model with1920fr ADA Compliant Freeze-Resistant Wall-Mount Fountain and Bottle Filler FEATURES & BENEFITS CONSTRUCTION Unit is made of 18-gauge Type 304 stainless steel with a satin finish that resists stains and corrosion, and has soft, rounded corners. Unit features stainless steel satin-finish back panel, vandal-resistant bottom plate, and 1-1/4 integral trap. FREEZE-RESISTANT VALVE Fully-engineered system with the pneumatic-operated, freeze-resistant valve mounted in a cabinet that is installed on the inside wall where room temperature does not drop below 50 F (10 C). When valve goes to off position, water left in supply line between valve and bubbler drains back into waste inside cabinet, protecting the unit from freezing, and allowing fountain to function year-round. BOTTLE FILLER (FR) Vandal-resistant, 14-gauge Type 304 stainless steel bottle filler housing with pneumatic push button operation. BARRIER-FREE Barrier-free capabilities combined with its ease of use allows for a number of installation location possibilities. BUBBLER HEAD Polished chrome-plated brass bubbler head with integral basin shank for added strength. Shielded, angled stream opening provides a steady, sanitary source of drinking water at.45 gpm. BACK PANEL Stainless steel back panel helps to protect the wall from inadvertent splashing, and its decorative satin finish increases location visibility and completes the fountains attractive appearance. OPTIONS Fountain Skirt: Model SK1, satin finish stainless steel cane touch skirt for installation on high unit in some applications that may need to comply with ADA protruding objects guidelines. Mounting Plate: Model 6700.4, Hi-Lo universal mounting plate for most dual bubbler fountains. Mounting Plate: Model 6700.4L, in-wall mounting plate for model 1920 over low side of dual drinking fountains. Mounting Plate: Model 6700R, on-wall mounting plate for 1920 series bottle fillers, single or dual fountain retrofit installations. Custom Logo Panel: Standard Model 6475 comes with Hydration By Haws logo. Customize the panel with your choice of logo, slogan, or graphic. For customization, call 888-640-4297. MODEL CHOICE / BP32 / 1920FR / 6521FR (qty 3) / 6469 Model, freeze-resistant fountain with stainless steel back panel, freeze-resistant stainless steel bottle filler, three freeze-resistant valve systems, and drip tray. / BP32R / 1920FR / 6521FR (qty 3) / 6469 Model, freeze-resistant dual fountain with reverse-mount stainless steel back panel, freezeresistant stainless steel bottle filler, three freeze-resistant valve systems, and drip tray. When ordering, ask for model and note it to be reversed. SPECIFICATIONS Model with 1920FR bottle filler: ADA compliant Hi-Lo wall-mounted freeze-resistant drinking fountain with push button operation. Fountain shall include dual 18-gauge Type 304 stainless steel satin-finish basins, polished chrome-plated brass vandal-resistant bubbler heads, polished chrome-plated brass vandal-resistant waste strainers, stainless steel satin-finish back panel, high and low fountain mounting levels, and 1-1/4 waste trap. Fountain and bottle filler use polished chromeplated brass push-buttons which operate pneumatic valves, housed in insulated cabinets, installed on the inside wall where room temperatures do not drop below 50 F (10 C), with self-draining water lines that protect the unit from freezing, and vandal-resistant bottom plates. CSA certified and ADA accessible, NSF/ANSI Standard 61, Section 9, lead free. 1455 Kleppe Lane :: Sparks, NV 89431 :: p. 775.359.4712 :: f. 775.359.7424 :: e. info@hawsco.com :: www.hawsco.com
- - THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS 6700.4L MOUNTING PLATE (BEHIND FINISH WALL) - OR - 6700R RETROFIT PLATE (ON TOP OF FINISH WALL) 1920FR 3/8" OD POLYPROPYLENE 7/8" OD INSULATING TUBING (MUST COVER TUBING (CONNECT TO NOZZLE ENTIRE SUPPLY TUBING, FROM THE WITH SUPPLIED PUSH IN ELBOW, NOZZLE TO MODEL 6521FR ASSEMBLY, TRIM TO FIT. TRIM TO FIT. CONNECT AIR LINE TO BOTTLE FILLER PUSH BUTTTON, TRIM TO FIT. 1/2" NPT SUPPLY 1-1/4" NPT WASTE (NOT SUPPLIED) BP32 6469 INSTALLATION ABOVE HAWS NOTES: 1 THIS BOTTLE FILLER REQUIRES THE USE OF MODEL 6521FR FREEZE RESISTANT VALVE ASSEMBLY (SOLD SEPERATELY) 2 VALVE ASSEMBLY MUST BE INSTALLED IN A WARM AREA. PROVISIONS SHOULD BE MADE TO ALLOW ACCESS TO THE ACCESS PANEL. 3. SEE SEPERATE INSTALLATION DRAWINGS FOR FOUNTAINS, MOUNTING PLATES, BACKPANELS, AND DRIP TRAY. HOLD ROUGH-IN DIMENSIONS± 1/8" (3.2mm) 4. WHEN INSTALLING THIS UNIT, LOCAL, STATE OR FEDERAL CODES SHOULD BE ADHERED TO. FOR INSTALLATION HEIGHTS OTHER THAN SHOWN, DIMENSIONS MARKED (*) MUST BE ADJUSTED ACCORDINGLY. C (775) 359-4712 FAX (775) 359-7424 ECN NO. REVISED PER BY: PART NUMBER ECN: GC -20 DRAWN: DATE: CHK'D.: MODEL REVISION GC 07/13/17 APPROVED: DATE: WITH MODEL 1920FR BOTTLE FILLER 0A.1 SCALE: N/A DRAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 2 R 2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS 1920 MOUNTING HOLE LOCATIONS NOTES: 1 THIS BOTTLE FILLER REQUIRES THE USE OF MODEL 6521FR FREEZE RESISTANT VALVE ASSEMBLY (SOLD SEPERATELY) 2 VALVE ASSEMBLY MUST BE INSTALLED IN A WARM AREA. PROVISIONS SHOULD BE MADE TO ALLOW ACCESS TO THE ACCESS PANEL. 3. WHEN INSTALLING THIS UNIT, LOCAL, STATE OR FEDERAL CODES SHOULD BE ADHERED TO. FOR INSTALLATION HEIGHTS OTHER THAN SHOWN, DIMENSIONS MARKED (*) MUST BE ADJUSTED ACCORDINGLY. C (775) 359-4712 FAX (775) 359-7424 ECN NO. REVISED PER BY: PART NUMBER 5081 ECN: 5172 MJ DRAWN: DATE: CHK'D.: MODEL 1920FR REVISION DS 05/25/16 FV APPROVED: DATE: 3 FV 02/27/17 SCALE: N/A DRAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 3 R 2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. 0510000491.D
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS 1 6469 BOTTLE FILLER DRIP TRAY INSTALLATION 3 2 ECN NO. REVISED PER BY: PART NUMBER 5150 ECN: 5150 MJ DRAWN: DATE: CHK'D.: DRAWING, 6469 BOTTLE FILLER DRIP TRAY REVISION MJ 01/10/17 DS APPROVED: DATE: 1 FV 01/16/17 SCALE: 1:4 DRAWING TYPE: INSTALLATION SIZE: A SHEET 1 OF 1 2017 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. C R (775) 359-4712 FAX (775) 359-7424 0510000657.D
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS UNIT MAY BE RECESSED MOUNTED IN WALL AS SHOWN IN VIEW "C" OR SURFACE MOUNTED AS SHOWN IN VIEWS "A" AND "B". * FOR ALL MODELS OTHER THAN 1001FR THESE DIMENSIONS ARE 3" [76mm] SUPPLY & 3" [76mm] ACTUATION. FOR MODELS 1001FR THESE DIMENSIONS ARE 1-3/4" [44mm] SUPPLY AND 2" [51mm] ACTUATION. 1-1/4" IPS NIPPLE 1-1/4 IPS X 1-1/4 O.D. ELBOW TO DRAIN WASTE ASSEMBLY 12" [305mm] MAX WALL THICKNESS * * FOR ALL MODELS OTHER THAN 1001FR THIS DIMENSION IS 2" [51mm] FOR 1001FR THIS DIMENSION IS 1-3/16" [30mm]. 14" 356mm VALVE MUST BE INSTALLED IN SPACE THAT MAINTAINS A MINIMUM OF 50 F. 12" 305mm * *" * *mm 4" 101mm 1/8" 3mm SUPPLY COMPRESSION NUT, HANDTIGHT ONLY AIR BLEED OUTLET PORT SHUT-OFF VALVE *mm *" *mm *" SUPPLY ACTUATION WASTE 1/4" Ø MTG HOLES 6.4mm ACTUATION (AIR INLET) DRAIN VALVE 1" 25mm AIR GAP DRAIN WASTE ASSEMBLY 1-1/4 0.D. WASTE WITH 1-1/4 SLIP JOINT NUT AND WASHER FROM DRINKING FOUNTAIN SUPPLY TUBING MUST NOT HAVE DIPS OR LOW SPOTS WHICH CAN COLLECT WATER AND FREEZE 1" PIPE SLEEVE INSERT BUSHING SUPPLIED INTO APPROPRIATE 3/8" DIA HOLE IN CABINET (DEPENDING ON MODEL) FROM BEHIND. 1/8" O.D. ACTIVATION TUBING FROM PUSH BUTTON TO VALVE 1/8" PIPE SLEEVE BEND TUBING 90 4" 102mm FOAM IN- SULATION COVER 5" 127mm 3" 76mm SUPPLY 1/2" IPS SUPPLY 8" 203mm 10" 254mm 1-1/4" IPS WASTE (NOT SUPPLIED) ECN NO. REVISED PER PART NUMBER DRAWING TYPE: SIZE: A BY: DRAWN: CJL APPROVED: ECN: 4921 FV 0002077820.D DATE: CHK'D.: 6521FR FREEZE VALVE DRAWING NO. 09/92 REV DATE: 1 BUBBLER 09306A00 17 FV 10/21/14 SCALE: 1:5 INSTALLATION SHEET 1 OF 1 2014 Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation. C R (775) 359-4712 FAX (755) 359-7424