ZBM000036SDDXLA / 1-2017 Made in the USA.5-3hp Systems Includes Drum 3-5hp Systems AXD002040A 4 Inlet AXD002030A 5 Inlet AXD002030AXL 6 Inlet Pat. # 7,282,074 Design Pat. # - D703,401 Super Dust Deputy / Super Dust Deputy XL Super Dust Deputy Deluxe 4 Owner s Manual 1.800.732.4065 www.oneida-air.com
System Start-Up Information Safety Instructions to be Strictly Followed. Read the installation and maintenance instructions as well as the recommended safety practices in this manual and your shop vacuum or dust collector s owner s manual before assembling and using the Super Dust Deputy. Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes or any hot substance! Do not vacuum, or use this Super Dust Deputy near flammable or combustible liquids, gases, or explosive dusts, such as gasoline or other fuels, lighter fluid, cleaners, oil-based paints, natural gas, hydrogen, coal dust, magnesium dust, grain dust, aluminum dust, sugar dust, flour dust or gun powder. To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials unless a HEPA filter is used. Do not use or store near hazardous materials. The Super Dust Deputy is made from static dissipating plastic. Additional grounding may be necessary in certain applications. Call Oneida with any questions. Wood dust mixtures are highly flammable and can be explosive. NEVER introduce sparks or sources of ignition into collector. 1.) Dump drum after each use. 2.) Ground system if necessary. NEVER leave wood dust in a building or vehicle. Keep fire extinguishers handy at all times. Can be used for collecting non-flammable liquids. Always read your shop vacuum or dust collector s owner s manual for safety procedures regarding the operation of your shop vacuum. Dispose of waste in a FIRE SAFE AREA. 1. WARNING / SAFETY Some dusts are highly flammable or explosive. Learn / know what you are dealing with. Follow all local, state, federal & NFPA codes and guide lines.
Troubleshooting Dust Deputy not separating well. (Only a tiny amount of dust should reach the collector.) Air leak. Check cyclone flange / drum lid / barrel. Even small leaks will affect performance. Low air volume. Vacuum filter clogged. Blockage in hose. Material swirls in cyclone and won t drop down into drum. Air leak in bottom of cyclone / drum lid or dust drum. Large, bulkier material might swirl. Restart or temporarily cut off air flow to drop material down. Air leak around top outlet. Too much torque from the outlet hose on outlet. Support hose weight to releave pressure on outlet.. Examples of Super Set-Ups These are examples of actual customer set-ups that they made using their Super Dust Deputys. As long as your dust drum is strong enough so it will not collapse, and it will make an air-tight seal, you are only limited by your imagination! Terms & Conditions Oneida Air Systems makes every effort to accurately represent our products and prices, however OAS reserves the right to make changes to products and prices at any time. As a manufacturer, OAS reserves the right to change product specifications at any time in an effort to achieve better quality products. Fire Hazards and Codes Warning! Explosion and fire hazard! Never vacuum flammable fluids or gas, oil, alcohol, solvents, etc. Do not operate near flammable fluids or gas. Never vacuum warm fluids or materials at more than 140 deg. F (60 deg. C), such as burning cigarettes, ashes, glowing coals, etc. Warning! Do not vacuum hazardous / carcinogenic dust unless a HEPA filter is installed. Always keep filter cartridge clean so the vacuum operates properly. Empty Dust Deputy waste can frequently. Never leave flammable material in your Dust Deputy or shop vacuum. Returned Goods Policy Buyer must inform O.A.S. of any shortage or damage, by so noting in writing, on the freight delivery bill prior to signing to indicate receipt of shipment. All claims, including claims covered under the limited warranty, are subject to inspection and investigation by O.A.S. O.A.S. reserves the right to inspect, investigate all returned products before Buyer s claim is settled. All products returned for a cash refund must be unused, resaleable and purchased within 30 days. There are no refunds on flex hose, custom made components or partial kit items. Kits must be returned in full (all components) for credit. There will be a 25% restocking fee applied to any returned items. Buyer must call and get an RMA (Return Authorization Number). Merchandise must be shipped to us prepaid. Limited Warranty Oneida Air Systems warrants the products manufactured by Oneida Air Systems, for a period of 90 days or more depending on the product, to the original purchaser from the date of purchase unless otherwise specified. Purchaser is responsible for returning warranty items to OAS at their expense. All parts must be returned with an OAS provided Returned Material Authorization Number (RMA#). Any shipment without an RMA will be refused. Items not manufactured by Oneida Air Systems are limited to their own manufacturer s warranties. All electrical items such as magnetic starters, remotes, sensors, pumps and accessories are limited to 90 days. Oneida Air Systems warrantees that the product will be free from defects in materials and workmanship. This warranty does not apply to defects due directly or indirectly to misuse, negligence, accidents, abuse, repairs, alterations, improper wiring or lack of maintenance. This is Oneida Air Systems sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. Oneida Air Systems does not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Oneida Air Systems liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Oneida Air Systems shall be tried in the State of New York, County of Onondaga. ONEIDA AIR SYSTEMS SHALL IN NO EVENT BE LIABLE FOR DEATH, INJURIES TO PERSONS OR PROPERTY OR FOR INCIDENTAL, AND CONTINGENT, SPECIAL, OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OF OUR PRODUCT. Before Purchasing or Installing a dust collection system the buyer is cautioned to do so in accordance with prescribed Federal, State, Local, OSHA, NFPA, and any other applicable codes or regulations relating to the type of dust(s) you are collecting. SOME TYPES OF DUST UNDER CERTAIN CONDITIONS HAVE THE POTENTIAL TO BE EXPLOSIVE. 9. Oneida Air Systems is not responsible for how the dust collector is used or installed. Dusts with deflagration or explosion risks, such as wood dust, may require additional safety equipment including but not limited to; venting, spark detection, suppression systems, back draft dampers or may require installation in an outside location or in a protected area away from personnel. The customer assumes the responsibility for contacting their insurance underwriter with regard to specific engineering controls or application requirements. (We suggest you reference NFPA 664, 654 and 68 codes for more information) Oneida Air Dust Collection Systems may not be suitable for some applications and are not designed to be used in explosive atmospheres. Oneida Air Systems equipment should only be installed and wired by a licensed electrician following all applicable local and national electrical codes. 2.
Super Deluxe 4 Kit Contents Super Dust Deputy Deluxe 4 - AXD002040A U.S. Patent #7,282,074 C1 Design Patent #D703,401 Contents: - Drum Cyclone 19 Cyclone - 15 Gal. Fiber Drum w/ Clamp - Reducer - Gasket for Drum Lid - Owner s Manual - ZBM000036SDDXLA Accessories Adapter DAO060000 Reducers DRL060500 DRL060400 DRL001205 DRL050300 6 Adapter 6 to 5 6 to 4 5 to 4 5 to 3 for 5 & 6 only May be needed to connect 6 Flex Hose to outlet. You may need reducers depending on the size of the dust ports on your machines. 15.875 4 15.875 2.375 19.125 Dust Drums SXK170601 Flex Hose DHF030000 DHF040000 DHF050000 DHF060000 17 Gal. Steel Drum Kit 3 Dia. 4 Dia. 5 Dia. 6 Dia. Heavy Duty Plastic Bags AXD600300 1.5 mil. 16 x 14 x 36 Other drums are available also. Please check the website. Sold in pre-cut lengths of 5 / 10 / 25 Other lengths may be available. Sold in packs of ten. 4 41.140 Side Braces AHX000004 Braces 19.635 3. 8.
Accessories FXK011820 HEPA Filter Retrofit Kit for Single Stage Collectors. HEPA Filter Retrofit Kit Keep your shop clean by preventing ultra-fine dust from blowing out of your single-stage bag collector and into your shop air. Add a best-in-filtration GE H12 HEPA filter to your current single stage dust collector. General Assembly Instructions for Deluxe 4 only Apply strip gasket material on perimeter of bottom of cyclone lid. (Ill. 1) Gasket Ill. 1 - Super Cartridge Filter Retrofit Kit Holes for Hanger Straps Patented Internal Silencer Quick Release Dust Pan Collector Not Included. Super Cartridge Filter 13 or 18 39 or 62 Catches the micro-fine dust. Small footprint. Quick clean out dust pan. FXK010039 FXK010000 Filter Media ASHRAE Tested Included 39 L x 13 D / 7 Inlet / 95 Sq. Ft. 62 L x 18 D / 8 Inlet / 130 Sq. Ft. Holes for Hanger Straps 7 or 8 High Efficiency Axtar Spun-Bonded Media Teflon-Like Coating to Facilitate Dust Cake Release Filter Media Captures 99.9% of Test Material from 0.2-2 Microns @ 11 FPM / Accredited, Independent Lab Tested High Efficiency Filter Cartridge / Dust Drum Filter Cap with Holes for Hanging / Hardware Place cyclone on drum. (Ill. 2) Place clamp in place and snap closed. Install reducer in top outlet hole. Firmly insert reducer in place. (Sealant may be required - Not Included)Install your 4 inch flex hoses from your machines to the inlet and from the cyclone outlet to your dust collector using a suitable hose clamp. For best performance, keep hoses as straight and as short as practical. Empty your drum when 2/3 full, check often. Any air leaks in drum or seal between lid and drum will diminish separation performance. Never allow sparks or material that may possibly be smouldering or burning to enter the system. Read and observe all safety instructions stated elsewhere in this manual as well as for your dust collector and machinery generating dust. Reducer Cyclone Clamp Ill. 2 * Do not let the hose weight over torque the top outlet. Small leaks may occur. Optional May be required for installation: Elbows / Reducers Flex Hose / Duct Hanger / Pipe Hangers 7. *Oneida reserves the right to change or modify specs and system appearance without notice. Actual system appearance may vary. 4.
Super Kit Contents U.S. Patent #7,282,074 C1 Design Patent #D703,401 Contents: - Drum Cyclone 16 Cyclone - VXC160001A (1) or - Drum Cyclone 18 Cyclone - VXC180001A (1) - Roll of Gasket - 24 x 1/4 x 1/4 RGZ250250 (1) - Bolts 1/4-20 x 3/4 Hex Head - AFS015920 (6) - Washer Flat 1/4 - AFW025000 (12) - Whiz Lock Nut 1/4 - AFT000005 (6) - Owner s Manual - ZBM000036SDDXLA Dimensions AXD002030A Super Dust Deputy - AXD002030A / Super Dust Deputy XL - AXD002030AXL General Assembly Instructions 1. Apply gasket around the flange bottom of the cyclone, making sure that the gasket goes inside the bolt holes and around the fin indentions for the regular Super Dust Deputy (Fig. 1) and outside the bolt holes and around the fin indentions for the XL version (Fig. 2). An air tight seal is extremely important for good dust collection. Make sure ends of gasket butt together and there are no gaps. 2. Turn cyclone upside-down and place it on the floor or other flat surface. Turn drum lid over and align bolt holes in lid with bolt holes in cyclone base. Put bolt through washer, then put bolt and washer through lid from the underside of lid, one more washer for under the nut and attach with whiz nut. Tighten nut and repeat with all six bolts. Thoroughly tighten hardware to eliminate air leaks. (Fig.4A & 4B) 3. Put cyclone and lid on top of optional dust drum then attach and seal with clamp ring. (Fig. 3) 4. When you attach the hose from your tool to the inlet, you may need to use a reducer depending on the size of your tools dust colllection outlet. 5. Attach 6 hose to the Super Dust Deputy s or the XL s top outlet with a hose clamp, then connect the other end to your collectors fan blower as shown in the diagram below.(fig. 5) Do not let the hose weight over torque the top outlet. Small leaks may occur. 6. Make sure there are no air leaks at the connections. Make sure to check your dust drum frequently so you do not overfill it. 6. for 5 & 6 only 1. 2. 3. Regular AXD002030AXL 17.9 7. You may need to use an adapter to connect the 6 flex hose to outlet. See accessories page. (Fig.6) #DAO060000 19.1 37.5 5. XL 4A. 5. 4B. 6.