MADE TO PROTECT OUTDOOR DUAL-TECH CURTAIN DETECTORS /
EASY INSTALLATION AND CONFIGURATION COMPACT ENCLOSURE FOR INDOOR AND OUTDOOR USE RELIABLE DETECTION Detector applications in residential, business and industrial buildings: Common features: can be used both indoors and outdoors protection of building along its outer wall high resistance to adverse weather conditions protection along the property fence protection of entrance gate or garage door IP54 rating compact dimensions outdoor and indoor protection of balcony / terrace / ordinary windows reliable operation detection of entry into protected zone tamper protection protection allowing for passage of pets user-selectable mounting EXTRA FEATURES can be used as part of the ABAX wireless system detection circuit sensitivity configured remotely from DLOADX program battery level checking EXTRA FEATURES active IR anti-masking Grade 3 security for indoor applications stepless configuration of detection circuit sensitivity
The alarm system is designed to protect the entire premises i.e. the building interior and the surrounding area. Security at the boundary between these two areas and along the fence of the plot is provided by curtain detectors, which belong to the group of perimeter protection devices. The compact and slim enclosures of the and curtain detectors contain advanced technological solutions which enable a virtual wall to be created both outside of the protected buildings as well as in their interiors. The first of them is a wired device, so it can be part of any security alarm system. The other one is a wireless detector, designed to work as part of the ABAX two-way wireless system. ta mp er s witch r so en 24 G s Hz microwave PI R se nso r Enclosures of the detectors are made of a combination of polycarbonate and thermoplastic elastomer using two-component injection technology. The thus obtained design is IP54 rated, which makes the detectors suitable for outdoor applications as well. The enclosure also contains elements which increase resistance of the device to mechanical impact. They include e.g. a special recess for the lens to protect it from being forced in, either accidentally or intentionally. Dual tamper protection against opening the enclosure and prying the device away from the wall is also applied. The protection is implemented using a contact on the electronics board and a tamper element on the back panel of the detector enclosure. *The illustration shows detector design iv act ei Ra nti-masking l tro ma n o c nual sensitivity
range - top view 1 m 1 2,4 m range - side view The detectors have a detection angle of 10 and an operating range of 14 m. At that distance, the emitted beam has a width of approx. 1 m. 14 14 and and are provided with two detection circuits, infrared and microwave, whose sensitivity can be independently and smoothly controlled. Thus, they can be adjusted both to the function performed by the device, as well as to the characteristics of the protected premises and its users needs. Resistance to adverse weather conditions and temperature changes The dual technology of detection combined with the detector algorithm of auto-tuning to environmental conditions provides high immunity of these devices to false alarms. Therefore, they offer stable operation in harsh weather conditions, such as rain, snow, fog, intense insolation and strong gusts of air. Additionally, the devices feature high mechanical strength and resistance to UV radiation, hence their appearance remains unchanged for many years. The curtain detectors offer correct operation in a wide temperature range from -40 C to +55 C. Ambient temperature changes are automatically compensated. sensitivity temperature ( C) temperature compensation time Easy installation For standard applications, we recommend installing the detector at a height of 2.4 m, with the lens facing down. This height may be different, however, if the device is to be used e.g. for protection of a window or gate. The detector can be installed either directly on a flat surface or using a dedicated bracket that allows installation of the device at a constant angle of 90. The second option is especially useful when securing a portion of the building wall with many windows. When installing the detector inside the building, you can also use other brackets offered by SATEL. The detector can also be used to detect an entry into the protected zone which is not secured in any other way (e.g. separated by a wall, closed doors, etc.). Alternatively, the device can be installed low and, additionally, turned. Such a solution will provide protection and, at the same time, create a gap to allow, for example, a small dog to freely move around.
ADVANCED INDOOR PROTECTION Design of the detector meets the EN 50131-2-4 standard requirements for Grade 3. Therefore, the device can be used to secure the premises particularly vulnerable to burglary, which require a high degree of protection, including the jewelry shops and interiors of public buildings. With the active IR anti-masking function, all attempts to tamper with the device will be detected immediately, appropriate information being passed to the control panel. Depending on the system configuration, notification of the situation may be sent to the user, installer, security agency or a relevant department, e.g. police. According to EN 50131-2-4, active anti-masking function is implemented in the detector infrared circuit, which provides advanced protection against, for example: covering with fixed obstacles, including those that poorly reflect light like black and matt, covering with sticky transparent material, e.g. a film or adhesive tape, painting over with masking material, like paint or clear varnish, using retroreflective technology. Reflector OK = no masking! Reflector disturbed = paint-over alert TRANSMITTER RECEIVER TRANSMITTER RECEIVER IR rays varnish, paint The detector lens is secured by a retro reflector of transparent polycarbonate. Any attempt to cover it with masking material will change the refraction angle of IR rays, which will be immediately detected and signaled by the detector. WIRELESS CURTAIN PROTECTION is a curtain detector designed to work as part of the ABAX two-way wireless system. It is supported by the ACU-120 and ACU-270 controllers, ARU-100 radio signal repeater and INTEGRA 128-WRL control panel. Owing to its efficient energy management, the detector can work up to 3 years without having to replace the battery. Importantly, the battery status is continuously monitored and, on detecting low voltage, the detector will sent appropriate information to the control panel.
Summary of features and characteristics Two detection circuits: PIR+MW + + Active IR anti-masking implemented in indoor applications + Splash-proof enclosure, IP54 rated + + Tamper protection (against opening and removal) + + Reinforced polycarbonate enclosure + + Digital temperature compensation for correct detector operation in temperature range from -40 C to +55 C + + Tri-color LED + + Working as part of ABAX wireless system + Can work in adverse weather conditions (rain, snow, fog, strong wind) + + Auto-tuning algorithm for high immunity to false alarms + + Configuration of detection circuit sensitivity by using PCB potentiometers + Remote configuration of detection circuit sensitivity from DLOADX program + Optional increasing of the beams density by mounting the AOCD-CL cover with the Fresnel lens + + Low current consumption + + Dedicated angle-type bracket (90 ) + + Optional installation without any additional bracket + + * The illustration shows detector design Technical parameters Environmental class III A III A Security rating for indoor applications acc. to Grade 3 acc. to Grade 2 Enclosure dimensions 44 x 105 x 40 mm 44 x 105 x 40 mm Operating temperature range from -40 o C to +55 o C from -40 o C to +55 o C Recommended installation height 2,4 m 2,4 m Standby current consumption 21 ma 35 µa Maximum current consumption 25 ma 20 ma Operating range 14 m 14 m Wireless operation frequency band 868,0 MHz 868,6 MHz Battery / battery life CR123A 3 V / up to 3 years Radio communication range up to 500 m Detectable motion speed 0,3 3 m/s 0,3 3 m/s
MADE TO PROTECT ul. Budowlanych 66, 80-298 Gdansk, Poland tel. +48 58 320 94 00; fax + 48 58 320 94 01 e-mail: trade@satel.pl The manufacturer reserves the right to change the specification and technical data of devices. Images shown are for general information only and may differ from actual products. (IND_0318) MORE THAN 25 YEARS OF EXPERIENCE Professional protection of each type of premises, as well as people staying therein, through advanced, yet functional and cost-effective solutions these few words may serve as the shortest description of the mission of SATEL, a manufacturer of security systems with involvement of 100% Polish capital. Due to integrity in business and a special emphasis on high quality and a wide range of products offered, the SATEL brand has been highly appreciated in the industry for over 25 years. This philosophy of management and hard work of more than 300 SATEL s employees produce tangible results. The wide range of over 400 offered products provides countless opportunities to create security, home automation, fire alarm, access control and monitoring systems, tailored to the individual needs of each user. At the same time, these systems meet all requirements prescribed by Polish and international regulations and industry standards. Bringing the functionality of devices into line with current requirements and expectations of the market with the use of the latest technologies is one of the main objectives of SATEL. For this reason the design and production departments of the Company are continuously being modernized and expanded. A natural consequence of all actions aimed at the production of top-quality devices was the introduction of the quality management system conforming to ISO 9001:2000 in 2002. Regardless of this certification, SATEL also carries out a full functional test of all products leaving the production line, thus ensuring reliability of the manufactured devices. Focusing on modern design and attaching importance to the highest levels of quality and functionality of its products, SATEL has gained many satisfied customers not only in Poland but also in more than 50 markets worldwide.