PUBLISHED WEEKLY BY THE AMERICAN NATIONAL STANDARDS INSTITUTE 25 West 43rd Street, NY, NY 10036 VOL. 47, #30 July 22, 2016 Contents American National Standards Call for Comment on Standards Proposals... 2 Call for Members (ANS Consensus Bodies)... 8 Final Actions... 11 Project Initiation Notification System (PINS)... 13 ANS Maintained Under Continuous Maintenance... 16 ANSI-Accredited Standards Developers Contact Information... 17 International Standards ISO and IEC Draft Standards... 18 ISO and IEC Newly Published Standards... 22 Proposed Foreign Government Regulations... 25 Information Concerning... 26 American National Standards Call for comment on proposals listed This section solicits public comments on proposed draft new American National Standards, including the national adoption of ISO and IEC standards as American National Standards, and on proposals to revise, reaffirm or withdraw approval of existing American National Standards. A draft standard is listed in this section under the ANSI-accredited standards developer (ASD) that sponsors it and from whom a copy may be obtained. Comments in connection with a draft American National Standard must be submitted in writing to the ASD no later than the last day of the comment period specified herein. Such comments shall be specific to the section(s) of the standard under review and include sufficient detail so as to enable the reader to understand the commenter's position, concerns and suggested alternative language, if appropriate. Please note that the ANSI Executive Standards Council (ExSC) has determined that an ASD has the right to require that interested parties submit public review comments electronically, in accordance with the developer s procedures. Ordering Instructions for "Call-for-Comment" Listings 1. Order from the organization indicated for the specific proposal. 2. Use the full identification in your order, including the BSR prefix; for example, Electric Fuses BSR/SAE J554. 3. Include remittance with all orders. 4. BSR proposals will not be available after the deadline of call for comment. Comments should be addressed to the organization indicated, with a copy to the Board of Standards Review, American National Standards Institute, 25 West 43rd Street, New York, NY 10036. Fax: 212-840-2298; e-mail: psa@ansi.org * Standard for consumer products 2016 by American National Standards Institute, Inc. ISSN 0038-9633 ANSI members may reproduce for internal distribution. Journals may excerpt items in their fields
Comment Deadline: August 21, 2016 NSF (NSF International) BSR/NSF 14-201x (i76r1), Plastics Piping System Components and Related Materials (revision of ANSI/NSF 14-2015) This Standard establishes minimum physical, performance, and health effects requirements for plastics piping system components and related materials. These criteria were established for the protection of public health and the environment. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Lauren Panoff, (734) 769-5197, lpanoff@nsf.org NSF (NSF International) BSR/NSF 42-201x (i87r1), Drinking Water Treatment Units - Aesthetic Effects (revision of ANSI/NSF 42-2015) It is the purpose of this Standard to establish minimum requirements for materials, design and construction, and performance of drinking water treatment systems that are designed to reduce specific aesthetic-related (non-health effects) contaminants in public or private water supplies. This Standard also specifies the minimum product literature and labeling information that a manufacturer shall supply to authorized representatives and system owners as well as the minimum service-related obligations that the manufacturer shall extend to system owners. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Monica Leslie, (734) 827-5643, mleslie@nsf.org NSF (NSF International) BSR/NSF 53-201x (i103r1), Drinking Water Treatment Units - Health Effects (revision of ANSI/NSF 53-2015) It is the purpose of this Standard to establish minimum requirements for materials, design and construction, and performance of point-of-use and point-of-entry drinking water treatment systems that are designed to reduce specific health-related contaminants in public or private water supplies. Such systems include point-of-entry drinking water treatment systems used to treat all or part of the water at the inlet to a residential facility or a bottled water production facility, and includes the material and components used in these systems. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Monica Leslie, (734) 827-5643, mleslie@nsf.org UL (Underwriters Laboratories, Inc.) Standards Action - July 22, 2016 - Page 2 of 38 Pages BSR/UL 1238-201x, Standard for Safety for Control Equipment for Use with Flammable Liquid Dispensing Devices (revision of ANSI/UL 1238-2015) The following topic is being proposed: (1) Add laminated glass and glass with protective coatings for panels. Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Marcia Kawate, Marcia.M. Kawate@ul.com Comment Deadline: September 5, 2016 AAMI (Association for the Advancement of Medical Instrumentation) BSR/AAMI/ISO 16142-2-201x, Medical devices - Recognized essential principles of safety and performance of medical devices - Part 2: General essential principles and additional specific essential principles for all IVD medical devices and guidance on the selection of standards (revision and partition of ISO 16142) This part of ISO 16142, which includes the essential principles of safety and performance, identifies significant standards and guides that can be used in the assessment of conformity of a medical device to the recognized essential principles that when met, indicate a medical device is safe and performs as intended. This standard identifies and describes the six general essential principles of safety and performance that apply to all medical devices, including IVD medical devices (in vitro diagnostic). Single copy price: Free Obtain an electronic copy from: https://standards.aami. org/kws/public/document?document_id=9608&wg_abbrev=public_rev Order from: https://standards.aami.org/kws/public/document? document_id=9608&wg_abbrev=public_rev Send comments (with copy to psa@ansi.org) to: wvargas@aami.org AHRI (Air-Conditioning, Heating, and Refrigeration Institute) New Standard BSR/AHRI Standard 910 (I-P)-201x, Performance Rating of Indoor Pool Dehumidifiers (new standard) This standard applies to factory-made residential, commercial and industrial Indoor Pool Dehumidifiers, as defined in Section 3. Single copy price: Free Order from: Daniel Abbate, (703) 600-0327, dabbate@ahrinet.org NSF (NSF International) BSR/NSF 305-201x (i22r3), Personal Care Products Containing Organic Ingredients (revision of ANSI/NSF 305-2014) This Standard specifies materials, processes, production criteria, and conditions that shall be met in order for personal care products to make organic label and marketing claims under this Standard. This Standard intends to address products with a minimum organic content of 70% (O70). Click here to view these changes in full Send comments (with copy to psa@ansi.org) to: Allan Rose, (734) 827-3817, arose@nsf.org
Standards Action - July 22, 2016 - Page 3 of 38 Pages APCO (Association of Public-Safety Communications Officials-International) New Standard BSR/APCO 1.113.1-201x, Public Safety Communications Incident Handling Process (new standard) The standard will take the call handling process from its root. Starting with the call delivery mechanism of equipment which can affect the call handling initiation it will continue to the actual triage of the call to its dissemination. The goal is to bring the incident-handling process into full circle from the initiation of the incident through the triage and finally into the dissemination of information. This will include the continued support of responders through the dissemination portion. Single copy price: Free Obtain an electronic copy from: mcduffiec@apcointl.org Order from: Crystal McDuffie, (386) 322-2500, mcduffiec@apcointl.org; standards@apcointl.org APCO (Association of Public-Safety Communications Officials-International) BSR/APCO 3.101.3-201x, Core Competencies and Minimum Training Standards for Public Safety Communications Training Officer (CTO) (revision and redesignation of ANSI/APCO ANS 3.101.2-2013) The standard revision provides the minimum training requirements for individuals responsible for public safety communications training programs as well as the knowledge, skills, and traits of the individual(s) responsible for this critical function. Single copy price: Free Obtain an electronic copy from: mcduffiec@apcointl.org Order from: Crystal McDuffie, (386) 322-2500, mcduffiec@apcointl.org; standards@apcointl.org APCO (Association of Public-Safety Communications Officials-International) BSR/APCO 3.102.2-201x, Core Competencies and Minimum Training Standards for Public Safety Communications Supervisors (revision and redesignation of ANSI/APCO 3.102.1-2012) This standard revision identifies the core competencies and minimum training requirements for Public Safety Communications Supervisors. This position is typically tasked with managing daily operations, performing administrative duties and maintaining employee relations. This position provides leadership and guidance to employees in order to achieve the Agency s mission, while providing service to the public and emergency responders. Single copy price: Free Obtain an electronic copy from: mcduffiec@apcointl.org Order from: Crystal McDuffie, (386) 322-2500, mcduffiec@apcointl.org; standards@apcointl.org APCO (Association of Public-Safety Communications Officials-International) BSR/APCO 3.106.2-201x, Core Competencies and Minimum Training Standards for Public Safety Communications Quality Assurance Evaluators (revision and redesignation of ANSI/APCO 3.106.1-2013) This revision Identifies the core competencies and minimum training requirements for Public Safety Communications Quality Assurance Evaluators (QAE). The QAE administers the Quality Assurance/Quality Improvement (QA/QI) processes. Single copy price: Free Obtain an electronic copy from: mcduffiec@apcointl.org Order from: Crystal McDuffie, (386) 322-2500, mcduffiec@apcointl.org; standards@apcointl.org ASCE (American Society of Civil Engineers) New Standard BSR/ASCE/EWRI xxyy-201x, Management Practices for Control of Erosion and Sediment from Construction Activities (new standard) This standard covers the successful implementation of an erosion and sediment control program is a multifaceted undertaking that includes a mix of administrative, legal, and technical issues. This document provides guidelines for personnel involved in the implementation of erosion and sediment control programs. Single copy price: Free Obtain an electronic copy from: jneckel@asce.org Order from: James Neckel, 703-295-6176, jneckel@asce.org ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) BSR/ASHRAE Standard 120-201x, Method of Testing to Determine Flow Resistance of HVAC Ducts and Fittings (revision of ANSI/ASHRAE Standard 120-2008) This revision of Standard 120-2008 establishes uniform methods of laboratory testing of HVAC ducts and fittings to determine their resistance to airflow. The fitting losses, which are reported as local loss coefficients, are used to update and refine the ASHRAE Duct Fitting Database. Single copy price: $35.00 Obtain an electronic copy from: http://www.ashrae.org/standards-research-- technology/public-review-drafts Order from: standards.section@ashrae.org Send comments (with copy to psa@ansi.org) to: http://www.ashrae. org/standards-research--technology/public-review-drafts
Standards Action - July 22, 2016 - Page 4 of 38 Pages ATIS (Alliance for Telecommunications Industry Solutions) Stabilized Maintenance BSR/ATIS 0300206-2001 (S201x), Digital Exchanges and PBXs - Digital Circuit Loopback Test Line with N [infinity] DS0 Capability (stabilized maintenance of ANSI/ATIS 0300206-2001 (R2011)) This standard specifies a loopback test line capable of being used in the measurement of error performance of switched digital circuits. In order to carry out maintenance in the public switched telephone network of switched 64-kbit/s digital circuits, digital circuits at sub-rates of 64 kbits/s and N [infinity] DS0 digital circuits (up to the maximum payload of a primary rate facility), a digital circuit test system is defined for digital exchanges and digital PBXs. Currently, only digital loopback testing is defined in this standard. Single copy price: $60.00 Order from: Alexandra Blasgen, (202) 434-8840, ablasgen@atis.org ATIS (Alliance for Telecommunications Industry Solutions) Withdrawal ANSI/ATIS 0300228-2011, OAM&P - Services for Interfaces between Operations Systems across Jurisdictional Boundaries to Support Fault Management (Trouble Administration) (withdrawal of ANSI/ATIS 0300228-2011) This standard is the first in a series of standard that specify interface requirements between Operations Systems (OSs) across jurisdictional boundaries. It describes a set of Fault Management functional area services for Operations Administration, Maintenance, and Provisioning (OAM&P) applications. The current issue of this standard addresses only trouble administration. Single copy price: $145.00 Order from: Alexandra Blasgen, (202) 434-8840, ablasgen@atis.org ATIS (Alliance for Telecommunications Industry Solutions) Stabilized Maintenance BSR/ATIS 0300226-2001 (S201x), Operations, Administration, Maintenance, and Provisioning (OAM&P) - Management of Functions for Signalling System No. 7 (SS7) Network Interconnections (stabilized maintenance of ANSI/ATIS 0300226-2001 (R2011)) This standard addresses Operations, Administration, Maintenance, and Provisioning (OAM&P) for internetwork connections employing Common Channel Signalling (CCS) based on Signalling system Number 7 (SS7) protocol used in North America. This standard presents principles, specifies requirements, describes architectures and protocol procedures, and identifies strategies for performance of OAM&P functions, including compatibility verification and gateway screening. It identifies procedures, actions, and responsibilities for performance of functions for management of network interconnections. Single copy price: $330.00 Order from: Alexandra Blasgen, (202) 434-8840, ablasgen@atis.org ATIS (Alliance for Telecommunications Industry Solutions) Stabilized Maintenance BSR/ATIS 0300236-2005 (S201x), Signaling System 7 (SS7) - ISDN User Part Compatibility Testing (stabilized maintenance of ANSI/ATIS 0300236-2005 (R2011)) This standard addresses the testing required for internetwork connections employing Common Channel Signaling (CCS) based on Signaling System No. 7 (SS7) protocol used in North America. The internetwork connection may be either within or between North American countries. This standard provides a list of test scripts for testing compatibility between the interconnecting networks of the ISDN User Part (ISUP) of the SS7 protocol used for call control and circuit supervision. Single copy price: $220.00 Order from: Alexandra Blasgen, (202) 434-8840, ablasgen@atis.org ATIS (Alliance for Telecommunications Industry Solutions) Withdrawal ANSI/ATIS 0300274-2000 (R2011), Electronic Interactive Agent (IA) (withdrawal of ANSI/ATIS 0300274-2000 (R2011)) This Standard specifies a U.S. standard for an Electronic Interactive Agent (IA) to transport EDI/EDIFACT, XML and/or plain text messages over a TCP/IP based network environment utilizing Transport Layer Security (TLS). This standard is based on ITU-T Recommendations Q.814 and Q.815, but has minor differences to improve its efficiency in the U.S. community. Single copy price: $110.00 Order from: Alexandra Blasgen, (202) 434-8840, ablasgen@atis.org CSA (CSA Group) New Standard BSR/CSA LNG 2-201x, Liquefied natural gas vehicle containers (new standard) This Standard contains performance requirements for the material, design, marking, and testing of serially produced, refillable containers intended only for the storage of liquefied natural gas for vehicle operation. These containers are to be affixed to the vehicle. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) 524-4990 x88321, cathy.rake@csagroup.org CSA (CSA Group) BSR Z21.11.2-201x, Gas-Fired Room Heaters, Volume II, Unvented Room Heaters (revision of ANSI Z21.11.2-2011) Details test and examination criteria for unvented heaters for use with natural, manufactured and mixed gases, liquefied petroleum gases, and LP gas-air mixtures. Such heaters are limited to maximum input ratings of 40,000 Btu per hour. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) 524-4990 x88321, cathy.rake@csagroup.org
Standards Action - July 22, 2016 - Page 5 of 38 Pages CSA (CSA Group) BSR Z21.11.3-201x, Gas-Fired Room Heaters, Volume III, Propane-Fired Portable Emergency Use Heater Systems (revision of ANSI Z21.11.3-2013) Details test and examination criteria for propane-fired portable emergency use heater systems for use with a self-contained propane supply in a listed composite cylinder. Such heater systems are not for use with line voltage and limited to a maximum input rating of 15,000 Btu/hr (4396 W). Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) 524-4990 x88321, cathy.rake@csagroup.org FCI (Fluid Controls Institute) BSR/FCI 69-1-201x, Pressure Rating Standard for Steam Traps (revision of ANSI/FCI 69-1-1989 (R2004)) The standard provides the minimum requirements for the design, fabrication, pressure rating, and marking of pressure-containing housings for steam traps. Single copy price: Free Obtain an electronic copy from: FCI Order from: FCI Send comments (with copy to psa@ansi.org) to: Leslie Schraff, Fluid Controls Institute CSA (CSA Group) BSR Z21.50-201x, Vented Decorative Gas Appliances (same as CSA 2.22-201x) (revision of ANSI Z21.50-2014) Details test and examination criteria for vented gas fireplace for use with natural and propane gases. The only function of a vented gas fireplace lies in the aesthetic effect of the flame; the appliance is not a source of heat. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) 524-4990 x88321, cathy.rake@csagroup.org CSA (CSA Group) BSR Z21.86-201x, Vented Gas-Fired Space Heating Appliances (same as CSA 2.32-201x) (revision of ANSI Z21.86-2008 (R2013)) Details test and examination criteria for vented room heaters, direct vent wall furnaces, vented wall furnaces, and gravity and fan-type floor furnaces for use with natural, manufactured and mixed gases; liquefied petroleum gases; and LP gas-air mixtures. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) 524-4990 x88321, cathy.rake@csagroup.org CSA (CSA Group) BSR Z21.88-201x, Vented Gas Fireplace Heaters (same as CSA 2.33-201x) (revision of ANSI Z21.88-2014) Test and examination criteria for vented gas fireplace heaters for use with natural and liquefied petroleum (propane) gases, which allows the view of flames and provides the simulation of a solid fuel fireplace and furnishes warm air to the space in which it is installed with or without duct connections. A vented gas-fired fireplace heater is designed to comply with the minimum thermal efficiency requirements and may be controlled by an automatic thermostat. Direct vent appliances may be installed in manufactured (mobile) homes and recreational vehicles. Single copy price: Free Obtain an electronic copy from: cathy.rake@csagroup.org Order from: Cathy Rake, (216) 524-4990 x88321, cathy.rake@csagroup.org NEBB (National Environmental Balancing Bureau) New Standard BSR/NEBB S120-201x, Technical Retro-Commissioning of Existing Buildings Standard (new standard) This standard describes the technical retro-commissioning procedures utilized for existing building technical systems for the improvement and optimization of Indoor Environmental Quality and Comfort and Energy and Water utility usage reduction. It defines the technical work procedures, testing, and system adjustments that are required to improve system performance by optimizing existing systems. This standard may be utilized in tandem with existing energy audit standards as a technical performance standard. Single copy price: Free Obtain an electronic copy from: tiffany@nebb.org, http://www.nebb. org/resources/nebb_ansi_accredited_standards_developer_asd/ Send comments (with copy to psa@ansi.org) to: tiffany@nebb.org NSF (NSF International) BSR/NSF 60-201x (i75r1), Drinking Water Treatment Chemicals (revision of ANSI/NSF 60-2015) This Standard establishes minimum health-effects requirements for the chemicals, the chemical contaminants, and the impurities that are directly added to drinking water from drinking-water treatment chemicals. This Standard does not establish performance or taste and odor requirements for drinking-water treatment chemicals. Single copy price: Free Obtain an electronic copy from: http://standards.nsf. org/apps/group_public/download.php/33723/60i75r1%20et%20al%20jc% 20memo%20&%20ballot.pdf Order from: Monica Leslie, (734) 827-5643, mleslie@nsf.org
Standards Action - July 22, 2016 - Page 6 of 38 Pages NSF (NSF International) BSR/NSF 61-201x (i133r1), Drinking Water System Components - Health Effects (revision of ANSI/NSF 61-2015) This Standard establishes minimum health effects requirements for the chemical contaminants and impurities that are indirectly imparted to drinking water from products, components, and materials used in drinking water systems. This Standard does not establish performance, taste and odor, or microbial growth support requirements for drinking-water-system products, components, or materials. Single copy price: Free Obtain an electronic copy from: http://standards.nsf. org/apps/group_public/download.php/33723/60i75r1%20et%20al%20jc% 20memo%20&%20ballot.pdf Order from: Monica Leslie, (734) 827-5643, mleslie@nsf.org OEOSC (ASC OP) (Optics and Electro-Optics Standards Council) BSR/OEOSC OP1.002-201x, Optics and Electro-Optical Instruments - Optical Elements and Assemblies - Surface Imperfections (revision of ANSI/OEOSC OP1.002-2009) This Standard establishes uniform practices for stating and interpreting tolerances and for conducting inspections of transmissive and reflective optical elements and cemented components for scratch, dig, edge, coating, and optical cement imperfections. Default specifications for bubbles and inclusions are also included. Single copy price: $50.00 Obtain an electronic copy from: allen@oeosc.org Order from: Allen Krisiloff, 585-473-4470, allen@oeosc.org SCTE (Society of Cable Telecommunications Engineers) New Standard BSR/SCTE 220-2-201x, DOCSIS 3.1 Part 2: Media Access Control (MAC) and Upper Layer Protocols Interface Specification (new standard) This generation of the DOCSIS specifications builds upon the previous generations of DOCSIS specifications (commonly referred to as the DOCSIS 3.0 and earlier specifications), leveraging the existing Media Access Control (MAC) and Physical (PHY) layers, but with the addition of a new PHY layer designed to improve spectral efficiency and provide better scaling for larger bandwidths (and appropriate updates to the MAC and management layers to support the new PHY layer). It includes backward compatibility for the existing PHY layers in order to enable a seamless migration to the new technology. Single copy price: $50.00 Obtain an electronic copy from: standards@scte.org Order from: Global Engineering Documents, (800) 854-7179, www.global. ihs.com Send comments (with copy to psa@ansi.org) to: standards@scte.org SCTE (Society of Cable Telecommunications Engineers) New Standard BSR/SCTE 220-3-201x, DOCSIS 3.1 Part 3: Cable Modem Operations Support System Interface Specification (new standard) This standard is part of the DOCSIS family of specifications. In particular, this standard is part of a series of standards that define the fifth generation of high-speed data-over-cable systems, DOCSIS 3.1. This standard was developed for the benefit of the cable industry, and includes contributions by operators and vendors from North America, Europe, and other regions. Single copy price: $50.00 Obtain an electronic copy from: standards@scte.org Order from: Global Engineering Documents, (800) 854-7179, www.global. ihs.com Send comments (with copy to psa@ansi.org) to: standards@scte.org SCTE (Society of Cable Telecommunications Engineers) New Standard BSR/SCTE 220-1-201x, DOCSIS 3.1 Part 1: Physical Layer Specification (new standard) This generation of the DOCSIS specifications builds upon the previous generations of DOCSIS specifications (commonly referred to as the DOCSIS 3.0 and earlier specifications), leveraging the existing Media Access Control (MAC) and Physical (PHY) layers, but with the addition of a new PHY layer designed to improve spectral efficiency and provide better scaling for larger bandwidths (and appropriate updates to the MAC and management layers to support the new PHY layer). It includes backward compatibility for the existing PHY layers in order to enable a seamless migration to the new technology. Single copy price: $50.00 Obtain an electronic copy from: standards@scte.org Order from: Global Engineering Documents, (800) 854-7179, www.global. ihs.com Send comments (with copy to psa@ansi.org) to: standards@scte.org SCTE (Society of Cable Telecommunications Engineers) New Standard BSR/SCTE 220-4-201x, DOCSIS 3.1 Part 4: CCAP Operations Support System Interface Specification (new standard) This document defines the requirements necessary for the configuration, fault management, and performance management of the Cable Modem Termination System (CMTS) and the Converged Cable Access Platform (CCAP) system. The intent of this standard is to define a common, crossvendor set of functionality for the configuration and management of CMTSs and CCAPs. Single copy price: $50.00 Obtain an electronic copy from: standards@scte.org Order from: Global Engineering Documents, (800) 854-7179, www.global. ihs.com Send comments (with copy to psa@ansi.org) to: standards@scte.org
Standards Action - July 22, 2016 - Page 7 of 38 Pages SCTE (Society of Cable Telecommunications Engineers) New Standard BSR/SCTE 220-5-201x, DOCSIS 3.1 Part 5: Security Specification (new standard) This standard is part of the DOCSIS family of specifications. In particular, this standard is part of a series of standards that define the fifth generation of high-speed data-over-cable systems. This standard was developed for the benefit of the cable industry, and includes contributions by operators and vendors from North America, Europe, and other regions. Single copy price: $50.00 Obtain an electronic copy from: standards@scte.org Order from: Global Engineering Documents, (800) 854-7179, www.global. ihs.com Send comments (with copy to psa@ansi.org) to: standards@scte.org Comment Deadline: September 20, 2016 AWS (American Welding Society) ANSI/AWS B2.1-1-022-2005, Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E6010 (Vertical Uphill) Followed by E7018, As-Welded or PWHT Condition AWS (American Welding Society) ANSI/AWS B2.1-1-026-2005, Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E6010 (Vertical Downhill) Followed by E7018, As-Welded or PWHT Condition AWS (American Welding Society) ANSI/AWS B2.1-8-023-2005, Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Austenitic Stainless Steel (M-8/P -8/S-8, Group 1), 1/8 through 1-1/2 inch Thick, As-Welded Condition ASME (American Society of Mechanical Engineers) BSR/ASME B16.21-201x, Nonmetallic Flat Gaskets for Pipe Flanges (revision of ANSI/ASME B16.21-2011) This Standard covers types, sizes, materials, dimensions, tolerances, and markings for nonmetallic flat gaskets. These gaskets are dimensionally suitable for use with flanges described in the referenced flange standards. Single copy price: Free Obtain an electronic copy from: http://cstools.asme.org/publicreview Order from: Mayra Santiago, (212) 591-8521, ansibox@asme.org Send comments (with copy to psa@ansi.org) to: Carlton Ramcharran, (212) 591-7955, ramcharranc@asme.org 30 Day Notice of Withdrawal: ANS 5 to 10 years past approval date In accordance with clause 4.7.1 Periodic Maintenance of American National Standards of the ANSI Essential Requirements, the following American National Standards have not been reaffirmed or revised within the five-year period following approval as an ANS. Thus, they shall be withdrawn at the close of this 30-day public review notice in Standards Action. AWS (American Welding Society) ANSI/AWS B2.1-1-016-2005, Standard Welding Procedure Specification (WPS) for Shielded Metal Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E7018, As-Welded or PWHT Condition AWS (American Welding Society) ANSI/AWS B2.1-1-019-2005, Standard Welding Procedure Specification (WPS) for CO2 Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P -1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E70T-1 and E71T-1, As- Welded Condition AWS (American Welding Society) ANSI/AWS B2.1-1-020-2005, Standard Welding Procedure Specification (WPS) for 75% Ar/25% CO2 Shielded Flux Cored Arc Welding of Carbon Steel (M-1/P-1/S-1, Group 1 or 2), 1/8 through 1-1/2 inch Thick, E70T-1 and E71T-1, As-Welded or PWHT Condition
Standards Action - July 22, 2016 - Page 8 of 38 Pages Call for Members (ANS Consensus Bodies) Directly and materially affected parties who are interested in participating as a member of an ANS consensus body for the standards listed below are requested to contact the sponsoring standards developer directly and in a timely manner. AAMI (Association for the Advancement of Medical Instrumentation) Office: 4301 N Fairfax Drive Suite 301 Arlington, VA 22203-1633 Phone: Will Vargas (703) 647-2779 wvargas@aami.org BSR/AAMI/ISO 16142-2-201x, Medical devices - Recognized essential principles of safety and performance of medical devices - Part 2: General essential principles and additional specific essential principles for all IVD medical devices and guidance on the selection of standards (revision and partition of ANSI/AAMI/ISO 16142-2-201x) Obtain an electronic copy from: https://standards.aami. org/kws/public/document? document_id=9608&wg_abbrev=public_rev AHRI (Air-Conditioning, Heating, and Refrigeration Institute) Office: Phone: Fax: 2111 Wilson Boulevard Suite 500 Arlington, VA 22201 Daniel Abbate (703) 600-0327 (703) 562-1942 dabbate@ahrinet.org BSR/AHRI Standard 910 (I-P)-201x, Performance Rating of Indoor Pool Dehumidifiers (new standard) ASSE (ASC A10) (American Society of Safety Engineers) Office: Phone: Fax: 520 N. Northwest Highway Park Ridge, IL 60068 Tim Fisher (847) 768-3411 (847) 296-9221 TFisher@ASSE.org BSR ASSE A10.11-201X, Safety Requirements for Personnel Nets (revision of ANSI ASSE A10.11-2010) Obtain an electronic copy from: Tim Fisher FCI (Fluid Controls Institute) Office: Phone: Fax: 1300 Sumner Avenue Cleveland, OH 44115 Leslie Schraff (216) 241-7333 (216) 241-0105 fci@fluidcontrolsinstitute.org BSR/FCI 69-1-201x, Pressure Rating Standard for Steam Traps (revision of ANSI/FCI 69-1-1989 (R2004)) Obtain an electronic copy from: FCI NEMA (ASC C18) (National Electrical Manufacturers Association) Office: Phone: Fax: 1300 North 17th Street Suite 900 Rosslyn, VA 22209 Khaled Masri (703) 841-3278 (703) 841-3367 khaled.masri@nema.org BSR C18.2M, Part 1-201x, Standard for Portable Rechargeable Cells and Batteries - General and Specifications (revision of ANSI C18.2M, Part 1-2013) SDI (ASC A250) (Steel Door Institute) Office: Phone: Fax: 30200 Detroit Road Westlake, OH 44145 Linda Hamill (440) 899-0010 (440) 892-1404 leh@wherryassoc.com BSR A250.3-201x, Test Procedure and Acceptance Criteria for Factory Applied Finish Coatings for Steel Doors and Frames (revision of ANSI A250.3-2007 (R2011)) BSR A250.4-201x, Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors, Frames, and Frame Anchors (revision of ANSI A250.4-2011) BSR A250.10-201x, Test Procedure and Acceptance Criteria for Prime Painted Steel Surfaces for Steel Doors and Frames (revision of ANSI A250.10-2011) Obtain an electronic copy from: sab@wherryassoc.com
Standards Action - July 22, 2016 - Page 9 of 38 Pages TIA (Telecommunications Industry Association) Office: Phone: Fax: 1320 North Courthouse Road Suite 200 Arlington, VA 22201 Teesha Jenkins (703) 907-7706 (703) 907-7727 standards@tiaonline.org BSR/TIA 604-18-A-201x, FOCIS 18 - Fiber Optic Connector Intermateability Standard Type MPO-16 (revision and redesignation of ANSI/TIA 604-18-2015) UL (Underwriters Laboratories, Inc.) Office: 47173 Benicia Street Fremont, CA 94538 Marcia Kawate Marcia.M.Kawate@ul.com BSR/UL 1238-201x, Standard for Safety for Control Equipment for Use with Flammable Liquid Dispensing Devices (revision of ANSI/UL 1238-2015) Obtain an electronic copy from: http://www.comm-2000.com
Standards Action - July 22, 2016 - Page 10 of 38 Pages Call for Members (ANS Consensus Bodies) Call for Committee Members ASC O1 Are you interested in contributing to the development and maintenance of valuable industry safety standards? The ASC O1 is currently looking for members in the following categories: o General Interest o Government o Producer o User If you are interested in joining the ASC O1, contact WMMA Associate Director Jennifer Miller at jennifer@wmma.org.
Standards Action - July 22, 2016 - Page 11 of 38 Pages Final Actions on American National Standards The standards actions listed below have been approved by the ANSI Board of Standards Review (BSR) or by an ANSI-Audited Designator, as applicable. AAMI (Association for the Advancement of Medical Instrumentation) Reaffirmation ANSI/AAMI/ISO 15225-2016, Medical devices - Quality management - Medical device nomenclature data structure (reaffirmation of ANSI/AAMI/ISO 15225-2010): 7/7/2016 ANSI/AAMI/ISO 16142-1-2016, Medical devices - Recognized essential principles of safety and performance of medical devices - Part 1: General essential principles and additional specific essential principles for all non-ivd medical devices and guidance on the selection of standards (revision and partition of ISO 16142): 7/7/2016 AHRI (Air-Conditioning, Heating, and Refrigeration Institute) New Standard ANSI/AHRI Standard 911 (SI)-2014, Performance Rating of Indoor Pool Dehumidifiers (new standard): 7/8/2016 ANSI/AHRI Standard 300-2015, Sound Rating and Sound Transmission Loss of Packaged Terminal Equipment (revision of ANSI/AHRI Standard 300-2009): 7/8/2016 ANSI/AHRI Standard 580-2014, Performance Rating of Non- Condensable Gas Purge Equipment for Use with Low Pressure Centrifugal Liquid Chillers (revision of ANSI/AHRI Standard 580-2010): 7/8/2016 ANSI/AHRI Standard 680 (I-P)-2015, Performance Rating of Residential Air Filter Equipment (revision of ANSI/AHRI Standard 680 (I-P)-2010): 7/8/2016 ANSI/AHRI Standard 681 (SI)-2015, Performance Rating of Residential Air Filter Equipment (revision of ANSI/AHRI Standard 681 (SI)-2010): 7/8/2016 ANSI/AHRI Standard 1360 (I-P)-2016, Performance Rating of Computer and Data Processing Room Air Conditioners (revision of ANSI/AHRI Standard 1360 (I-P)-2013): 7/8/2016 ANSI/AHRI Standard 1361 (SI)-2016, Performance Rating of Computer and Data Processing Room Air Conditioners (revision of ANSI/AHRI Standard 1361 (SI)-2013): 7/8/2016 AISC (American Institute of Steel Construction) ANSI/AISC 360-2016, Specification for Structural Steel Buildings (revision of ANSI/AISC 360-2010): 7/7/2016 ANS (American Nuclear Society) Reaffirmation ANSI/ANS 57.10-1996 (R2016), Design Criteria for Consolidation of LWR Spent Fuel (reaffirmation of ANSI/ANS 57.10-1996 (R2006)): 7/7/2016 ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) Addenda ANSI/ASHRAE Standard 15c-2016, Safety Standard for Refrigeration Systems (addenda to ANSI/ASHRAE Standard 15-2013): 6/30/2016 ANSI/ASHRAE Standard 15e-2016, Safety Standard for Refrigeration Systems (addenda to ANSI/ASHRAE Standard 15-2013): 6/30/2016 ANSI/ASHRAE Standard 15g-2016, Safety Standard for Refrigeration Systems (addenda to ANSI/ASHRAE Standard 15-2013): 6/30/2016 ANSI/ASHRAE/IES 90.1dd-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1ao-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1bh-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1bi-2016, Energy Standard for Buildings Except Low-Rise Residential Buildings (addenda to ANSI/ASHRAE/IESNA Standard 90.1-2013): 6/30/2016 ANSI/ASHRAE/IES 90.1bk-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1bo-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1ca-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1cn-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1co-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1cp-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1cq-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1ct-2016, Energy Standard for Buildings Except Low-Rise Residential Buildings (addenda to ANSI/ASHRAE/IESNA Standard 90.1-2013): 6/30/2016 ANSI/ASHRAE/IES 90.1cv-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1da-2016, Energy Standard for Buildings
Standards Action - July 22, 2016 - Page 12 of 38 Pages ANSI/ASHRAE/IES 90.1db-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1dc-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1dg-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1dh-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1di-2016, Energy Standard for Buildings Except Low-Rise Residential Buildings (addenda to ANSI/ASHRAE/IESNA Standard 90.1-2013): 6/30/2016 ANSI/ASHRAE/IES 90.1dk-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1dp-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1dq-2016, Energy Standard for Buildings ANSI/ASHRAE/IES 90.1dr-2016, Energy Standard for Buildings ITI (INCITS) (InterNational Committee for Information Technology Standards) New Standard INCITS 501-2016, Information technology - Security Features for SCSI Commands (SFSC) (new standard): 7/7/2016 INCITS 511-2016, Information Technology - Fibre Channel - Switch Fabric - 6 (FC-SW-6) (new standard): 7/7/2016 NEMA (ASC C119) (National Electrical Manufacturers Association) ANSI C119.4-2016, Connectors for Use between Aluminum-to- Aluminum and Aluminum-to-Copper Conductors Designed for Normal Operation at or below 93 C and Copper-to-Copper Conductors Designed for Normal Operation at or below 100 C (revision of ANSI C119.4-2010): 7/7/2016 * * NEMA (ASC C8) (National Electrical Manufacturers Association) New Standard ANSI/ICEA S-113-684-2016, Peformance-Based Standard for Electric Utility Extruded Dielectric Shielded Power Cables Rated 5 Through 46 KV (new standard): 7/7/2016 NSF (NSF International) ANSI/NSF 49-2016 (i86r1), Biosafety Cabinetry: Design, Construction, Performance, and Field Certification (revision of ANSI/NSF 49-2014): 7/1/2016 SCTE (Society of Cable Telecommunications Engineers) ANSI/SCTE 35-2016, Digital Program Insertion Cueing Message for Cable (revision of ANSI/SCTE 35-2014): 7/8/2016 UL (Underwriters Laboratories, Inc.) ANSI/UL 147-2016, Standard for Safety for Hand-Held Torches for Fuel Gases (revision of ANSI/UL 147-2015): 7/7/2016 ANSI/UL 498-2016c, Standard for Safety for Attachment Plugs and Receptacles (revision of ANSI/UL 498-2016): 7/7/2016 ANSI/UL 778-2016, Standard for Safety for Motor-Operated Water Pumps (revision of ANSI/UL 778-2015): 7/7/2016 ANSI/UL 1610-2016, Standard for Safety for Central-Station Burglar- Alarm Units (revision of ANSI/UL 1610-2015a): 7/5/2016 ANSI/UL 1610-2016a, Standard for Safety for Central-Station Burglar- Alarm Units (revision of ANSI/UL 1610-2015a): 7/5/2016 ANSI/UL 1610-2016b, Standard for Safety for Central-Station Burglar- Alarm Units (revision of ANSI/UL 1610-2015a): 7/5/2016 ANSI/UL 1610-2016c, Standard for Safety for Central-Station Burglar- Alarm Units (revision of ANSI/UL 1610-2015): 7/5/2016 ANSI/UL 1610-2016d, Standard for Safety for Central-Station Burglar- Alarm Units (revision of ANSI/UL 1610-2015): 7/5/2016 ANSI/UL 60691-2016, Standard for Safety for Thermal-Links - Requirements and Application Guide (revision of ANSI/UL 60691-2011): 6/30/2016 * NEMA (ASC C78) (National Electrical Manufacturers Association) ANSI C78.40-2016, Electric Lamps - Specifications for Mercury Lamps (revision of ANSI C78.40-2011): 7/7/2016 ANSI C78.380-2016, Electric Lamps: High-Intensity Discharge Lamps, Method of Designation (revision of ANSI C78.380-2007 (R2010)): 7/7/2016 ANSI C78.62035-2016, Electric Lamps - Discharge Lamps (Excluding Fluorescent Lamps) - Safety Specifications (revision and redesignation of ANSI/IEC C78.62035-2004 (R2009)): 7/7/2016
Project Initiation Notification System (PINS) Standards Action - July 22, 2016 - Page 13 of 38 Pages ANSI Procedures require notification of ANSI by ANSI-accredited standards developers (ASD) of the initiation and scope of activities expected to result in new or revised American National Standards (ANS). Early notification of activity intended to reaffirm or withdraw an ANS and in some instances a PINS related to a national adoption is optional. The mechanism by which such notification is given is referred to as the PINS process. For additional information, see clause 2.4 of the ANSI Essential Requirements: Due Process Requirements for American National Standards. Following is a list of proposed actions and new ANS that have been received recently from ASDs. Please also review the section in Standards Action entitled "American National Standards Maintained Under Continuous Maintenance" for additional or comparable information with regard to standards maintained under the continuous maintenance option. To view information about additional standards for which a PINS has been submitted and to search approved ANS, please visit www.nssn.org, which is a database of standards information. Note that this database is not exhaustive. Directly and materially affected interests wishing to receive more information or to submit comments are requested to contact the standards developer directly within 30 days of the publication of this announcement. ANS (American Nuclear Society) Office: Fax: 555 North Kensington Avenue La Grange Park, IL 60526 Kathryn Murdoch (708) 579-8248 kmurdoch@ans.org BSR/ANS 8.23-201x, Nuclear Criticality Accident Emergency Planning and Response (revision of ANSI/ANS 8.23-2007 (R2012)) Stakeholders: Government and commercial facilities that process or handle significant amounts of fissile material outside reactors and have the potential for a nuclear criticality accident. Project Need: needed to include updated reference for new N13.3 Standard for criticality accident dosimetry, and to address a request for clarification. Other suggestions for improvements will be considered. This standard provides criteria for minimizing risks to personnel during emergency response to a nuclear criticality accident outside reactors. The criteria address management and technical staff responsibilities, planning, equipment, evacuation, rescue, reentry, stabilization, classroom training, drills, and exercises. This standard applies to facilities, locations, or activities judged to have credible and non-trivial consequences from a criticality accident. This standard does not apply to nuclear power plant sites or to licensed research reactor facilities, which are addressed by other standards. BSR/ANS 20.2-201x, Nuclear Safety Design Criteria and Functional Performance Requirements for Liquid-Fuel Molten Salt Reactor Nuclear Power Plants (new standard) Stakeholders: Nuclear facility owners/operators, reactor vendors, plant architect-engineers, constructors, nuclear regulatory authorities, national/international nuclear energy agencies/laboratories, national/local governments, and the public. Project Need: An American National Standard that defines the nuclear safety design criteria for liquid-fuel molten-salt reactor power plants is required to support the development of future nuclear power plants using this technology. This standard establishes the nuclear safety design criteria and functional performance requirements for liquid-fuel molten salt reactor nuclear power plants. The document uses performance-based, riskinformed criteria wherever possible. It also describes the design process to be followed to establish those criteria and perform structures, systems, and component classifications. BSR/ANS 30.2-201x, Categorization and Classification of Structures, Systems, and Components for New Nuclear Power Plants (new standard) Stakeholders: Nuclear power plant designers, architect engineers, plant operators, configuration control engineers, and nuclear industry regulators. Project Need: Current risk categorization and safety classification schemes and selection criteria for NPP Structures, Systems, and Components (SSCs) are inconsistent. Future nuclear power plants need a single, technology neutral system for plant and public safety, environmental, and seismic classification of SSCs that includes, where possible, risk informed and performance based criteria. This standard harmonizes several national consensus standards (NCS) and regulatory documents for new nuclear power plants regarding categorization and classification of SSCs and provides special treatment criteria based on SSC classification. This standard is written for new nuclear power plant designs. It may be applied to older nuclear power plant designs. This standard provides a single technology neutral categorization and classification process for SSCs for new nuclear power plants that is risk informed and performance based (RIPB). This process will be used to determine special treatment of SSCs to meet the safety basis. This standard applies only to new design facilities that must obtain an operating license from the proper regulatory authority. It provides a complete repeatable logical process based upon RIPB objectives. Other voluntary consensus standards may often be required in order to complete the entire process for all SSCs. Those standards are incorporated by reference.
Standards Action - July 22, 2016 - Page 14 of 38 Pages ASHRAE (American Society of Heating, Refrigerating and Air- Conditioning Engineers, Inc.) Office: 1791 Tullie Circle, NE Atlanta, GA 30329 Fax: Stephanie Reiniche (678) 539-2159 sreiniche@ashrae.org BSR/ASHRAE Standard 221-201x, Test Method to Measure and Score the Operating Performance of an Installed Constant Volume Unitary HVAC System (new standard) Stakeholders: Consumers, contractors, energy professionals, facility owners, manufacturers, utilities, and regulators. Project Need: The purpose of this proposed standard is to document and standardize an in-field test method to measure and score the performance of an installed constant volume unitary HVAC system, including operating efficiency and capacity. This standard: - Establishes uniform methods of measurements and testing to obtain scoring data; - Specifies test instruments, specifications, and calibration requirements for performing such measurements and tests; - Specifies data required and calculations to be used; and - Applies to single-zone constant volume unitary HVAC systems of any size. ASME (American Society of Mechanical Engineers) Office: Fax: Two Park Avenue New York, NY 10016 Mayra Santiago (212) 591-8501 ansibox@asme.org BSR/ASME B107.4-201x, Driving and Spindle Ends for Portable Hand, Impact, Air, and Electric Tools (Percussion Tools Excluded) (revision and redesignation of ANSI/ASME B107.4M-2005 (R2011)) Stakeholders: Manufacturers, users, distributors. Project Need: Revise the standard to bring it up to date with current business practices and to address errors found in some of the tables. This Standard applies to portable power tools for drilling, grinding, polishing, sawing, and driving threaded fasteners and hand tools for driving threaded fasteners. ASSE (ASC A10) (American Society of Safety Engineers) Office: Fax: 520 N. Northwest Highway Park Ridge, IL 60068 Tim Fisher (847) 296-9221 TFisher@ASSE.org BSR ASSE A10.11-201X, Safety Requirements for Personnel Nets (revision of ANSI ASSE A10.11-2010) Stakeholders: Construction and demolition safety and health professionals. Project Need: Based upon the consensus of the ANSI/ASSE A10 ASC and leadership of the ASSE. Establishes safety requirements for the selection, installation, and use of personnel and debris nets during construction, repair, and demolition operations. * ASTM (ASTM International) Office: Fax: 100 Barr Harbor Drive West Conshohocken, PA 19428-2959 Corice Leonard (610) 834-3683 accreditation@astm.org BSR/ASTM WK55216-201x, New Specification for Standard Specification for Polyethylene (PE) Branch Saddle Tees (new standard) Stakeholders: Fittings industry. Project Need: These types of fittings are widely used within multiple industry segments. However, there is significant variability in design, construction, and performance. http://www.astm.org/database.cart/workitems/wk55216.htm ATIS (Alliance for Telecommunications Industry Solutions) Office: 1200 G Street NW Suite 500 Washington, DC 20005 Alexandra Blasgen ablasgen@atis.org BSR/ATIS 0300003-201x, XML Schema Interface for Fault Management (Trouble Administration) (revision of ANSI/ATIS 0300003-2015) Stakeholders: Communications industry. Project Need: To incorporate ATIS 0300228.2011 into ATIS 0300003 as an Informative Annex. This standard provides an XML schema information model for Trouble Administration and an XML schema interface for Trouble Administration functions and services. NEMA (ASC C18) (National Electrical Manufacturers Association) Office: Fax: 1300 North 17th Street Suite 900 Rosslyn, VA 22209 Khaled Masri (703) 841-3367 khaled.masri@nema.org BSR C18.2M, Part 1-201x, Standard for Portable Rechargeable Cells and Batteries - General and Specifications (revision of ANSI C18.2M, Part 1-2013) Stakeholders: Manfacturers, general interest, users, and testing aboratories of Portable Rechargeable Cells and Batteries Project Need: Update technical specification sheets. This publication applies to portable rechargeable, or secondary, cells and batteries based on the following electrochemical systems: (a) Nickel-cadmium, (b) Nickel-metal hydride, and (c) Lithium-ion including lithium ion polymer. Section 1 of this standard contains general information and all standardized performance and mechanical tests upon which all the specifications in Section 2 are based. Section 2 specification sheets list those tests and requirements described in this standard that are required for each battery. Not all tests in Section 1 are necessarily required on every specification sheet. Part 2 of this standard describes all safety tests and requirements.
Standards Action - July 22, 2016 - Page 15 of 38 Pages NEMA (ASC Z535) (National Electrical Manufacturers Association) Office: 1300 North 17th Street Arlington, VA 22209 Kevin Connelly Kevin.Connelly@Nema.org BSR Z535.1-201x, Standard on Safety Colors (revision of ANSI Z535.1-2006 (R2011)) Stakeholders: Periodic review of ANSI Z535.1. Project Need: Standard 5-year ANSI affirmation. This standard sets forth the technical definitions, color standards, and color tolerances for safety colors. SDI (ASC A250) (Steel Door Institute) Office: Fax: 30200 Detroit Road Westlake, OH 44145 Linda Hamill (440) 892-1404 leh@wherryassoc.com BSR A250.3-201x, Test Procedure and Acceptance Criteria for Factory Applied Finish Coatings for Steel Doors and Frames (revision of ANSI A250.3-2007 (R2011)) Stakeholders: Steel door manufacturers and users. Project Need: To satisfy the 5-year review cycle. These methods prescribe the procedures to be followed in the selection of material, chemical preparation, coating application, testing, and evaluation of factory applied finish coatings of steel doors and frames. BSR A250.4-201x, Test Procedure and Acceptance Criteria for Physical Endurance for Steel Doors, Frames, and Frame Anchors (revision of ANSI A250.4-2011) Stakeholders: Steel door manufacturers and users. Project Need: To satisfy the 5-year review cycle. The primary purpose of this procedure shall be to establish a standard method of testing the performance of a steel door mounted in a hollow metal or channel iron frame installed with appropriate anchors, under conditions that might reasonably be considered an accelerated field operating condition. BSR A250.10-201x, Test Procedure and Acceptance Criteria for Prime Painted Steel Surfaces for Steel Doors and Frames (revision of ANSI A250.10-2011) Stakeholders: Steel door manufacturers and users. Project Need: To satisfy the 5-year review cycle. These methods prescribe the procedures to be followed in the selection of material, chemical preparation, painting, testing, and evaluation of prime painted steel surfaces for steel doors and frames. * TIA (Telecommunications Industry Association) Office: Fax: 1320 North Courthouse Road Suite 200 Arlington, VA 22201 Teesha Jenkins (703) 907-7727 standards@tiaonline.org BSR/TIA 604-18-A-201x, FOCIS 18 - Fiber Optic Connector Intermateability Standard Type MPO-16 (revision and redesignation of ANSI/TIA 604-18-2015) Stakeholders: Manufacturers and users of fiber optics cables. Project Need: Provide updates for an existing standard. The project will revise the existing FOCIS-18 standard to add anglepolished plugs, both up-angle and down-angle, and active device receptacles, one that mates to non-angled plugs and another that mates to down-angled plugs, for ferrules with one fiber row and two fiber rows. UL (Underwriters Laboratories, Inc.) Office: 12 Laboratory Drive Research Triangle Park, NC 27709-3995 Casey Granata Casey.Granata@UL.Com BSR/UL 508A-201x, Standard for Safety for Industrial Control Panels (new standard) Stakeholders: AHJs, insurance companies, producers of industrial control panels, producers of components of industrial control panels, electricians, and building owners. Project Need: Industrial control panels are widely used throughout the United States. UL 508A is already recognized as the standard covering these products in the United States. Therefore, UL 508A should be recognized as an ANSI-approved US National Standard. These requirements cover industrial control panels intended for general industrial use, operating from a voltage of 600 volts or less. This equipment is intended for installation in ordinary locations, in accordance with the National Electrical Code, ANSI/NFPA 70, where the ambient temperature does not exceed 40 C (104 F) maximum. UL (Underwriters Laboratories, Inc.) Office: 333 Pfingsten Road Northbrook, Illinois 60062 Megan Monsen megan.monsen@ul.com BSR/UL 2995-201x, Standard for Safety for Lifts for Swimming Pools and Spas (new standard) Stakeholders: Manufacturers of lifts, consumers, and AHJs. Project Need: Development of new American National Standard. The standard is intended to address electrically operated lifts intended to allow handicapped persons to enter and exit in-ground swimming pools and spas.
Standards Action - July 22, 2016 - Page 16 of 38 Pages American National Standards Maintained Under Continuous Maintenance The ANSI Essential Requirements: Due Process Requirements for American National Standards provides two options for the maintenance of American National Standards (ANS): periodic maintenance (see clause 4.7.1) and continuous maintenance (see clause 4.7.2). Continuous maintenance is defined as follows: The standard shall be maintained by an accredited standards developer. A documented program for periodic publication of revisions shall be established by the standards developer. Processing of these revisions shall be in accordance with these procedures. The published standard shall include a clear statement of the intent to consider requests for change and information on the submittal of such requests. Procedures shall be established for timely, documented consensus action on each request for change and no portion of the standard shall be excluded from the revision process. In the event that no revisions are issued for a period of four years, action to reaffirm or withdraw the standard shall be taken in accordance with the procedures contained in the ANSI Essential Requirements. The Executive Standards Council (ExSC) has determined that for standards maintained under the Continuous Maintenance option, separate PINS announcements are not required. The following ANSI Accredited Standards Developers have formally registered standards under the Continuous Maintenance option. - AAMI (Association for the Advancement of Medical Instrumentation) - AAMVA (American Association of Motor Vehicle Administrators) - AGA (American Gas Association) - AGSC (Auto Glass Safety Council) - ASC X9 (Accredited Standards Committee X9, Incorporated) - ASHRAE (American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.) - ASME (American Society of Mechanical Engineers) - ASTM (ASTM International) - GBI (The Green Building Initiative) - GEIA (Greenguard Environmental Institute) - HL7 (Health Level Seven) - IESNA (The Illuminating Engineering Society of North America) - MHI (ASC MH10) (Material Handling Industry) - NAHBRC (NAHB Research Center, Inc.) - NBBPVI (National Board of Boiler and Pressure Vessel Inspectors) - NCPDP (National Council for Prescription Drug Programs) - NISO (National Information Standards Organization) - NSF (NSF International) - PRCA (Professional Ropes Course Association) - RESNET (Residential Energy Services Network) - TIA (Telecommunications Industry Association) - UL (Underwriters Laboratories, Inc.) To obtain additional information with regard to these standards, including contact information at the ANSI Accredited Standards Developer, please visit ANSI Online at www.ansi.org/asd, select Standards Activities, click on Public Review and Comment and American National Standards Maintained Under Continuous Maintenance. This information is also available directly at www.ansi.org/publicreview. Alternatively, you may contact the Procedures & Standards Administration department (PSA) at psa@ansi.org or via fax at 212-840-2298. If you request that information be provided via E-mail, please include your E-mail address; if you request that information be provided via fax, please include your fax number. Thank you.
Standards Action - July 22, 2016 - Page 17 of 38 Pages ANSI-Accredited Standards Developers Contact Information The addresses listed in this section are to be used in conjunction with standards listed in PINS, Call for Comment and Final Actions. This section is a list of developers who have submitted standards for this issue of Standards Action it is not intended to be a list of all ANSI-Accredited Standards Developers. Please send all address corrections to Standards Action Editor at standact@ansi.org. AAMI Association for the Advancement of Medical Instrumentation 4301 N Fairfax Drive Suite 301 Arlington, VA 22203-1633 Phone: (703) 647-2779 Web: www.aami.org AHRI Air-Conditioning, Heating, and Refrigeration Institute 2111 Wilson Boulevard Suite 500 Arlington, VA 22201 Phone: (703) 600-0327 Fax: (703) 562-1942 Web: www.ahrinet.org AISC American Institute of Steel Construction One East Wacker Drive Suite 700 Chicago, IL 60601 Phone: (312) 670-5410 Fax: (312) 986-9022 Web: www.aisc.org ANS American Nuclear Society 555 North Kensington Avenue La Grange Park, IL 60526 Phone: (708) 579-8268 Fax: (708) 579-8248 Web: www.ans.org APCO Association of Public-Safety Communications Officials- International 351 N. Williamson Boulevard Daytona Beach, FL 32114-1112 Phone: (386) 322-2500 Fax: (386) 944-2794 Web: www.apcointl.org ASCE American Society of Civil Engineers 1801 Alexander Bell Dr Reston, VA 20191 Phone: 703-295-6176 Web: www.asce.org ASHRAE American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc. 1791 Tullie Circle, NE Atlanta, GA 30329 Phone: (678) 539-1143 Fax: (678) 539-2159 Web: www.ashrae.org ASME American Society of Mechanical Engineers Two Park Avenue New York, NY 10016 Phone: (212) 591-8521 Fax: (212) 591-8501 Web: www.asme.org ASSE (Safety) American Society of Safety Engineers 520 N. Northwest Highway Park Ridge, IL 60068 Phone: (847) 768-3411 Fax: (847) 296-9221 Web: www.asse.org ASTM ASTM International 100 Barr Harbor Drive West Conshohocken, PA 19428-2959 Phone: (610) 832-9744 Fax: (610) 834-3683 Web: www.astm.org ATIS Alliance for Telecommunications Industry Solutions 1200 G Street NW Suite 500 Washington, DC 20005 Phone: (202) 434-8840 Web: www.atis.org CSA CSA Group 8501 East Pleasant Valley Rd. Cleveland, OH 44131 Phone: (216) 524-4990 x88321 Fax: (216) 520-8979 Web: www.csa-america.org FCI Fluid Controls Institute 1300 Sumner Avenue Cleveland, OH 44115 Phone: (216) 241-7333 Fax: (216) 241-0105 Web: www.fluidcontrolsinstitute.org ITI (INCITS) InterNational Committee for Information Technology Standards 1101 K Street NW Suite 610 Washington, DC 20005-3922 Phone: (202) 626-5741 Fax: 202-638-4922 Web: www.incits.org NEBB National Environmental Balancing Bureau 8575 Grovemont Circle Gaithersburg, MD 20877 Phone: (301) 591-0484 Web: www.nebb.org NEMA (ASC C12) National Electrical Manufacturers Association 1300 North 17th Street Suite 900 Rosslyn, VA 22209 Phone: (703) 841-3278 Fax: (703) 841-3367 Web: www.nema.org NEMA (ASC C78) National Electrical Manufacturers Association 1300 N 17th St Rosslyn, VA 22209 Phone: 703-841-3262 Web: www.nema.org NEMA (ASC C8) National Electrical Manufacturers Association 1300 North 17th Street Rosslyn, VA 22209 Phone: (703) 841-3299 Web: www.nema.org NEMA (Canvass) National Electrical Manufacturers Association 1300 North 17th Street Arlington, VA 22209 Phone: (703) 841-3299 Web: www.nema.org NSF NSF International 789 N. Dixboro Road Ann Arbor, MI 48105-9723 Phone: (734) 769-5197 Web: www.nsf.org OEOSC (ASC OP) Optics and Electro-Optics Standards Council POB 24773 Rochester, NY 14624 Phone: (585) 473-4470 Web: www.optstd.org SCTE Society of Cable Telecommunications Engineers 140 Philips Road Exton, PA 19341-1318 Phone: (480) 252-2330 Fax: (610) 363-5898 Web: www.scte.org SDI (ASC A250) Steel Door Institute 30200 Detroit Road Westlake, OH 44145 Phone: (440) 899-0010 Fax: (440) 892-1404 Web: www.wherryassocsteeldoor.org TIA Telecommunications Industry Association 1320 North Courthouse Road Suite 200 Arlington, VA 22201 Phone: (703) 907-7706 Fax: (703) 907-7727 Web: www.tiaonline.org UL Underwriters Laboratories, Inc. 333 Pfingsten Road Northbrook, Illinois 60062 Phone: (847) 664-1292 Web: www.ul.com
Standards Action - July 22, 2016 - Page 18 of 38 Pages ISO & IEC Draft International Standards This section lists proposed standards that the International Organization for Standardization (ISO) and the International Electrotechnical Commission (IEC) are considering for approval. The proposals have received substantial support within the technical committees or subcommittees that developed them and are now being circulated to ISO and IEC members for comment and vote. Standards Action readers interested in reviewing and commenting on these documents should order copies from ANSI. Comments Comments regarding ISO documents should be sent to ANSI s ISO Team (isot@ansi.org); those regarding IEC documents should be sent to Tony Zertuche, General Secretary, USNC/IEC, at ANSI's New York offices (tzertuche@ansi.org). The final date for offering comments is listed after each draft. Ordering Instructions ISO and IEC Drafts can be made available by contacting ANSI s Customer Service department. Please e-mail your request for an ISO or IEC Draft to Customer Service at sales@ansi.org. When making your request, please provide the date of the Standards Action issue in which the draft document you are requesting appears. ISO Standards AGRICULTURAL FOOD PRODUCTS (TC 34) ISO/DIS 18794, Coffee - Sensorial analysis - Vocabulary - 8/7/2016, FREE ISO/DIS 34101-1, Sustainable and traceable cocoa beans - Part 1: Requirements for sustainability management systems - 10/5/2016, $112.00 ISO/DIS 34101-2, Sustainable and traceable cocoa beans - Part 2: Requirements for performance (related to economic, social, and environmental aspects) - 10/5/2016, $67.00 ISO/DIS 34101-3, Sustainable and traceable cocoa beans - Part 3: Requirements for traceability - 10/5/2016, $82.00 AIRCRAFT AND SPACE VEHICLES (TC 20) ISO/DIS 19923, Space environment (natural and artificial) - Plasma environments for generation of worst case electrical potential differences for spacecraft - 8/7/2016, $67.00 ISO/DIS 8625-2, Aerospace - Fluid systems - Vocabulary - Part 2: General terms and definitions relating to flow - 8/7/2016, $33.00 ISO/DIS 8625-3, Aerospace - Fluid systems - Vocabulary - Part 3: General terms and definitions relating to temperature - 8/7/2016, $33.00 EARTH-MOVING MACHINERY (TC 127) ISO/DIS 17757, Earth-moving machinery and mining - Autonomous and semi-autonomous machine system safety - 10/7/2016, $107.00 FIRE SAFETY (TC 92) ISO/DIS 19703, Generation and analysis of toxic gases in fire - Calculation of species yields, equivalence ratios and combustion efficiency in experimental fires - 8/7/2016, $107.00 FLUID POWER SYSTEMS (TC 131) ISO/DIS 5782-1, Pneumatic fluid power - Compressed-air filters - Part 1: Main characteristics to be included in suppliers literature and product marking requirements - 8/7/2016, $53.00 ISO/DIS 8434-1, Metallic tube connections for fluid power and general use - Part 1: 24 cone connectors [revision of ISO 8434-1:2007] - 10/2/2016, $125.00 GEOSYNTHETICS (TC 221) ISO/DIS 13438, Geotextiles and geotextile-related products - Screening test method for determining the resistance to oxidation - 10/6/2016, $46.00 GRAPHIC TECHNOLOGY (TC 130) ISO/DIS 16613-1, Graphic technology - Variable content replacement - Part 1: Using PDF/X for variable content replacement (PDF/VCR-1) - 10/2/2016, $93.00 HYDROMETRIC DETERMINATIONS (TC 113) ISO 4359/DAmd1, Flow measurement structures - Rectangular, trapezoidal and U-shaped flumes - Amendment 1-8/4/2016, $29.00 MATERIALS, EQUIPMENT AND OFFSHORE STRUCTURES FOR PETROLEUM AND NATURAL GAS INDUSTRIES (TC 67) ISO/DIS 13623, Petroleum and natural gas industries - Pipeline transportation systems - 8/4/2016, FREE ISO/DIS 35101, Petroleum and natural gas industries - Arctic operations - Working environment - 10/5/2016, $119.00 MECHANICAL TESTING OF METALS (TC 164) ISO/DIS 6507-1, Metallic materials - Vickers hardness test - Part 1: Test method - 8/4/2016, $93.00 ISO/DIS 6507-2, Metallic materials - Vickers hardness test - Part 2: Verification and calibration of testing machines - 8/4/2016, $77.00 ISO/DIS 6507-3, Metallic materials - Vickers hardness test - Part 3: Calibration of reference blocks - 8/4/2016, $62.00 ISO/DIS 6507-4, Metallic materials - Vickers hardness test - Part 4: Tables of hardness values - 8/4/2016, $146.00 MECHANICAL VIBRATION AND SHOCK (TC 108) ISO 7919-3/DAmd1, Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 3: Coupled industrial machines - Amendment 1-10/2/2016, $33.00 ISO 7919-4/DAmd1, Mechanical vibration - Evaluation of machine vibration by measurements on rotating shafts - Part 4: Gas turbine sets with fluid-film bearings - Amendment 1-10/2/2016, $40.00