Le Belle Mura Decorative Plaster line was created exclusively by and for Atova International. In keeping with Italian tradition, we created a pure line of lime plasters which encompasses the very best materials with old world craftsmanship. Fit for interior and exterior applications, Le Belle Mura meets the best expectations in wall decoration. Its unique effects are dominated by light, color hues, and nuances. In keeping with simplicity, we offer over 80 available tints, which can be achieved using only one toner. As an alternative, Atova has introduced our new Global Tinting System which enables you to choose a color from other than our color chart to meet the needs of our customers. Le Belle Mura has been designed for the professional without compromising attention to detail.
Stucco Marmorino Decorative lime based Venetian Plasters Stucco Marmorino it is a multi-purpose, highly prestigious, decorative plaster for contemporary and classic decoration. Marmorino, is a trowel applied, paste plaster based on calcium oxide for interior and exterior use. It can be finished using multiple techniques for a variety of matt, satin, and glossy final effects. Due to its outstanding hardness, transpirability, and gloss, it is a solution that is becoming more and more popular not only for its decorativeness, but rather for its convenience. Stucco Marmorino Superior marble looking lime plaster for glossy translucent finishes typical of the Renaissance period. Surface preparation: It is recommended to apply over other natural lime surfaces, but it can also be applied after one coat of Primer S, on plaster, plaster by-products, or old paint, if surface is not cracked or peeling. Application: Apply first coat of Stucco Marmorino with a stainless steel trowel. When the first coat has dried, spread a second coat of product in the same manner as the first coat. Allow second coat to dry and then apply small spots of product and then take them away ( put and remove technique) (Photo No. 2). As the product is drying, compress and polish until the desired result is obtained (Photo No. 3) Available in: 1Quart, 1 Gallon, 2 Gallons, 4 Gallon pails. Spread rate: 20 to 30 Sq. ft. per quart. Stucco Marmorino Neutro - Used to obtain darker tones. Stucco Marmorino Classico- Used to obtain lighter tones. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service.
Stucco Veneziano Decorative Venetian Plasters Stucco Veneziano or Venetian Plaster is perfect for both modern and classic ambiences, both residential and commercial settings, and virtually any interior space. A classic finish that lends prestige to both classic and contemporary settings, Stucco Veneziano is a "Venetian Type Plaster" most often characterized by it's smooth, polished, or can be textured. marble like surface. Stucco Veneziano A classic polished finish for contemporary or Old World charm. Stucco Veneziano is a "Venetian Type Plaster" most often characterized by it's smooth, polished, and textured finish. Surface preparation: Recommended to be applied over new plaster, drywall, or paint, with the application of one coat of Primer S. Application: Spread a coat of Stucco Veneziano with a stainless steel trowel over the surface. (Photo No. 1). When the first coat has dried, spread a second coat of product same as first coat. When second coat is dry, apply little spots of product and then take them away ( put and remove technique). (Photo No. 2) Once the product is dry, about 1-3 hours, lightly sand and polish until the desired result is obtained. (Photo No. 3) Available in: 1 Quart, 1 Gallon, 2 Gallons, & 4 Gallon pails. Spread rate: 12 to 26 Sq. ft. per quart. Stucco Veneziano Neutro Used to obtain darker tones. Stucco Veneziano Classico Used to obtain lighter tones. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com Natural products with low VOC. Resist aggression by moulds and bacteria
Stucco Nahir Velvet Effect Decorative Plasters Decorative System which was created from the inspirations of the enhancing place that are still to be found in the wonderful Sicilian island, the land of many colors, where the Byzantines styles, Arabs and Normans mix almost naturally with the Landscape of the island. This is where the idea was found to create this new decorative effect. An ethnic style, with the magic touch of Italian Style. This decorative system has a very special Stucco which is easy to model and this allows you to create endless effects. With the application of Velatura Classic or Pearl on top it seems to create transparency, deepness and a unique and fascinating dark light contrast. Nahir Stucco: Innovative decorative finish with extraordinary beauty and easy application, which is used in Linear,Crackle, & Nahir effects. Application: Apply on a smooth and well-cohesive wall or plasterboard, 1 coat of primer S with a shorthaired roller (photo n. 1). After at least 8 hours, spread 1 coat about 2 to 3 mm of Nahir with a plastic trowel, making sure to cover the entire surface evenly (photo n. 2). It is advisable to apply Nahir in strips of about 20 to 30 inches long the entire wall. Immediately follow with the special Linear Effect Trowel (photo n. 3), finish Nahir horizontally, vertically or combination (depending on the effect desired). When finished (after at least 24 hours), apply Veletura with a paint brush following the direction of the lines (photo n. 4) and remove the excess product with a sponge trowel tool (photo n. 5). Nahir base: sizes: 1Quart, 1 Gallon, 2 Gallons, 4 Gallons Pails Spread Rate: 20-30 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com
Stucco Travertino New Concept The Decorative System Travertino new concept discovers and values the aristocratic effect of the famous Italian Marble with an absolutely innovative style. It a wall finish that allows you to obtain tones, colors and a sensation which up to now was not obtainable with Travertino. The elegant aspect of extraordinary beauty renders Travertino ideally for high prestige surroundings. Travertino The Travertino Decorative Plaster allows one to discover the ancient effect of Italian marble with an absolutely innovative style. It is a wall finish that allows you to obtain tones, colors, and finishes unlike any other. Travertino is suitable for high end and casual wall finishes. Surface preparation: Apply one coat of Primer RV, which adheres well on cement, ceramic and hard wall board (Photo No. 1) with a paint brush/roller on a perfectly level, smooth and clean surface. Application: Allow Primer RV to dry for at least 24 hours. Apply the first coat of Travertino with a stainless steel trowel over the entire surface evenly. (Photo No. 2). Before it is completely dry, apply the second coat of Travertino (Photo No. 3) and immediately go over the surface with a sponge roller in order to create a crisping effect (Photo No. 4). Then, with a stainless steel trowel, create the smooth part of finish, as clearly illustrated (Photo No. 5). Allow to dry for about 5 minutes and then with a flat trowel, go over the entire surface, scratching in horizontal directions in order to obtain the Travertino finish desired (Photo No. 6). When the entire surface has been completed, go back over it, pressing it with a perfectly clean stainless trowel in order to shine only the smooth parts of the surface (Photo No. 7). Optional Wax Application: After 24 hours, apply 1 coat of Arthe Wax Naturale, with a sponge or a sponge float (Photo No. 8). Available in: 1Quart, 1 Gallon, 2 Gallons, & 4 Gallon pails Spread rate: 13-15 Sq. ft. per quart This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 ww.paintandplasters.com Natural products with low VOC. Resist aggression by moulds and bacteria
Stucco Intonachino Decorative Stucco Lime Stucco Intonaco is a through colored decorative lime stucco for indoor/outdoor use. It has a granular finish, and is based on well seasoned air binders, mineral pigments, and selected extenders of various grain sizes. Intonaco has a high transpiration power and excellent adhesion rate to the substrate, which enhances the user friendly experience. The product does not crack and fights the formation of mold inside buildings. It drastically reduces blooming, due to a limited presence of mineral salt inside the stucco. Overall, it is a professional decorative stucco with a wide range of uses that provides excellent features other than its physical appearance. Lime Stucco Intonachino is a decorative lime stucco for indoor/outdoor use. It s granular formula makes for a variety of different finishes simulately effects of natural stone which vary greatly from its natural appearance. Surface preparation: Before applying this product, wet the surface, which must be suitably cured. Spread the product evenly over the surface using stainless steel trowels. For best results, it is advised to apply Intonachino in two coats. The first must be spread with a tight. finish. When dry, wet the surface again and apply the finishing coat moving the trowels to provide an antique effect. It is essential to use a two-coat application cycle for surfaces that have been patched or grooved, as such defects may give rise to differing levels of absorption, spoiling the final appearance of the product. Top coat velatura water base glaze. Avaiable in: 1 Quart and 14 Liters Spread rate: 6 to 11 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com Natural products with low VOC. Resist aggression by moulds and bacteria
Velatura Rustica Silossanica Ideal for old world style interiors or exteriors. Feel antique looking of velatura silossanica, characterized by a semitransparent quality and typical chiaroscuro effect of the velatura. Velatura Classic A simple application system, where natural light to dark effects appear over the surface. Ideal for decorating the interior wall surface of homes and buildings that aim to recreate a classic antique feel. Surface preparation: Sand, dust, and level any imperfection using joint compound. Apply one coat of Universal Fixative which should be diluted in water at a ratio of between 1:R up to 1:10; depending on the absorption of the surface to be applied. Spread the product consistently using a flat paint brush (Photo No. 2) or a sponge over the surface using a circular motion. (Photo No.3). Available in: 1 Quart and 1 Gallon pails. Velatura spread rate: 70-100 Sq. ft. per quart. Velature Rustica A simple application system where the natural light to dark effects appear over the surface. Ideal for decorative finishes over both interior and exterior homes and buildings that aim to achieve a classic antique look and feel. Surface preparation: Maybe applied over any rough or textured plaster surface or directly over brick after a coat of Primer RV. Application: Apply one coat of Velatura Rustico over the surface with a flat paint brush. Apply a second coat in the same manner and follow through with a sponge trowel to obtain a uniform appearance. Available in: 1 Quart and 1 Gallon pails. Spread rate: 70-100 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com
Stucco Marmo Antico Grainy slaked lime based decorative stucco Superior, marble-looking lime plaster with grainy slaked lime typical of Modern houses. The Decorative System Marmo plaster concept discovers and values the aristocratic effect of the famous Italian Marble with an absolutely innovative style. Stucco Marmo Antico Italian marble plaster with an innovative style for contemporary finishes. This product is a natural decorative plaster, formulated according to the original formulas with the features of new technology. It allows you to obtain a marble-like finishing with a spotted semi-flat effect. Surface preparation: Apply a coat of Primer RV over the entire surface evenly with a brush or roller. (Photo No.1) If surface is primed with Primer RV, you may apply over existing plaster, cement, and plaster board. Application: Apply a coat of Marmo Antico with a stainless steel trowel to level the surface. (Photo No. 2) Apply a second coat of Marmo Antico to obtain a perfectly smooth surface. As the product is drying, compress slightly and begin to polish with a clean stainless steel trowel until the desired effect is obtained. (Photo No. 3) Available in: 1 Quart, 1 Gallon, 2 Gallons, & 4 Gallon pails. Spread rate: 11-15 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/ or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com Natural products with low VOC. Resist aggression by moulds and bacteria
Stucco Coccio Pesto Stucco decorativo al Cocciopesto e grassello di calce Stucco decorative lime plaster with cocciopesto terracotta grains, combining the sfiammature effect typical of the cocciopesto and the lime putty translucent quality. Cocciopesto Decorative lime plaster with terracotta grains which combine to create the faded effect with the translucent quality of natural lime plasters. Cocciopesto is naturally low in VOCs and is mold resistant. Surface preparation: It is recommended to apply over other natural lime surfaces, but it can also be applied after one coat of Primer S, on plaster, plaster by-products, or old paint, if surface is not cracked or peeling. Application: Spread a coat of Cocciopesto with a stainless steel trowel so as to level the surface (Photo No. 2). Apply a second coat of Cocciopesto so as to obtain a perfectly smooth surface. Once the product is almost dry, compress slightly and polish with a clean stainless steel trowel so as to allow the shades deriving from the crushing of the Cocciopesto grains to appear. (Photo No. 3). Cocciopesto: Available in: 1Quart, 1Gallon, 2 Gallons, & 4 Gallons pails. Spread rate: 12 to 15 Sq. ft. per quart (2 coats). This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com Natural products with low VOC. Resist aggression by moulds and bacteria
Stucco Marmo Carrara Semi Glossy Lime Venetian Plaster Carrara Stucco Marmo Carrara Semi Glossy Lime Venetian Plaster for interior wall finishes. Carrara is easy to apply, enviornmentally friendly, VOC free. Surface preparation: Apply a coat of Fondo Fine primer to any surface such as, existing plaster, plasterboard, drywall, or paint. Application: Apply first coat of Carrara untinted evenly to the surface with a stainless steel trowel. Apply second coat wet on wet directly over first coat applying pressure so that the grains appear on the surface. While second coat is drying, begin to polish by applying pressure to the surface with the trowel. Available in: 1Quart, 1 Gallon, 2 Gallons, & 4 Gallon pails. Spread rate: 11-19 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/ or call our technical service. For more information, please call: 1-866-452-9982 9982 www.paintandplasters.com RFACE PRELIMINARY TREATMENTS
Stucco Marmo Puntinato Black Dotted Lime Venetian Plaster Puntinato Stucco Marmo Putinato Black dotted lime Venetian Plaster for decorative interior wall finishes. Putinato is an easy to apply environmentally friendly, VOC free slaked lime plaster. Surface preparation: Apply a coat of Fondo Fine primer to the surface such as existing plaster, plasterboard, drywall, and paint. Application: Apply a first coat of Putinato with a stainless steel trowel or spatula evenly to create a flat surface. (Photo No. 1) When the first coat is dry, apply a second coat on a 45 degree angle to allow black dots to appear. Allow second coat to dry and apply a third coat if so desired. (Photo No. 2) Once third coat is dry, begin to polish while surface is in the drying process. (Photo No. 3) Available in: 1Quart 1 Gallon, 2 Gallons, & 4 Gallons pails. Spread rate: 12-15 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com RFACE PRELIMINARY TREATMENTS
Stucco Caravaggio Velvet Effect Decorative Plasters Caravaggio combines the precious features of the Venetian stucco with the original elegance, softness and light effects typical of the ancient wall fabrics, used in the Renaissance. Caravaggio allows you to obtain some extraordinary results (never seen before with other traditional paints) by exploiting the decorative abilities and creativity of the painter who can create original nuances with very different applications, suitable for all kinds environments. Caravaggio Silver Effect Broccato Caravaggio Gold Effect Damascato Caravaggio Plaster combines the velvet effect of Venetian plaster with the original elegance, softness, and light effects typical of wall fabric. Caravaggio allows you to create a unique look and effect with every stroke and twist of the trowel. Although, Caravaggio look can be extremely elegant, it is suitable for all types of interior wall environments. Surface preparation: Sand, dust, and level any imperfections with joint compound. Apply a coat Universal Fixative diluted in water between 1:R to 10:R. evenly to the entire surface with a brush or roller. Allow to dry for four hours. Application: Spatolato Effect Apply the first coat of product about 0.5 to 1 mm in thickness with an Atova PVC spatula. Allow it to dry for about 6-8 hours. Apply the second coat in small areas about one square meter at a time and immediately go back over the applied surface gently using the PVC trowel/spatula in different directions and continue over entire surface in the same manner. Available in: 1 lt. and 4 lt. pails. Spread rate: 40-50 sq. ft. per liter This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com Natural product with low VOC
Stucco Encausto Fiorentino Wonderfull Marmorino Effects Resulting from the ancient synergy of particular marble chips with lime putty, for elegant and orginal marble-looking opaque and semi-opaque effects. Encausto Fiorentino An elegant marble finish creating opaque effects. Surface preparation: Can be applied on both interior/exterior surfaces. It is recommended to apply over other natural lime surfaces, but it can also be applied after one coat of Primer RV, on plaster, plaster by-products, or old paint, if surface is not cracked or peeling. Application: Spread a coat of Encausto Fiorentino with a stainless steel trowel to level the surface. (Photo No. 1). Apply a second coat of Encausto Fiorentino as to obtain a perfectly smooth surface (Photo No. 2). Once the product is dry, compress slightly and polish with a clean stainless steel trowel until the desired result is obtained (Photo No. 3). Encausto Fiorentino: Available in: 1Quart, 1Gallon, 2 Gallons, & 4 Gallons pails Spread rate: 12 to 15 Sq. ft. per quart. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/ or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com Natural products with low VOC. Resist aggression by moulds and bacteria
Pittura Decorativa alla Calce Natural mineral lime paint REATMENTS Pittura Decorativa alla Calce- Lime Paint A mineral paint based on slaked lime putty finely filtered and seasoned for at least 6 months. It is environmental friendly and VOC free. Easy to apply, it is naturally resistant against mold and bacteria. Pittura alla Calce lime paint is suitable for interior and exterior wall surfaces. Lime Paint is used to create aged effects over existing plaster or new plasters from Le Belle Mura. Surface preparation: It is necessary to prime all surfaces accordingly. Apply a coat of Fondo Fine over the surface. Apply with a brush or roller evenly over the surface. Application: Apply Lime Paint with a sponge, roller, brush, or sponge trowel in a fashion to create the desired effect. Lime Paint may be applied in one, two, or three coats depending on desired effect. Allow to dry in between coats. Available in: 1Quart, 1Gallon, 2 Gallons, & 4 Gallon pails. Spread rate: 35-50 Sq. ft per quart This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/ or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com
Crocodile Finish Atova's "Crocodile Finish" is the first of its kind. In keeping with Atova tradition, we are now offering the newest and hottest finish for wall decoration. Created by Atova, this tool was developed to consistently create the "skin" look so highly sought after. This easy to use tool, together with Atova's new formulated Caravaggio" plaster product can consistently create a perfect alligator or crocodile skin effect in a large range of colors. Caravaggio's graceful illusion reflects light and color like no other of its kind. It is a fine microplaster with an amazing coverage rate. Manufactured in two bases, Caravaggio comes as either a gold or silver base. The gold base doesn't require tinting, as it is designed with fine gold pigments and mica, enabling a rich and sophisticated gold finish. The silver or gold base can be tinted with universal pigment, or with special toners available from Atova. A display of color and light, Caravaggio adds depth and mystery to surfaces. Its thin consistency enables better coverage and light application methods. 1. Tint the base coat plaster with the same quantity of color selected to color Caravaggio gold or silver. 2. Apply one or more coats of base coat plaster until you obtain a smooth surface. 3. Before base coat plaster sets, use tool to stamp out Crocodile effect. 4. Once the surface is dry, remove high points and edges with a scrapper and sand surface with 120-150 grit sand paper. 5. Resand with 320 or 400 grit sand paper after sand again with 600 grit sand paper to smooth and polish the surface. 6. Clean the surface to remove access dust and polish with stainless steel trowel. 7. Apply a layer of Caravaggio using a suitable plastic trowel pulled tightly. 8. Once dried, you have the option to wax the surface using a brush or cotton cloth. This Information is based on our best technical and practical knowledge. However, since the actual conditions in which the products are used beyond our direct control, we provide no guarantee as to effectiveness of the advice and suggestions contained herein. If in doubt, it is advisable to conduct preliminary tests and/or call our technical service. For more information, please call: 1-866-452-9982 www.paintandplasters.com
Cera Naturale/ Natural Wax Natural bees wax specially formulated for lime plaster. Water base and naturally 100% and 0 VOC free. Cera Naturale is used to increase the shine and durability of lime and decorative plasters on interior wall surfaces only. Application: Allow plaster to dry for up to 48 hours before applying wax. Mix wax carefully and spread with a soft cloth or non-abrasive sponge. Wait one to two hours and proceed to burnish with a cloth or mechanical buffer. Storage: Cera Naturale maintains its properties for a period of 12 months if protected from excessive heat and cold. The storage temperature must be between 41 and 86 degrees F. Protect from frost. Safety guidelines: Avoid contact with skin and eyes. If contact occurs, rinse thoroughly with water. For more information consult the safety sheet or a physician. Available in: 1 Quart, 1 Gallon, 2 Gallon pails. Spread rate: 200-300 Sq. ft. per quart. Arthe Wax Naturale Natural transparent protective wax specifically formulated for both synthetic and lime plasters. Arthe Wax Naturale increases the level of shine and makes the surface water repellent and stain resistant. Has the ability to enhance the final color of plaster when dry. Application: Allow plaster to dry for up to 48 hours before applying wax. Apply wax directly over the polished stucco/plaster with a soft cloth, stainless steel spatula, or trowel. Apply wax at room temperature. Available in: 1 Quart or 1 Gallon pails. Spread rate: 200-250 Sq. ft. per quart. "Shine" Wax An oil based wax for Venetian Plaster. Capable of penetrating the surface and sealing it from unwanted stains, fingerprints, or spills. Ideal for bathrooms, kitchens, and other high traffic areas, Shine wax can darker the finishes plaster effect by 30% and an high shine and durable finish. Application: Apply shine wax with a stainless steel trowel, mechanical buffer, or a soft cotton cloth. Allow Venetian Plaster to dry 48-72 hours prior to applying wax. Available in: 1 Quart Spread Rate: 200-250 Sq. ft. per quart. Matte Wax Water based wax and protective coating for Venetian and all types of decorative plasters. Matte wax can penetrate the plaster and seal the surface for superior protection. Ideal for use in bathrooms, kitchens, and other high traffic areas. Created to enhance the shine and conceal minor wall surface imperfections. Application: Apply Matte wax with a stainless steel trowel or cotton cloth. Allow Venetian Plaster to dry 24-48 hours prior to applying Matte Wax. Available in: 1 Quart and 1 Gallon Pails. Spread Rate: 200 Sq. ft. per quart
Primer S "Primer S" is an acrylic resin-based product in emulsion containing marble grains. It is a smooth effect primer particularly suitable to aid in the adhesion of plasters on smooth supports with low absorption, such as concrete, cellular cement, plasterboard, or plaster. It is in fact applied as a binding element on those difficult supports where common plasters do not easily adhere. Composition: Acrylic emulsion, special surface-active agents, quartz grains, other additives. Application: Dilute the product with 20-35% of water and apply with a paintbrush or roller. Stir the product at regular intervals. Technical data: Dilution: 20% -35% with water Drying time: 30 minutes to the touch completely dry in 24 hours at 68 F. Apply with a paintbrush, roller, may be sprayed. Shelf life: 36 months if unopened Available in: 1Quart, 1 Gallon, 2 Gallons, 4 Gallon pails. Spread rate: 71 to 82 Sq. ft. per quart. Primer RV "Primer RV" is an acrylic resin-based product in emulsion containing marble grains. It is rough effect primer, particularly suitable to aid in the adhesion of plasters on smooth supports with low absorption, such as concrete, cellular cement, plasterboard, plaster, or ceramic tiles. Composition: Acrylic emulsion, special surface-active agents, quartz grains, other additives. Application: Dilute the product with 30%-45% of water and apply with a paintbrush or roller. Stir the product at regular intervals. Technical data: Dilution: 30% - 45% with water Drying time: 30 minutes to the touch completely dry in 24 hours at 68 F. Application: paintbrush, roller, spray Shelf life: 36 months if unopened Available in: 1Quart, 1 Gallon, 2 Gallons, 4 Gallon pails. Spread rate: 71 to 82 Sq. ft. per quart. Fondo Fine Fondo Fine Primer is a special clinging primer for lime based plasters. Based on acrylic polymers and natural fine quartz, it has a low VOC content. Its function is meant to create an accurate amount of product disbursed on the first coat. Fondo Fine is made to adhere to all surface types and can be applied both for interior/ exterior applications Application: Apply with a brush or roller evenly over the surface. Available in: 1 Quart, 1 Gallon, 2 Gallons, and 4 Gallon Pails. Spread Rate: - 7080 Sq. ft. per quart.
Official Distributor for Pavan Tools 866-452-9982
PAVAN produces the widest range of spatulas and trowels in the market today. The variety of its range can satisfy all professional uses. Handles are made with selected types of wood (beech, acacia), to obtain better resistance. Tempered steel blade of viariable thicknesses. Flexibility and toughness are guaranteed in each job for best results. Ancora trade-mark by Pavan, Leader for 140 years in the production of professional high quality tools, has realized this indispensable case to protect, as a coffer, our jewels that professional users hold in their hands in the ancient art of application of Marmorino and Venetian Stucco. You can personalize the kit at your convenience and tools are available either with wood handle or with soft grip Sintesi handle. Complete Tool Kit for Decorative Finishes. 18 tools included $ 479.95 Art. 984/1 140 mm Stainless steel round filling trowel. Art. 980/I 80 mm Stainless Steel filling trowel Swiss model Synthetic fiber to clean blades Art. 501/1 100mm Filing Spatula Art 613 80mm Tempered steel scraper Art 536 80mm 100mm Ultra Flexible Spatulas Art. 501/IS 40mm, 60mm, 80mm, 100mm Stainless steel plastering spatula to spread and smooth. Art. 824/1 120x280mm 100x240mm 80x200mm Superior INOXStainless steel trowel plastering for venetian plaster and marmorino Art 504/IS 100mm, 120mm Stainless steel putty spatula Art 840/ 120x280mm 240x100mm Stainless steel plastering trowels to spread and smooth
PAVAN produces the widest range of spatulas in the market today. The variety of its range can satisfy all professional uses. Handles are made with selected types of wood (beech, acacia), to obtain better resistance. Tempered steel blade of viariable thicknesses. Flexibility and toughness are guaranteed in each job. Atova - Venetian Plasters Spatulas - Rounded Edges and radius blade Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula Sintesi handle 501/IS 40 mm 1.6 in $ 12.95 501/IS 60 mm 2.4 in $ 13.95 501/IS 80 mm 3.2 in $ 14.95 501/IS 100 mm 3.9 in $ 16.95 501/IS 120 mm 4.7 in $ 19.95 Atova - Venetian Plasters Spatulas - Straight Edges Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula Sinthesi handle 501/S 20 mm 0.9 in $ 4.95 501/S 30 mm 1.2 in $ 4.95 Atova - Venetian Plasters Spatulas - Straight Edges Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula wood handle 501/I 40 mm 3.6 in $ 11.95 501/I 60 mm 3.9 in $ 12.95 501/I 80 mm 4.3 in $ 13.95 501/I 120 mm 4.7 in $ 15.95 Atova - Venetian Plasters Spatulas - Rounded Edges and radius blades Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula wood handle 503 20 mm 0.8 in $ 13.95 503 40 mm 1.6 in $ 14.95 503 60 mm 2.4 in $ 16.95 503 80 mm 3.2 in $ 18.95 503 100 mm 3.9 in $ 21.95 503 120 mm 4.7 in $ 25.95 503 140 mm 5.2 in $ 26.95
PAVAN produces the widest range of spatulas in the market today. The variety of its range can satisfy all professional uses. Handles are made with selected types of wood (beech, acacia), to obtain better resistance. Tempered steel blade of viariable thicknesses. Flexibility and toughness are guaranteed in each job. Atova - Venetian Plasters Spatulas - Rounded Edges and radius blade,extra flexible Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula plastic handle 504/IS 80 mm 3.2 in $ 14.95 504/IS 100 mm 3.9 in $ 16.95 504/IS 120 mm 4.7 in $ 21.95 504/IS 150 mm 5.5 in $ 24.95 Atova - Venetian Plasters Spatulas - Straight Edges Blades steel, hand made tools made in Italy by Pavan Spatula plastic handle 504 20 mm 0.8 in $ 5.95 504 30 mm 1.2 in $ 5.95 504 40 mm 1.8 in $ 5.95 504 50 mm 2.4 in $ 6.95 504 60 mm 2.5 in $ 6.95 504 70 mm 2.8 in $ 6.95 504 80 mm 3.2 in $ 7.95 504 90 mm 3.5 in $ 8.95 504 100 mm 3.9 in $ 9.95 504 120 mm 4.7 in $ 9.95 504 130 mm 4.9 in $ 10.95 504 140 mm 5.2 in $ 11.95 504 150 mm 5.7 in $ 12.95 New Exclusive for Atova Atova -Rounded Edges Spatula - Sicodur blade Spatulas are made of 100% stainless steel. Soft Spatulas provide excellent flexability while keeping uniform composure. Wood handle. 541/I 80 mm 3.2 in $ 5.95 541/I 100 mm 3.9 in $ 6.25 541/I 140 mm 5.2 in $ 6.95
PAVAN produces the widest range of spatulas in the market today. The variety of its range can satisfy all professional uses. Handles are made with selected types of wood (beech, acacia), to obtain better resistance. Tempered steel blade of viariable thicknesses. Flexibility and toughness are guaranteed in each job for best results. Atova - Venetian Plasters Spatulas - Toothed scraper or spreader 0.1 mm Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula flat wood handle,2.5 mm thick, 541/I 80 mm 3.2 in $ 5.95 541/I 100 mm 3.9 in $ 6.25 541/I 120 mm 4.7 in $ 6.95 541/I 150 mm 5.6 in $ 7.95 Atova - Venetian Plasters Spatulas - Toothed scraper or spreader 0.5 mm Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula wood handle, 541/ID 100 mm 4.7 in $ 6.95 541ID 140 mm 5.6 in $ 7.95 Atova - Venetian Plasters Spatulas - Rounded Edges Japanese Knife Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula Sintesi handle 537/I 90 mm 3.6 in $ 6.25 537/I 100 mm 3.9 in $ 6.95 537/I 110 mm 4.3 in $ 7.95 537/I 120 mm 4.7 in $ 8.95
Special steel welded trowels. Top ergonomics for the widest variety of jobs. Flexibility and toughness guaranteed under all working conditions. Assembly by welding is tested rigorously for load bearing and xrayed for perfect joining. An exclusive lip process ensure the perfect apllication and the quality of the final polishing operation. Atova - Venetian Plasters Trowels - Rounded Edges Trapezoid Blade Thickness 0.5 mm - Flexible Inox Stainless Steel Softer Touch Blade Thickness 0.6 mm - Flexible Inox Stainless Steel Blades INOX Stainless steel, hand made tools made in Italy by Pavan Trowels sinthesi handle 824/I 200x80x0.5 mm 7.9 x 3.2 in $ 49.95 824/I 240x100x0.5 mm 9.5 x 3.9 in $ 52.95 824/I 200x100x0.5 mm 11 x 4.5 in $ 49.95 824/I 200x80x0.6 mm 7.9 x 3.2 in $ 49.95 824/I 240x100x0.6 mm 9.5 x 3.9 in $ 52.95 824/I 280x120x0.6 mm 11 x 4.5 in $ 55.95 Atova - Venetian Plasters Trowels - Rounded Edges Flexible - Trapezoid Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula wood handle 825/I 200x80 mm 7.9 x 3.2 in $ 33.95 825/I 240x100 mm 9.5 x 3.9 in $ 37.95 825/I 280x120 mm 11 x 4.5 in $ 39.95 Atova - Venetian Plasters Spatulas - Rounded Edges Flexible German Model Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula wood handle 803/I 200x80 mm 7.9 x 3.2 in $ 29.95 803/I 240x100 mm 9.5 x 3.9 in $ 33.95 Atova - Venetian Plasters Spatulas - Straight Edges Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula Sintesi handle 845/IS 280x120 mm 11 x 4.5 in $ 26.95
Special steel welded trowels. Top ergonomics for the widest variet of jobs. Flexibility and toughness guaranteed under all working conditions. Assembly by welding is tested rigorously for load bearing and x-rayed for perfect joining. An exclusive lip process ensure the perfect apllication and the quality of the final polishing Atova - Venetian Plasters Spatulas - Straight Edges Blades INOX Stainless steel, hand made tools made in Italy by Pavan Spatula Sintesi handle 840/I $ 27.95 240x100 mm 9.5 x 3.9 in Atova - Plastic Spatulas for Decorative Finishes - Rounded Edges Blades Plastic, hand made tools made in Italy by Pavan Plastic trowels Plastic Handle 817/PV 240x100 mm 9.5 x 3.9 in $ 8.95 817/PV 280x120 mm 11 x 4.5 in $ 9.95 Atova - Plastic Spatulas for Decorative Finishes - Straight Edges Blades plastic, hand made tools made in Italy by Pavan Plastic trowels Sintesi Handle 817/RS $ 22.95 240x100 mm 9.5 x 3.9 in Atova - Plastic Spatulas for Decorative Finishes - Straight Edges Blades plastic, hand made tools made in Italy by Pavan Plastic trowels plastic handle 817/P $ 15.95 280x130 mm 11 x 4.9 in
Welded or riveted special steel finishing trowels. In the sintesi model the coating of the handles is of soft and vibration resistant material. Thanks to its ergonomic shapes a highly comfortable grip is possible. To reset the grip we recommended to clean the handle, after removing the exceeding material, with a standart solvent. Atova - Sponge trowels for Decorative Finishes Light Textures Rubber thickness: 19 mm, hand made tools made in Italy by Pavan Orange rubber trowel, wood handle 820/1 215 x 135 mm 8.3 x 5.1 in $ 12.95 820/2 240 x 100mm 9.5 x 3.9 in $ 11.95 820/3 400 x 72 mm 15.6 x 2.9 in $ 14.95 820/6 135 x 135 mm 5.1 x 5.1 in $ 10.95 Atova - Sponge trowels for Decorative Finishes Light Textures Rubber thickness: 15 mm, hand made tools made in Italy by Pavan Orange rubber trowel, wood handle 820/1-1S 215 x 135 mm 8.3 x 5.1 in $ 12.95 820/2-1S 240 x 100 mm 9.5 x 3.9 in $ 11.95 Atova - Sponge trowels for Decorative Finishes Light Textures Harder Rubber thickness: 14 mm, hand made tools made in Italy by Pavan Blue rubber trowel, wood handle 819/1 215 x 135 mm 8.3 x 5.1 in $ 12.95 819/2 240 x 100 mm 9.5 x 3.9 in $ 11.95 Atova - Sponge trowels for Decorative Finishes Large Textures Rubber thickness: 15 mm, hand made tools made in Italy by Pavan Orange rubber trowel, Plastic handle 882/1 215 x 135 mm 8.3 x 5.1 in $ 12.95 882/2 240 x 100 mm 9.5 x 3.9 in $ 11.95
SCRAPERS A wide range of tools specifically made for each specific use. All blades are made of tempered stell and are rectified for best performance. The innovative aluminum planes for plaster with oval section handles which are made of a special alloy offer a firm and ergonomic grip. Top toughness and rigidity and a lightness which was never reached before. Atova - Venetian Plasters Spatulas - Straight Edges Blades INOX Stainless steel, hand made tools made in Italy by Pavan Plastering scraper with replaceable abrasive cloth. Wood handle 621 gr. 60 $ 34.95 330 x 140 mm gr 60 13 x 5.2 in Atova - Venetian Plasters Spatulas - Straight Edges Blades INOX Stainless steel, hand made tools made in Italy by Pavan Abrasive cloth change for wood handle scraper 621/R 330x140mm gr 16 13 x 5.2 in $ 10.95 621/R 330x140mm gr 24 13 x 5.2 in $ 10.95 621/R 330x140mm gr 60 13 x 5.2 in $ 10.95 Atova - Aluminium Hawk support for plasters - Rounded Edges Lightweight aluminum base. The small hawk is a perfect match for the small finishing trowel. Blades Stainless steel, hand made tools made in Italy by Pavan 890 180x180 mm 7.1 x 7.1 in $ 10.95 890 300x300 mm 11.8 x 11.8 in $ 17.95 Atova - Filling trowels - Straight Edges Blades Stainless steel, hand made tools made in Italy by Pavan Sintesi square short trowel. Swiss model 980/I 60 mm 3.9 in $ 11.95 980/I 80 mm 4.3 in $ 12.95
Atova is now a Distributor of 3M High Quality Inox Trowels and Spatulas. We provide a variety rubber and wood handled trowels with 3 sizes of blades and 2 thickness 0,5 and 0,6 mm. Exclusively for Atova, 3M has created a Linear Effect Tool. Available in 2 sizes 5x5 and 8x5. This special trowels is used to create Travertine, vertical and horizontal effects. This trowel is utilized to create many contemporary and modern finishes desired by architects and designers. Belty. This passion for design with roots in tradition and careful observation of users real needs has helped to create Belty, the professional tool belt that is a new concept in the decorators world and ensures that everything is within reach. Very comfortable to wear and made from abrasion-resistant technical fabric, the Belty tool offers users the advantage of never having to leave their working position at the top of a ladder or on scaffolding, while the firm fixing system prevents the dropping of tools which may cause nasty chips on blades, jeopardizing the overall quality of the job being done. Linear Trowels to create Traventino Effects
Atova - Venetian Plasters Trowels, Rubber Handles, Rounded Edges and Rectangular Blades Blades INOX Stainless steel, made in Italy by 3M 21080 200x80x0.5 mm 7.9x3.2 in $ 57.95 21081 240x100x0.5 mm 9.5x3.9 in $ 59.95 21070 200x80x0.6 mm 7.9x3.2 in $ 32.95 21071 240x100x0.6 mm 9.5x3.9 in $ 36.95 21072 280x120x0.6 mm 11x4.5 in $ 42.95 Atova - Venetian Plasters Trowels, Wood Handles, Rounded Edges and Rectangular Blades Blades INOX Stainless steel, made in Italy by 3M 21078 200x80x0.5 mm 7.9x3.2 in $ 35.95 21079 240x100x0.5 mm 9.5x3.9 in $ 37.95 21075 200x80x0.6 mm 7.9x3.2 in $ 28.95 21076 240x100x0.6 mm 9.5x3.9 in $ 31.95 21077 280x120x0.6 mm 11x4.5 in $ 35.95 Atova - Venetian Plasters Spatulas, Rubber Handles, Rounded Edges and Radius Blade Blades INOX Stainless steel, made in Italy by 3M 62040 40 mm 1.6 in $ 15.95 62060 60 mm 2.4 in $ 16.95 62080 80 mm 3.2 in $ 18.95 62100 100 mm 3.9 in $ 21.95 62120 120 mm 4.7 in $ 23.95 Atova - Exclusive -Linear Effect Trowel - used for achieving Traventino Effect made in Italy by 3M 25185 25186 130x130 mm 210xx130 mm 4.9x4.9 in 8x4.9 in $ 14.95 $ 21.95 Atova - Belty - the professional tool belt that is a new concept in the decorators world and ensures that everything is within reach - made in Italy by 3M 25185 130x130 mm 4.9x4.9 in $ 94.95
Hi polishing and Burning Trowel Inox-Rounded Edges-Trapezoid Soft Grip Boldrini Tools Linear Effect Trowel Exclusively for Atova plastic handle Price:$ TT55801 200x800mm 7.9x3.2in $40.95 25185 130x130mm 4.9x4.9 in $14.95 TT55802 240x100mm 9.5x3.9in $41.95 25186 210x130mm 8x4.9 in $21.95 TT55803 280x120mm 11x4.5in $42.95 Applying and polishing Trowel Inox-Rounded Edges-Trapezoid Soft Grip Price:$ TT55701 200x800mm 7.9x3.2in $34.95 TT55702 240x100mm 9.5x3.9in $35.95 TT55701 280x120mm 11x4.5in $36.95 Applying and polishing Trowel Inox-Rounded Edges-Trapezoid Wood Price:$ Price:$ Japanese Spatulas Knife Set of 4 TT424 60,80, 2.5, 3.2 100,120 mm 3.9, 4.7 in Price:$ $12.95 Battiore Buffer 100% bristle-solid wood frame TT2040 150x150mm 5.7x5.7 in Price:$ $66.95 Mini Vel Pen Brushlight wash pattern - soft brush TT20701 200x800mm 7.9x3.2in $31.95 Price:$ TT20702 240x100mm 9.5x3.9in $33.95 TT980 30x70mm 3 in $6.95 TT20703 280x120mm 11x4.5in $34.95 TT981 40x100mm 3.9 in $9.95 Team Tools Saptulas Soft Grip handle Inox-Stainless steel excellent flexability Price:$ TT20604 40mm 1.8 in $15.95 TT20606 60mm 2.6 in $21.95 TT20608 80mm 3.2 in $26.95 TT20612 120mm 4.7 in $29.95 TT2617 70mm CanOpene $16.95 Team Tools Saptulas Wood Grip handle Inox-Rounded Edges-Trapezoid Soft Grip TT555 12,14, 16cm 4.7-6.9in Large Spatula - Wood handle Price:$ TT425 500mm 19.7 in $25.33 Plastic - PCV spatula Light weight - transparent - flexible Price:$ TT144 230mm 9.1 in $66.95 Pro Plafonett - Brushes Price:$ Price:$ TT235.1 3x12x70cm 1.2x4.7x27.6in $12.95 $13.95 TT235.2 4x14x86cm 1.2x4.7x31.5in $16.95 TT235.3 5x15x76cm 5x5.9x35in $19.95 TT294 3x12x80cm 1.6x5.5x30in $17.95 Price:$ TT31 3x12x76cm 1.2x4.7x30in $14.95 TT245 5x15x89cm 2x5.9x30in $29.95 TT901 15, 20cm Stipler Brush Venice Brush 5.9, 7.9 in TT55801 200x800mm 7.9x3.2in $25.33 TT55802 240x100mm 9.5x3.9in $19.50 $29.95 Denim Brush Denim Buffer Price:$ TT2000 2x30 cm 0.8x11.8in $26.95 TT2010 6x30cm 2.4x11.8in $26.95 Wood Grainer Can Opener & Mixer Price:$ TT934 150mm 5.9 in $29.95 TTB1 300mm 12 in $8.95 Atova International 2452 N Harlem, Elmwood Park, IL 60707 Phone: 708-452-9982, Fax: 708-452-8331 info@paintandplasters.com www.paintandplasters.com