EESTI STANDARD EVS-EN ISO 1254-5:2000 Klaas ehitusmaterjalina. Lamineeritud klaas ja kildumatu lamineeritud klaas. Osa 5: Mõõtmed ja serva töötlus Glass in building - Laminated glass and laminated safety glass - Part 5: Dimensions and edge finishing EESTI STANDARDIKESKUS
EESTI STANDARDI EESSÕNA NATIONAL FOREWORD Käesolev Eesti standard EVS-EN ISO 1254-5:2000 sisaldab Euroopa standardi EN ISO 1254-5:1998 ingliskeelset teksti. Käesolev dokument on jõustatud 11.01.2000 ja selle kohta on avaldatud teade Eesti standardiorganisatsiooni ametlikus väljaandes. Standard on kättesaadav Eesti standardiorganisatsioonist. This Estonian standard EVS-EN ISO 1254-5:2000 consists of the English text of the European standard EN ISO 1254-5:1998. This document is endorsed on 11.01.2000 with the notification being published in the official publication of the Estonian national standardisation organisation. The standard is available from Estonian standardisation organisation. Käsitlusala: See standard määrab kindlaks mõõtmed, piirhälbed ja servatöötlused ehitusmaterjalina kasutatava lamineeritud klaasi ja kildumatu lamineeritud klaasi jaoks. Standardit ei saa rakendada alla 0,05 m2 klaasplaatide puhul. Scope: ICS 81.040.20 Võtmesõnad: hooned, kildumatu klaas, klaasing, lamineeritud klaas, mõõtmed, mõõtmete kontrollimine, mõõtmetolerantsid, valmistamine Standardite reprodutseerimis- ja levitamisõigus kuulub Eesti Standardikeskusele
EN ISO 1254-5 ICS 81.040.20 Descriptors: Building, laminated glass, safety glass, edge finishing, testing. June 1998 English version Glass in building Laminated glass and laminated safety glass Part 5: Dimensions and edge finishing (ISO 1254-5 : 1998) Verre dans la construction Verre feuilleté et verre feuilleté de sécurité Partie 5: Dimensions et façonnage des bords (ISO 1254-5 : 1998) Glas im Bauwesen Verbundglas und Verbund-Sicherheitsglas Teil 5: Maße und Kantenbearbeitung (ISO 1254-5 : 1998) This European Standard was approved by CEN on 1998-01-11. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. The European Standards exist in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. ÈÉË European Committee for Standardization Comité Européen de Normalisation Europäisches Komitee für Normung Central Secretariat: rue de Stassart 6, B-1050 Brussels 1998. CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national members. Ref. No. EN ISO 1254-5 : 1998 E
Page 2 EN ISO 1254-5 : 1998 Foreword International Standard ISO 1254-5 : 1998 Glass in building Laminated glass and laminated safety glass Part 5: Dimensions and edge finishing, which was prepared by ISO/TC 160 Glass in building of the International Organization for Standardization, has been adopted by Technical Committee CEN/TC 129 Glass in building, the Secretariat of which is held by IBN, as a European Standard. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, and conflicting national standards withdrawn, by November 1998 at the latest. In accordance with the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, the Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, the Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, and the United Kingdom. Endorsement notice The text of the International Standard ISO 1254-5 : 1998 was approved by CEN as a European Standard without any modification. 2 6 9 10 10 12
Page EN ISO 1254-5 : 1998