MAJOLICA PORTO Installation Instructions

MAJOLICA PORTO Installation Instructions MAJOLICA PORTO Basin EX-SB 1* [single tap type] EX-SB 2* [double tap type] Water faucet kit EA-SB P1 [P pipe / single tap type] EA-SB P2 [P pipe / double tap type] EA-SB S1 [S pipe / single tap type] EA-SB S2 [S pipe / double tap type] Contents Before installation Usage conditions Content of packing Transporting the unit Unit installation 1 Wall fittings 2 Water regulator&thermostat 3 Drain housing 4 Shower head holder 5 Neck base 6 Basin 7 Flexible pipe 8 Shower hose 9 Drain pipe 10 Tap & Knob 11 Neck cushion 12 Testing the unit After installation 13 Sealing 2 5 6 8 8 9 10 13 14 14 15 16 18 18 20 22 23 26 26 (Above drawing is EX-SB 1*/EA-SB P1) To the installer The instructions should be thoroughly read and understood before installation to ensure that MAJOLICA PORTO is installed correctly. After installation, please pass these instructions to the customer. To the customers Customers must ask professional to install MAJOLICA PORTO. Customers must not install MAJOLICA PORTO by themselves These instructions should be stored in a safe place for future reference. (Above drawing is EX-SB 2*/EA-SB P2) PORTO, The data for the MAJOLICA including images and dimensions listed in this manual may be modified and are subject to change without prior notice. The precautions listed here are to ensure that MAJOLICA PORTO can be installed safely, and to prevent any danger or risk to the person installing MAJOLICA PORTO or those around them. All of these precautions are important for safety. Takara Belmont is not responsible for any damage or risk to the person installing MAJOLICA PORTO or those around them should accidents occur following non compliance with the following guidelines and precautions. If MAJOLICA PORTO is installed after ignoring this symbol, there is the risk of light or moderate injury or physical damage Note: Plumbing should be performed by a qualified technician and should meet all national and local plumbing codes and ordinances. It is the responsibility of purchaser and/or plumber to conform to national and local codes and ordinances. Takara Belmont does not take any responsibility or liability for plumbing and installation. 1 Version 2 November, 2013

Before installation <Dimensions> (unit : mm) Top View(Single tap type) 640 615 195 Top View(Double tap type) 640 615 225 150 535 125 200 Front View(Single tap / Double tap type) Side View(Single tap / Double tap type) 625 265 791 Height of neck fittings 820 Neck height including neck cushion 890 240 535 80 125 200 Above picture is single tap type <Plumping layout> Front View(Single tap / Double tap type) Basin bracket 350 Hot water supply Rc 1/2 Water supply Rc 1/2 Side View(Single tap / Double tap type) Melamine facing plate Above picture is single tap type Reinforcement Solid wood 30 300 125 12 Hooks 750 445 Ф32 Ф32 95 90 570 820 Neck height including neck cushion 300 600 75 Measurements including the neckrest height will vary 2 140 200 Lumber core (thickness:18) or composite panel(thickness:12)

<Parts structure> Unit <Single tap type> Shower head Drain cap Strainer Shower head holder Tap Basin Mixer pipe Neck cushion Stop cock Shower hose Drain housing Trap Temperature control knob <Double tap type> Shower head Shower head holder Drain cap Strainer Temperature control knob Tap Mixer pipe Basin Neck cushion Shower hose Drain housing Stop cock Hot water pipe Water pipe Trap 3

Floor surface Ensure that the material or finishing of the floor surface is waterproof material or has a waterproof coating applied. Always ensure that the floor surface is horizontally level. Ensure that the floor surface is smooth and free from bumps around the attachment areas. Wall For installation on the wall, the wall base strength should be equal to or stronger than a 42mm-thick composite panel. If the wall is made of plaster or its thickness is less than 42mm, add a wooden reinforcement onto the wall(see page 2). Use a waterproof material such as melamine for the wall surface (for possible water splashes during shampoo treatment). Ensure that the wall surface is vertically straight (if not, it might affect the neck height of the basin or cause poor drainage). Raising pipes Always use a rigid PVC pipe and rigid PVC pipe joint(vu40/vp40) when raising a drainpipe. After the installation, ensure that the drainpipe is stable. Always attach a rubber bush(not included) when raising a drain pipe for the wall (or the floor) Always attach a stop cock mounting bracket(not included) when raising a water supply pipe and a hot water supply pipe Stop cock mounting bracket Pipe(VU40 / VP40) Joint(VU40 / VP40) Pipe(VU40 / VP40) Piping specification Stop cock mounting bracket Rubber bush Hot water / water supply Rc 1/2 Drainage VU40 / VP40 Waterproofing In case of the installation on the first floor of higher,waterproof the floor appropriately (e.g. do water proofing work, use a floor tray made of stainless steel, set up a water leak sensor, etc.) Installation of pipes The following points are important to adhere to during the installation of pipes. Read through the details carefully and ensure that the pipes are installed correctly. When installing this product, ensure that installation of pipes adheres to the instructions outlined in "Precautions during installation of pipes". Installing pipes without reading through the precautions will mean water may not mix properly, and a set temperature will not be achieved. This product is designed for indoor installation only. 4

Precautions during installation of pipes Do not use pipes made of materials that may cause rust in the water supply pipe. In general, VP pipes or other materials specified by regulations for a particular region, are recommended for installation. In general, Type L deoxidized copper pipes are recommended for hot water pipes. In general, the same diameter and same pressure is recommended for hot water pipes and water supply pipes. Always use a reamer to deburr the ends of cut pipes. Avoid using inverted U-shaped pipes (siphon) as these can cause air to become trapped. Always connect hot water pipes and water supply pipes after removing all contaminants such as dirt, sand and oil as these can cause problems. After connecting the pipes and testing water flow, clean the filter and shower head. Ensure that the drain pipe is installed at a gradient of 1/50 for a diameter of φ75or less, or 1/100 for a diameter of φ75 or more. Do not connect the hot water pipes and water supply pipes in reverse. Connecting pipes in reverse will mean the temperature of water cannot be controlled properly by the water taps, which may cause scalds or burns. Ensure that the hot water pipes from water boilers are only run over a short distance so as to minimize resistance. Longer pipes can cause fluctuations in temperature and poor hot water delivery. Always wrap pipes with lagging material after installation is complete. Water boiler pipes In general, the same diameter and same pressure is recommended for main hot water pipes and main water supply pipes. Ask a professional to install a water boiler. The equipment comes with a strainer installed. Usage conditions Hot water supply and water supply conditions Water used Hot water supply, water supply pressure Hot water temperature into the product Water boiler Public water supply (do not use non-drinkable well water or water that contains rust or sand.) If the water hardness is 80 ppm or higher, install a water softener to prevent the buildup of scale within the basin body. Aeration may be minimal when using shampoo even if drinkable well water is used, so a water softener should be installed. 2 Use a pressure between 0.1 and 0.4MPa(1 4kgf/cm ). If multiple MAJOLICA PORTO units are used, ensure that the pressure does not drop 2 below 0.1MPa(1kgf/cm ) Set the water supply pressure hot water supply pressure. Set the difference between the hot water supply pressure and water supply 2 pressure to within 0.2MPa(2kgf/cm ) Set the hot water temperature to 80 or less. Set the temperature 10 or higher than the shower temperature used. Do not use steam with the hot water supply 5

Content of packing installation. Please check all below parts are included before <1. Water plumbing kit> Packing details <Single tap type / Double tap type> Drain housing Trap P-trap / S-trap Shower hose Either of the two type (Rubber packing is included) P-trap S-trap Basin bracket Scerw set for basin bracket Hooks (Screw(2) is included) Wrench Cover(large) sheet for connecting flexible pipe Written in Japanese <Single tap type> <Double tap type> Stop cock (2) Thermostat Stop cock (2) Thermostat Cover (small)(2) Water pipe (2) (L=45mm) Cover (small) (2) Thermostat packing (black), Screw <2. Neck cushion parts> <Single tap type / Double tap type> Neck fittings Neck cushion Operation & Instruction Manual 1. Water plumbing kit Neck base [It has two packings in the reverse side (2)] 2. Neck cushion 2. Neck fittings, Neck base 3. Basin assembly kit 6

<3. Basin assembly kit> Packing details <Single tap type> Water regulator Nut Packing(black, 2) Conversion adaptor (1) Shower head holder Packing(white) Tap cap (1) Tap Flexible pipe (1) Packing(black) label Written in Japanese Screw set (L=200mm) <Double tap type> Water regulator Nut Packing(black, 2) Conversion adaptor (2) Shower head holder Packing(white) Packing(black) Temperature control knob Tap Tap cap (2) label Written in Japanese Elbow Handle lock(black) Thermostat nut (With packing) Thermostat packing (white) Screw set Flexible pipe (3) (L=200mm) 7

Transporting the unit Carrying tap parts set Some parts are metallic or plastic. Do not drag or drop the outer packing. Doing so may cause damage and break to these parts. Take extra care if opening the boxes with a sharp object such as a knife, so that the inside parts do not get damaged. Carrying basin Take care when handing the basin as it is heavy and fragile. Don t drag the basin. Doing so may cause damage to the floor surface or crack the basin itself. Unit installation *Please make sure that this product is installed in the correct order as listed below. Failure to follow these instructions may result in an inability to install the basin. * Contents may vary depending on model specified. Chart flow of unit installation 1. Wall fittings 8. Shower hose 2. Water regulator & Thermostat 9. Drain pipe 3. Drain housing 10. Tap & Knob 4. Shower head holder 11. Neck cushion 5. Neck base 12. Testing the unit 6. Basin 7. Flexible pipe After installation Check each item on the checklist 13. Sealing 8

1 Wall fittings Attach 1 stop cock 1. Check the position of drainage pipe for floor, based on the installation position of the basin (Basin in the centre). Check if the stop cock mounting brackets are attached on the wall. To check the position of drainage pipe riser, hot water supply and water supply refer to the dimentions. (See page 2) 2. Mark the position to fix the basin bracket and hooks. When replacing the tap parts from other equipment, if the stop cocks do not have a filter inside, change it to the provided stop cocks with a filter. Stop cock mounting bracket closeup Drainage pipe for floor Basin in the centre Hot water supply Water supply Drainage pipe for wall Floor <Single tap type> 3. Apply thread seal tape to the screws of the stop cocks (which are closer to the wall) with seal tape. 4. Attach the covers(small) on the stop cocks and install them on to the wall. Make sure the taped surface faces the ceiling. Make sure to remove a cap from each stop cock before the installation. packings. Do not remove rubber wall. Make sure the covers(small) touch the 5. Secure the thermostat on to the water stop valve Mount the stop cocks in the way that the - lines become vertical to the floor. Label face up Stop cock Rubber packing Cap Thermostat Cover(small) <Double tap type> 3. Apply thread seal tape to the screws of the water pipes with seal tape(both sides), and connect them to the stop cocks. C H 4. Attach the covers(small) on the water pipes and install the stop cocks in the way that the flexible pipes connecting ports face the ceiling. wall. Make sure the covers(small) touch the Mount the stop cocks in the way that the - lines become vertical to the floor. Flexible pipe connecting port Water pipe Cover(small) Stop cock 9

Attach 2 basin bracket 1. Temporality fix the basin bracket on to the wall, with the supplied wood screw and flat washer into the centre of the bracket. 5.8 63 Wood screw...1 15.5 1.5 1.5 Flat washer...1 2. Level the basin bracket. Wood screw Flat washer Basin bracket Level gauge Check if the wood screw fits in the slotted hole of the bracket. 3. Tighten the wood screw in the centre, Secure it with 4 other wood screws. 5.8 63 Wood screw...4 Wood screw 2 Water regulator & Thermostat Place the basin mounting surface on the floor for easier installation Ensure to put the basin on the floor gently, after spreading a cushioning material, to avoid damaging the basin. Basin Floor Cushioning Basin mounting surface 10

<Single tap type / Double tap type> Attach 1 the water regulator 1. Remove the packing (white, 1pc) and nut from the water regulator. (black). Do not remove the packing 2. Attach the packing(black, 2pcs) on to the water regulator, and insert it into the water regulator hole in the basin. 3. Put the packing(white, 1pc) back to the water regulator, and fix it onto the basin by tightening the nut. The packing(black, 2pcs) are included in the basin assembly set. Nut Packing (white) Packing (black) Water regulator Water regulator packing(black) Pay attention to the direction of water regulator and the order you attach the packing. If it is done incorrectly, it may result in a water leak or affect the connectivity of other parts. Make sure to insert the water regulator into the correct hole in the basin(double tap type). Water regulator Basin Water regulator hole Packing(black), 3 Nut Packing(white) Basin for single tap Water regulator Water regulator Basin Shorter tube face drain hole Basin mounting surface for the wall Attach the centre of the water regulator vertically to the basin mounting surface for the wall Drain Basin mounting surface for the wall 11

<Double tap type> Attach 2 thermostat Thermostat packing(black) 1. Attach the elbow onto the thermostat. elbow. Pay attention to the direction of the 2. Put the thermostat packing (black) on top of the thermostat, and insert it into the thermostat hole in the basin. 3. Put the thermostat packing (white) on top of the thermostat and fix it onto the basin by the thermostat nut. The thermostat packing (white, 1pc) and the thermostat nut are included in the basin assembly kit. Elbow Thermostat Packing never loosen and remove these nut Attach the elbow in the same direction as the flexible pipe connecting port Pay attention to the direction of thermostat and the order you attach the packings. If it is done incorrectly, it may result in water leak or affect the connectivity of other parts. Do not loosen or remove the grey nut from the thermostat. Thermostat hole Thermostat Water regulator Thermostat packing(black) Basin Thermostat nut Thermostat packing(white) Water regulator Thermostat Thermostat Basin Basin mounting surface for the wall Basin Attach the thermostat parallel to this face Drain Elbow face drain hole 12

3 Drain housing Remove 1 the drain housing nut, packing(white) and triangular packing(black) from the drain housing (black). 1 Do not remove the U-packing 2 Remove the drain cap and strainer from the drain housing when inserting it into the basin. Otherwise they might pop out and damage the basin and the floor. U-packing(black) 1:Don t remove Triangular packing (black) Packing(white) Drain cap Strainer Drain housing nut Seal 2 the drain housing Apply moderate quantity of sealant agent. If it is too much, it might flow over from the drain housing and the bowl, which may encourage color stains or other smudges. Drain housing Guide of sealant quantity U-packing(black) Sealant Correct incorrect Insert 3 the drain housing into the basin, and fix it with the triangular packing(black), packing(white) and drain housing nut. Drain housing Drain housing nut Packing(white) Triangular packing (black) Smaller diameter face drain housing U-packing(black) Pay attention to the order you attach packings. If it is done incorrectly, it may result in a water leak. If the sealant overflows from the drain housing and basin, and adheres to the basin surface, remove it completely. Otherwise it might encourage colour stains and other smudges. 13

4 Shower head holder Make sure to follow the instructions below in order to avoid damaging the shower head holder. Put the screws into the shower head holder completely straight and fix them. Do not overlighten the screw. Do not use an electric drill. Check if the shower head holder has a packing in the reverse side. If not, it may result in a water leak. If the packing is not found, please contact your closest dealer. Attach the Shower head holder, facing the trap housing in the basin [the reverse side of shower head holder] Packing 4 12 Self tapping screw...2 5 16 1.0 Washer...2 Drain housing Fix them by cross slot screwdriver Washer(5 16 1.0) [4 12]Self tapping screw Shower head holder Attach it, facing towards the drain housing in the basin 5 Neck base Don t overtighten the screws. Don t use an electric drill. Check if the sneck base has packing in the reverse side. If not, it may result in a water leak. If the packing is not found, please contact your closest dealer. Attach the neck base facing the chair side. If there is a space between the basin and the neck cushion, water might spill over from the basin. [the reverse side of neck base] Packing Attach the neck base facing the chair side. Fix them by cross slot screwdriver M5 25 Bolt...2 5 20 2.0 Washer...2 Chair side [M5 25] Bolt Washer(5 20 2.0) Neck base Attach it facing the chair side Basin side 14

6 Basin Fit 1 the basin into the basin bracket Make sure the basin is fitted onto the basin bracket securely in order to avoid the basin from dropping against the floor and causing injury. Basin Level 2 the basin (horizontal direction) by using the level gauge, and fix it with the hooks. 5.8 50 Wood screw...2 [5.8 50] Wood screw Hooks The hole of basin mounting surface for wall Basin bracket Hooks Correct Incorrect Incorrect Make sure the hooks touch the bottom ends of the holes in the basin (facing the wall), and fix them with the screws. Do not reverse the hooks. If the above is not done correctly, the basin might become unstable, which may cause injury. Level gauge This face needs to be horizonal Install 3 the strainer in and the drain cap on the drain housing Drain cap Strainer Drain housing 15

7 Flexible pipe <Single tap type> 1. Bend the flexible pipe in the way that it fits the thermostat and water regulator. 2. Put a provided packing on the flexible pipe, and attach it to the water regulator. 3. Put another provided packing on the flexible pipe, and attach it to the thermostat. Water regulator Packing Flexible pipe Packing Thermostat 16

<Double tap type> 1. Bend the flexible pipes in the way that they fits the thermostat, water regulator and stop cock. Thermostat Water regulator 2. Put a provided packings on the flexible pipes, and attach them to the water regulator. Attach them in the order of 1 Make sure to use the provided packings.without them, it may result in a water leak. Do not connect the hot water and cold water in reverse. Make sure the hot water pipe and the water pipe do not touch each other. Do not attach the flexible pipes on the shower hose side on the water regulator. Doing so might prevent water from coming out and cause water leak. 1 2 5 4 Packing 3 6 Flexible pipe Packing There is a caution label at the shower hose side on the water regulator. Stop cock label label It means shower hose connecting port in Japanese. 17

8 Shower hose Put the shower hose through the shower head holder, and attach the hose and to the shower hose connecting port. Shower head Shower hose connecting port Water regulator Shower head holder Shower hose 9 Drain pipe 1. Remove the nut A and the paper packing from the trap, and insert it in P-trap or S-trap. Pay attention to the direction of the nut A when removing it from the drain pipe and inserting it in the trap. 2. Loosen the nut B on the trap, and temporarily fix it on P-trap or S-trap and the drain housing (see page 19) 1 Nut B *Don t remove it Trap Nut A Paper packing *If P-trap or S-trap is too long, cut it to an appropriate length. Nut A Closeup *Insert its thread side to the P-trap/S-trap P-trap (or S-trap) 18

3. Detach the temporarily fixed parts, attach a rubber bush (not included) on the drainage pipe riser. 2, 5 S-trap type P-trap type 4. Put the P-trap or S-trap through the cover(large), and insert it in the rubber bush (not included). 5. Attach the trap to the P-trap or S-trap and the drain housing. Plastic packing Rubber packing Cover(large) trap. Make sure the shower hose comes above the floor). Make sure the cover touches the wall (or the S-trap Paper packing P-trap Cover(large) Trap Pay attention to the position of packing and the order you attach the packings. If it is done incorrectly, it may result in a water leak. Closeup 5 3, 4 S-trap type P-trap type Shower hose S-trap Drainage pipe rises (VU40/VP40) P-trap wall Trap Make sure the shower hose comes above the trap. If not, the trap might not be connected properly, or the shower head cannot be taken out from the shower head holder. floor Cover(large) Cover(large) Rubber bush (not included) floor Drainage pipe rises (VU40/VP40) wall Rubber bush (not included) 19

10 Tap & Knob Precautions for Resin(Plated) Parts Resin plating is used for the tap and the temperature control knob. Plating in a thin and metal film applied to surface may crack or peel due to corrosion or aged deterioration. Flaws or cracks may occur on the plated surface due to impacts from falling objects. Flaws or cracks may occur on the plated surface when a hard object hits the surface. Peeling of the plating may occur from flaws or cracks on the plated surface. Check to ensure that there are no flaws, cracks, or peeling of the plated surface of the tap, etc. before using the product. If peeling is observed, immediately stop using the product and contact the closest dealer. Continued operation may result in injury. Example of flaws on the plated surface Example of peeling of the plated surface Tap 1 <Single tap type / Double tap type> 1. Attach the conversion adaptor to the water regulator. 2. Attach the tap to the conversion adaptor and fix it with the screw. positions. Pay attention to the parts M4 20, Pan head screw 1 Screw lock (Blue) Tap cap Fit in the dent of tap and conversion adaptor [M4 20] Pan head screw 3. Place the tap cap on the tap top. top. make sure the cap is placed straight onto the tap Tap Conversion adaptor Correct Incorrect Water regulator 20

<Double tap type> Temperature 2 control knob 1. Attach the handle lock to the thermostat. directions. Pay attention to the parts mounting Nail(long) Dent(short) Fit in the nail of handle lock and the long dent of thermostat Dent(long) 2. Attach the conversion adaptor to the thermostat. directions. Pay attention to the parts mounting Tap cap Fit in the centre plane of conversion adaptor and the red line of thermostat Centre plane [4 16] Pan head self tapping screw Correct Incorrect Temperature control knob 3. Attach the temperature control knob to the conversion adaptor, and fix it with the screw. directions. Pay attention to the parts mounting Conversion adaptor [4 16], Pan head self tapping screw 1 Handle lock Fit in the dent of temperature control knob to the conversion adaptor Thermostat 4. Place the cap on the temperature control knob. Make sure the cap is placed straight onto the top of the temperature control knob. Correct Incorrect 21

11 Neck cushion Attach the neck cushion 1. Check the proper direction of the neck cushion and the neck fittings. 2. Hold the neck cushion, and fit it to the centre of neck fittings. Overhead view Basin side Neck fittings Basin side Chair side Neck cushion Chair side Cutaway Chair side 3. Adjust the height of neckrest fittings and right and left edges of neck cushion. (both sides) Adjust the height 4. While pulling the neck cushion, secure it with the hooks (2 locations). As shown in the below illustration, secure the hooks at the bottom of neck fittings. Neck fittings Adjust the height Fix the hooks at the bottom of neck fittiings Cutaway Hook 5. Insert and secure the neck fittings to the neck base. Pay attention to the proper direction of neck fittings. The surface of neck cushion with cutaway to be faced to the chair side. Cutaway Basin side This side with cutaway should come to the chair side. Chair side Neck base When the neck fittings are put on the neck base, check if the neck cushion does not touch the basin, and if the neck fittings can go into the neck base smoothly. Otherwise the neck cushion might be come damaged. In case of such problems, move the neck base slightly towards the basin (away from the chair side) are re-fix the neck base so that the neck cushion Neck base does not touch the basin. Attach it towards the basin side a little. Basin side Chair side Fix it by cross slot screwdriver [M5 25]Bolt Washer(5 20 2.0) 22

12 Testing the unit Test 1 water flow Always test the water flow to prevent accidents during use. Test the water flow and inspect the following items. The hot water may be slightly tainted at the start of the water flow test, however, this does not indicate any problem. 1. Is there no water leaking from the pipe joints? 2. Are the hot water supply and water supply pressures at the same, stable pressure? (See page 5) If the pressure are not the same, see How to adjust faulty temperature regulation below 3. Can temperature be controlled properly? If not, see page 24, 25 and set up the temperature control knob 4. Check that the shower outlet flow is sufficient, by the following as a guide for flow rate. Shower outlet flow rate: <Single tap type> Approximately 16L/min <Double tap type>approximately15l/min Cleaning 2 After the hot water becomes clear during the water flow test, always clean the filter (within the stop cock) and shower head. Failure to do so can result in insufficient flow rate and faulty temperature regulation. During the cleaning, ensure not to damage or lose the packings. Remove any trapped dirt and clean the shower head Aerator core Packing Shower head Remove any trapped dirt and clean the shower head <Single tap type> Stop cock <Double tap type> Open Wrench Close Open Open Filter Close Wrench Wrench Filter Close Stop cock How to adjust faulty temperature regulation Contents of defect 1. Something wrong with hot water(temperature is unstable) 2. Hot water(high temperature) does not come out 3. Water(low temperature) does not come out Presumed cause 1. There is difference in the water supply or hot-water supply pressure, or the pressure of hot water supply is higher than the pressure of water supply. the pressure of water supply the pressure of hot water supply [The difference should be in the range of 0.2MPa] 2. Pressure of water supply and hot water supply is high 2 [These two should be in the range between 0.1 and 0.4MPa(1 4kgf/cm )] How to react Connect a pressure reducing valve (Optional) (It is recommended that water supply pressure and hot water supply pressure become the same pressure) 23

Set 3 up the temperature control knob In case the water temperature does not match the initial setting <Single tap type> 1. Turn the tap on anti-clockwise at the maximum degree. 2. Turn the temperature control knob until the water temperature reaches approx. 40, regardless its scale marks. In order to produce hot water, turn the knob while pressing the lock button. Open 3. Remove the cap and screw from the temperature control knob, and take the knob out of the unit. out. Do not turn the knob when taking it knob. If the bush comes out, re-attach it to the Tap If you use a precision screwdriver or other metallic tool to remove the cap, cover the cap with a plastic bag beforehand. Make sure the tool does not scratch the coated surface of the temperature control knob and the cap. If the coated surface gets scratched, broken or peeled, contact your closest dealer. The damaged coated surface might cause injury while in use of the equipment. Stop button C H Precision screw driver(-) Plastic bag Temperature control knob Temperature control knob 4. Put back the temperature control knob to the unit, so that the scale mark of 40 on the knob matches to the line on the thermostat. C H Cap 5. Check if the water temperature is approx.40. Bush Self tapping screw[4 16] Line H Temperature control knob C 40 24

<Double tap type> 1. Turn the tap on anti-clockwise at the maximum degree. Open 2. Turn the temperature control knob up to the lock position, and measure the water temperature. 3. Remove the cap and screw from temperature control knob, and take the knob out of the unit. Tap Tap cap If you use a precision screwdriver or other metallic tool to remove the cap, cover the cap with a plastic bag beforehand. Make sure the tool does not scratch the coated surface of the temperature control knob and the cap.if the coated surface gets scratched, broken or peeled, contact your closest dealer. The damaged coated surface might cause injury while in use of the equipment. Precision screw driver(-) Pan head self tapping screw [4 16] Temperature control knob Plastic bag Temperature control knob 4. Adjust the position of the conversion adaptor If the measured temperature was higher than 40 Shift the conversion adaptor anti-clockwise, and fix it on to the thermostat. If the measured temperature was lower than 40 Shift the conversion adaptor clockwise, and fix it on to the thermostat. When adjusting the conversion adaptor, adjust in small increments, otherwise it can result in a high flow of hot water, which may result in burns or scalds 5. Attach the temperature control knob to the conversion adaptor, and check if the water temperature is approximately 40 at the lock position. If it is not approximately 40 Repeat 4. Water temperature is low Red line Centre plane Water temperature is high 6. Fix the temperature control knob and the conversion adaptor with the screw. 7. Place the cap on the temperature control knob. 25

After installation Inspection Be sure to execute the inspection without fail to prevent accidents during operation 1. Check that there are no missing screws or other parts. 2. Check that there are no loose parts If any part is loose, check the bolts at the joints again. 3. Check that there are no cracks or contamination on the basin. 4. Check that there are no problems, such as flaws on the external appearance. 5. Check that there are no water leaks on the floor. 6. Check that there are no longer gaps between basin and wall. 7. Put drops of water on the shower head holder and neck base to check that there are no water leaks. If water leaks are observed : Check that the screw and washer are tightened Check that the packing is attached. 8. Check that the neck cushion does not touch the basin and can be inserted smoothly, when putting the neck fittings on the neck base. If such problems are observed, adjust the position of the neck base. (See page 22) 13 Sealing Seal the gaps(the width of sealing : approximately 5mm) sealing. Put masking tape on the gap between the basin and the wall before the Ensure to seal the gap between the basin and the wall completely. Check that there are no cutaway found in the sealing. If the sealing is not complete, the wall might become corroded by penetrating water. 26

Memo 27

TAKARA BELMONT CORPORATION 1-1, 2-Chome, Higashi-shinsaibashi,Chuo-ku,Osaka,Japan TEL : (06) 6213-5945 FAX : (06) 6212-3680 Printed in Japan 28