TECHNICAL DATA SHEET WORKING SPECIFICATION Mains Power Supply: Wall Mounting Operating Voltage Online Connectivity Maximum Load Data Feedback 100-240V AC / 50-60Hz 12V DC Snap fit, quick release wall bracket included WiFi, LoRaWAN, GSM 300mA @ 12VDC Average consumption, Predicted replenishment, Live consumable level feedback, Remote access to settings, Peak time analysis, Activation count, Email alerts, Toilet paper monitoring Working Temperature Online Security Protocols 600mA @ 12VDC Working Load 5-55 C Weight 0.7Kg Local access + key combination required to launch portal, SSL encryption, SHA256 hash encryption Warranty Contract Dependant (2 year - unlimited) Sensor Float Switch or Flow Switch enabled for cisterns and solenoid operated urinals 35mm 120mm Approvals CE Dose Size 0.5-10ml per activation Pump to cistern - 3m Max, Pump to reservoir - 8m Max 140mm Installation Distances
INSTALLATION REQUIREMENTS & IMPORTANT INFORMATION Blue Reservoir Position Please see the below diagram that shows appropriate mounting positions. Set up of Blue Dispenser The Blue Dispenser is delivered ready to use, if you wish to change any of the settings you can do so via the UI on the dispenser. Recommended Blue To be used with Rapid Washrooms Blue only. Warranty void if other Blue is used. Power Recommended to be hard-wired to spur by qualified professional. Blue Dispenser should be mounted no further than 500mm away from the cistern. Dosing Nozzle should be mounted so that it is above the water level of the cistern when full. Float Switch should be mounted so that there is enough space for the float switch to open fully and close with no obstructions. The water level should rise above it when the cistern is full and drop completely below the switch when empty. Reservoirs should be placed no more than 5m away from the Blue Dispenser. Total length of Power Lead is 3.5m. Power point must be reachable.
CISTERN REQUIREMENTS & IMPORTANT INFORMATION Cistern wall thickness must be between 1mm - 5mm 16mm hole required for mounting the Blue Dosing Nozzle. 22mm hole required for mounting the Float Switch.
INSTALLATION SCENARIOS Cistern positioned in a void behind the toilet with a 5L reservoir. This installation is suitable for cisterns that are mounted in a cavity that is separate to the toilet, where there is no public access. A 5L bottle reservoir can be used to feed a maximum of one system. If you require a reservoir to feed more than one system please see the installation for a 32L centralised reservoir. Toilet Cistern Wall 5L Reservoir
INSTALLATION SCENARIOS Cistern positioned in a void behind the toilet with a 32L reservoir. This installation is suitable for cisterns that are mounted in a cavity that is separated from the toilet, where there is no public access. A 32L reservoir can be used to feed one system. The reservoir tank has a screw in lid with a latch and padlock to prevent tampering. If you require a reservoir to feed more than one system please see the installation for a 32L centralised reservoir on the next page. Toilet Cistern Wall 32L Reservoir
INSTALLATION SCENARIOS Multiple cisterns positioned in a void behind the toilet with a 32L reservoir. This installation is suitable for multiple cisterns that are mounted in the same cavity separate to the toilets, where there is no public access. The distance between furthest blue dispenser to the reservoir must not exceed 5m. A 32L centralised reservoir can be used to feed a minimum of one system and maximum of 5 systems. The reservoir tank has a screw in lid with a latch and padlock to prevent tampering. The distance between furthest blue dispenser to the reservoir must not exceed 5m. Toilet Cistern 32L Reservoir
URINAL INSTALLATION REQUIREMENTS & IMPORTANT INFORMATION Single urinals connected to either a 32L or 5L reservoir. A 32L or 5L reservoir can be used with urinal installation. The Blue Dosing Assembly (see below) is supplied with push-fit connectors that fit 12mm diameter tube. A 32L reservoir can be used to feed one system as shown below. The reservoir tank has a screw in lid with a latch and padlock to prevent tampering. If you require a reservoir to feed more than one system please see the installation for a 32L centralised reservoir on the next page. Blue Dosing Assembly Urinal sensor (not supplied) Urinal (not supplied). Blue Dispenser should be mounted no further than 500mm away from the cistern. Reservoirs should be placed no more than 5m away from the Blue Dispenser. 12mm tube (not supplied). Flush controlling solenoid (not supplied) Water inlet plumbing (not supplied). 32L Reservoir / 5L Bottle Reservoir can be used to feed a single urinal. Total length of Power Lead is 3.5m. Power point must be reachable.
TECHNICAL DATA SHEET URINAL INSTALLATION REQUIREMENTS & IMPORTANT INFORMATION Multiple urinals connected to either a 32L reservoir. A maximum of 5 urinals can be fitted to a 32L reservoir. The Blue Dosing Assembly (see below) is supplied with push-fit connectors that fit 12mm diameter tube. The Blue Dispenser situated furthest from the reservoir must not exceed a distance of 5 metres from the reservoir. It is maximum product life it is best to position the reservoir centrally between all urinals. The distance between furthest blue dispenser to the reservoir must not exceed 5m. Urinal 32L Reservoir Water Inlet