R G--D HIGH SPEED MEDIUNM ND HEVY DUTY OMPOUND FEED LOKSTITH SEWING MHINE OPERTION INSTRUTION / PRTS MNUL
.Main technical specifications pplication: medium and heavy-duty Max sewing speed :000 spm Max stitch length: 0~mm Presser foot lift: hand.mm,knee controlled mm Needle: Model DPX#~# Hook: big rotating hook Lubrication:auto lubrication Motor power 0W (clutch motor)..preparation ()leaning machine lean off the grease and dusts on the Surface of machine with gasoline and soft cloth. ()Inspection efore use a thorugh inspection should be done upon the machine.turn balance wheel slowly to see if there is any obstruction,collision and uneven resistance between pars. If there is, adjustment should be done before operation..installing the motor(fig.) lign machine balance wheel belt groove () with motor pulley belt groove () by moving the motor ( ) leftward of rightward. e sure the belt is not touch with table..onnecting the clutch lever to the pedal (Fig.) a. The optimum tilt angle of pedal with floor is approx degree. b. djust the clutch of the motor so that clutch. lever ( ) and draw bar () run in line as Fig., the machine would have stabel motion and long using. c. The machine balance wheel should rotate counter clockwise for normal seweng when view from opposite side of the balance wheel. The motor rotates in the same direction. The rotation can be reversed by reversing (turm over 0 deg.) the plug of the motor. d. djust the tension of V-belt F by moving the motor vertically. The proper tension if V-belt is a slack of 0 ~ mm when the belt is depressed (at the belt pan) by finger. G F E D 0~mm --
.Installing belt guard(fig.) The belt guard should be installed for safety..installing the bobbin winder (Fig.) lign pulley () of the bobbin winder with the outside of the belt, and there should be a proper clearance between them, so that pulley () can be contacted with the belt when stop latch thumb lever () is depressed, thereby the belt drives pulley () while the machine running, the bobbin winder should be parallel with belt slit (E) of the table, then fasten with two wood screw (D). E D D.Lubrication(Fig.) a.oil amount Oil amount must be oiled according to the mark of drip pan. Mark () is the highest situation, Mark () is the lowest situation, Note that oil amount couldn t be lower than mark (), otherwise all parts of machine will apper heat and dead point for not gaining oil. b.oiling In lubruation, H- sewing mcahien oil or HJ- machine oil must be used. efore running, the machine must be oiled at the mark(). c.hanging Turn off the screw plugs( ), clean up the dirty oil and the dust of drip pan, then fasten the screw plugs ( ), add fresh oil --
.Trial run (Fig.) The machine is designed specially with plunger automtic lubricating system, so it can run with normal speed. In ordervto increasing the using time of machine, when the machine left outvof operation for a quite long time is used again. Turn off the rubber plug top of the machine head, oil it thoroughly, then lift the presser foot and run at a low speed with 00 spm, observe the spurt through oil flow window, as the lubrication si well, keep the running test at the low speed about 0 mintues, increase the speed gradually, after month s running, according to the conditions which operate, then increase up to proper sewing speed. --
.Rotating hook okl amount adjustment (Fig.) The hook oil amount can be adjusted by screw (). Turn it clockwise ( + ) to increase amount: counter-clockwise ( - ) to decrease. The oil amount is adjusted in the range of five turns of screw (): Tightning for more; Loosening for less. 0.Oil pump suply adjustment (Fig.) Generally no adjustment is for oil pump. When the machine is running at a low speed, observe the oil screen. If no oil splashing, close the clearance. djusting plate Standard clearance 0.-.0 y-pass oil hole --
.Installing the needle (Fig.) Turn the balance wheel to lift the needle bar to its highest point, loosen needle set screw, making the needle groove turn to the left side of an operator, fully insert the needle shank up to the bottom of needle socket, then tighten needle set screw. Note: Fig. (b) insufficient insertion Fig. (c) Wrong direction of groove Long groove leftward a learance b c.oordination among the needle the thread and the material (Fig.0) The needle thread is left-twisted, the bobbin thread is left or rigth-twisted. Holding the thread, twist it with right hand in the direction of arrow shown in Fig.0, if it is tight, it is left-twisted, contrarily, it is right-twisted. The Needle is DP X or X Nm 0 ~ 0 the needle number must be fitted for the materials. Sewing too heavy the weight of materials. The needle would be breaking and skipping stitch and thread breaking for its too thin, if the needle is too thick, it would damage the clothes for its large needle hole. Therefore, the selection of needle and thread must be fitted for the materials. 0.Threading the needle thread (Fig.) When threading the needle thread, raise the needle bar to its highest position, lead the thread from the spool and pass it in the order instructed (Fig.) () Lead the thread from the spool, pass down through the right side of thread guide plate, to left pass up thru the middle hole of thread guide plate, to left pass thru between two small tension disc and pass down the left hole of thread guide plate. --
() To left pass down thru the right hole, to left up thru the middle hole and to left down thru the left hole of thread retainer. () Pass down thru between two tension disc. () To left and up pass thru the hook of thread take-up spring. Turn to left pass thru underneath slack thread regulator, then up pass thru thread guide and up to left pass thru the hole of thread take-up lever. () Turn down to left pass thru thread guide, pass down thru thread guard of the needle bar bushing ( lower ) and needle bar thread guide 0, then pass the thread from the left thru the eye of needle, afterwards, draw out the thread from the needle eye approx 00mm. When drawing the bobbin thread, hold the tip of the needle thread by hand, turn the balance wheel to lower the needle bar and then to lift it to its highest position. Pull the needle thread and then the bobbin thread is drawn up. Put the tips of the needle and bobbin thread toward front under the presser foot. 0.Winding adjustment (Fig.) The wound bobbin thread should be neat and tight. If not, adjust the thread tension by turning tension stud thumb nut of the bobbin winder tension bracket (). If the wound bobbin is not neat, tension bracket (). can be moved to be adjusted. When adjusting, loosen screw () first, then move the bracket leftward or rightward if the thread is wound to one side as shown in Fig. (b), move the tension bracket rigtward, while if the thread is wound to one side as shown in Fig. ().move the tension bracket leftward until the thread is wound neatly as shown in Fig.(a), tighten screw (). Note: Nylon or polyester thread should be wound with light tension. Otherwise bobbin (D) might be broken or deformed. Don t overfill the bobbin, because it make its thread loosening down from the bobbin. The optimum capacity of thread will fill about 0% of bobbin outside diameter, and this can be adjusted by stop latch screw (E). a b c d D E --
.Setting the stitch length and controlling the reverse sewing (Fig Stitch length can be set by turning stitch length regulating dial (). The stitch length is longer when turning stitch length regulation dial () counter clockwise. nd the stitch length is shorter when turning dial () clockwise. The figures on the stitch length regulation dial plane () indicate the stitch length. Reverse sewing can be obtained when feed reverse lever () is depressed and forward sewing can be restored automatically when feed reverse lever ( ) is released..thread take-up oiling(fig.) Thread take-up area adopts woolen thread oiling. fter long timi of use, function lost, so replace with a new one. Open the face plate, remvoe the pressure screw, lock nut and presser bar. Remove Hinge () and lever (). Draw out Oil Wick (). Loosen the wick fix screw on thearm top, and take out Set Plate (D). Replate with a new one. Installing is a reverse sequence. D.djusting the pressure of presser foot (Fig.) Pressure on presser foot is to be adjusted in accordance with materials to be sewn. Loosen lock nut (). If heavy materials to be sewn, turn pressure regulating thumb screw clockwise as shown Fig.0 (a) to increase the pressure. While light materials to be sewn, turn the pressure regulating thumb screw counter clockwise as shown in Fig.0 (b) to decrease the pressure on presser foot, then tighten lock nut (). The sewing materials must be feed normaly with proper pressure of presser foot and the pressure should be decreased as possibly. a b --
.djusting the thread tension (Fig. ) In general, the thread tension is to be adjusted in accordance with materials thread and others. In practice, the thread tension is adjusted according to the stitches resulted and has the normal stitches. The needle thread tension should be adjusted with referance to the bobbin thread tension. when adjusting the bobbin thread tension, turn bobbin case tension spring screw () ( Fig. ) clockwise for more tension or turn the screw counter clockwise for less tension. It is a common practice to check the bobbin thread tension. In case of polyester thread tex (s), hold the end of the thread and vibrate the bobbin case up and down. If the bobbin case falls down slowly (Fig.), the proper tension is obtained. The needle thread tension can be adjusted by changing tension of the thread take-up spring, tension of tension disc, and the position of thread guide, all these adjustments will be described as follows..djusting the thread take-up spring (Fig. ) The normal sewing range of the thread take-up sprina is ~ mm. For sewing light weight materials (short stitch), weaken the spring tension and widen the sewing range of spring, while for sewing heavy weight materials, strengthen the spring tension and shorten the sewing range of spring. ) djusting the thread take-up spring tension(fig.) Loosen tension stud set screw (), turn tension stud () clockwise to make the spring get more tension, or turn the tension stud counter clockwise to make the spring get less tension. fter adjustment, e sure to tight tension stud set screw (). The method of adjustment: Loosen set screw () first, then to turn tension stud () counter clockwise to reduce the tension of thread take-up spring () to zero, and to turn tension stud () clockwise until spring () just comes into contact with the stopper on the thread take -up spring regulator, then to further turn tension stud () clockwise by turn. fter adjustment, tighten tension stud set screw (). --
) djusting the sewing range of t hread take-up spring (Fig.) Loosen set screw (), turn tension complete () clockwise to increase the sewing range or turn tension complete () counter clockwise to decrease the sewing range. efore delivery, the thread take-up spring is properly adjusted, Readjustment is needed only in the case of sewing special materials or with special thread. -mm D 0.djusting the thread of needle thread & bobbin thread (Fig.0 ) The position of the thread guide affects sewing quality, so it must be adjusted according to the materials to be sewn. Thread guide position Leftward enter Rightward Material Heavy Medium Light a b c d e 0 Fig.0 shows the various type of stitch forms. Normal stitch form should be as shoun in Fig. 0(a). When adnormal stitches occur with pucke ring or thread breakage, the tension of needle thread and bobbin thread must be adjusted accoringly. (a) The needle thread tension is too strong or the bobbin thread tension is too weak, turn the tension regulating thumb nut counter clockwise to make the needle thread get less tension or tighten the bobbin case tension regulating screw with small plastic screw driver to make the bobbin thread get more tension (Fig.). --
(b) The needle thread tension is too weak or the bobbin threal is too strong, turn the tension regulating thumb nut clockwise to make the needle thread get more tension or turn the bobbin case tension regulating screw counter clockwise with small plastic screw driver to make the bobbin thread get less tension (Fig.) (c) Other abnormal stitches as shown in Fig.0 (d).(e), adjustment can be made which reference to the above methods..timing between the needle and the rotating hook (Fig..djusting the position of needle bar Turn the balance wheel to locate the needle bar () at its lowest position, remove the rubber plug in the face plate (), then loosen the needle bar () connecting stud clamping screw () and move the needle bar () vertically to locate the timing position (The timing position of the needle bar is : when the needle bar at its lowest position, the center of needle eye (D) coincide with inside surface (E) of bobbin case bolder as shown in Fig.). Tighten clamping screw (), plug the rubber plug. D E -0-
djusting rotating hook point timing with needle. The motive relation between rotating hook and needle affects the sewing quality. Standard timing relation is : turn the balance wheel to locate needle bar to its lowest position, and lift back.mm the rotating hook point (D) should be coincides with needle center line (), and hook point (D) is.mm above the upper edge (E) of needle eye. When adjusting the rotating hook point timing also to note the clearance between notch bottom of needle (D) and hook point () of approx 0.0min must be maintained. (Fig.) D E D.mm.mm 0.0mm.Removing and installing the rotating hook (Fig.) Lift the needle bar to its highest position, remove the throat plate, take down the needle and the bobbin case. Loosen rotaing hook bobbin case holder plsition bracket screw () and take down position bracket (), then loosen three set screws (D) of rotating hook, t this point, it took out the rotating hook, it would be obstructed by feed bar. So that turn the balance wheel first to raise the feed bar to its highest position, then take down the rotating hook slowly while to turn it to step aside of the feed bar, Installing the rotating hook can be done in reverse sequence. The projecting flange of the position bracket () should be engaged in the notch () of the bobbin case holder, and maintain a clearance of 0.~0.mm between projecting flange top and the bottom of notch while installing. 0.-0.mm D.Installing feed dog (Fig. ) When feed amount is at the max the front end of feed dog is near the front of throat plate slot, the gauge between the two is.mm this is the standard position of feed dog..mm --
To adjust the position of feed dog, move feed dog to the front end of throat plate. Loosen (See Fig.b), move feed dog support in the direction shown by arrow to adjust fter adjustment tighten. a b.feed dog horizontal djustment (Fig.0) Feed dog is 0.~.mm above the surface of throat plate horizontally. When sewing condition requires tilting, adjust like this: loosen Press against the slot of eccentric shaft with a screwdriver to turn eccentric shaft left and right. Tighten. The front of feed dog is higher, which can prevent perckering and no skipping. The front of it is lower, which can prevent material sliding and no breakage of bobbin thread. Mark Eccentric shaft mark position Feed dog 0 Horizontal Standard bove Under The front up to the max Thefrontdowntothemax.Stitch length error adjustment (Fig.) Loosen () and (), take out the link pin, and loosen () to adjust am (D) with a screwdriver through the crank hole. Turn right: forward stitch length shorten reverse stitch length enlarged; Turn left: forward stitch length enlarged reverse stitch length shorten. D --
.Feed timing (Fig. ) Standard position Turn balance wheel to lower Feed dog till it is horizontal with the surface of throat plate, at the moment, the tip of needle should be horizontal with the surfaces of throat plate and feed dog. djustment can be done by adjusting the position of feed cam and feed dog lift cam. Installing feed dog lift cam (See Fig.) Open the back side cover, turn balance wheel by left hand counter-clockwise, take as for standard, the center of is slightly a little lower than the center of. Insatlling feed cam (See Fig.) ontinously turn balance wheel, take screw as for standard, the center of is slightly a little higher than the center of. --
.djusting the tension releasing mechanism (Fig.) The tension discs should be pushed apart to open when the presser foot is lifted. ut the open timing of the tension discs can be adjusted as follows: Romove face plate and the rubber plug at rear side of arm and loosen screw () of the knee lifting lever (left), then the tension releasing cam can be moved leftward or rightward when the cam is moved rightward, it is later to open, otherwise it is earlier to open. Left Right D.djusting feed timing of needle bar, Presser foot and feed dog (Fig. ) () Lift presser foot, make the stitch length to the maximum, turn balance wheel slowly to lower needle down into hole of feed dog, observe whether needle is at the center of feed dog hole or not. Forward Stitch length () Keep on turning balance wheel, move the needle forward a stitch lengty. If the needle is at position, shows timing feed of the three; if at, indicates the feed amount of needldbar and presser foot is larger than that of feed dog, then reduce L; if at, indicates the feed amount of needle bar and presser foot is smaller than that of feed dog, ten enlarge L till the needle arrives at. L Needle --
.djusting presser foot alternate lift mechanism (Fig.) The alternate lift mechanism can be adjusted according to the nature of material in a certain range. Of common heavy and medium sewing machine, the presser foot lift amount is about.mm and that of the follow presser foot is within mm. The presser foot lift amount increase then the follow foot amount reduce; the presser foot lift amount reduce, then the follow foot lift amount increase. ccording to the sewing process, to increase the presser foot lift amount and reduce the follow foot lift amount, loosen the screw for crank and turn down the crank slot with referance to the presser foot lift shaft, otherwise turn up. The adjustment is limited in a range and not too. bove Under 0.djusting the lift amount of presser foot with the follow presser foot (Fig Loosen nut, then adjust the center distance between the presser foot lift shaft and the screw of the nut. To increase the lift amount of the both feet, then reduce ; on the countrary, the lift amount wil be reduced. The adjustment is limited in a range and not too large. fter the adjustment, tighten the nut. bove Under --
.djusting the clearance between presser foot and follow presser foot (Fig. In sewing operation, for prevent the follow presser foot from striking on presser foot at the end of feeding, a proper clearance of approx. mm should be maintained between them. When the clearance is too small or too big necessary to adjust, loosen the crank clampin screw and turn down the needle bar shaft, then the follow presser foot move near the presser bar, and note the needle and the needle hole center ofeed dog, see the figure if the needle is off the hole center, then loosen feed crank set screw, move the feed dog to the right position. fter the adjustment, tighten the set screw. For the right and left position, to loosen screw () to obtain. Up Down 0.Periodical cleaning (Fig. ) lean the feed dog the rotating hook, the bobbin case, the oil pump filter screen and the like perodically according to customer s usage..leaning the feed dog Remove the throat plate, clean off all the dust and lint on the slit of the feed dog, the installing the throat plate. leaning the rotating hook lean off all the dust around the rotating hook, and clean the bobbin case with soft cloth. leaning the oil pump filter screen (Fig.) Take off the oil filter, clean off the dust of filter screen with gasoline. --
.rm and bed 0 0 0 0 0 0 --
Machine rm nd ed.rm and bed No. Part number Name Qt. Remark 0 0 0 0 0 WF-00 WF-00 WF-00 T-0a T-00 T-00 T-00 T-00 T-00 T-00 T-00H T-00 T-00 T-00D T-00D T-00D T-00E T-00D T-00D T-0 T-0F T-0F T-0F T-0F T-0F T-0F T-0F T-0F T-0F T-0F T-0F0 T-0F T-0 T-0 T-0 T-0 T-0 T-00 T-00 WF-00 T-00-0-0//Z -0-0//Z0-0-0//Z0 T-0G WF-00 WF-00 T-00D T-00 T-00 T-0 rm ed Trade Mark Rivet Face Plate Gasket For Face Plate Rubber Plug ( Φ) Rubber Plug Rubber Plug Thread Finger Oil Screen omplete Tree-eye Finger Thread Tension omplete Thread Pass-by Plate Tension Disc Spring Nut Set Thread Tension omplete Nut Spring Thread Releasing Plate Thread Tension Disc Thread Take-up Spring Thread Tension djusting racket Thread Releasing Pin Stopping plate O-type Ring Set Thread Finger Rubber Plug ( Φ.) Rubber Plug ( Φ.) Rubber Plug ( Φ.) Thread Take-up Lever Guard Throat Plate Sliding Plate omplete Spring Sliding Plate ed Leg Washer ack Side over omplete Seal Gasket Washer Thread Finger --
.Needle bar and thread take-up rm shaft and vertical shaft 0 0 0 --
rm nd Vertical Shafts, Needle ber Threed Take-up Parts.Needle bar and thread take-up rm shaft and vertical shaft No. Part number Name Qt. Remark 0 0 0 WF-00 T-00 T-00 T-00 T-00D WF-00 J0.0.0 T-00 T-00F T-00 T-00 T-00D T-00D T-00 T-0D T-00E T-00Ea- T-00Ea- T-00 T-00Eb- T-00Eb- WF-00 T-0P T-0 J0.0.0 T-00 T-00 T-00 T-00 T-00-0-0/ T-00 T-00 00 T-0 T-0 T-0 T-0 rm Shaft Rubber Plug Φ.~0 ollar Front ushing Middle ushing Rear ushing Oil Seal omplete alance Wheel Feed Dog Lift am Seperating Piece For am Link Vertical Shaft ever Gear Vertical Shaft evel Gear (upper) Rock Shaft ever Gear Vertical Shaft evel Gear (lower) Vertical Shaft ushing (upper) omplete Vertical Shaft ushing (lower) omplete Tread Take Lever omplete Hinge Pin Needle ar rank Set Set Thread Take-up rank Needle ar daptor Needle ar Thread Finger Needle -0-
.Feed dog lift and feed and thread looping 0 0 0 0 0 --
Feed Dog Lift nd Feed nd Thread Looping.Feed dog lift and feed and thread looping No. Part number Name Qt. Remark 0 0 0 0 0 T-0 T-00Ia T-00Ib T-00 J0.0 WF-00 J0.0. T-0 T-00 T-00 T-00 T-00 WF-00 T-00H0 T-00E T-0D T-0R T-0R T-0 T-0J T-0J T-00D T-00a T-00a T-00 WF-0 T-00 T-00 T-00 J0.0. WF-00 T-00 T-0 T-0 T-00 T-00 T-00 WF-00 J0.0. T-0 T-0 T-0H0 T-0H T-0 T-0 J0.0. T-0 J0.0.0 T-00 T-00 T-00D Feed Dog Feed Dog Support omplete Washer Eccentric Shaft Feed Dog Suppout rank Feed Shaft Stop Ring ushing ollar Feed Shaft Rear rank Link Pin Tension obbin ase omplete obbin Hook omplete Hook Rock Shatf Plug Oil Seal Front ushing Spring ollar Rear ushing Oil Tube Plunge Spring Stopper Washer Hinge Pin Feed Dog Lift Near rank Feed Dog Lift Shaft Front ushing Washer Feed Dog Lift Fork Feed Dog Lift Shaft Hook Set racket ollar Stop Ring Oil Wick --
.Feed adjustment 0 0 0 0 0 --
Feed Mechanism.Feed adjustment No. Part number Name Qt. Remark 0 0 0 0 T-00 WF-00 T-00D T-00D WF-00 T-00 T-00 J0.0.0 T-00 T-0E0 T-0E T-0 WF-00 T-00Da T-00Db T-00D T-0 T-0 T-00D T-00 T-00D WF-00 T-00D T-00D T-0 T-00 T-00D T-00E WF-00 WF-00 T-00H0 T-00EH0 T-00E T-00EH0 T-00E T-00E T-00E T-00E T-00E0 WF-00 T-00D WF-00 T-00D T-00 T-0 Link Pin Stitch Length racket ushing Shaft For Stitch Length racket Rubber Plug Set Reverse Feed Lever rank Shaft For lock Spring Reverse Feed Lever Pin Shaft O-type Ring Tension Set olt For Stitch Length O-type Rubber Ring Dial up Dial Face ushing Stop Pin SD Pring Feed am Feed Link Stitch djusting Link Pin Link Link Pin For Link Link Eccentric Shaft Stitch Length djusting rank Set Pin (left) Set Pin (right) Push Lever Spring --
.Presser foot 0 0 --
.Presser foot Foot No. Part number Name Qt. Remark T-00 Presser Foot Lift ar T-00 WF-00 Presser ar Lever am Oil Seal T-00 Knee Lifter Lever (left) omplete T-00a Lever (left ) T-00b Thread Releasing am T-00c T-00 0 T-00 Knee Lifter Drawing ar T-00 T-00 Tread Releasing Lever T-00 Knee Lifter Lever (right) T-00 Spring WF-00 onnecting Rod T-00 Pin T-00 T-0 ushing For Presser ar T-0 Presser ar 0 T-0 Presser lock For Presser ar J0.0.0 T-0 T-0 Spring T-0 T-0E Nut T-0 T-0 Presser Foot --
-- 0 0 0 0 0 0.Upper feed
Upper Feed Parts.Upper feed No. Part number Name Qt. Remark 0 0 0 0 0 T-0 T-0 T-0 T-0 J0.0.0 T-0 T-0 T-0 T-0 WF-00 T-0 T-0 T-0 T- WF-00 T- T- T-0 T- 0/0 T- T-a T- T-0 J0.0. T-c T-b T-a T- T- T- T- T-b T-0 T-0 T-0 T- T- T-00 T- -0-0/0 T-b T-c T- T-00 T- T- T- T- T-0 T- T-0 T-00 WF-00 T-00E J0.0. WF-00 WF-00 Oil Felt Nut Spring Shaft For Needle ar Motion racket Reel For Spring Link daptor Slot For Sliding lock Sliding lock Guide Rail Needle ar Motion racket Nut Washer Link For Eccentric Presser Foot Lift Eccentric Washer Rear ushing Rear rank otton Rope Oil Felt Front ushing Shaft Front rabnk Link Plate For Presser Foot Lift Nut Set lock Needle ar Motion Shaft Rear rank Nut Oil Felt otton Rope ollar Front rank Sliding lock omplete Fork Lever Pin Link Follow Presser Foot Link onnecting Pin Feed Shaft rank --
.Oil pump 0 --
Oil Pump.Oil pump No. Part number Name Qt. Remark T-00 Oil Pump T-00 T-00 T-00 Washer T-00 over For Oil Pump T-00 djusting Plate For Oil Pump T-00 Filter omplete T-00 0 T-00 Oil Pipe T- Oil Wick Set Plate omplete T-0 T-0D Oil Pipe T-0 Oil Return Pipe T-0 Oil Felt T-0 Pipe lamp -0-
.Oil reservoir and accessories 0 0 0 0 --
Oil Reservoir nd ccessories.oil reservoir and accessories No. Part number Name Qt. Remark 0 0 0. 0 WF-00 T-00 T-00 KT-00 T-00 T-00 T-00 T-00 T-000 T-00 T-00 T-00 T-00 T-00 T-00 T-00 T-00 T-00 TF-0 S000 GJX- T-0 T-0 T-0 T-00 T-00 T-00 T-00F T-0 TF-0 TF-0 TF-0 Oil Reservoir Washer Gasket Hinge Pin Spring Knee Lifter Stop racket Nut Knee Lifter Prop ar onnector ent Rod ell ell racket Pat Split Stop Ring elt Guard omplete Washer Thread Winder omplete Spool Stand omplete Oil Tank Magnet Oil Pot USHION USHION Hinge Rubber oat Parts ag obbin V-type elt Needle driver (big) driver driver (small) Wood Washer Pack --