centimetre, then DPSET The value

is adjusted to 0. 5. If the display value of the instrument does not coincide with the actual value, if the error is 10 meters, the display is 100 meters and the actual value is 110 meters. The calculation method is: 0.00084/X=100/110 0.00084/X=0.90909 X=0.00084/0.90909 X=0.000924,0.000924 is the latest multiplier for 3s The two level parameter entrance password, input "000001", after entering the two level parameter menu, the instrument exit the working state. Count rate setting (0.00001-9.99999) out of factory default 1 Set the decimal point, press the position of the decimal point. (the position of the mobile decimal point determines the measuring range of the instrument) The initial value is set (- 199999-999 999), and the factory default is 6 "0" Alarm 1 output time set (0-9999.99 seconds) out of factory default 5 Alarm 1 output time set (0-9999.99 seconds) out of factory default 5 Alarm 1 output mode selection ((0. R mode 1. N mode 2.C mode 3.F mode 4. B mode) factory default 0.

Alarm 2 output mode selection ((0. R mode 1. N mode 2.C mode 3.F mode 4. B mode) factory default 0. Counting frequency select factory default 0 "0" is 5PCS /S, "1" 20PCS/S, "2" 200PCS/S "3" is 3000PCS/S "4" more than 3000PCS/S). Input type selection: 0. ordinary switch signal, 1. encoder input. Batch cleaning: 0. button can not be zero, the 1. button can be zero. Note: the batch can not be changed in the working condition. It can only be changed in the downtime or into the two level menu. ST76- CZ meter meter for total amount counting 6 bit counting, meter, first class parameter setting (alarm value setting) Push First section output forecast 1 set range (- 199999-9999 99) A L 1 output alarm when the display value is greater than this value, and there is no this item at the default 000010 single section of the factory Second stage output main alarm 2 set range (- 199999-9999 99) A L 2 output alarm when the display value is greater than this value. Factory default 000020

Note: work under strong state according to the " " key, directly into the first alarm setting, press " " button to select the modified, modify the button, press the "S E T" to enter the second stage set the alarm value or exit the menu changes, programmed under press "E X T" key to exit a single set of dishes For example The equipment uses rotary encoder input, a circle of 1000 pulse shaft circumference of 0.84 meters, after the decimal point display 2, A L 2 as the main alarm 20 meters, delay 5 seconds automatic reset, reset after the start counting from the "0", warning A L 1 is 19 meters, which is 1 meters ahead pre alarm, the sampling frequency is 3000 pulses per second, parameter setting As follows: 1, the first level menu a L 1 is set to 00 to 9. 00, 2002 is set to 0 A L. 00 2, 2, level two menu, LOCK menu, enter the password 000001, set PRE as "000000", T I M 1 set 5, T I M 2 set to 5, O U T 1 set 0 "(R mode),o U T 2 set 0 "(R mode),the sampling speed of C P is set to 3, that is, 3000 pulses per second. 3, when the instrument is used for length measurement and control, the rate calculation is divided into the number of pulses of encoder or meter, that is, 0.84 / 1000 = 0.00084. 4. if the measurement display value only needs to display a centimeter, then the value of D P S E T is adjusted to 0. 5. if it is found that the display value of the instrument does not coincide with the actual value, such as error 10 meters, showing 100 meters, the actual value of 110 meters, the calculation method is: 0.00084 / X = 100 / 110 0.00084 / X = 0.90909 X = 0.00084 / 0.90909 X = 0.000924, 0.000924 is the latest multiplier for 3s The two level parameter entrance password, input "000001", after entering the two level parameter menu, the instrument exit the working state

Count rate setting (0.00001-9.99999) out of factory default 1 Set the decimal point, press the position of the decimal point. (the position of the mobile decimal point determines the measuring range of the instrument) Initial value setting (-199999-999999) and factory default of 6 "0" Alarm 1 output time set (0-9999.99 seconds) out of factory default 5 Alarm 1 output time set (0-9999.99 seconds) out of factory default 5 Alarm 1 output mode selection ((0. R mode 1. N mode 2.C mode 3.F mode 4. B mode) factory default 0. Alarm 2 output mode selection ((0. R mode 1. N mode 2.C mode 3.F mode 4. B mode) factory default 0. Counting frequency select factory default 0 "0" is 5PCS /S, "1" 20PCS/S, "2" 200PCS/S "3" is 3000PCS/S "4" more than 3000PCS/S). Input type selection: 0. ordinary switch signal, 1. encoder input.

Batch cleaning: 0. button can not be zero, the 1. button can be zero. Note: the batch can not be changed in the working condition. It can only be changed in the downtime or into the two level menu. 1 Instruments work or exceed set value relays 2 The meter have power but not work use reset key to restart 3 Check the signal input Note: the electric instrument stay 1 second upper display SANTEN, lower display factory time such as 160425 mean 16 years 04 months in No. 25 factory. Press the SET key to enter the program, the key selected to set the bit, by changing the value of the bit. Then press the SET key to confirm the setting parameters and jump to the bottom A parameter setting state and exit programming state according to EXT! Press and hold SET and EXT key after 5 seconds to enter COD=000000 (set the instrument is counter, timer, timing counting machine, batch, total)the COD value changed to 000001, press SET to confirm after SET. The default display instrument on the 000000, when SET=0.Meter meter general. 1. timer, 2 counting timing machine, 3. batches of counter. 4. total amount counter. Press SET button to confirm the top of the instrument TIME (delivery time). The default display 0 by SET in addition, if it is a two way counting timer, the first one on the right is AL1 zero button ( ), and the second on the right is AL2 zero button