DIVISION 11: NUTRITION SERVICES DESIGN STANDARDS APPENDIX A: EQUIPMENT LIST Table of Contents I. Name Brand Specification, Only A. Combi Oven Blodgett B. Crowd Control BSI Classic Beltway C. Milk Cooler Carrier Beverage-Air D. Condiment Bar Cambro E. Salad Bar Cambro F. Hot Cabinet Metro G. Merchandiser Hatco H. Point of Sale Cart Cambro I. Tray and Dish Cart Cambro J. Ware Washer Hobart K. Waste Disposal Red Goat
II. Preferred Products A. Cooktop Lang Electric B. Microwave Oven Panasonic C. Can Opener Edlund D. Reach-in Cooler Traulsen Hoshizaki E. Reach-in Freezer Traulsen Hoshizaki F. Shelving (Walk-in Refrigerators and Freezers) Metro G. Jacketed Kettle and Stand Cleveland Range Groen H. Bun Racks Metro Moblie I. Three Tier Cart Cambro Rubbermaid J. Booster Heater (Warewasher) Precision Temp Vanguard Technology Hobart?? BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 2 of 15
DIVISION 11: NUTRITION SERVICES DESIGN STANDARDS PRODUCT FINDINGS I. NAME BRAND SPECIFICATION Operating under charter from the Beaverton School District s Construction Design Standards Quality Management Board, the Nutrition Services Functional Team has developed the Beaverton School District s Nutrition Services Design Standard. The functional team determined that it was important for the District to standardize on the use of certain products. These products are called out by name brand as part of the Standard. Nutrition Services, though a department of Beaverton School District, operates as a franchise to deliver quality, nutritious, and affordable meals to students throughout the District. Serving fifty separate sites, it is very important to have all kitchens set up in a similar manner. There are different requirements for elementary schools, middle schools, and high schools serving lines and kitchen equipment. Equipment standardization by school type increases staffing flexibility. Staff training requirements are reduced when all similar sites use the same equipment, and staff can work at any site with minimal need for additional training. Durability, reliability, and parts availability are of critical importance in a commercial kitchen environment. Standardization provides both a means of describing the quality of product and provides additional value to the District. The additional value is often found in reduced cost for maintenance and operations. Cost savings result from efficient use of existing stock and supplies, interchangeability of parts, reduced warehousing and stocking requirements, and familiarity with the installation, operation, and maintenance requirements for the product thus requiring no additional training. The specific products will be listed on the following pages, along with findings compliant with the requirements of ORS279C.345(2) and submittal cut sheets for each product. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 3 of 15
A. COMBI OVENS BLODGETT Ovens Double-stack with a Combi (steam/dry air) oven on top and a convection (dry air) oven on the bottom shall be provided in all kitchens. Larger elementary, middle and high schools should be designed for two or more sets of ovens. Electric ovens may be used in remodels when the kitchen does not have gas service. The Combi ovens require a water connection and floor drain. Natural Gas: Electric: BX-14G and DFG-200 with Stacking Kit SK-88FS BX14E and Zephaire-E Plus with Stacking Kit SK-88FS Electric models shall only be used for remodels when natural gas service is not available. Blodgett is the only manufacturer of commercial quality kitchen equipment that offers a boiler-less Combi stacked on a full size convection oven. The Blodgett ovens are highly efficient (Energy Star rated) and have proven to be very reliable and durable. Consistency between sites provides savings to the District in both operations and maintenance. Standardizing on a single model of double stack oven reduces space required for stocking of replacement parts and allows efficient utilization of existing supplies. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 4 of 15
B. CROWD CONTROL CLASSIC BELTWAY BY BSI CROWD CONTROL Crowd Control A minimum of eight crowd control stanchions are required. The total number of stanchions will be determined by the design. Crowd control devices used for Beaverton School District cafeteria serving lines, to make efficient use of existing materials and supplies, shall be fully compatible and interchangeable with Classic Beltway by BSI Crowd Control. The Classic Beltway has proven to be a safe, convenient, and reliable product. The replaceable belt cassette simplifies maintenance and allows the District to stock a supply of repair parts. Standardization allows the District to interchange pieces between sites when conditions vary or student populations shift. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 5 of 15
C. MILK COOLERS CARRIER BEVERAGE-AIR SCHOOL MILK COOLERS Cold Storage Typical kitchen shall have a walk-in freezer, a walk-in cooler, a reach-in cooler, and a 16-crate milk cooler located in the serving area with space for an optional 8-crate milk cooler included in the design. Size, model and number of milk coolers are based on number of lunches served. If greater than 400 lunches are served daily, two 16-crate milk coolers are required. Separate electrical receptacles shall be provided for separate milk cooler and HVAC shall be sized to handle the additional heat load. SMF34 SMF49 SMF58 The Carrier Beverage-Air SMF School Milk coolers are the only product of acceptable quality. These coolers were specifically designed for use in school food service lines. They have a patented forced air system to create a continuous cold air blanket over the milk keeping it cold even when the lid is open for long serving periods. The cases are heavy duty with 2 thick polyurethane insulation and reinforced floors. These milk coolers have proven to be very reliable and are designed for ease of service. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 6 of 15
D. CONDIMENT BAR & SALAD BAR CAMBRO MANUFACTURING COMPANY Condiment Bars The condiment bar for schools usually consists of one 6 condiment bar with trays rails and end tables. Height of legs will be determined by site. Elementary schools require child height legs. The need for condiment bars at middle and high schools will be determined by design. Elementary Schools: 6FBRSL with End Tables (2) and Tray Rails (2), Black Salad Bars The salad bars for elementary (ES) and middle (MS) schools usually consist of two 5 (ES) or two 6 (MS) mobile salad bars with sneeze guards, trays rails, and end tables. Height of legs will be determined by site. Elementary schools require child height legs. Middle schools require regular (tall) legs. Schools serving larger numbers of students or multiple grade levels (K-8) may require salad bar units with both regular and short leg heights. Elementary Schools: 5FBRSL with Sneeze Guard, End Table (1) and Tray Rails (1), Black Middle & High Schools: 5FBR with Sneeze Guard, End Table (1) and Tray Rails (1), Black The Cambro Manufacturing food bars are the only product of acceptable quality, no other manufacturer offers comparable equipment for the price. The Cambro food bars can be reconfigured to meet each sites needs. Parts are readily available and many of the components are interchangeable. Standardizing on this product, besides providing substantial savings to the District, also provides the additional advantage of consistency between sites simplifying training and allowing more flexibility in operations. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 7 of 15
E. HOT CABINET METRO Hot Cabinets A minimum of two hot cabinets are required in each kitchen, dependent on the size of the schools and expected participation. Metro C5 3 Series Metro Hot Cabinets have proven to be cost effective, durable and reliable. The Metro C5 3 Series is Energy Star rated providing Substantial savings, both in first cost and in operations. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 8 of 15
F. MERCHANDISER HATCO GLO-RAY GR2SDS No comparable product. Hatco GR2SDS merchandisers provide reliability, durability and consistency between sites. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 9 of 15
G. POINT of SALE CART CAMBRO Point of Sale (POS) Provide data and electric at each POS. Point of Sale system shall be provided by Nutrition Services. CAMBRO ES28RL, Black Substantial savings. Cambro POS carts are less expensive than custom mobile carts, more durable, provide better mobility, and are interchangeable between sites. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 10 of 15
H. TRAY AND DISH CART CAMBRO No comparable product. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 11 of 15
I. WAREWASHER HOBART Kitchen Dishwashers Design and plumb for high temperature, single tank, conveyor machines. Maximum rated water use shall not exceed 128 gallons per hour during continuous use. Preferred model: Hobart CL44e with Opti-rinse. Hobart CL44e Hobart C-Line 44A No comparable product. Hobart dishwashers have proven to be cost effective and very reliable. Energy Star rated, lowest water and energy use per rack of any commercial ware washer. Consistency between sites provides familiarity for both operations and maintenance, and allows stocking of replacement parts for maintenance BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 12 of 15
J. COMMERCIAL GARBAGE DISPOSALS RED GOAT DISPOSERS Garbage Disposals Kitchen: Use Red Goat only. Staff room and other applications: ½ HP minimum ISE Badger 5. Red Goat Disposers are dominant throughout the food service industry because they are the only manufacturer of a garbage disposal product to provide the quality, reliable service, and the ease of maintenance required in a commercial kitchen application. The Red Goat disposers have a large throat opening and a large diameter rotor. Both of these features minimize the amount of downtime and the amount of time required for maintenance. Red Goat disposers are the only disposers on the market that can be fully rebuilt. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 13 of 15
II. PREFERRED PRODUCTS Products listed as preferred products shall be used as Basis of Design on Beaverton School District projects even if they are not specifically called out in the Standards. Many of these products are called out in the Standards as a name brand product or equal. The intent of calling products out as name brand or equal is to provide a basis of design and to establish a required level of quality. The burden falls on the supplier or Contractor to show that a product is equal. The Contracting Agency shall determine, in its sole discretion, whether an Offeror's alternate product is "equal" or "equivalent." Manufacturer s cut sheets have been provided for the preferred products. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 14 of 15
A. COOKTOP Lang Electric 36S-14 B. MICROWAVE OVEN Panasonic 1257 or 2157 C. REACH-IN COOLER Traulsen Hoshizaki D. REACH-IN FREEZER Traulsen Hoshizaki E. SHELVING (Walk-in Refrigerators and Freezers) Metro F. JACKETED KETTLE and STAND Cleveland Range: Electric: KET-12-T Gas: KGT-12-T Stand: ST28 Groen G. BUN RACKS Metro Mobile H. THREE TIER CART CAMBRO Rubbermaid I. BOOSTER HEATER Precision Temp PT-200 Vanguard Technology PM-200N Hobart J. CAN OPENER Edlund Can openers provide consistency between sites; repair parts are readily available. BSD Division 11: Nutrition Services Design Standards Appendix A: Equipment List Page 15 of 15
BX-14G and DFG-200 BX-14G Boilerless Combi Stacked on a Full-Size Gas Convection Oven Shown with optional casters DFG-200 OPTIONS AND ACCESSORIES (AT ADDITIONAL CHARGE) Gas hose with quick disconnect and restraining device: 48" (1219mm) hose 36" (914mm) hose Solid state digital control with LED display, cook and hold, and Pulse Plus Stainless steel oven liner 6" (152mm) casters Extra oven racks Stainless steel solid back panel Prison package (inlcudes security control panel and stainless steel back) Security control panel Flue connector OPTIONS AND ACCESSORIES (AT NO ADDITIONAL CHARGE) Solid stainless steel doors Project Item No. Quantity Requires Blodgett stacking kit SK-88FS. DFG-200 SPECIFICATIONS EXTERIOR CONSTRUCTION Full angle-iron frame Stainless steel front, top, and sides Dual pane thermal glass windows encased in stainless steel door frames Porcelain door handle with simultaneous door operation Triple-mounted pressure lock door design with turnbuckle assembly Modular slide out front control panel for easy access Solid mineral fiber insulation at top, back, sides and bottom INTERIOR CONSTRUCTION Double-sided porcelainized baking compartment liner (14 gauge) for easy cleaning Aluminized steel combustion chamber Dual inlet blower wheel Five chrome-plated racks, eleven rack positions with a minimum of 1-5/8" (41 mm) spacing OPERATION Dual Flow Gas system combines direct and indirect heat Electronic spark ignition control system Removable dual tube burners Pressure regulator Manual gas service cut-off switch on the front of the control panel Air mixers with adjustable air shutters Solid state thermostat with temperature control range of 200 F (93 C) to 500 F (260 C) Two speed fan motor (60 Hz only, not available in 50 Hz)* 1/3 horsepower blower motor with automatic thermal overload protection Control area cooling fan Two 50 watt commercial bake oven lamps CAPACITY Extra depth baking compartment - accepts five 18" x 26" standard fullsize baking pans in left-to-right or front-to-back positions. STANDARD FEATURES Solid state manual with separate dials to control thermostat and timer 6" (152mm) adjustable stainless steel legs Two year oven parts and one year labor warranty* Five year limited oven door warranty* * For all international markets, contact your local distributor. BLODGETT OVEN COMPANY www.blodgett.com 44 Lakeside Avenue, Burlington, VT 05401 Toll Free: (800) 331-5842 Phone: (802) 860-3700 Fax: (802) 864-0183 BX-14G STACKED ON A DFG-200
BX-14G and DFG-200 BX-14G Boilerless Combi Stacked on a Full-Size Gas Convection Oven Shown with optional casters BX-14G OPTIONS AND ACCESSORIES (AT ADDITIONAL CHARGE) MenuSelect control can hold multi-stage programming for up to 99 products, includes Cook & Hold and core probe cooking Additional 6-1/2 core temperature probe Additional stainless steel wire shelves Chicken roasting rack Single source water manifold Water pressure regulator (1 per section) Extended warranty OPTIONS AND ACCESSORIES (AT NO CHARGE) LP gas 208/240 volt BX-14G COMBI SPECIFICATIONS EXTERIOR CONSTRUCTION Stainless steel top, front and sides Dual pane tempered viewing window with hinged inner glass for easy cleaning Door mounted condensate trough Top and bottom mount, easily adjustable door hinges Pivot out user interface panel for service access INTERIOR CONSTRUCTION Fully welded stainless steel frame Fully insulated cooking chamber Fixed drain bottom center of cavity Easily removable stainless steel side rails 316 stainless steel coved corner liner for ease of cleaning OPERATION Standard control with function selection for steam, combi, hot air and cool down Retherm band on control Steam on demand feature Thermostat control to 500F Multiple speed reversing fan for even bake Dual stage door latch to vent steam before fully opening door Cavity vent control provides ability to release steam at the turn of a switch Integral door switch Electronic spark ignition Open vented system. Condenses steam and drains away by-products of the cooking process, eliminates flavor transfer CAPACITY Fourteen 12" x 20" x 2-1/2" deep pans at 3-1/4" spacing Seven 18" x 26" deep pans at 3-1/4" spacing STANDARD FEATURES Five (5) stainless steel wire shelves per section (capacity for 7) Hinged pressure panel for cleanability Four halogen lights for superior cavity illumination Retractable hose reel hidden behind door, no extraneous hoses Stacking kit and casters for double stack ovens Pressure spray bottle for oven cleaning 6-1/2 core temperature probe Start-up inspection service by factory authorized service agent One year parts and labor oven warranty* * For all international markets, contact your local distributor. BX-14G STACKED ON A DFG-200 BLODGETT OVEN COMPANY www.blodgett.com 44 Lakeside Avenue, Burlington, VT 05401 Toll Free: (800) 331-5842 Phone: (802) 860-3700 Fax: (802) 864-0183
BX-14G STACKED ON A DFG-200 DIMENSIONS ARE IN INCHES (MM) 69.03 (1753) 41.19 (1021) APPROVAL/STAMP 65 (165) Customer Supplied Drain * 76.06 (1932) overall depth with combi door open 90 46.87* (1190) 39.88 (1013) 0 (0) 3 (76) 32 (813) 0 (0) 38.25 (972) 23.59 (599) 5.84 (148) 3.34 (85) 0 (0) D U F UTILITY CONNECTIONS 5.65 (144) 2.91 (74) 1.56 (40) D 0 (0) U Unfiltered Water - Condensate, cold only F F U Filtered Water - Boiler, hot or cold SHORT FORM SPECIFICATIONS Provide Blodgett model BX-14G boilerless gas combination-oven/steamer stacked on a model DFG-200 full-size convection oven. BX-14G Combi - Unit shall have the ability to cook with pressureless steam (212F), hot air, or combination of steam and hot air (with an operating range 140F to 500F), vario-steaming (operating range 140F to 212F), low temperature cooking and holding, rethermalizing, cool down mode and our Exclusive Steam on Demand steam injection system. Oven capacity to accept 7 ea 18x26 bake pans or 14 ea 12x20x2.5 full size steam table pans with 3-1/4 spacing. Front access service user interface control panel and service diagnosis system. Unit shall be constructed with a fully welded stainless steel frame. Cooking chamber shall be constructed with 316 series with 2B dull stainless steel finish and coved corners. Integrated retractable wash down hose to include front water shut off valve. Unit shall include a four speed, bi-directional fan with vent switch to control humidity in the cooking chamber. Dual pane thermal glass window with 180 degree door swing, two-step safety door-latch with adjustable door hinges, door mounted drip pan. Unit to include a detachable 6-1/2 core temperature probe and four halogen lights. A start-up inspection service will be performed by our factory-authorized agent at no cost to the operator. One-year parts and labor warranty, standard. DFG-200 - Shall have (porcelainized/stainless) steel liner and shall accept five 18" x 26" standard full-size bake pans in left-to-right or front-to-back positions. Stainless steel front, top and sides. Doors shall (be solid stainless steel/have dual pane thermal glass windows) with single porcelain handle and simultaneous operation. Unit shall be gas heated with electronic spark ignition and shall cook by means of a dual-flow system combining direct and indirect heat and a gas shutoff switch on the front of the control panel. Air in baking chamber distributed by dual inlet blower wheel powered by a two-speed, 1/3 HP motor with thermal overload protection. Each chamber shall be fitted with two commercial lamps and five chromeplated removable racks. Control panel shall be recessed with Cook/Cool Down mode selector, solid state (manual/digital) infinite thermostat (200-500 F), and 60 minute timer. Provide options and accessories as indicated. DIMENSIONS: Product clearance 6" from combustible and non-combustible construction. 12 on left side if not on casters. Additional Height: 6" adjustable legs 6-7/8" - 8" (174.6-203.2mm) GAS SUPPLY: BX-14G DFG-200 Connection: 3/4" NPT 3/4" NPT Inlet Pressure: Natural 7.0" W.C. 7.0" W.C. minimum 10.5" W.C. maximum Propane 14.0" W.C. 11.05" W.C. minimum 13.0" W.C. maximum Manifold Pressure: Natural 3.5 W.C. 3.5 W.C. Propane 10.0 W.C. 10.0 W.C. Maximum Input: 65,000 BTU/hr 60,000 BTU/hr WATER SUPPLY (BX-14G only): TDS: < 100 ppm Hardness: 80-120 ppm ph: 7.0-8.0 Chlorides: < 30 ppm 30(min)-50(max) PSI 140 F (60 C) avg. drain temp. 2" drain connection 3/4" garden hose cold water POWER SUPPLY: BX-14G: DFG-200: Both units: 120VAC, 20 amp, Nema 5-20R dedicated receptacle 3-wire, 6 Amp, 115 VAC, 1 phase, 60 Hz. 1/3 H.P., 2 speed motor, 1140 and 1725 RPM 2-wire, 3 Amp, 230VAC CE model, 1 phase, 50 Hz. 1/3 H.P., 1 speed motor, 1425 RPM 6' (1.8m) electric cord set furnished Each unit requires a dedicated circuit. MINIMUM ENTRY CLEARANCE: BX-14G DFG-200 Uncrated 33" (838mm)* 32-1/16" (814mm) Crated 42" (1066.8mm) 37-1/2" (953mm) * after adjustment of flue brackets SHIPPING INFORMATION: Approx. Weight: BX-14G 595 lbs. (270 kg) DFG-200 650 lbs. (295 kg) Crate sizes (per section): BX-14G 44.5" H x 42" W x 54.25" D (1130 x 1067 x 1378mm) DFG-200 37-1/2" (952mm) x 43-1/2" (1105mm) x 52" (1321mm) NOTE: The company reserves the right to make substitutions of components without prior notice BLODGETT OVEN COMPANY www.blodgett.com 44 Lakeside Avenue, Burlington, VT 05401 Toll Free: (800) 331-5842 Phone: (802) 860-3700 Fax: (802) 864-0183 Printed in U.S.A. NOTE: FOR COMMERCIAL USE ONLY P/N 51057 Rev C (4/08)
Classic Beltway TM by BSI Crowd Control Guidance Control Barrier CONVENIENT Beltway is designed to connect to and upgrade other systems. You can connect to the post from four directions. We also provide signs that easily attach to the top of the post. SAFE Beltlock helps prevent accidents. It automatically locks the belt to the post preventing accidental disconnection, yet it releases with one hand in compliance with fire codes. Safebelt is engineered to fall to the floor and then slowly retract when released. DURABLE Rubber trimmed base protects the floor. Heavy base and small footprint provide stability while reducing wear and tear on both the post and the public. 18 steel liner connects the post to the base to prevent loosening and tilting. 930/38/38-96 Wrinkle Black w/ Black Belt Specifications 4 way connection Automatic Beltlock 7'6 replaceable belt cassette Rubberized, non-marking base Nylon grommet to protect belt from fraying Small footprint with 12 base 18 steel liner prevents loosening and tilting Sturdiest post on the market at 32 pounds BSI Crowd Control LLC www.bsi-cc.com 877-842-4184
SMF34 SMF58 Made in USA http://www.beverage-air.com http://ccr.carrier.com
ECPC-135451-4/03
Item No. Food Bars Children's Models 6FBRSL - 6 ft. (182 cm), 5FBRSL - 5 ft. (162 cm) 4FBRSL - 4 ft. (130 cm) Features & Benefits Versatility, style and durability for self-service breakfast, lunch or dinner. Accommodates GN 1/1 Full or Fractional Size Food Pans up to 6" (15 cm) deep with Divider Bars. Serving height is just 28" (71 cm) from the floor, perfect for children. Double-wall polyethylene construction provides extra strength, durability and reliability. Scratch-resistant textured exterior. Simple to clean - just wipe off. Thick foamed-in-place polyurethane insulation maintains food temperatures and holds ice cold for hours. Provides added structural strength. NSF listed threaded faucet drain with a standard hose hook-up provides quick draining and cleaning. Four each 5 (12,7 cm) swivel casters w/ brakes ensure easy maneuvering. Standard accessories include protective Sneeze Guard panel made from NSF listed material. Optional accessories include Tray Rails, End Tables, Divider Bars, Crock Holder, and Salad Bowl Holders. Non-electrical. Easy to assemble. Available in 15 colors. Specifier Identification No. Model No. Quantity Optional End Table FBRTBL 5FBRSL (Shown with optional End Tables and Tray Rail) 6 ft. (182 cm) model holds 1 each Salad Bowl Holder (SBH18 or SBH15) and 3 each Crock Holders (CPH3) 5 ft. (162 cm) model holds 1 each Salad Bowl Holder (SBH18 or SBH15) and 2 each Crock Holders (CPH3) 4 ft. (130 cm) model holds 1 each Salad Bowl Holder (SBH18 or SBH15) and 1 each Crock Holder (CPH3) SBH18 Salad Bowls and Crocks Set Up Guide for Children's Food Bars C P H 3 C P H 3 C P H 3 Food Pans 6 ft. (182 cm) model holds 5 each GN 1/1 Full or holds Fractional Size Food Pans with DIV12 and DIV20 Divider Bars 5 ft. (162 cm) model holds 4 each GN 1/1 Full or holds Fractional Size Food Pans with DIV12 and DIV20 Divider Bars 4 ft. (130 cm) models hold 3 GN 1/1 Full or holds Fractional Size Food Pans with DIV12 and DIV20 Divider Bars 1/1 1/1 1/1 1/1 1/1 GN 1/1 Full Size Food Pans DIV20 20 7 /8" (53 cm) Divider Bar SBH15 C P H 3 C P H 3 C P H 3 1 / 2 l o n g 1 / 2 l o n g 1 / 2 1 / 4 1 / 4 1 / 3 1 / 3 1 / 6 1 / 6 1 / 6 1 / 6 GN Fractional Size Food Pans SBH18 - Holds 1 each 18 (45,7 cm) Salad Bowl SBH15 - Holds 1 each 15 (38 cm) Salad Bowl & 3 each 1.5 qt. (1,4 L) or 2.7 qt. (2, 4 L) Crocks CPH3 - Holds 3 each 1.5 qt. (1,4 L) or 2.7 qt. (2, 4 L) Crocks 1 / 2 1 / 4 1 / 4 1 / 3 Approvals 1 / 6 1 / 6 DIV12 12 3 /4" (32,5 cm) Divider Bar 2002 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056-U.S.A. T e l e p h o n e (1)714 848 1555 Toll Free 800 854 7631 Customer Service Hot Line 800 833 3003 LIT FCST-0102-72 72
Food Bars Children's Models 6FBRSL - 6 ft. (182 cm), 5FBRSL - 5 ft. (162 cm) 4FBRSL - 4 ft. (130 cm) Item No. Specifier Identification No. Model No. Quantity 6FBRSL 5FBRSL 4FBRSL Specifications Dimension Tolerance: +/- 1 /4" (0,64 cm) GN 1/1 Full Size Exterior Dimensions Case lbs./cube Code Description Food Pan Capacity L x W x H Kg/m 3 6FBRSL 6 ft. (182 cm) Children's Food Bar 5 71 7 16" x 32 3 4" x 45 3 4" 145 (28.56) (181 x 83 x 116 cm) 66 (0,8) 5FBRSL 5 ft. (162 cm) Children's Food Bar 4 63 7 8" x 32 3 4" x 45 3 4" 131 (25.62) (162 x 83 x 116 cm) 59,5 (0,72) 4FBRSL 4 ft. (130 cm) Children's Food Bar 3 51" x 32 3 4" x 45 3 4" 116 (25.62) (130 x 83 x 116 cm) 53 (0,72) Optional Accessories Tray Rails FBR6R (6 ft.) (182 cm) FBR5R (5 ft.) (162 cm) FBR4R (4 ft.) (130 cm) End Tables FBRTBL 3-Crock Holder CPH3 (holds 1.5 qt. (1,4 L) and 2.7 qt. (2,4 L) crocks) Salad Bowl Holders SBH15 (holds one 15" (38 cm) bowl, 3 crocks) SBH18 (holds one 18" (46 cm) bowl) Divider Bars DIV12 DIV20 Architect Specs The non-electrical portable foodservice Food Bar shall be a Floor Model Children s Food Bar, Model..., manufactured by Cambro Mfg. Co., Huntington Beach, CA 92648 U.S.A. It shall be made of double-wall polyethylene and foam-injected polyurethane insulation. It shall have a 28 (71 cm) working height from the floor to the top of the food wells. It shall have 4 each 5 (12,7 cm) swivel casters with brakes. It shall hold optional accessories such as the Cambro Salad Bowl Holders (SBH18 and SBH15) and Crock Holders (CPH3) or a selection of GN Full or Fractional Size Food Pans with Divider Standard Colors Black (110) Slate Blue (401) Brick Red (402) Coffee Beige (157) Dark Brown (131) Cold Blue (159) Navy Blue (186) Dusty Rose (400) Gray (180) Green (519) Hot Red (158) Granite Gray (191) Granite Green (192) Granite Red (193) Granite Sand (194) Divider Bar: White (148) Clear (035) Crock Holder and Salad Bowl Holder: White (148) Bars. The depth of the interior food wells shall be 6 1 /2 (16,5 cm). It shall be available with optional end tables and side tray rails. It shall include a sneeze guard and protective end panels. It shall have an NSF Listed threaded faucet drain with a standard hose hook up. It shall be available in 15 colors. Approvals 2002 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056-U.S.A. T e l e p h o n e (1)714 848 1555 Toll Free 800 854 7631 Customer Service Hot Line 800 833 3003 Printed in USA
Item # TM Job Metro C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets Insulation Armour : Patented insulation technology retains heat, saves energy, and provides a cool-to-touch exterior. Durable polymer construction is dent, impact, and stain resistant. Molded-in hand holds create vertical handles for mobile applications. Colors: Insulation Armour is available in Red, Blue, or Gray standard and in other colors on a promotional basis or upon request. Control: Four holding modules are available: Holding, Moisture, Proofing, and Combination Proof and Hold. All feature an easy-to-read digital thermometer, recessed control dials, a master on/off switch, and power indicator lights. Performance: All modules provide fast heat-up and recovery through a thermostatically controlled, forced convection system. Sizes: C5 3 Series cabinets are available in Full Height (71", 1803mm), 3 /4 Height (59", 1499mm), and 1 /2 Height (44", 1118mm) sizes. Doors: Solid insulated aluminum or clear polycarbonate doors are available. Full Height cabinets can be configured with full length or Dutch-style doors. Clear doors provide visibility of the contents of the cabinet without the heat loss associated with opening the door. Capacity: Three slide styles provide maximum holding capacity. Choose from Universal Wire, Lip Load, or Fixed Wire. Removable Module: All modules are removable, without tools, for easy cleaning of the cabinet interior. Future module upgrades or changes can occur without cabinet body replacement. Reliability: Reliability and durability are designed into every C5. High-quality components provide a long life of worry free use. Power Options: Choose between standard high wattage or low wattage models based on the specific needs of the application. Energy Star: C5 3 Series Full Height, 3 /4 Height, and solid door 1 /2 Height cabinets are Energy Star. Blue Full Height Full Clear Door Red Full Height Dutch Clear Doors Gray Full Height Dutch Solid Doors TM C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets InterMetro Industries Corporation North Washington Street Wilkes-Barre, PA 18705 www.metro.com Gray 3 /4 Height Full Clear Door Blue 1 /2 Height Full Solid Door 13.93
C5 3 Series Insulation armour Heated Holding and Proofing Cabinets Module Options Temperature Easy-to-use dial puts you in control of cabinet temperature. Easy-to-read Digital Thermometer can be seen from a distance. Holding Module: Heat generation only for higher temperature heated holding applications. Temperature Easy-to-use dial puts you in control of cabinet temperature. Easy-to-read Digital Thermometer can be seen from a distance. Moisture Control the amount of moisture in the cabinet when holding. Moisture Module: Simultaneous heat and moisture generation for higher temperature heated holding applications and lower temperature proofing applications. Humidity is generated at both high and low temperatures. Temperature Easy-to-use dial puts you in control of cabinet temperature. Moisture In Proofing mode control the amount of moisture in the cabinet. Proofing Module: Heat and moisture generation for lower temperature proofing applications. Easy-to-read Digital Thermometer can be seen from a distance. Temperature Easy-to-use dial puts you in control of cabinet temperature. Moisture In Proofing mode control the amount of moisture in the cabinet. Flexible Choose Holding or Proofing mode at the flip of a switch. Combination Module: Heat generation only for higher temperature holding applications or heat and moisture generation for lower temperature proofing applications. Humidity is generated only at lower temperatures when in Proof Mode. Humidity is not generated when in Hold Mode. Easy-to-read Digital Thermometer can be seen from a distance.
C5 3 Series Insulation armour Heated Holding and Proofing Cabinets Slide Options Universal: Adjustable wire slides, with SiteSelect, hold 18" x 26" (457 x 660mm) sheet, 12" x 20" (305 x 508mm) steam table, 2/1 or 1/1 GN pans, and adjust on 1 1 /2" (38mm) increments. Lip Load: Fixed aluminum extrusions hold 18" x 26" (457 x 660mm) sheet pans on 1 1 /2" (38mm) increments. Fixed Wire: Fixed slides hold 18" x 26" (457 x 660mm) sheet, 12" x 20" (305 x 508mm) steam table, 2/1 GN, or 1/1 GN pans on 3" (76mm) increments. Universal Slides Pan Capacity** Lip Load Slide Pan Fixed Wire Slides Pan Capacity Slide Pairs 18" x 26" 12" x 20" x 2 1 /2" Capacity 18" x 26" 12" x 20" x 2 1 /2" Cabinet Size Provided Max.* GN 2/1 GN 1/1 18" x 26" GN 2/1 GN 1/1 Full Height 18 37 18 34 35 18 34 Full Height/Dutch 18 35 17 32 34 17 32 3 /4 Height 14 29 13 26 27 14 26 1 /2 Height 8 17 8 16 17 8 16 *Maximum number of slide pairs @ 1 /2" spacing. Additional slide pairs ordered separately. **Capacity based on standard number of slide pairs provided. Options/Accessories* Small Item Shelf (C5-SHELF) Stainless Steel Legs (C5-SSLEGS) Universal Slide Pair (C5-USLIDECPR) 6" Casters (C5-6CASTER) Rear Rigid Casters (C5-5RDGCSTR) Travel Latch (C5-TRVL) Flush Door Latch (C5-LATCHFLUSH-1)** Right Angle Plug (C5-RTANGPLG) Left Hand Hinging (DD3768) Stainless Steel Universal Slides (call) *Specify as a line item with an A added to the end of the cabinet part number. **Two required for Dutch Door models. Power Options Lower Wattage Combination and Holding Modules Export 220-240 Voltage Modules with Centigrade Thermometer Display Limited Edition Orange Full Height Dutch Solid Doors
13.93 C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets TM C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets TM Specifications Cabinet Material:.063" (1.8mm) aluminum, natural interior with.125" (3.2mm) aluminum chassis. Insulation Armour : High Density Polyethylene (HDPE). Casters: Four casters with 5" (127mm) donut neoprene wheel, double ball bearing swivel, ball bearing axel, nickel plated, two with brake. Solid Doors: Fully insulated with 1" (25.4mm) fiberglass, double panel.063" (1.8mm) aluminum, brushed exterior, natural interior. Clear Doors: Extruded aluminum powder coated frame with.090" (2.3mm) polycarbonate window. Hinges: Field reversible, double hinged, 180 swing, with long-life nylon bearings. Gaskets: High temperature, door mounted, Santoprene gaskets. Latches: Polymer high-strength magnetic pull latch with lever-action release. Hand Holds: Molded into the Insulation Armour on all four corners. Universal Slides: 1 /4" (6.4mm) dia. nickel-chrome electroplated wire, adjustable on 1 1 /2" (38mm) increments. Lip Load Slides: 1 1 /2"x 1 /2"x.063 (38x38x1.8mm) extruded aluminum channel slides, 1 1 /2" (38mm) fixed spacing. Fixed Wire Slides: 1 /4" (6.4mm) dia. nickel-chrome electroplated wire, welded on 3" (76mm) spacing. Drip Trough: Smooth polymer drip trough with catch pan. Holding Modules: Removable without tools, digital thermometer, recessed control dials, master on/off switch, Power On light, water pan, ball bearing blower forced air system, 7 1 /2' cord, UL, CUL, and NSF Listed. Electrical and Performance: Holding Module: 2000 Watt, 120 Volts, 60 Hz., single phase, 16.7 Amps. 80 F to 200 F operating temperature range. NEMA 5-20P plug. Moisture Module: 2000 Watt, 120 Volts, 60 Hz., single phase, 16.7 Amps. 80 F to 200 F operating temperature range. 35% RH at 160 F, 95% RH at 95 F. NEMA 5-20P plug. Proofing Module: 1440 Watt, 120 Volts, 60 Hz., single phase, 12 Amps. 80 F to 120 F operating temperature range. 95% RH at 95 F. NEMA 5-15P plug. Combination Module: 2000 Watt, 120 Volts, 60 Hz., single phase, 16.7 Amps. 80 F to 200 F operating temperature range. 95% RH at 95 F. NEMA 5-20P plug. 71" (1803mm) 59" (1499mm) All cabinets are 27 5 /8" (702mm) wide and 31 1 /2" (800mm) deep. 44" (1118mm) Full Height 3 /4 Height 1 /2 Height Clearance Requirements: 18" (46cm) away from any cooking equipment. AVOID contact with surfaces that exceed 200 F (90 C). Minimum clearance from enclosures is 1 1 /2" (38mm) on sides, back and top. All Metro Catalog Sheets are available on our Web Site: www.metro.com C5 3 9 - - CDC U W G NEMA 5-20P For Standard Wattage Cabinets (120V, 16A, 60Hz, 2000W) Low Watt Model Number Description C5 3 9 - C LDC -U NEMA 5-15P Cabinet Height 9 = Full Height 7 = 3/4 Height 5 = 1/2 Height NEMA 6-15P Add L for Lower Wattage Combination or Holding Module Cabinets (120V, 12A, 60Hz, 1440W) Export Model Number Description Module Type C = Combination M = Moisture H = Heated Holding P = Proofing C5 3 9 - C XDC -U Blue or Gray Model Description Add X for Export Cabinets (220-240V, 7.6-8.3A, 50/60Hz, 1681-2000W) Models with Accessories or Options C5 3 9 -CDC- UA C5 3 9 -CDC- U- BUA Door Style FS = Full Length Solid FC = Full Length Clear *Please note: Dutch doors only available on full-height models. Cabinets ordered without a color designation default to Red. Slide Type U = Universal Wire 4 = Fixed Wire L = Lip Load Aluminum C5 3 9 - C DC - U -BU **Cabinets ordered without a color designation default to Red. DS = Dutch Solid * DC = Dutch Clear * Color ** No Suffix = Red BU = Blue GY = Gray An A suffix indicates that accessories need to be factory assembled to the cabinet. Order accessories separately. Colors: Red, Blue, and Gray are standard. Other colors such as Sage Green, Beige, Yellow, and Orange are available for a limited time. Call for availability and color match requirements. Metro Heated cabinets are for hot food holding applications only. InterMetro Industries Corporation North Washington Street, Wilkes-Barre, PA 18705 Phone: 570-825-2741 Fax: 570-825-2852 L03-270 Printed in U.S.A. Rev. 1/09 Information and specifications are subject to change without notice. Please confirm at time of order. Copyright 2009 InterMetro Industries Corp. For Product Information: U.S. and Canada: 1.800.433.2232 Latin America: 1.561.333.3824 Europe: +31.76.587.7550 Asia/Pacific: +65.6567.8003 Middle East/Africa: +971.4.811.8286
Item # TM Job Metro C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets Insulation Armour : Patent pending insulation technology retains heat, saves energy, and provides a cool-to-touch exterior. Durable polymer construction is dent, impact, and stain resistant. Molded-in hand holds create vertical handles for mobile applications. Control: Three holding modules are available. All feature an easyto-read digital thermometer, recessed control dials, a master on/off switch, and power indicator lights. Combination Module: At the flip of a switch change from heated holding mode to proofing mode. Individual analog controls for temperature and humidity levels. Holding Module: For heated holding applications. Analog temperature control and a passive humidity generation system. Proofing Module: For proofing applications only. Individual analog controls for temperature and humidity levels. Performance: All modules provide fast heat-up and recovery through a thermostatically controlled, forced air heating system. Sizes: C5 3 Series cabinets are available in Full Height (71", 1803mm), 3 /4 Height (59", 1499mm), and 1 /2 Height (44", 1118mm) sizes. Doors: Solid insulated aluminum or clear polycarbonate doors are available. Full Height cabinets can be configured with full length or Dutch style doors. Clear doors provide visibility of the contents of the cabinet without the heat loss associated with opening the door. Capacity: Three slide styles provide maximum holding capacity. Universal: Adjustable wire slides, with SiteSelect, hold 18"x26" sheet, 12"x20" steam table, 2/1 or 1/1 GN pans, and adjust on 1 1 /2" (38mm) increments. Lip Load: Fixed aluminum extrusions hold 18"x26" sheet pans on 1 1 /2" (38mm) increments. Fixed Wire: Fixed slides hold 18"x26" sheet, 12"x20" steam table, 2/1 GN, or 1/1 GN pans on 3" (76mm) increments. Removable Module: All modules are removable, without tools, for easy cleaning of the cabinet interior. Future module upgrades or changes can occur without cabinet body replacement. Reliability: Reliability and durability are designed into every C5. High-quality components provide a long life of worry free use. Energy Star: All C5 3 Series cabinets are Energy Star. Options/Accessories* Small Item Shelf (C5-SHELF) Stainless Steel Legs (C5-SSLEGS) Universal Slide Pair (C5-USLIDECPR) 6" Casters (C5-6CASTER) Rear Rigid Casters (C5-5RDGCSTR) Travel Latch (C5-TRVL) Right Angle Plug (C5-RTANGPLG) Left Hand Hinging (DD3768) Stainless Steel Universal Slides *Specify as a line item with an A added to the end of the cabinet part number. Power Options Lower Wattage Combination and Holding Modules Export 240/220 Modules with Centigrade Thermometer Display *Patents Pending InterMetro Industries Corporation North Washington Street Wilkes-Barre, PA 18705 www.metro.com Full Height Full Clear Door 3 /4 Height Full Solid Door Full Height Dutch Solid Doors Full Height Dutch Clear Doors 1 /2 Height Full Clear Door TM C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets 13.93
13.93 C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets TM Specifications Cabinet Material:.063" (1.8mm) aluminum, natural interior with.125" (3.2mm) aluminum chassis. Insulation Armour : High Density Polyethylene (HDPE). Casters: Four casters with 5" (127mm) donut neoprene wheel, double ball bearing swivel, ball bearing axel, nickel plated, two with brake Solid Doors: Fully insulated with 1" (25.4mm) fiberglass, double panel.063" (1.8mm) aluminum, brushed exterior, natural interior. Clear Doors: Extruded aluminum powder coated frame with.090" (2.3mm) polycarbonate window. Hinges: Field reversible, double hinged, 180 swing, with long-life nylon bearings. Gaskets: High temperature, door mounted, Santoprene gaskets. Latches: Polymer high-strength magnetic pull latch with lever-action release. Hand Holds: Molded into the Insulation Armour on all four corners. Universal Slides: 1 /4" (6.4mm) dia. nickel-chrome electroplated wire, adjustable on 1 1 /2" (38mm) increments. Lip Load Slides: 1 1 /2"x 1 /2"x.063 (38x38x1.8mm) extruded aluminum channel slides, 1 1 /2" (38mm) fixed spacing. Fixed Wire Slides: 1 /4" (6.4mm) dia. nickel-chrome electroplated wire, welded on 3" (76mm) spacing. Slide Capacities: Universal Slides Lip Load Slide Fixed Wire Slides Slide Pairs Pan Capacity** Pan Capacity Pan Capacity Cabinet Size Provided Max.* 18"x26" 12"x20"x2 1 /2" 18"x26" 18"x26" 12"x20"x2 1 /2" Full Height 18 37 18 34 35 18 34 Full Height/ Dutch 18 35 17 32 34 17 32 3 /4 Height 14 29 13 26 27 14 26 1 /2 Height 8 17 8 16 17 8 16 *Maximum number of slide pairs @ 1 1 /2" spacing. Additional slide pairs ordered separately. **Capacity based on standard number of slide pairs provided. Drip Trough: Smooth polymer drip trough with catch pan. Holding Modules: Removable without tools, digital thermometer, recessed control dials, master on/off switch, Power On light, water pan, ball bearing blower forced air system, 7 1 /2' cord, UL, CUL, and NSF Listed. Electrical and Performance: Combination Module: 2000 Watt, 120 Volts, 60 Hz., single phase, 16.7 Amps. 80 F to 200 F operating temperature range. 95% RH at 95 F. NEMA 5-20P plug. Holding Module: 2000 Watt, 120 Volts, 60 Hz., single phase, 16.7 Amps. 80 F to 200 F operating temperature range. NEMA 5-20P plug. Proofing Module: 1440 Watt, 120 Volts, 60 Hz., single phase, 12 Amps. 80 F to 120 F operating temperature range. 95% RH at 95 F. NEMA 5-15P plug. Dimensions 71" (1803mm) TM C5 3 Series Insulation Armour Heated Holding and Proofing Cabinets 59" (1499mm) All cabinets are 27 5 /8" (702mm) wide and 31 1 /2" (800mm) deep. 44" (1118mm) Full Height 3 /4 Height 1 /2 Height All Metro Catalog Sheets are available on our Web Site: www.metro.com NEMA 5-20P NEMA 5-20P NEMA 5-15P Part Numbers Full Height Cabinets Part # Module Doors Slides C539-CFC-4 Combo Full-Length Clear Fixed Wire C539-CFC-U Combo Full-Length Clear Universal Wire C539-CFC-L Combo Full-Length Clear Lip Load C539-HFC-4 Holding Full-Length Clear Fixed Wire C539-HFC-U Holding Full-Length Clear Universal Wire C539-HFC-L Holding Full-Length Clear Lip Load C539-PFC-4 Proofing Full-Length Clear Fixed Wire C539-PFC-U Proofing Full-Length Clear Universal Wire C539-PFC-L Proofing Full-Length Clear Lip Load C539-CFS-4 Combo Full-Length Solid Fixed Wire C539-CFS-U Combo Full-Length Solid Universal Wire C539-CFS-L Combo Full-Length Solid Lip Load C539-HFS-4 Holding Full-Length Solid Fixed Wire C539-HFS-U Holding Full-Length Solid Universal Wire C539-HFS-L Holding Full-Length Solid Lip Load C539-PFS-4 Proofing Full-Length Solid Fixed Wire C539-PFS-U Proofing Full-Length Solid Universal Wire C539-PFS-L Proofing Full-Length Solid Lip Load C539-CDC-4 Combo Dutch Clear Fixed Wire C539-CDC-U Combo Dutch Clear Universal Wire C539-CDC-L Combo Dutch Clear Lip Load C539-HDC-4 Holding Dutch Clear Fixed Wire C539-HDC-U Holding Dutch Clear Universal Wire C539-HDC-L Holding Dutch Clear Lip Load C539-PDC-4 Proofing Dutch Clear Fixed Wire C539-PDC-U Proofing Dutch Clear Universal Wire C539-PDC-L Proofing Dutch Clear Lip Load C539-CDS-4 Combo Dutch Solid Fixed Wire C539-CDS-U Combo Dutch Solid Universal Wire C539-CDS-L Combo Dutch Solid Lip Load C539-HDS-4 Holding Dutch Solid Fixed Wire C539-HDS-U Holding Dutch Solid Universal Wire C539-HDS-L Holding Dutch Solid Lip Load C539-PDS-4 Proofing Dutch Solid Fixed Wire C539-PDS-U Proofing Dutch Solid Universal Wire C539-PDS-L Proofing Dutch Solid Lip Load 3 /4 Height Cabinets C537-CFC-4 Combo Full-Length Clear Fixed Wire C537-CFC-U Combo Full-Length Clear Universal Wire C537-CFC-L Combo Full-Length Clear Lip Load C537-HFC-4 Holding Full-Length Clear Fixed Wire C537-HFC-U Holding Full-Length Clear Universal Wire C537-HFC-L Holding Full-Length Clear Lip Load C537-PFC-4 Proofing Full-Length Clear Fixed Wire C537-PFC-U Proofing Full-Length Clear Universal Wire C537-PFC-L Proofing Full-Length Clear Lip Load C537-CFS-4 Combo Full-Length Solid Fixed Wire C537-CFS-U Combo Full-Length Solid Universal Wire C537-CFS-L Combo Full-Length Solid Lip Load C537-HFS-4 Holding Full-Length Solid Fixed Wire C537-HFS-U Holding Full-Length Solid Universal Wire C537-HFS-L Holding Full-Length Solid Lip Load C537-PFS-4 Proofing Full-Length Solid Fixed Wire C537-PFS-U Proofing Full-Length Solid Universal Wire C537-PFS-L Proofing Full-Length Solid Lip Load 1 /2 Height Cabinets C535-CFC-4 Combo Full-Length Clear Fixed Wire C535-CFC-U Combo Full-Length Clear Universal Wire C535-CFC-L Combo Full-Length Clear Lip Load C535-HFC-4 Holding Full-Length Clear Fixed Wire C535-HFC-U Holding Full-Length Clear Universal Wire C535-HFC-L Holding Full-Length Clear Lip Load C535-PFC-4 Proofing Full-Length Clear Fixed Wire C535-PFC-U Proofing Full-Length Clear Universal Wire C535-PFC-L Proofing Full-Length Clear Lip Load C535-CFS-4 Combo Full-Length Solid Fixed Wire C535-CFS-U Combo Full-Length Solid Universal Wire C535-CFS-L Combo Full-Length Solid Lip Load C535-HFS-4 Holding Full-Length Solid Fixed Wire C535-HFS-U Holding Full-Length Solid Universal Wire C535-HFS-L Holding Full-Length Solid Lip Load C535-PFS-4 Proofing Full-Length Solid Fixed Wire C535-PFS-U Proofing Full-Length Solid Universal Wire C535-PFS-L Proofing Full-Length Solid Lip Load Add L for Low Watt (1440W, Add X for 240/220v, 12 Amp) C or H Modules. 50/60 Hz., single Ex: C539-CLDS-U phase for Export. NEMA NEMA 5-15P Ex: C539-CXDS-U 6-15P Metro Heated cabinets are for hot food holding applications only. InterMetro Industries Corporation North Washington Street, Wilkes-Barre, PA 18705 Phone: 570-825-2741 Fax: 570-825-2852 For Product Information Call: 1-800-433-2232 L03-270 Printed in U.S.A. 10/07 Information and specifications are subject to change without notice. Please confirm at time of order. Copyright 2007 InterMetro Industries Corp.
ITEM# GLO-RAY DESIGNER MERCHANDISING WARMERS Models GR2SDH-24, -30, -36, -42, -48, -54, -60 GR2SDH-24D, -30D, -36D, -42D, -48D, -54D, -60D GR2SDS-24, -30, -36, -42, -48, -54, -60 GR2SDS-24D, -30D, -36D, -42D, -48D, -54D, -60D Designed to hold hot wrapped food at optimum serving temperatures without affecting quality, the Hatco Glo-Ray Designer Merchandising Warmers are the perfect displays to showcase hot fast foods and boost impulse sales. Combining state-of-the-art design with performance, these warmers place the focus on the product while holding hot food safely at proper serving temperatures. The modern design is perfect for front of the house use. Designer powdercoated inset panels blend these units with the décor while providing a durable, easy-to-clean surface. Glo-Ray Designer Merchandising Warmers have prefocused infrared top heat and a thermostatically-controlled, hardcoated heated base to extend the holding times of most food. All models are made of aluminum with tempered glass end panels. Shatter-resistant incandescent lights illuminate the food holding area. FLEXIBILITY This warmer offers the convenience of self-serve and the efficiency of kitchento-server holding. Available with slant or horizontal shelves, the Glo-Ray Designer Merchandising Warmers are offered in both single and dual shelf models. The Designer series warmers come standard with black inset panels. Choose from five other color options to blend the warmer with any décor. QUALITY The following features assure the finest performance for years to come: All models have prefocused infrared top heat directing heat to the outer edges of the holding surface where heat loss is the greatest. These warmers feature a thermostatically-controlled, hardcoated heated base, Designer color inset panels, 4" (102 mm) Designer legs, and a cord and plug set. Available in heated surface widths from 23 3 4" to 59 3 4" (603 to 1518 mm) with overall widths of 30 1 8" to 66 1 8" (765 to 1680 mm). Shatter-resistant incandescent lights enhance product display while safeguarding food products from bulb breakage. An optional Indicating Temperature Control enhances accurate control of temperature. Model GR2SDH-30 with Designer color inset panels Divider Rods Model GR2SDS-30D with Designer color inset panels Model Width Divider Rods Provided Average Chute Width 30 1 8" ( 765 mm) 5 Rods per Shelf 3 3 4" ( 95 mm) 36 1 8" ( 918 mm) 6 Rods per Shelf 4 1 4" (108 mm) 42 1 8" (1070 mm) 7 Rods per Shelf 4 1 2" (114 mm) 48 1 8" (1222 mm) 8 Rods per Shelf 4 1 2" (114 mm) 54 1 8" (1375 mm) 9 Rods per Shelf 4 1 2" (114 mm) 60 1 8" (1527 mm) 10 Rods per Shelf 4 5 8" (117 mm) 66 1 8" (1680 mm) 12 Rods per Shelf 4 1 2" (114 mm) METAL SHEATHED HEATING ELEMENTS GUARANTEED AGAINST BURNOUT AND BREAKAGE FOR TWO YEARS, BLANKET ELEMENTS FOR ONE YEAR. ANSI/NSF 4 HATCO CORPORATION P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Fax (800) 543-7521 Int l. Fax (414) 671-3976 www.hatcocorp.com E-mail: equipsales@hatcocorp.com Form No. GR2SD Spec Sheet Printed in U.S.A. April 2007
ITEM# GLO-RAY DESIGNER MERCHANDISING WARMERS Models GR2SDH-24, -30, -36, -42, -48, -54, -60 GR2SDH-24D, -30D, -36D, -42D, -48D, -54D, -60D GR2SDS-24, -30, -36, -42, -48, -54, -60 GR2SDS-24D, -30D, -36D, -42D, -48D, -54D, -60D 30 1 8" to 66 1 8" (765 to 1680 mm) 27" (686 mm) 30 1 8" to 66 1 8" (765 to 1680 mm) 26 5 8" (676 mm) 23 3 4" to 59 3 4" (603 to 1518 mm) 8" (203 mm) 18" 22" (559 mm) (457 mm) GR2SDH Models 23 3 4" to 59 3 4" (603 to 1518 mm) 22 3 8" (568 mm) 8" (203 mm) 22" (559 mm) GR2SDS Models FRONT VIEW SIDE VIEW FRONT VIEW SIDE VIEW 30 1 8" to 66 1 8" (765 to 1680 mm) 27" (686 mm) 30 1 8" to 66 1 8" (765 to 1680 mm) 26 5 8" (676 mm) 23 3 4" to 59 3 4" (603 to 1518 mm) 29" (737 mm) 22" (559 mm) GR2SDH-D Models 23 3 4" to 59 3 4" (603 to 1518 mm) 33 3 8" (848 mm) 22" (559 mm) GR2SDS-D Models 23 3 4" to 59 3 4" (603 to 1518 mm) 8" (203 mm) 22" (559 mm) 23 3 4" to 59 3 4" (603 to 1518 mm) 8" (203 mm) 22" (559 mm) SPECIFICATIONS Horizontal Models Model Watts Width Shipping Weight GR2SDH-24 820 30 1 8" ( 765 mm) 87 lbs. ( 40 kg) GR2SDH-30 1020 36 1 8" ( 918 mm) 120 lbs. ( 55 kg) GR2SDH-36 1220 42 1 8" (1070 mm) 129 lbs. ( 59 kg) GR2SDH-42 1490 48 1 8" (1222 mm) 138 lbs. ( 63 kg) GR2SDH-48 1690 54 1 8" (1375 mm) 160 lbs. ( 73 kg) GR2SDH-54 1890 60 1 8" (1527 mm) 172 lbs. ( 78 kg) GR2SDH-60 2210 66 1 8" (1680 mm) 187 lbs. ( 85 kg) GR2SDH-24D 1640 30 1 8" ( 765 mm) 150 lbs. ( 68 kg) GR2SDH-30D 2040 36 1 8" ( 918 mm) 178 lbs. ( 81 kg) GR2SDH-36D 2440 42 1 8" (1070 mm) 198 lbs. ( 90 kg) GR2SDH-42D 2980 48 1 8" (1222 mm) 218 lbs. ( 99 kg) GR2SDH-48D 3380 54 1 8" (1375 mm) 238 lbs. (108 kg) GR2SDH-54D 3780 60 1 8" (1527 mm) 258 lbs. (117 kg) GR2SDH-60D 4420 66 1 8" (1680 mm) 280 lbs. (127 kg) Slant Models Model Watts Width Shipping Weight GR2SDS-24 820 30 1 8" ( 765 mm) 104 lbs. ( 47 kg) GR2SDS-30 1020 36 1 8" ( 918 mm) 116 lbs. ( 53 kg) GR2SDS-36 1220 42 1 8" (1070 mm) 136 lbs. ( 62 kg) GR2SDS-42 1490 48 1 8" (1222 mm) 155 lbs. ( 70 kg) GR2SDS-48 1690 54 1 8" (1375 mm) 164 lbs. ( 74 kg) GR2SDS-54 1890 60 1 8" (1527 mm) 182 lbs. ( 83 kg) GR2SDS-60 2210 66 1 8" (1680 mm) 202 lbs. ( 92 kg) GR2SDS-24D 1640 30 1 8" ( 765 mm) 162 lbs. ( 74 kg) GR2SDS-30D 2040 36 1 8" ( 918 mm) 174 lbs. ( 79 kg) GR2SDS-36D 2440 42 1 8" (1070 mm) 190 lbs. ( 86 kg) GR2SDS-42D 2980 48 1 8" (1222 mm) 218 lbs. ( 99 kg) GR2SDS-48D 3380 54 1 8" (1375 mm) 240 lbs. (109 kg) GR2SDS-54D 3780 60 1 8" (1527 mm) 260 lbs. (118 kg) GR2SDS-60D 4420 66 1 8" (1680 mm) 296 lbs. (135 kg) Dual Shelf Single Shelf Dual Shelf Single Shelf FRONT VIEW SIDE VIEW When no color is specified, color inset panels will be black, corner caps will be dark gray. NSF requires units over 36" (914 mm) in width or weighing more than 80 lbs. (36 kg) to be either sealed, or raised on the installation surface with the 4" (102 mm) legs included. OPTIONS (NOT FOR RETROFIT) Unit and Inset Panel Designer Colors: Warm Red, Black, Gray Granite, White Granite, Navy Blue, and Hunter Green 5" (127 mm) Breath Protector on Customer Side Indicating Temperature Control (ITC) Halogen Bulbs in lieu of Standard Display Lights PRODUCT SPECS Designer Merchandising Warmer The Designer Merchandising Warmer shall be a Glo-Ray Model...as manufactured by the Hatco Corporation, Milwaukee, WI 53234 U.S.A. With 24/7 service (U.S. and Canada only), the warmer shall be rated at...watts,...volts, and be...inches (millimeters) in overall width. It shall consist of a thermostatically-controlled heated base, infrared heat from FRONT VIEW DIMENSIONS Horizontal Models (GR2SDH) Single: 30 1 8"- 66 1 8"W x 27"D x 18"H (765-1680 x 686 x 457 mm). Dual: 30 1 8"- 66 1 8"W x 27"D x 29"H (765-1680 x 686 x 737 mm). Slant Models (GR2SDS) Single: 30 1 8"- 66 1 8"W x 26 5 8"D x 22 3 8"H (765-1680 x 676 x 568 mm). Dual: 30 1 8"- 66 1 8"W x 26 5 8"D x 33 3 8"H (765-1680 x 676 x 848 mm). Heated Surface: 23 3 4"- 59 3 4"W x 22"D (603-1518 x 559 mm). VOLTAGE GR2SDH-24 to -48 & GR2SDS-24 to -48: 120 volts, single phase (uses NEMA 5-15P, models GR2SDH-42 to -48 & GR2SDS-42 to -48 uses NEMA 5-20P for Canada). GR2SDH-54 & GR2SDS-54: 120 volts, single phase (uses NEMA 5-20P). GR2SDH-60 & GR2SDS-60: 120 volts, single phase (uses NEMA 5-30P). GR2SDH-24D & GR2SDS-24D: 120 volts, single phase (uses NEMA 5-15P, uses NEMA 5-20P for Canada). GR2SDH-30D to -54D & GR2SDS-30D to -54D: 120/208 volts, or 120/240 volts, single phase, 4-wire (uses NEMA L14-20P). GR2SDH-60D & GR2SDS-60D: 120/208 volts or 120/240 volts, single phase, 4-wire (uses NEMA L14-30P). Export voltages available. CORD LOCATION Back center of base on control side. PLUG CONFIGURATIONS NEMA 5-15P NEMA L14-30P ACCESSORIES Additional Stainless Steel Divider Rods Flip-up Doors Control Covers Display Sign Holder (Signs not included) SIDE VIEW NEMA 5-20P NEMA 5-30P CEE 7/7 Schuko BS-1363 NEMA L14-20P above, full-view tempered glass sides, Designer color inset panels, and incandescent display lights. The infrared heating element shall be tubular metal sheathed and the warmer shall have a cord with plug attached. Accessories shall include additional stainless steel dividers rods, flip-up doors, display sign holder, and control covers. HATCO CORPORATION P.O. Box 340500 Milwaukee, WI 53234-0500 U.S.A. (800) 558-0607 (414) 671-6350 Fax (800) 543-7521 Int l. Fax (414) 671-3976 www.hatcocorp.com E-mail: equipsales@hatcocorp.com Printed in U.S.A. Form No. GR2SD Spec Sheet April 2007
Item No. Equipment Stand Standard Tray Rail Height Models ES28, ES28R, ES28L, ES28RL Low Tray Rail Height Models ES28RS, ES28LS, ES28RLS Specifier Identification No. Model No. Quantity Features & Benefits Perfect for cash registers or computers at the end of a school lunch line or for completing any self-serve buffet or salad bar concept. Increases food preparation area for microwave ovens, slicers and other appliances. Available with or without side rails, or with side rails to the left, right or on both sides of center drawer. Handy center drawer slides open to conveniently store cash, customer receipts or equipment accessories. Open bottom shelf features a cut out design so that the operator can sit or stand comfortably without bumping ankles or knees. Tough one-piece, seamless, double-wall, high-density, polyethylene construction. Polyurethane foam insulation provides greater strength and durability. Easy to clean and will not dent, crack, rust, chip or break. Tray rails are available in two convenient heights, 34 1 /2 (88 cm) and 27 1 /2 (70 cm), to accommodate service for both adults and children. Separate 2 1 /2 (6,4 cm) opening through both top and bottom shelves allows cords and plugs to drop safely and neatly to the floor. Four each 5 (12,7 cm) casters, 2 fixed, 2 swivel w/ brakes, offer smooth maneuvering across a lunchroom floor or across campus. Non-electrical. No assembly required. Available in 6 colors. ES28R (Standard Tray Rail Height) ES28R (Standard Tray Rail Height) ES28RLS (Low Tray Rail Height) ES28RL (Standard Tray Rail Height) Approvals 2008 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056-U.S.A. T e l e p h o n e (1)714 848 1555 Toll Free 800 854 7631 Customer Service 800 833 3003 LIT FCST-0102-56 55
Equipment Stand Standard Tray Rail Height Models ES28, ES28R, ES28L, ES28RL Low Tray Rail Height Models ES28RS, ES28LS, ES28RLS Item No. Specifier Identification No. Model No. Quantity ES28L ES28R ES28RL ES28 ES28LS ES28RS ES28RLS Depth Dimension Specifications Dimensions W x D x H Case lbs./cube Code Description (w/tray Rails and Casters) Kg/m 3 Standard Model ES28 Stand only 28" x 28" x 39 1 /2" 76 (19.15) (71 x 71 x 100 cm) 35 (0,54) ES28R Stand w/rail on 36" x 28" x 39 1 /2" 83 (19.15) right side (91 x 71 x 100 cm) 38 (0,54) ES28L Stand w/rail on 36" x 28" x 39 1 /2" 83 (19.15) left side (91 x 71 x 100 cm) 38 (0,54) ES28RL Stand w/rails on 44" x 28" x 39 1 /2" 89 (19.15) right and left sides (112 x 71 x 100 cm) 41 (0,54) Architect Specs The portable merchandising equipment cart shall be an Equipment Stand, Model..., manufactured by Cambro Mfg. Co., Huntington Beach, CA 92648 U.S.A. It shall be made of one-piece, seamless, double-wall polyethylene and foaminjected polyurethane. It shall be available with or without side tray rails and the tray rails shall be available in both 34 1 /2 (88 cm) standard height and 27 1 /2 (70 cm) low height. It shall have a central drawer. It shall have an open compartment shelf, designed with a cut out section for operator comfort, and also offering convenient storage. It shall have 4 each 5 (12,7 cm) casters, 2 fixed, 2 swivel w/ brakes. It shall have a separate 2 1 /2 (6,4 cm) opening through both top and bottom shelves for cords and plugs to drop through. It shall be available fully assembled and in 6 colors. Dimension Tolerance: +/- 1 /4" (0,64 cm) Dimensions W x D x H Case lbs./cube Code Description (w/tray Rails and Casters) Kg/m 3 Low Model ES28RS Stand w/rail on 36" x 28" x 39 1 /2" 83 (19.15) right side (91 x 71 x 100 cm) 38 (0,54) ES28LS Stand w/rail on 36" x 28" x 39 1 /2" 83 (19.15) left side (91 x 71 x 100 cm) 38 (0,54) ES28RLS Stand w/rails on 44" x 28" x 39 1 /2" 89 (19.15) right and left sides (112 x 71 x 100 cm) 41 (0,54) Standard Colors Black (110) Granite Green (192) Slate Blue (401) Granite Gray (191) Hot Red (158) Navy Blue (186) Approvals 2008 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056-U.S.A. T e l e p h o n e (1)714 848 1555 Toll Free 800 854 7631 Customer Service 800 833 3003 Printed in USA
Item # Quantity C.S.I. Section 11400 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C44A DISHWASHER STANDARD FEATURES 202 racks per hour C44A Opti-RinSe system Ball detent clutch conveyor drive mechanism Top mounted controls Stainless steel anti-clogging wash arms Stainless front panel, frame and legs Automatic fill Auto-timer Scrap screen and deep basket system Stainless steel self-draining pump and impeller Fixed pump intake screen Door actuated drain closure Door interlock switch on all doors Vent fan control Convertible hot water or low temp final rinse Booster heater control MODEL C44A Dishwasher ACCESSORIES Stainless steel vent hoods Direct drive unloader Side loader Specifications, Details and Dimensions on Inside and Back. R DIRECTION OF OPERATION Right to Left Left to Right VOLTAGE 208/60/1 208/60/3 240/60/1 240/60/3 480/60/3 OPTIONS AT EXTRA COST Stainless steel pressureless 15 kw or 30 kw booster heater Single point electrical connection (does not include booster heater) 6" higher than standard chamber Conveyor dwell Side loader Blower-dryer C44A DISHWASHER F-39950 C44A Dishwasher Page 1 of 12
C44A DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C-LINE DISHWASHER NOW STANDARD WITH MORE PRODUCTIVE FEATURES THAN EVER... Inside and out the C-Line Hobart dishwashers are packed with standard components and design innovations that make them the biggest value in the dishwasher industry. Stainless Steel Self-Draining Pump and Impeller. Pump and impeller are stainless steel for maximum durability. A fixed pump intake screen prevents debris from entering into the pump. Wash Arms. Computer-designed wash arms resist clogging, easily removed for cleaning (C-44A shown). Opti-RinSe. Hobart s exclusive patent pending Opti-RinSe significantly reduces operating cost by reducing rinse water and the energy required to heat the water. The unique spray pattern uses large droplets to more efficiently sanitize the ware. Lift-Out Scrap Basket. Screen design sheds soil more easily than flat screens, reduces frequency of cleaning easy to empty large soil particles... Just lift out scrap basket under screens. OPTIONAL BOOSTER HEATER Built-in Pressureless Stainless Steel Booster Heater. Interwired and interplumbed. Saves on installation and saves floor space. Simplifies operation with just one switch to power dishmachine and booster. OTHER STANDARD FEATURES... Low-Temp Convertibility In Field. Order your C-Line with hot water sanitizing or energy-saving low temperature chemical sanitizing then, if requirements change, convert from one mode to the other in the field. An exclusive feature standard from Hobart. Auto-Fill. One button automatic fill ensures optimum tank level, and the simplest operation. Auto-Timer. Automatically activates the warewasher when a rack enters the machine, and after the last rack has passed, shuts off the pump and conveyor while maintaining tank heat temperature. Extends machine life, requires less operator attention and promotes significant energy savings. Door Actuated Drain Closure. Closing the door automatically actuates drain closure, eliminates extra manual steps, insures that closure is in the correct position. Vent Fan Control and Booster Heater Control. Allows for interconnection to dishwasher. Page 2 of 12 F-39950 C44A Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C44A DISHWASHER AVAILABLE OPTIONS AND ACCESSORIES... Flexibility is synonymous with Hobart C-Line dishwashers. If your operation demands a dishwasher with a vent hood, an extended hood... a recirculating prewash, just specify the combination of options that suit your needs. OTHER AVAILABLE OPTIONS... Condenser, blower-dryer, conveyor dwell, steam booster heater, and a single-point electrical connection for electric heat machines. C44A Machine Ratings (Mechanical) Racks per hour (19 3 4" x 19 3 4") 202 Conveyor Speed - feet per minute 5.6 max. Dishes per Hour (Average 25 per rack) 5,025 Glasses per Hour (Average 45 per rack) 9,045 Floor Space - Table to Table (Inches) 44 Overall Dimensions - H x W x D (Inches) 70 1 4 x 45 1 4 x 30 1 4 Motor H.P. 2 Side Loader. Save up to 20 square feet in the dishroom layout with an optional C-Line Side Loader. Racks are indexed 90 into the dishwasher automatically a feature that cuts space and reduces labor dramatically. Your dishroom team will appreciate this feature. Extended Hood Vent Hood C-Line Dishwashers are available with vent hoods or extended hoods, each with vent stack and lockingtype damper, and both designed to fit either end of the dishwasher. Conveyor Drive H.P. 1 6 Blower-Dryer - Motor H.P. (if used) 2 Electric Blower Dryer Heating Coils (if used) 42.0 KW Blower-Dryer - Based on 20 PSI Flowing Steam if used (25 PSIG MAX.) 110 Number of Tanks 1 Tank Capacity - Gallons 23.0 Pump Capacity - Gallons per Minute - Weir Test 151 104 Heating Equipment - (For keeping power wash hot) Gas Burners (with Natural Gas) - BTU per hr. 78,000 Steam Injectors Regulated 3 4" Electric Heating Unit - Size Used Regulated 15 KW Optional Booster Heater / Final Rinse 15 KW / 30 KW Rinse - Minutes operated during hour of maximum operation 60 Final Rinse Flow - Gals. per min. At 15 PSI Flow Pressure 1.83 At 20 PSI Flow Pressure 2.13 Final Rinse Flow - Gals. per hr. - MAXIMUM At 15 PSI Flow Pressure 110 At 20 PSI Flow Pressure 128 Rinse 20 PSI Flow Pressure Gal./Rack Hot Water Sanitizing - Chemical Sanitizing.64-180 F.64-140 F Steam Consumption - Pounds per hr. - MAXIMUM Approx. 30 lbs. per hr. = 1 boiler H.P. (BHP) Dishwasher, based on 20 PSI steam and on customersupplying final rinse water at 180 F maximum 65 Steam Booster, if used on 20 PSI steam - 20 PSI water flowing - 130 F entering water raised to 180 F min. 60 Exhaust Requirements - Cubic Feet per minute Entrance End 200 Discharge End 400 Discharge end w/blower Dryer 1400 Peak Rate of Drain Flow - Gallons per minute. (Initial rate with full tank) 38 Shipping Weight Crated - Approximate lbs. 613 F-39950 C44A Dishwasher Page 3 of 12
C44A DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com Page 4 of 12 F-39950 C44A Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C44A DISHWASHER F-39950 C44A Dishwasher Page 5 of 12
C44A ELECTRIC L-R 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com Page 6 of 12 F-39950 C44A Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C44A ELECTRIC R-L F-39950 C44A Dishwasher Page 7 of 12
C44A GAS L-R 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com Page 8 of 12 F-39950 C44A Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C44A GAS R-L F-39950 C44A Dishwasher Page 9 of 12
C44A STEAM L-R 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com Page 10 of 12 F-39950 C44A Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com C44A STEAM R-L F-39950 C44A Dishwasher Page 11 of 12
C44A DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com SPECIFICATIONS: Meets requirements of A.S.S.E. Standard No. 1004. DESIGN: Fully automatic, high-temperature single-tank, racktype dishwasher with flexible strip curtains at ends of chamber and between wash and final rinse compartments. Large inspection door located in front of machine provides easy access to wash arms, rinse arms, rinse pan strainer, strainer basket, front and rear strainers, and pump intake screen. Door guided for ease of operation and long life. Design provides for changing of direction of operation in the field. Length of machine inside tank (at table connection) 44". Machine designed to clean and sanitize with hot water 160 F wash and 180 F (minimum) final rinse. Water hardness must be controlled to 4-6 gr. for best results. Automatic interlocks shut off pump and conveyor if door is opened when machine is in operation. CONSTRUCTION: Tank and chamber constructed of #16 gauge stainless steel, arc-welded. Unitized, welded stainless steel tank, frame and stainless steel legs. Chamber, control box, door, and front trim panel are polished, satin finish. PUMP: Recirculating stainless steel pump with stainless steel impeller and face seal with stainless steel metal components and ceramic seat. Readily removable motor/impeller assembly permits quick inspection. The pump is self-draining. All piping distributing water to the upper and lower wash arms is stainless steel tubing. PUMP MOTOR: Built for Hobart: 2 horsepower, grease-packed ball bearings, splashproof, ventilated with manual resettable inherent overload protection. Available in electrical specifications of 208-240/60/1, 208-240/60/3, 480/60/3. Also available are 200-240/50/1, 200-240/50/3, 380-415/50/3, and 600/60/3, not submitted for UL Listing. CONTROLS: A stainless steel control center with power on/off and start/stop switches is mounted on top of machine. Machine control circuitry components will be operated from a 120 volt control circuit transformer. Auto-timer is standard equipment. An auto/manual switch is located on the left side of control box for bypassing the auto-timer feature. Electrical components are completely wired with 105 C, 600V thermoplastic insulated wire with stranded conductors routed through Listed electrical conduit or covered wireway built into the front of the machine above tank water level. CONVEYOR: Dual rack drive, with stainless steel pawls both sides of conveyor, designed to eliminate interference with wash and rinse spray patterns. Racks conveyed automatically through wash and rinse sections and onto clean dish table. Factory set overload mechanism on conveyor drive prevents damage to machine or racks, should movement of racks be obstructed. Rack tracks, conveyor structure, and drive units of stainless steel for 19 3 4" x 19 3 4" racks as standard. Conveyor speed: 5.6 FPM. DRIVE MOTOR: Built for Hobart, 1 6 horsepower gearmotor, ventilated with manual, resettable inherent overload protection. Available in electrical specifications of 208-240/60/1, 208-240/60/3, 480/60/3. Also available, but not submitted for UL Listing are 200-240/50/1, 200-240/50/3, and 380-415/50/3. POWER WASH: Wash tank is equipped with upper and lower stainless steel wash arms with specially shaped nozzles having large openings and arranged to effectively direct water jets to all ware surfaces. Both upper and lower wash arms, along with wash arm end caps, are easily removable for cleaning without use of tools. Removable perforated stainless steel strainer pans support a deep perforated stainless steel basket. Basket and strainer pans (2) can be removed without lower wash arm removal. FINAL RINSE: Stainless steel upper and lower rinse arms have single rows of nozzles. Rinse is automatically activated by racks in passing. Final rinse water line is equipped with vacuum breaker in downstream side of electrically operated solenoid valve in common piping system. Design provides for collection and division of final rinse water after use to wash tank and drain. Rinse agent dispenser injection port provided in final rinse piping above chamber. Final rinse flow rate: 2.13 GPM. Low Temp Final Rinse Sanitizer agent (5.25% sodium hypochlorite bleach) and rinse agent dispenser injection ports provided in final rinse piping above chamber. Caution: Certain materials, including silver, aluminum, and pewter are attacked by sodium hypochlorite (bleach) in the chemical sanitizing dishwasher mode of operation. FILL: Fill water line is equipped with vacuum breaker on downstream side of electrically operated solenoid valve in common piping system, for automatic maintenance of tank level. Fill is interrupted whenever a door is opened. DRAIN AND OVERFLOW: Large bell-type automatic overflow and drain valve controlled from inside of machine. Drain automatically closed by lowering inspection door. Drain seal is large diameter, high temperature o-ring. Stainless steel drain seat. Drain casting can be plumbed from load or unload end of machine. STANDARD EQUIPMENT: Sealed dial-type thermometers indicate temperatures of wash and final rinse water. Positive low water protection for tank heat. Plastic strip curtains throughout machine. Stainless steel control box. Built-in wireway. Drain is automatically closed when inspection door is closed. Stainless steel adjustable feet. Stainless steel hang-on/drop-in-place front trim panel. Automatic tank fill. Door interlock. Auto-timer. Vent fan and booster heater controls. WASH TANK HEATING SELECTIONS (must choose one): ELECTRIC: One electric incoloy sheathed immersion heater (15 KW) removable from inside tank. Tank water temperature is controlled by solid-state thermostat with positive low-water protection and magnetic contactor. (Disconnect switches not furnished.) Heating element is additionally protected by a high limit device mounted on the surface of the element. STEAM: One-inch stainless steel steam injector or one-inch stainless steel steam coils (for contaminated steam). Tank water temperature controlled by solid-state thermostat with positive low-water protection. Steam supplied to machine through high temperature steam solenoid valve and line strainer. GAS: Regulated power immersion tube gas burner system. Tank water temperature is controlled by solid-state thermostat and a blower with a centrifugal switch. Positive low water protection is provided. Immersion tube is additionally protected by a high limit device mounted on the surface of the tube. A solid-state ignitor board controls the gas valve and provides flame ignition. A transformer steps the control circuit voltage down from 120 volts to 24 volts to power the ignitor board and gas valve. For natural gas, gas pressure to burner (customer connection) not to exceed 7" W.C. For LP gas, gas pressure to burner (customer connection) not to exceed 11" W.C. If gas pressure is higher than 7" W.C. natural or 11" W.C. LP, a pressure regulating valve must be supplied (by others) in the gas line to the dishwasher. OPTIONAL EQUIPMENT AT EXTRA COST: Stainless steel pressureless booster heater. Stainless steel vent hoods with vent stack and locking-type damper. Stainless steel extended hoods with vent stack and locking type damper. SL-23 and SL-30 side loaders without hood. Six inches higher than standard. Steam or electric blower dryer (3-phase only). Floormounted steam booster. 19 3 4" x 19 3 4" peg and combination and miscellaneous racks. Single-point electrical connection for electric heat machines (3-phase only, does not include booster heater). Conveyor dwell. Table limit switch. As continued product improvement is a policy of Hobart, specifications are subject to change without notice. Page 12 of 12 F-39950 C44A Dishwasher F-39950 (REV. 10/07) LITHO IN U.S.A. (H-01) Printed On Recycled Paper
Item # Quantity C.S.I. Section 11400 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com AM SELECT TALL DISHWASHER STANDARD FEATURES.74 gallons per rack final rinse water 58 racks per hour hot water sanitizing 65 racks per hour chemical sanitizing NSF pot and pan listed for 2-, 4- & 6- minute cycles Timed wash cycles for 1, 2, 4 or 6 minutes 27" door opening for 18" x 26" sheet pans or 60 quart mixing bowl Solid state, integrated controls with digital status indicators Self-draining, high efficiency stainless steel pump and stainless steel impeller Stainless steel drawn tank, tank shelf, chamber, trim panels, frame and feet Spring counterbalanced chamber with polyethylene guides Revolving, interchangeable upper and lower anti-clogging wash arms Revolving, interchangeable upper and lower rinse arms Slanted, self-locating, one-piece scrap screen and basket system Automatic fill Door actuated start Automatic drain closure Vent fan control External booster activation Delime cycle Service diagnostics NAFEM Data Protocol capable Straight-through or corner installation Hot water or chemical sanitation Sheet pan rack VOLTAGE 208-240/60/1 208-240/60/3 480/60/3 200-240/50/3* 380-415/50/3* *Not submitted for UL/CUL Listing MODEL AM15T OPTIONS AT EXTRA COST Gas heat Sense-A-Temp 70 F rise electric booster heater Single point electrical connection for booster equipped machines (3 phase only) ACCESSORIES 3 4" pressure regulator valve Peg rack Combination rack Sheet pan rack Splash shield for corner installations Flanged and seismic feet End of cycle audible alarm (field activated) Delime notification (field activated) Drain water tempering kit Specifications, Details and Dimensions on Inside and Back. AM SELECT TALL DISHWASHER F-40079 AM Select Tall Dishwasher Page 1 of 8
AM SELECT TALL DISHWASHER ELECTRIC 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com Page 2 of 8 F-40079 AM Select Tall Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com AM SELECT TALL DISHWASHER ELECTRIC F-40079 AM Select Tall Dishwasher Page 3 of 8
AM SELECT TALL DISHWASHER GAS 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com Page 4 of 8 F-40079 AM Select Tall Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com AM SELECT TALL DISHWASHER GAS F-40079 AM Select Tall Dishwasher Page 5 of 8
AM SELECT TALL DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com ELECTRIC TANK HEAT GAS TANK HEAT Hot Water Sanitizing AM Select Tall Chemical Sanitizing Machine Ratings (Mechanical) Racks per Hour (Max.) 58 65 Dishes per Hour (Average 25 per rack) 1,459 1,625 Glasses per Hour (Average 45 per rack) 2,610 2,925 Table to Table - Inside Tank at Table Connection (Inches) 25 1 4" 25 1 4" Overall Dimensions - (H x W x D) (Inches) 77.5" x 27" x 28.5" Wash Motor H.P. 2 2 Wash Tank Capacity - Gallons 14 14 Wash Pump Capacity - Gallons per Minute - Weir Test 160 160 Heating Equipment - (For keeping power wash water hot) Gas Burner (Regulated) Natural/LP Gas BTU/Hr. 25,000 25,000 Electric Heating Unit (Regulated) 5 kw 5 kw Rinse - Minutes operated during hour of capacity operation 9.66 10.83 Seconds of rinse per rack 10 10 Rate of Rinse Flow - Gallons per Minute - at 20 lbs. Flow Pressure 4.4 4.4 Rinse Consumption - Gallons per Hour - Maximum - at 20 lbs. Flow Pressure 42.9 48.1 Rinse Cycle - Gallons per Rack - at 20 PSI Flow.74-180 F Min..74-140 F Min. Steam Booster, if used based on 20 PSI steam - 20 PSI water flowing 130 F entering water raised to 180 F min. (50 F rise) - Lbs. per Hour 40 40 Peak Rate of Drain Flow - Gallons per Minute (Initial rate with full tank) 38 38 Exhaust Requirements 450 450 Shipping Weight Crated - Approx. lbs. - Unit only, with booster 388 w/o Booster 418 w/booster 388 Page 6 of 8 F-40079 AM Select Tall Dishwasher
701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com AM SELECT TALL DISHWASHER F-40079 AM Select Tall Dishwasher Page 7 of 8
AM SELECT TALL DISHWASHER 701 S Ridge Avenue, Troy, OH 45374 1-888-4HOBART www.hobartcorp.com The microcomputer-based control system is built into the AM Select dishwasher. It is available in standard electrical specifications of 208-240/60/1, 208-240/60/3, 480/60/3, 200-240/50/3, 380-415/50/3 and is equipped with a reduced voltage pilot circuit transformer. *CAUTION: CERTAIN MATERIALS, INCLUDING SILVER, ALUMINUM AND PEWTER ARE ATTACKED BY SODIUM HYPOCHLORITE (LIQUID BLEACH) IN THE CHEMICAL SANITIZING DISHWASHER MODE OF OPERATION. WATER HARDNESS MUST BE CONTROLLED TO 4-6 GRAINS FOR BEST RESULTS. CONSTRUCTION: Drawn tank, tank shelf and feet constructed of 16 gauge stainless steel. Wash chamber and front trim panel above motor compartment are polished, satin finish. Frame is 12 gauge stainless steel, chamber is 18 gauge, and removable trim panels are 20 gauge. CHAMBER: Stainless steel chamber with large 20 3 4" W x 27" H opening will accommodate 18" x 26" sheet pans or a 60-quart mixing bowl. CHAMBER LIFT: Chamber coupled by stainless steel handle, spring counterbalanced. Chamber guided for ease of operation and long life. PUMP: With stainless steel pump and impeller, integral with motor assures alignment and quiet operation. Pump shaft seal with stainless steel parts and a carbon ceramic sealing interface. Easily removable impeller housing permits ease of inspection. Capacity 160 GPM. Pump is completely self-draining. MOTOR: Built for Hobart, 2 H.P., with inherent thermal protection, grease-packed ball bearings, splash-proof design, ventilated. Single-phase is capacitor-start, induction-run type. Three-phase is squirrel-cage, induction type. MICROCOMPUTER CONTROL SYSTEM: Hobart microcomputer controls, assembled within water-resistant enclosure, provide built-in performance and reliability. The microcomputer control, relays and contactors are housed behind a stainless steel enclosure, hinged to provide easy access for servicing. The line voltage electrical components are completely wired with 105 C, 600V thermoplastic insulated wire with stranded conductors and routed through listed electrical conduit. Electrical components are wired with type ST cord. Line disconnect switch NOT furnished. CYCLE OPERATION: The microcomputer-timing program is started by closing the doors, which actuates the door cycle switch. The microcomputer energizes the wash pump motor contactor during the wash portion of the program. After the wash, a dwell permits the upper wash manifold to drain. At the end of the dwell, the final rinse solenoid valve is energized. After the final rinse valve closes, Sani-Dwell (Hot Water Mode only) permits sanitization to continue. The Rinse display remains on during this period, completing the program. If the microcomputer is interrupted during a cycle by the door-cycle switch, the microcomputer is reset to the beginning of the program. Hot Water Sanitizing (58 racks per hour) 57 seconds: 38 Second Wash, 2 Second Dwell, 10 Second Rinse, 7 Second Sani-Dwell. Chemical Sanitizing (65 racks per hour) 50 Seconds: 38 Second Wash, 2 Second Dwell, 10 Second Rinse. Other programs can be pre-selected by your Hobart service technician. Manual wash cycle selector also provides selection of 2-, 4- or 6-minute wash cycles for heavier washing applications. WASH: Hobart revolving stainless steel wash arms with unrestricted openings above and below provide thorough distribution of water jets to all dishware surfaces. Arms are easily removable for cleaning and are interchangeable. Stainless steel tubing manifold connects upper and lower spray system. RINSE: Rotating rinse arms, both upper and lower, feature 14 rinse nozzles. The stainless steel upper and lower rinse arms are easily removable without tools for inspection and are interchangeable. Diaphragm-type rinse control solenoid valve mounted outside machine. Machine is equipped with special hot water vacuum breaker on downstream side of rinse valve mounted 6" above uppermost rinse opening. Easy open brass line strainer furnished. FILL: Microcomputer controlled fill valve installed on upstream side of rinse vacuum breaker. Ratio fill method is used giving the correct fill at any flowing water pressure. (20 PSIG minimum necessary for proper rinsing.) DRAIN AND OVERFLOW: Large bell type automatic overflow and drain valve controlled from inside of machine. Drain automatically closed by lowering chamber. Drain seal is large diameter, high temperature O ring. Cover for overflow is integral part of the stand pipe. STRAINER SYSTEM: Equipped with large, exclusive selfflushing, easily removable perforated stainless steel, one-piece strainer and large capacity scrap basket. Submerged scrap basket minimizes frequent removal and cleaning. HEATING EQUIPMENT: Standard tank heat is 5KW electric immersion heating element. Regulated power infrared gas immersion tube system is optional at extra cost. A solid-state igniter board controls the gas valve and provides flame ignition. A transformer steps the control circuit voltage down to 24 volts to power the igniter board and gas valves. Gas Heated Dishwasher: For natural gas, gas pressure (customer connection) not to exceed 7" W.C. For liquefied petroleum, gas pressure to burner (customer connection) not to exceed 11" W.C. If gas pressure is higher than 7" W.C. natural or 11" W.C. LP, a pressure regulating valve must be supplied (by others) in the gas line to the dishwasher. Water temperature regulation is controlled by thermistor sensor in combination with microcomputer controls. The tank heat and positive low water protection microcomputer circuits are automatically activated when the main power switch is turned on. If tank is accidentally drained, low water protection device automatically turns heat off. Gas immersion tube is additionally protected by a high limit device mounted on the surface of the tube. These features are standard with the Hobart Microcomputer Control System. OPTIONAL EQUIPMENT AT EXTRA COST ELECTRIC BOOSTER HEATER: Electric booster with Sense-A-Temp TM technology adequately sized to raise 110 F inlet water to 180 F (not available on gas heat machines). ACCESSORIES: 19 3 4" x 19 3 4" peg and combination dish racks. Sheet pan rack. Splash shield for corner installations. End of cycle audible alarm (field activated). Delime notification (field activated). Desirable functional accessories can be furnished at added cost. See listed options and accessories on this specification sheet. Write to the factory for special requirements not listed above. As continued product improvement is a policy of Hobart, specifications are subject to change without notice. Page 8 of 8 F-40079 AM Select Tall Dishwasher F-40079 (REV. 10/07) LITHO IN U.S.A. (H-01) Printed On Recycled Paper
Item No. Project Quantity 12 Adder Section for 36 Ranges Model: 36S-[12,14] CONSTRUCTION FEATURES One piece heavy duty 430 Series stainless steel exterior, with attractive No. 4 finish 6 adjustable legs standard 2 high range top back riser 3 wide full width front grease trough 6 wide full width plate landing Grease drain in trough with full width & depth spillage drawers Model 36S-12 shown CONFIGURATION GUIDE* Model Has: 36S-12 36S-14 French Plates: - 2 each Hot Plates: 1 each - Pictogram: [Unit Top View] PERFORMANCE FEATURES Unit expands productivity of 36 Range, when space is available Choice of cook top configurations, to include: 1 ea. 12 wide Hot Tops 2 ea. 8 diameter French Plates Full front grease trough, grease drain & spillage drawers speed cleanup Full front landing simplifies and speeds plating Separate, independent controls allows simultaneous multi-function cooking CONTROLS [Varies By Top Configuration] [-12] One 450 F thermostat for Hot Top [-14] Two 6-heat level switches [ea. French Plate] * See other side for additional spreader options. SHORT/BID SPECIFICATION Adder Range Section shall be a LANG Manufacturing Model 36S- [Specify one]: -12, with 1 ea. 12 X 24 X 3/4 thick Hot Plate; or -14, with 2 ea. 8 diameter French Plates a 12 wide heavy-duty electric heated unit designed to match 36 wide gas or electric Lang Range models; with all stainless steel exterior; individual cook-top component controls; plus the features listed and options/accessories checked: STANDARD PRODUCT WARRANTY One year, parts & labor Sheet No. LSP-R6 (rev. 9/03) LANG MANUFACTURING COMPANY 6500 Merrill Creek Parkway, Everett, WA 98203 TOLL FREE: 800.882.6368 FAX: 425.349.2733 www.langworld.com
12 Adder Section for 36 Ranges Model: 36S-[12,14] INSTALLATION REQUIREMENTS E Single 208/240V, 1/ 3-Phase; or 480V, 3-phase electrical connection Installation under approved vent hood required. Consult local codes. OPTIONS & ACCESSORIES Substitute a Griddle with 12 X 24 X 3/4 thick plate, w/splash guard Substitute 1 thick griddle plate for grooving [12 wide] Grooving on [1 thick ONLY] that Griddle Plate Substitute Open Coil Units for French Plates [208/240V ONLY] 480 Volt, 3-phase model [Power connection from bottom. See below] 6 wide Top Spreader to bank with 36 Ranges 12 wide Top Spreader to bank with 36 Ranges 6 wide Front Enclosure, for use with 6 Top Spreader 12 wide Front Enclosure, for use with 12 Top Spreader 12.0" 305mm 38.1" 968mm 12.0" 305mm 32.2" 818mm 37.1" 944mm 38.1" 968mm 6.0"/153mm E ELECTRIC CONNECTION 2.9" 73mm 6.3" 160mm 5.0"/127mm 2.9" 73mm 2.9" 73mm 8.0"/204mm E ELECTRIC CONNECTION 29.3" 744mm 2.9" 73mm [Front View/Elevation] [Right Side View] [36S-12 shown in Top View/Plan] Model Height x Width x Depth Clearance from Weight Freight (With standard legs) combustible surface Actual Shipping Class 36S-12 36S-14 130 lbs. 160 lbs. 37.1 x 12.0 x 38.1 Sides: 4 (100mm) 59 kg 73 kg 944mm x 305mm x 968mm Back: 4 (100mm) 90 lbs. 120 lbs. 41 kg 55 kg Model E Electrical Requirements Voltage Total kw Phase Amps/Line 208V/60Hz 5.0 1 24.0 36S-12 240V/60Hz 5.0 1 20.8 480V/60Hz 5.0 1 10.4 208V/60Hz 5.2 1 25.0 36S-14 240V/60Hz 5.2 1 21.7 480V/60Hz 5.2 1 10.8 CAD SYMBOLS & PRICING 85 Due to continuous improvements, specifications subject to change without notice. Sheet No. LSP-R6 (rev. 9/03) LANG MANUFACTURING COMPANY 6500 Merrill Creek Parkway, Everett, WA 98203 TOLL FREE: 800.882.6368 FAX: 425.349.2733 www.langworld.com 2003 Lang Manufacturing Company Printed in U.S.A. 9/03-M-12198
http://www.edlundco.com/catalog/product.cgi/3/4/5/67/p1/default/n/0 Page 1 of 1 5/13/2008 Full Line Manual Electric Crown Punch Parts & Accessories Can Opener Reference Chart Full Line Manual Electric Hydraulic Air Powered Full Line Mechanical Portion Control Mechanical Receiving Digital Specialty The Importance of Portion Control Full Line Knife Sharp Stainless Kn Knife Racks Knife Sanitiz Tongs Can Punch and Bottle Openers Scales Parts & Accessories Electric Slic S-11 Manual Can Opener Back to Product Line Product Code: 15000 Stainless Steel Can Opener (NSF Certified) with cast stainless steel base Model No.: S-11 Case Cube Ft³/M³: 3.3/.1 Master Case: 3 Case Weight lbs/kgs: 30/13.6 view larger image Quantity: 1 2008 The Edlund Company
Project Quantity Item # Model Specified: CSI Section 11400 G-Series Reach-In Refrigerators/ Self-Contained Equipped with an easy to use microprocessor control! G SERIES Stainless Steel Front & Door(s) One, Two & Three Section Models, 32" Deep Aside from their anodized aluminum side and interior finishes, Traulsen s G-Series "Dealer's Choice" models meet or exceed the standard specifications and performance of most other brands top tier product offerings. Reliable, energy efficient, and durable, with large individual storage capacities, the high quality G-Series line-up includes a wide range of one, two and three section reach-in refrigerator and freezer models, built in our most popular footprints. They are available with either full or half height doors, and the added convenience of a variety of different door hingings to choose from. In addition, each also includes a number of user-friendly features, making them one of the best overall equipment values in Foodservice today, and the right fit for nearly any commercial application. Model G30010 Model G20010 Model G10010 Standard Product Features High Quality Stainless Steel Exterior Front and Door(s) Corrosion Resistant Anodized Aluminum One-Piece Sides Durable Anodized Aluminum Interior Microprocessor Control With LED Temperature Readout Top-Mounted, Balanced, Self-Contained Refrigeration System Large High Humidity Evaporator Coil Outside The Food Zone Full or Half Length Stainless Steel Doors With Locks Self-Closing Doors With Stay Open Feature At 120 Degrees Guaranteed For Life Cam-Lift Hinges Guaranteed For Life Horizontal Work Flow Door Handle(s) Automatically Activated Incandescent Lights Damage Resistant Stainless Steel Breaker Caps Three (3) Adjustable Epoxy Coated Shelves Per Section, Supported On Shelf Pins (installed at the factory) Energy Saving Automatic Non-Electric Condensate Evaporator Magnetic Snap-In Door Gaskets Gasket Protecting Anodized Aluminum Door Liner Anti-Condensate Door Perimeter Heaters Thermostatic Expansion Valve Metering Device Provides Quick Refrigeration Recovery Times Stainless Steel One-Piece Louver Assembly 9' Cord & Plug Attached Set of Four (4) 6" High Casters With Locks One Year Parts And Labor Warranty Five Year Compressor Warranty AVAILABLE MODELS Single Section Two Section Three Section (Formerly Model GHT132WUT) (Formerly Model GHT232NUT) (Formerly Model GHT332NUT) Model # Door Hinging Model # Door Hinging Model # Door Hinging G10000 Half Right G20000 Half Left-Right G30000 Half Left-Right-Right G10001 Half Left G20001 Half Right-Left G30001 Half Left-Left-Right G10010 Full Right G20002 Half Right-Right G30002 Half Right-Right-Right G10011 Full Left G20003 Half Left-Left G30003 Half Left-Left-Left G20010 Full Left-Right G30010 Full Left-Right-Right G20011 Full Right-Left G30011 Full Left-Left-Right G20012 Full Right-Right G30012 Full Right-Right-Right G20013 Full Left-Left G30013 Full Left-Left-Left Optional Accessory Kits Additional Epoxy Coated Shelves* No. 1 Type Tray Slides* To Accommodate either: (1) 18" x 26" or (2) 14" x 18" Sheet Pans, Adjustable To 2" O.C. No. 4 Type Tray Slides* To Accommodate (1) 18" x 26" Sheet Pans (equips one full section) Universal Type Tray Slides* To Accommodate Either (1) 18" x 26" or (2) 14" x 18" Sheet Pans, or (2) 12" x 20" Steam Table Pans, Adjustable To 4" O.C. Chrome Plated Shelves* (for use in lieu of standard shelving) 6" High Adjustable Legs (for use in lieu of standard casters) Two Year Service/Labor Warranty Available NOTE: *Please refer to spec sheet 4-5 for optional accessory kit details All optional accessory kits are shipped separately for later installation by others at the jobsite. All Traulsen G-Series solid door refrigerator models are ENERGY STAR listed for efficient operation! Listed by Underwriters Laboratories Inc., to U.S. and Canadian safety standards and Listed by NSF International. Approval: TRAULSEN 4401 BLUE MOUND RD. FT. WORTH, TX 76106 PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302 Website: www.traulsen.com SECTION 4-1
Project Quantity Item # Model Specified: CSI Section 11400 Construction, Hardware and Insulation Cabinet exterior front, louver assembly and doors are constructed of 20 gauge stainless steel. Cabinet sides (including returns), interior and door liners are constructed of anodized aluminum. The exterior cabinet top, back and bottom are constructed of heavy gauge aluminized steel. A set of four (4) 6" high casters are included. Doors are equipped with a gasket protecting metal door pan, removable plug cylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glide hinges with stay open feature at 120 degrees. Hinges include a concealed switch to automatically activate the interior incandescent lighting. Guaranteed for life, work flow door handles are mounted horizontally over recess in door which limits protrusion from door face into aisleways. Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal. Anti condensate heaters are located behind each door opening. Both the cabinet and door(s) are insulated with an average of 2" thick high density, non-cfc, foamed in place polyurethane. DIMENSIONAL DATA 1-Section Models 2-Section Models 3-Section Models Net capacity cu. ft. 24.2 (686 cu l) 46.0 (1303 cu l) 69.1 (1958 cu l) Length - overall in. 29 7 8 (75.9 cm) 52 1 8 (132.4 cm) 76 5 16 (193.8 cm) Depth - overall in. 35 (88.8 cm) 35 (88.8 cm) 35 (88.8 cm) Depth - over body in. 32 (81.3 cm) 32 (81.3 cm) 32 (81.3 cm) Depth - door open 90 in. 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) Clear door width in. 21 1 8 (53.6 cm) 21 1 8 (53.6 cm) 21 1 8 (53.6 cm) Clear half-door height in. 27 1 2 (69.9 cm) 27 1 2 (69.9 cm) 27 1 2 (69.9 cm) Clear full-door height in. 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) Height-overall on 6" casters 83 1 4 (211.5 cm) 83 1 4 (211.5 cm) 83 1 4 (211.5 cm) No. Standard Shelves 3 6 9 Shelf area sq. ft. 1 18.8 (1.75 sq m) 34.6 (3.21 sq m) 51.9 (4.82 sq m) ELECTRICAL DATA Voltage 115/60/1 115/60/1 115/60/1 Feed wires with Ground 3 3 3 Full load amperes 7.0 8.5 10.9 REFRIGERATION DATA Refrigerant R-134a R-134a R-134a BTU/HR H.P. 2 2400 ( 1 3 HP) 2400 ( 1 3 HP) 4360 ( 1 2 HP) SHIPPING DATA Length - crated in. 35 (89 cm) 63 (160 cm) 91 (231 cm) Depth - crated in. 43 (109 cm) 43 (109 cm) 43 (109 cm) Height - crated in. 83 1 2 (212 cm) 83 1 2 (212 cm) 83 1 2 (212 cm) Volume - crated cu. ft. 71 (2011 cu l) 131 (3711 cu l) 189 (5354 cu l) Net Wt. lbs. 305 (138 kg) 450 (204 kg) 610 (277 kg) Gross Wt. lbs. 395 (179 kg) 590 (268 kg) 790 (358 kg) Specifications Refrigeration System A top mounted, self-contained, balanced refrigeration system using R-134a refrigerant is conveniently located behind the one piece louver assembly. It features an easy to clean front facing condenser, thermostatic expansion valve, air-cooled hermetic compressor, large, high humidity evaporator coil located outside the food zone and a top mounted non-electric condensate evaporator. A 9' cord and plug is provided. Standard operating temperature is 34 to 38 F. Controller The easy to use water resistant microprocessor control system is supplied standard. It includes a 3-Digit LED Display, and a Fahrenheit or Celsius Temperature Scale Display Capability. Interior Standard interior arrangements include three (3) epoxy coated wire shelves per section, mounted on shelf pins, installed at the factory. Shelves are full-width, and do not have any large gaps between them requiring the use of "bridge" or "junior shelves." Recommended load limit per shelf should not exceed 225 lbs. Warranties Both a one year parts and labor warranty and a five year compressor warranty (selfcontained models only) are provided standard. An optional 2 nd year extended parts and labor warranty is also available. Elevation One-Section Elevation Two-Section Elevation Three-Section NOTES NOTE: Figures in parentheses reflect metric equivalents. 1= Figure shown reflects the area of standard shelf compliment plus the additional storage area available on the cabinet bottom. 2= Based on a 90 degree F ambient and 20 degree F evaporator. Plan - One-Section Plan - Two-Section Equipped With One NEMA 5-15 P Plug REQUIRED CLEARANCES In order to assure optimum performance, the condensing unit MUST have an adequate supply of air for cooling purposes. Therefore, the operating location must either have a minimum of 12 clearance overhead of the condensing unit or allow for unrestricted air flow at the back of the unit. Clearance of at least 12 above is required in order to perform certain maintenance tasks. NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options and any additional warranties. Continued product development may necessitate specification changes without notice. Part No. TR35787 (revised 1/07) Plan - Three-Section Section - All Models SECTION 4-1 TRAULSEN 4401 BLUE MOUND RD. FT. WORTH, TX 76106 PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302 Website: www.traulsen.com
Project Quantity Item # Model Specified: CSI Section 11400 G-Series Reach-In Freezers/ Self-Contained Equipped with an easy to use microprocessor control! G SERIES Stainless Steel Front & Door(s) One, Two & Three Section Models, 32" Deep Aside from their anodized aluminum side and interior finishes, Traulsen s G-Series "Dealer's Choice" models meet or exceed the standard specifications and performance of most other brands top tier product offerings. Reliable, energy efficient, and durable, with large individual storage capacities, the high quality G-Series line-up includes a wide range of one, two and three section reach-in refrigerator and freezer models, built in our most popular footprints. They are available with either full or half height doors, and the added convenience of a variety of different door hingings to choose from. In addition, each also includes a number of user-friendly features, making them one of the best overall equipment values in Foodservice today, and the right fit for nearly any commercial application. Model G31310 Model G22010 Model G12010 Standard Product Features High Quality Stainless Steel Exterior Front and Door(s) Corrosion Resistant Anodized Aluminum One-Piece Sides Durable Anodized Aluminum Interior Microprocessor Control With LED Temperature Readout Top-Mounted, Balanced, Self-Contained Refrigeration System Large High Humidity Evaporator Coil Outside The Food Zone Full or Half Length Stainless Steel Doors With Locks Self-Closing Doors With Stay Open Feature At 120 Degrees Guaranteed For Life Cam-Lift Hinges Guaranteed For Life Horizontal Work Flow Door Handle(s) Automatically Activated Incandescent Lights Damage Resistant Stainless Steel Breaker Caps Three (3) Adjustable Epoxy Coated Shelves Per Section, Supported On Shelf Pins (installed at the factory) Energy Saving Automatic Non-Electric Condensate Evaporator Magnetic Snap-In Door Gaskets Gasket Protecting Anodized Aluminum Door Liner Anti-Condensate Door Perimeter Heaters Thermostatic Expansion Valve Metering Device Provides Quick Refrigeration Recovery Times Stainless Steel One-Piece Louver Assembly 9' Cord & Plug Attached Set of Four (4) 6" High Casters With Locks One Year Parts And Labor Warranty Five Year Compressor Warranty AVAILABLE MODELS Single Section Two Section Three Section (Formerly Model GLT132WUT) (Formerly Model GLT232NUT) (Formerly Model GLT332NUT) Model # Door Hinging Model # Door Hinging Model # Door Hinging G12000 Half Right G22000 Half Left-Right G31300 Half Left-Right-Right G12001 Half Left G22001 Half Right-Left G31301 Half Left-Left-Right G12010 Full Right G22002 Half Right-Right G31302 Half Right-Right-Right G12011 Full Left G22003 Half Left-Left G31303 Half Left-Left-Left G22010 Full Left-Right G31310 Full Left-Right-Right G22011 Full Right-Left G31311 Full Left-Left-Right G22012 Full Right-Right G31312 Full Right-Right-Right G22013 Full Left-Left G31313 Full Left-Left-Left Optional Accessory Kits Additional Epoxy Coated Shelves* No. 1 Type Tray Slides* To Accommodate either: (1) 18" x 26" or (2) 14" x 18" Sheet Pans, Adjustable To 2" O.C. No. 4 Type Tray Slides* To Accommodate (1) 18" x 26" Sheet Pans (equips one full section) Universal Type Tray Slides* To Accommodate Either (1) 18" x 26" or (2) 14" x 18" Sheet Pans, or (2) 12" x 20" Steam Table Pans, Adjustable To 4" O.C. Chrome Plated Shelves* (for use in lieu of standard shelving) 6" High Adjustable Legs (for use in lieu of standard casters) Two Year Service/Labor Warranty Available NOTE: *Please refer to spec sheet 4-5 for optional accessory kit details All optional accessory kits are shipped separately for later installation by others at the jobsite. All Traulsen G-Series solid door freezer models are ENERGY STAR listed for efficient operation! Listed by Underwriters Laboratories Inc., to U.S. and Canadian safety standards and Listed by NSF International. Approval: TRAULSEN 4401 BLUE MOUND RD. FT. WORTH, TX 76106 PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302 Website: www.traulsen.com SECTION 4-2
Project Quantity Item # Model Specified: CSI Section 11400 Construction, Hardware and Insulation Cabinet exterior front, louver assembly and doors are constructed of 20 gauge stainless steel. Cabinet sides (including returns), interior and door liners are constructed of anodized aluminum. The exterior cabinet top, back and bottom are constructed of heavy gauge aluminized steel. A set of four (4) 6" high casters are included. Doors are equipped with a gasket protecting metal door pan, removable plug cylinder locks and guaranteed for life cam-lift, gravity action, self-closing metal, glide hinges with stay open feature at 120 degrees. Hinges include a concealed switch to automatically activate the interior incandescent lighting. Guaranteed for life, work flow door handles are mounted horizontally over recess in door which limits protrusion from door face into aisleways. Easily removable for cleaning, vinyl magnetic door gasket assures tight door seal. Anti condensate heaters are located behind each door opening. Both the cabinet and door(s) are insulated with an average of 2" thick high density, non-cfc, foamed in place polyurethane. DIMENSIONAL DATA 1-Section Models 2-Section Models 3-Section Models Net capacity cu. ft. 24.2 (686 cu l) 46.0 (1303 cu l) 69.1 (1958 cu l) Length - overall in. 29 7 8 (75.9 cm) 52 1 8 (132.4 cm) 76 5 16 (193.8 cm) Depth - overall in. 35 (88.8 cm) 35 (88.8 cm) 35 (88.8 cm) Depth - over body in. 32 (81.3 cm) 32 (81.3 cm) 32 (81.3 cm) Depth - door open 90 in. 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) Clear door width in. 21 1 8 (53.6 cm) 21 1 8 (53.6 cm) 21 1 8 (53.6 cm) Clear half-door height in. 27 1 2 (69.9 cm) 27 1 2 (69.9 cm) 27 1 2 (69.9 cm) Clear full-door height in. 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) 57 5 8 (146.3 cm) Height-overall on 6" casters 83 1 4 (211.5 cm) 83 1 4 (211.5 cm) 83 1 4 (211.5 cm) No. Standard Shelves 3 6 9 Shelf area sq. ft. 1 18.8 (1.75 sq m) 34.6 (3.21 sq m) 51.9 (4.82 sq m) ELECTRICAL DATA Voltage 115/60/1 115/60/1 208-230/115/60/1 Feed wires with Ground 3 3 4 Full load amperes 11.3 14.9 10.8 REFRIGERATION DATA Refrigerant R-404A R-404A R-404A BTU/HR H.P. 2 2160 ( 1 2 HP) 3790 ( 3 4 HP) 4710 (1 HP) SHIPPING DATA Length - crated in. 35 (89 cm) 63 (160 cm) 91 (231 cm) Depth - crated in. 43 (109 cm) 43 (109 cm) 43 (109 cm) Height - crated in. 83 1 2 (212 cm) 83 1 2 (212 cm) 83 1 2 (212 cm) Volume - crated cu. ft. 71 (2011 cu l) 131 (3711 cu l) 189 (5354 cu l) Net Wt. lbs. 320 (145 kg) 650 (295 kg) 690 (313 kg) Gross Wt. lbs. 410 (186 kg) 700 (318 kg) 870 (395 kg) Specifications Refrigeration System A top mounted, self-contained, balanced refrigeration system using R-404A refrigerant is conveniently located behind the one piece louver assembly. It features an easy to clean front facing condenser, thermostatic expansion valve, air-cooled, hermetic compressor, large, high humidity evaporator coil located outside the food zone and a top mounted non-electric condensate evaporator. A 9' cord and plug is provided. Standard operating temperature is 0 to -5 F. Controller The easy to use water resistant microprocessor control system is supplied standard. It includes a 3-Digit LED Display, and a Fahrenheit or Celsius Temperature Scale Display Capability. Interior Standard interior arrangements include three (3) epoxy coated wire shelves per section, mounted on shelf pins, installed at the factory. Shelves are full-width, and do not have any large gaps between them requiring the use of "bridge" or "junior shelves." Recommended load limit per shelf should not exceed 225 lbs. Warranties Both a one year parts and labor warranty and a five year compressor warranty (selfcontained models only) are provided standard. An optional 2 nd year extended parts and labor warranty is also available. Elevation One-Section Elevation Two-Section Elevation Three-Section NOTES NOTE: Figures in parentheses reflect metric equivalents. 1= Figure shown reflects the area of standard shelf compliment plus the additional storage area available on the cabinet bottom. 2= Based on a 90 degree F ambient and -20 degree F evaporator. Plan - One-Section Plan - Two-Section 1-Section Models equipped with one NEMA 5-15P Plug 3-Section Models equipped with one NEMA L14-20P Plug 2-Section Models equipped with one NEMA 5-20P Plug REQUIRED CLEARANCES In order to assure optimum performance, the condensing unit MUST have an adequate supply of air for cooling purposes. Therefore, the operating location must either have a minimum of 12 clearance overhead of the condensing unit or allow for unrestricted air flow at the back of the unit. Clearance of at least 12 above is required in order to perform certain maintenance tasks. NOTE: When ordering please specify: Voltage, Hinging, Door Size, Options and any additional warranties. Continued product development may necessitate specification changes without notice. Part No. TR35788 (revised 1/07) Plan - Three-Section Section - All Models SECTION 4-2 TRAULSEN 4401 BLUE MOUND RD. FT. WORTH, TX 76106 PHONE 1 (800) 825-8220 FAX-MKTG. 1 (817) 624-4302 Website: www.traulsen.com
Item# Job SUPER ERECTA SHELF WIRE SHELVING Unique Design: The open wire design of these heavy-gauge carbon-steel or stainless steel shelves minimizes dust accumulation and allows a free circulation of air, greater visibility of stored items and greater light penetration. Versatile Construction: Super Erecta Shelf wire shelving can change as quickly as your needs change. By using various accessories, hundreds of shelving configurations become possible. Fast, Secure Assembly: SiteSelect Posts with the triple-groove visual guide feature, have circular grooves at 1" (25mm) intervals and are numbered at 2" (50mm) intervals. A patented, tapered split sleeve (plastic or aluminum) snaps together around each post. Tapered openings in the shelf corners slide over the tapered split sleeves providing a positive lock. Shelf is assembled in minutes without the use of any special tools. Shelf Ribs: Run front to back, allowing you to slide items on and off shelves smoothly. Shelf Accessibility: Shelves can be loaded/unloaded easily from all sides. This open construction allows use of maximum storage space of cube. Adjustability: Shelves can be adjusted at 1 (25mm) intervals along the entire length of the post. Durable: Super Erecta Shelf wire shelving is available in four options: Super Erecta Brite, chrome-plated, stainless steel and Metroseal. Adjustable Feet: Bolt levelers compensate for surface irregularities. Wire Shelving Copyright 1993 InterMetro Industries Corporation InterMetro Industries Corporation North Washington Street Wilkes-Barre, PA 18705 www.metro.com Copyright 1997 Metropolitan Wire Corp. 10.01
10.01 Job SUPER ERECTA SHELF WIRE SHELVING WIRE SHELVES Split Sleeves SUPER ERECTA SHELF meets U.S. Government Specifications MIL-S- 40144E. PLATED SHELVING has clear protective coating. For load capacity guidelines, ask your InterMetro representative for a copy of Helpful Hints. Approx. Width Length Pkd. Wt. Cat. No. Cat. No. Cat. No. (in.) (mm) (in.) (mm) (lbs.) (kg) Super Erecta Brite Chrome Stainless 14 355 24 610 6 2.7 1424BR 1424NC 1424NS 14 355 30 760 7 3.2 1430BR 1430NC 1430NS 14 355 36 910 8 3.6 1436BR 1436NC 1436NS 14 355 42 1060 9 1 /2 4.3 1442BR 1442NC 1442NS 14 355 48 1220 10 1 /2 4.7 1448BR 1448NC 1448NS 14 355 60 1525 14 6.3 1460BR 1460NC 1460NS 14 355 72 1825 17 7.7 1472BR 1472NC 1472NS 18 455 24 610 7 3.2 1824BR 1824NC 1824NS 18 455 30 760 8 3.6 1830BR 1830NC 1830NS 18 455 36 910 9 1 /2 4.3 1836BR 1836NC 1836NS 18 455 42 1060 11 5.0 1842BR 1842NC 1842NS 18 455 48 1220 12 5.4 1848BR 1848NC 1848NS 18 455 54 1370 14 1 /2 6.6 1854BR 1854NC 1854NS 18 455 60 1525 17 7.7 1860BR 1860NC 1860NS 18 455 72 1825 20 9.1 1872BR 1872NC 1872NS 21 530 24 610 8 3.6 2124BR 2124NC 2124NS 21 530 30 760 9 4.1 2130BR 2130NC 2130NS 21 530 36 910 11 5.0 2136BR 2136NC 2136NS 21 530 42 1060 12 5.4 2142BR 2142NC 2142NS 21 530 48 1220 14 6.4 2148BR 2148NC 2148NS 21 530 54 1370 16 7.6 2154BR 2154NC 2154NS 21 530 60 1525 18 8.2 2160BR 2160NC 2160NS 21 530 72 1825 24 10.9 2172BR 2172NC 2172NS 24 610 24 610 9 4.1 2424BR 2424NC 2424NS 24 610 30 760 11 5.0 2430BR 2430NC 2430NS 24 610 36 910 13 5.9 2436BR 2436NC 2436NS 24 610 42 1060 15 6.8 2442BR 2442NC 2442NS 24 610 48 1220 16 7.3 2448BR 2448NC 2448NS 24 610 54 1370 18 8.6 2454BR 2454NC 2454NS 24 610 60 1525 21 9.5 2460BR 2460NC 2460NS 24 610 72 1825 26 11.8 2472BR 2472NC 2472NS NOTE: For Metroseal shelving information see sheet No. 10.10. Wire Shelving S Hooks Used to add-on shelving units with only two posts required. Cat. No. 9995Z SiteSelect Posts Approx. Height* Pkd. Wt. Cat. No. Cat. No. (in.) (mm) (lbs.) (kg) Plated Stainless 7 5 /8 190 1/2 0.2 7P 14 1 /2 368 1 0.5 13P 13PS 28 1 /2 724 1 3 /4 0.75 27P 27PS 34 1 /2 876 2 0.9 33P 33PS 54 9 /16 1386 3 1.4 54P 54PS 62 9 /16 1589 3 1 /2 1.6 63P 63PS 74 5 /8 1895 4 1.8 74P 74PS 86 5 /8 2200 5 2.3 86P 86PS *Height includes leveling bolt and cap. SiteSelect Posts are grooved at 1" (25mm) increments and numbered at 2" (50mm) increments. Posts are triplegrooved every 8" (203mm) for easy identification. Important: When ordering by components remember that stability decreases as the ratio of height to width increases. Units should be kept as wide and low as possible. With 14 shelving, foot plates should be used and secured to the floor on free-standing units; on mobile units, maximum post height is 54. Manufactured by: Phone 717-825-2741 InterMetro Industries Corp. FAX 717-825-2852 North Washington Street For Product Information, call 1-800-433-2232 Wilkes-Barre, PA 18705 For Customer Service, call 1-800-992-1776 InterMetro Industries Corporation North Washington Street Wilkes-Barre, PA 18705 www.metro.com L02-006 Rev. 3/98 BJ Printed in U.S.A. Information and specifications are subject to change without notice. Please confirm at time of order.
Cleveland Range United States : STEAM JACKETED KETTLE, MODEL KET-T (3,6,1... http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0166&article=ket... Page 1 of 4 5/13/2008 Catalog Home / Cooking equipment > Steam jacketed kettles > Table top models > Electric > STEAM JACKETED KETTLE, MODEL KET-T (3,6,12 GALLONS) ELECTRIC TILTING KETTLE STEAM JACKETED KETTLE, MODEL KET-T (3,6,12 GALLONS) ELECTRIC TILTING KETTLE TILTING STEAM JACKETED KETTLE "SPLASH PROOF SERIES", 2/3 STEAM JACKETED, 3, 6 or 12 GALLONS (11, 23 or 45 LITERS) CLEVELAND, electric kettle, Table Type, self-contained, tilting. 2/3 steam jacketed, type 304 Stainless Steel kettle and supports. Jacket rated at 50 psi with Safety Valve, Permanently filled Steam Jacket, Splash Proof Solid State Temperature (±1 C) and Safety Control System in plug-in Module including L.E.D. indicators. Marine Lock. Optional Lift Off Cover. Product Features Model KET-12-T shown Manual Tilting Balanced design Self-Contained Easily installed - needs only an electrical hook-up Steam Jacket Steam jacket filled with treated water, venting and/or refilling is not required Controls Accurate, consistant solid state temperature controls (mechanical thermostate not as accurate) - less than ±1 C variance (ideal for simmering). Operating temperature range from 145-260 F (63 C - 127 C) Water Resistant Controls Splash-proof construction Control panel includes: LED indicator for heat cycle, LED indicator for low water Power ON/OFF switch, Adjustable temperature control dial
Cleveland Range United States : STEAM JACKETED KETTLE, MODEL KET-T (3,6,1... http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0166&article=ket... Page 2 of 4 5/13/2008 Pouring Lip Large pouring lip for high capacity and chunky products. Rolled Rim Re-inforced rolled rim design prevents damage to kettle rim, eliminates "bar rim designs" Heating Elements Welded-in heating elements, (holds vacuum better, won't leak or loose water) Easily Cleaned Kettle and all exterior surfaces are of type 304 stainless steel with an #4 finish Pressure Gauge Rear mounted easy access pressure gauge and pressure relief valve to prevent tampering. Color coded easy to read pressure gauge with "green" and "vent air zone" Jacket Rating 50 psi steam jacket rating for higher cooking temperatures Safety Valve 50 psi Water Level Control Solid state water level control (no sight glass gauge to break or leak) Element Cover Splash proof element cover with a double gasket seal Marine Lock Self locking marine type tilting mechanism prevents accidental spills. Balanced design makes it easy to tilt Standard voltage 208-240 volts, 60 Hz, 3 phase, 3 wire. Model KET-6 and KET-12 are field rewirable to single phase Technical Specifications STEAM JACKETED KETTLE, MODEL KET-T (3,6,12 GALLONS) ELECTRIC TILTING KETTLE TILTING STEAM JACKETED KETTLE "SPLASH PROOF SERIES", 2/3 STEAM JACKETED, 3, 6 or 12 GALLONS (11, 23 or 45 LITERS) Weight 180 lb (43.0920 kg) Primary Power Input Rating 208-240/60/3 Shipping Weights KET12T, 180 lbs. (82 kgs) KET6T, 160 lbs. (73 kgs) KET3T, 95 lbs. (43 kgs) Installation Requirements Electrical Connection (Cord & Plug by others) 1/2" NPT water Connection (for hot and cold water faucet when ordered) 6" Rear Operating Clearance Accessories Equipment Stand Stainless Steel equipment stand with drain drawer and splash shield (ST-28)
Cleveland Range United States : STEAM JACKETED KETTLE, MODEL KET-T (3,6,1... http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0166&article=ket... Page 3 of 4 5/13/2008 Faucet Hot and cold (DPK) or cold only (SPK) water faucet with swing spout. Requires mounting bracket (FBKT) 316 Kettle Liner 316 Stainless Steel kettle liner for high acid food products (316-G) Electrical High wattages (HW) and special voltages Cooking Baskets (BS) Food Strainers (FS) Measuring Strips (MS) Spray Hose (PRS-K) Lift Off Cover (CL) Kettle Markings (KM) Downloads Brochure or Sell Sheet File Size Date Electric Kettles 236.2 KB Oct 25, 2005 CAD Symbols (KCL Cutsheets) File Size Date AutoCad Drawings Oct 24, 2005 Menu or Recipe Guide File Size Date Kettle Cookbook 138.3 KB Aug 16, 2005 Owner/Instruction Manual File Size Date Installation, Operation and Service Manual 2.4 MB Aug 16, 2005 Specification Sheet File Size Date ELECTRIC KETTLES, TABLE TYPE 134.0 KB Oct 22, 2007 ST28 Equipment Stand with Sliding Drain Drawer 162.9 KB Oct 28, 2005 Service Documentation STEAM JACKETED KETTLE, MODEL KET-T (3,6,12 GALLONS) ELECTRIC TILTING KETTLE - Service Documentation
Cleveland Range United States : STEAM JACKETED KETTLE, MODEL KET-T (3,6,1... http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0166&article=ket... Page 4 of 4 5/13/2008 Please Note: You may require Adobe Acrobat Reader to view these documents.
Cleveland Range United States : GAS KETTLES, KGT-T, (6, 12 Gallons) http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0167&article=ket... Page 1 of 3 5/13/2008 Catalog Home / Cooking equipment > Steam jacketed kettles > Table top models > Gas > GAS KETTLES, KGT-T, (6, 12 Gallons) GAS KETTLES, KGT-T, (6, 12 Gallons) TILTING, 2/3 STEAM JACKETED, "SPLASH PROOF SERIES", 6 or 12 GALLONS (23 or 45 LITERS) CLEVELAND, gas kettle, Table Type, self-contained, tilting, natural or LP gas, 2/3 steam jacketed, type 304 Stainless Steel and supports. Jacket rated at 50 psi with Safety Valve. Complete with solid state water level, temperature, and safety low water power cut off, including LED indicators. Option lift off cover. Product Features Model KGT-12-T (available in 6 or 12 gallons) Self contained Gas tilting kettle is easily installed, only needs a gas connection and a 115 volt outlet. Temperature Control Precise, consistent temperature control, less than 1 C temperature variance (ideal for simmering). Operating temperature range from 145-260 F (63 C- 127 C). Splash Proof "Splash Proof" solid state control panel for temperature, low water safety, and power "on/off" switch. Accurate L.E.D. indicators for heat cycle and low water warning. Construction Kettle and all exterior surfaces are a 304 Stainless Steel with a #4 finish. Efficiency Energy efficient (65%), high performance gas-fired heating system for fast heat up and recovery time: Six gallon model with a 34,000 BTU firing rate, and 22,100 BTU directly applied to the product.
Cleveland Range United States : GAS KETTLES, KGT-T, (6, 12 Gallons) http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0167&article=ket... Page 2 of 3 5/13/2008 Twelve gallon model with a 53,000 BTU firing rate, and 34,450 BTU directly applied to the product. Pressure Regulator Supplied with Gas Pressure Regulator. Gas Standard for natural gas operation Marine Lock Self locking marine type tilting mechanism prevents accidental tilting. Balanced design makes it easy to tilt. The tilt handle easily mounts on left or right side. Double safety gas shut off turns off the gas when the unit is tilted. Pouring Lip Large pouring lip for easier, faster pouring. Heavy duty Rolled Rim design provides strong reinforcement, prevents damages from abuse. Pressure Gauge "Splash Proof" recessed pressure/vacuum gauge. Steam Jacket Steam jacket permanently filled with treated distilled water, venting and / or refilling is not required. Jacket Rating 50 PSI Steam Jacket Rating. Safety valve mounted toward rear of kettle to avoid tampering. Spark Ignition Automatic Electronic Spark Ignition System. Electrical Connection Supplied with cord and plug for 115 volt controls. Technical Specifications GAS KETTLES, KGT-T, (6, 12 Gallons) TILTING, 2/3 STEAM JACKETED, "SPLASH PROOF SERIES", 6 or 12 GALLONS (23 or 45 LITERS) Power Input Type Gas Primary Power Input Rating 115-120/60/1 Power Output 34000 BTUs Installation Requirements 3/4" NPT Gas Connection 120volt, 1 phase electric (cord and plug provided) 1/2" dia. hot and cold water connection (for faucet when ordered) 4" Rear Operating Clearance Accessories Stand Stainless Steel equipment stand with sliding drain drawer and splash shield (ST-28) Faucet Hot and cold water faucet (DPK), or Cold Water (SPK). Requires bracket (FBKT) 316 Stainless Steel Liner (316G)
Cleveland Range United States : GAS KETTLES, KGT-T, (6, 12 Gallons) http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0167&article=ket... Page 3 of 3 5/13/2008 Gas Propane Gas Operation (PG) Cooking Baskets (BS) Food Strainers (FS) Measuring Strips (MS) Spray Hose (PRS-K) Lift Off Cover (CL) Kettle Markings (KM) Downloads CAD Symbols (KCL Cutsheets) File Size Date AutoCAD Library Aug 16, 2005 Menu or Recipe Guide File Size Date Kettle Cookbook 138.3 KB Aug 16, 2005 Owner/Instruction Manual File Size Date Operations, Maintenance, Service Manual 865.4 KB Aug 16, 2005 Specification Sheet File Size Date GAS KETTLES, TABLE TYPE, 6-12 GALLONS 112.0 KB Oct 22, 2007 Service Documentation GAS KETTLES, KGT-T, (6, 12 Gallons) - Service Documentation Please Note: You may require Adobe Acrobat Reader to view these documents.
Cleveland Range United States : ST28 Equipment Stand for Kettles and Braising Pans http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0167&article=st2... Page 1 of 3 5/13/2008 Catalog Home / Cooking equipment > Steam jacketed kettles > Table top models > Gas > ST28 Equipment Stand for Kettles and Braising Pans ST28 Equipment Stand for Kettles and Braising Pans Equipment Stand with Sliding Drain Drawer (Shown with Optional Folding Splash Guard for heavy pouring)
Cleveland Range United States : ST28 Equipment Stand for Kettles and Braising Pans http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0167&article=st2... Page 2 of 3 5/13/2008 ST28 Equipment Stand. For Counter top kettles and braising pans (skillets). Shown with Product Features All Stainless Steel Construction with 1-1/4" Square Tubing AJustable Feet (Rear Flanged for bolting to floor) Sliding Drain Drawer with Splash Screen Can be hard piped to floor drain. Improves santitation Ideal for mounting electric and gas counter top kettles and electric counter top skillets For Model KET3T, KET6T, KET12T, KGT6T, KGT12T, SET10, SET15. Can moun direct steam wit adapter Technical Specifications ST28 Equipment Stand for Kettles and Braising Pans Equipment Stand with Sliding Drain Drawer (Shown with Optional Folding Splash Guard for heavy pouring) Width x Depth x Height Weight 28 1/8" x 21 3/8" x 17 5/8" (71.44 cm x 54.29 cm x 44.77 cm) 40 lb (18.1440 kg) Installation Requirements Drain Connection Accessories Folding Splash Guard for Heavier Pouring Downloads Specification Sheet File Size Date ST28 Equipment Stand, for counter top kettles and braising pans (Skillets) 168.5 KB Oct 20, 2007
Cleveland Range United States : ST28 Equipment Stand for Kettles and Braising Pans http://www.clevelandrange.com/nafemproducts.asp?poc=cle&category=0167&article=st2... Page 3 of 3 5/13/2008 Please Note: You may require Adobe Acrobat Reader to view these documents.
Item# Job METRO MOBILE END- AND SIDE-LOAD WIRE BUN PAN RACKS Cost Effective: Metro s Bun Pan Racks offer an economical solution for sturdy, dependable storage and transport of bun pans. Two Styles Available: End-load models allow for optimum floor space utilization, while side-load models offer a larger tray landing area. Both styles can be loaded on one side and unloaded from the other for maximum efficiency and convenience. Choice of Slide Spacing: Each style is available with a choice of slide spacings 1 1 /2" (38mm), which has a 38 pan capacity, and 3" (76mm), which has a 20 pan capacity. UPS Shippable in one box for lower freight costs. Quick, Secure Assembly: Units assemble quick and easy without special tools. Lightweight, Maneuverable: 5" (127mm) swivel casters promote ease of mobility. Super Erecta Brite Finish End- and Side-Load Wire Bun Pan Racks InterMetro Industries Corporation North Washington Street Wilkes-Barre, PA 18705 www.metro.com Copyright 1999 InterMetro Industries Corporation 13.42
13.42 Job METRO MOBILE END- AND SIDE-LOAD WIRE BUN PAN RACKS SPECIFICATIONS: Slides, Frame, Posts: Super Erecta Brite finish with Metrolac protective coating. Casters: 5" (127mm) stem/swivel casters with resilient tread. End- and Side-Load Wire Bun Pan Racks DIMENSIONS: Approx. Height Width Length Slide Spacing Pan Capacity Pkd. Wt. Model No. Description (in.) (mm) (in.) (mm) (in.) (mm) (in.) (mm) No. Size (in.) (lbs.) (kg) RE1 End-Load 69 1750 21 3 /4 550 27 685 1 1 /2 40 38 18x26 61 28 RE3 End-Load 69 1750 21 3 /4 550 27 685 3 75 20 18x26 70 32 RS1 Side-Load 69 1750 19 1 /2 490 30 760 1 1 /2 40 38 18x26 61 28 RS3 Side-Load 69 1750 19 1 /2 490 30 760 3 75 20 18x26 70 32 ACCESSORIES: Model No. 9992DB 9992N 3 1 /2" (90mm) Diameter Rubber Donut Bumper 5 1 /2" (140mm) Diameter Rubber Donut Bumper Manufactured by: InterMetro Industries Corp. Phone 570-825-2741 North Washington Street FAX 570-825-2852 Wilkes-Barre, PA 18705 For Product Information, call 1-800-433-2232 www.metro.com For Customer Service, call 1-800-992-1776 InterMetro Industries Corporation North Washington Street Wilkes-Barre, PA 18705 www.metro.com L02-074 5/99 BJ Printed in U.S.A. Information and specifications are subject to change without notice. Please confirm at time of order.
Item No. Open Sides Models BC331KD KD Service Cart Specifier Identification No. Model No. Quantity Features & Benefits This economical service cart is sturdy and durable and is designed to handle a wide variety of transporting needs from the back of the dock to the front of the house. Use it for table set up, bussing service, delivering prepared foods to the food bar, coffee service, or transporting catering supplies off the delivery truck. It ships knocked down (KD) to minimize shipping costs, yet is easy to assemble and ready to use in minutes. Load capacity is 300 lbs. (136 kg). Three polypropylene shelves are lightly textured to reduce sliding. They are durable, stain resistant and easy to clean. Raised marine rails around each shelf prevent items from slipping off. Generous 11 3 4 (30 cm) open spacing between shelves speeds up loading and unloading. Aluminum uprights between shelves ensure optimum sturdiness and stability and are rust-resistant. Two ergonomic polypropylene handles and a set of plugs are included with each cart. Cart can be set up with one or both. Use plugs to fill top holes on other side when installing only one handle. Four non-marking 4 (10 cm) swivel casters without brake are durable and strong and offer quiet, easy transportation. Made of powder coated steel for extra strength and rustresistance. Optional accessories include a removable 8 gallon (30,3L) Trash Container and 2.5 gallon (9,5L) Silverware Holder. Available in Black (110) only. Easy to assemble. Directions included with each cart. Use plastic mallet only. Available in two colors, Speckled Gray (480) and Black (110). BC331KD Shown with One Handle, Silverware Holder and Trash Container (Plugs are used in place of other handle) BC331KD 2.5 Gallon (9,5 L) Silverware Holder 8 Gallon (30,3 L) Trash Container 2003 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056-U.S.A. Telephone (1)714 848 1555 Toll Free 800 854 7631 Customer Service Hot Line 800 833 3003 LIT FCSF-0203-38A 38A
Open Sides Models BC331KD KD Service Cart Item No. Specifier Identification No. Model No. Quantity 32-3/4" (83 cm) 16-1/4" (41 cm) 38" (96,5 cm) BC331KD Width Specifications Dimension Tolerance: +/- 1 /4" (0,64 cm) Load Inside Shelf Dimensions Exterior Dimensions Case lbs./cube Code Description Capacity L x D x H* L x D x H (with both handles) Kg/m 3 BC331KD Service Cart - Open Sides 300 lbs. 24 5 16" x 15 3 4" x 11 3 4" 32 7 8" x 16 1 4" x 38" 25.30 (4.70) (136 Kg.) (62 x 40 x 30 cm) (83,5 x 41 x 96,5 cm) 11,48 (0,133) *Height is between shelves. Optional Accessories 8 Gal. (30,3 L) Trash Container BC331KDTC 2.5 Gal. (9,5 L) Silverware Holder BC33KDSH Standard Cart Colors Speckle Gray (480) Black (110) Architect Specs The KD Service Cart shall be Cambro Model BC331KD. It shall be constructed of polypropylene shelves and anodized aluminum shelf supports. It shall have two each polypropylene ergonomic handles and two each polypropylene plugs. Each shelf shall have a slip-resistant, textured surface and raised edges on all four sides to prevent contents from sliding off. It shall have open sides with generous 11 3 4 (30 cm) spacing between shelves to speed up loading and unloading. It shall have four each 4 (10 cm) powder coated steel, swivel casters, all without brake. It shall be available with an optional 8 gallon (30,3 L) Trash Container and 2.5 gallon (9,5 L) Silverware Holder, both available in Black (110) only. It shall require assembly and shall be available in 2 colors. 2003 Cambro Manufacturing Company 5801 Skylab Road, Huntington Beach, California 92647-2056-U.S.A. Telephone (1)714 848 1555 Toll Free 800 854 7631 Customer Service Hot Line 800 833 3003 Printed in USA
Rubbermaid Commercial Products - Rubbermaid Material Handling : 3424-88 Utility Car... http://www.rcpworksmarter.com/rcp/products/detail.jsp?categoryid=3&subcategoryid=16... Page 1 of 2 5/13/2008 Material Handling > Utility & Service Carts 3424-88 Utility Cart with 4" dia (10.2 cm) Swivel Casters Versatile, durable carts perform a wide variety of tasks. Easy-to-clean smooth surfaces. Quiet casters and plastic construction help eliminate noise User-friendly easy to grip handles. Large 4" (10.2 cm) non-marking swivel casters. High style appearance with brushed aluminum uprights. 200 LB weight load. AVAILABLE COLORS Color Product UPC UCC Code RED 086876164718 00086876164718 PLAT 086876159493 00086876159493 OWHT 086876159516 00086876140033 BLA 086876159509 00086876159509 Red RED Platinum PLAT SPECIFICATIONS U.S. Metric Length: 33 5/8 in 85.4 cm Width: 18 5/8 in 47.3 cm Height: 37 3/4 in 95.9 cm Mass Capacity [Nom]: 200 lb 90.7 kg Mass Capacity [Max]: 200 lb 90.7 kg Bottom Shelf Capacity: Shelf Capacity: 67 lb 30.4 kg Top Shelf Capacity: Carton Cube: 4.66 ft3 0.13 m3 Ship Weight/Carton: 30 lb 13.61 kg Off White OWHT Black BLA Pack Quantity: 1 Cartons Per Pallet: 12 ADDITIONAL INFORMATION: Instructions: RCP_IS342488.pdf Product Sell Sheets: RCP_FS592_Utility_Cart.pdf, RCP_FS587_Refuse_Utility_Bins.pdf, RCP_FS563_Utility_Cart.pdf, RCP_FS644_SmartKitchen.pdf Chemical Resistance Guide: chem.pdf Service Carts Item # Description Length Width Height Mass Capacity Certification Material Process 3355-88 Utility Cart with Enclosed End Panels 31 in 18 in 37 1/2 in 300 lb Assembly PP
Rubbermaid Commercial Products - Rubbermaid Material Handling : 3424-88 Utility Car... http://www.rcpworksmarter.com/rcp/products/detail.jsp?categoryid=3&subcategoryid=16... Page 2 of 2 5/13/2008 3421 Utility Cart with 3" dia (7.6 cm) Swivel Casters and End Panels 33 5/8 in 18 5/8 in 3424-88 Utility Cart with 4" dia (10.2 cm) Swivel Casters 33 5/8 in 18 5/8 in 3457 Utility Cart with Lockable Doors, Sliding Drawer and 4" dia (10.2 cm) Swivel Casters 33 5/8 in 18 5/8 in 9T65-71 Utility Cart with 3" dia (7.6 cm) Swivel Casters 31 1/2 in 16 1/4 in 36 5/8 in 150 lb Assembly 37 3/4 200 lb Assembly in 37 3/4 200 lb Assembly in 36 in 100 lb Assembly Accessories for 3424-88: No. Description Process Volume Capacity Material Width Height Length Mass Capacity 3459 Utility Sliding Drawer with Lock 3353-88 Refuse Bin 8 gal 17 in 22 in 12 in 3354-88 Utility Bin 4 gal 17 in 10 1/2 in 12 1/8 in Consumables/Replacement Parts for 3424-88 No. Fits Description 3421-L1 3421, 3424-88, 3457 Top Shelf (Specify Color) 3421-L2 3421, 3424-88, 3457 Middle Shelf (Specify Color) 3421-L3 3421, 3424-88, 3457 Bottom Shelf (Specify Color) 3421-L4 3421, 3424-88, 3457 Handle Kit (2 Handles) (Specify Color) 3424-L6 3424-88, 3457, 3355-88 4" dia. (10.2 cm) Swivel Caster 3424-M2 3424-88 Aluminum Upright Kit (8 Uprights) Rubbermaid Commercial Products, LLC 3124 Valley Avenue, Winchester, VA 22601 www.rcpworksmarter.com
Project Name Item # PT-200 Gas Booster Heater For use with all conveyor and flight type dish machines (consult factory for AW Models) STANDARD FEATURES Specifications: The gas booster water heater to supply the final 180 F (82 C) rinse for the dishwasher will be a PrecisionTemp Model PT-200 as manufactured by PrecisionTemp, Inc., Cincinnati, OH 45237 U.S.A. The booster will have the capacity to heat 274 gph (1042 lph) from 115 F to 180 F (43 C to 82 C) or 480 gph (1824 lph) from 140 F (60 C) and it will be rated at 199,000 BTU, fired by gas and operated by 115 volts, single phase. The booster will be equipped with the VariFlame temperature control system, and requires no accumulator tank or circulating pump. The heater will be equipped with a microprocessor control system and an electronic on-board self diagnostic system. Serviceable components will be front accessible and electronic boards will be in a slide out drawer. The heater will be complete with all internal plumbing, including ¾ (2 cm) NPT pipe fittings from inlet and outlet. All controls will be built-in, and carry safety approval in accordance with ANSI 21.10.3. Sanitary approval will be in accordance with NSF Standard 5. A proper surface mounting circuit breaker or fused disconnect switch will be provided by the electrical contractor. The gas fired heating system will be controlled by quick reacting temperature sensor in the heat exchanger. The booster heater will be protected with an electronic temperature sensor and a high temperature limit switch (ECO). The heater will consist of an all stainless steel cabinet with 6 (15 cm) legs. The heater will include a pressure relief valve on outlet, a check valve on the inlet, and a high temperature limit switch. Fits under standard size dish table (see options) ETL Certified for gas, electrical, and sanitation Flow through design - no tank or pump Built in digital temperature readout Constant 180 F outlet with minimum 115 F incoming All stainless steel cabinet Front panel accessibility for all components No standing pilot - direct spark ignition to main burner Insulated microprocessor controlled burner Full gas modulation On board self-diagnostics Modular construction Factory authorized start-up included Standard Options 3 rear flue or 4 right side flue ( Must Choose) Propane or Natural Gas ( Must Choose) High altitude orifices (for use above 5,000 ft.) OPTIONALS ACCESSORIES Aluminum wall brackets Stainless steel 6 adjustable legs Stainless steel seismic legs Recirculation system** **NSF requires that if the booster is to be located more than 5 feet away from the dish machine, it must be installed with a recirculation system 11 Sunnybrook Drive, Cincinnati, OH 45237 Tel: 800-934-9690 Fax: 513-641-0733 www.precisiontemp.com
PT-200 Gas Booster Heater Temperature Rise 30 F / 15 C 40 F / 22 C 50 F / 28 C 60 F / 33 C 70 F / 38 C Gallons per Hour 640 480 384 320 274 Liters per hour 2422.66 1817 1453.60 1211.33 1037.2 To properly specify a PT-200, find the rinse flow in gallons per hour at 20 psi from the dishwasher manufacturers specification sheet. Find the corresponding gph flow that the PT-200 will provide and find the minimum inlet water temperature. For example, a flight type dish machine requires 320 gph of 180 F rinse water at 20 psi. In this case the inlet water temperature to the booster heater can be as low as 120 F. 30-3/4" 780.8mm 20-7/8" 530.4mm 31-5/16" 795.3mm 26-3/4" 679.4mm 19-13/16" 503.2mm 25-5/16" 642.9mm 8-3/8" 212.4mm 16-0" 406.4mm 5-3/4" 145.4mm 15-1/4" 387.0mm 6-0" 152.4mm Min Space Req'd 1-11/16" 42.5mm 5-9/16" 141.2mm 2-1/8" 53.9mm 2-11/16" 68.2mm 15-1/4" 387.0mm 6-0" 152.4mm Leg Hgt Right Side View Rear Side View Left Side View D#: DS0005 (02/07) (Rev. A) Natural Gas Pressure at Inlet in WC Propane (LPG) Pressure at Inlet in WC Manifold Pressure in WC Clearances Gas Connection Water Connections Electrical Connection Min Max Max Min Nat LP Sides Top Rear 7.0 10.5 11.0 14.0 2.85 10.0 6" Zero 6" ¾" NPT ¾" NPT 115v AC 15 amp Junction Box Warranty: see Manufacturer s Limited Parts and Labor Warranty for complete details. Available upon on request or download from www.precisiontemp.com Specifications subject to change without notice. 11 Sunnybrook Drive, Cincinnati, OH 45237 Tel: 800-934-9690 Fax: 513-641-0733 www.precisiontemp.com
4 3 2 1 1 2 3 4 5 6 7 8 9 10 11 D 30-3/4" 780.8 mm D 31-1/2" 800.0mm 7-1/2" 190.5 mm C 26-7/8" 682.8 mm 26-3/4" 679.5 mm 19-13/16" 503.2 mm 27-5/8" 702.6 mm C 19-3/4" 501.7 mm 8-3/8" 212.4 mm 6-0" 152.4 mm 16-0" 406.4 mm 13-1/4" 336.6 mm B 5-3/4" 145.4 mm 11-5/8" 296.1 mm 15-0" 381.9 mm Right Side View 1-11/16" 42.5 mm 5-9/16" 141.2 mm Rear Side View 2-11/16" 68.2 mm 2-1/8" 53.9 mm 7-1/2" 190.5 mm 15-0" 381.9 mm Left Side View 5-3/4" 147.0 mm B A 4 LEGEND 1 Side Flue Connection 4" (Optional) 2 T-mid Access (Recirc ONLY) 3 Gas Pipe Inlet 3/4" NPT (male) 4 Rear Flue Connection 3" (Shown) 5 Legs 6" Stainless Steel (Adj. to 7-1/2") 6 Combustion Air Louvres 7 SJO Power Wire 115Vac 15Amp 8 Water Outlet 3/4" NPT (female) 9 Water Inlet 3/4" NPT (female) 10 Access Panel / Digital Temp Read-out ** Digital Read-out on "FT" and "OR" models ONLY 11 Power Switch w/ Splash Guard 3 Notes: 1. If the booster heater is more than 5 feet from the dishwasher, the "PT-200RC" (recirculating) required. 2. It is suggested that the flue be routed to the condensate hood or pant leg duct above the dishwasher. 3. It is suggested that the electrical power to the booster be interlocked with the power to the condensate hood or pant leg duct exhaust fan. When direct vented, power and gas will remain on at all times. 4. Clearances: Minimum of 6" inches for all sides. Full access to the front panel. This Document is Property Containing Proprietary Information Which Must Not Be Reproduced or Disclosed Without Written Permission and Must Be Returned Upon Demand. Revisions: 2 DRAWN BY: Chuck Haas CHECKED BY: APPROVED BY: DATE: DATE: DATE: TOLERANCES - Except as Noted MACHINED 125 ANGULAR SURFACES DECIMAL X.X = DECIMAL X.XX = DECIMAL X.XXX = INCHES ` 0.030 ` 0.010 ` 0.005 THREAD LENGTH DIMENSIONS ARE FULL THREAD HOLES TO BE CHAMFERED ONE THREAD DEPTH MAX UNLESS OTHERWISE SPECIFIED DECIMAL DECIMAL DECIMAL 27Feb07 ` 1/2 DEGREE MILLIMETERS X, = ` 0,76 X,X = ` 0,25 SIZE: X,XX = ` 0,13 BREAK OR DEBURR ALL SHARP EDGES (0.015" MAX) UNLESS OTHERWISE SPECIFIED 11 Sunnybrook Drive, Cincinnati, Ohio 45237 TITLE: PT-200 Gas Booster Heater Customer Reference Drawing C SCALE: SHEET 1 OF 1 N / A DWG NO : DS0006 1 A
Job Item No PowerMax200 TM Gas Booster Heater ` Model: PM200N TM or PM200L TM Temperature Rise 40 0 Rise 50 0 Rise 60 0 Rise 70 0 Rise 140 0 Rise Gallons per Minute 8.7 7.0 5.5 5.0 2.5 Gallons per Hour 520 420 330 300 150 FEATURES AND BENEFITS Single point water, gas and electrical connections Factory-provided pressure and temperature relief valve Space saving design installs below dishtables Can be installed in a remote location up to 150 feet from the scullery All waterways constructed of stainless steel, copper and brass for corrosion protection and clean operation Simple, easy maintenance through front panel All stainless steel cabinet and frame Instant 185 0 F water provided consistently to dishwasher rinse cycle Welded stainless steel accumulator (limited lifetime warranty) maintains rinse water at 185 0 F Woven Ceramic Fiber Infrared Power Burner Radial solid copper fin-tube heat exchanger for 360 0 heat transfer Burners activated by water flow & temperature Advanced microprocessor controls Natural Gas or Liquid Propane 199,990 BTUH Can provide 100% of hot water requirement for many restaurants ACCESSORIES AND OPTIONS (available at extra cost) EZ-Vent Kit for Venting through dishwasher ventilation system Factory Authorized StartUp-(highly recommended) Re-circulating kit ¾;1 for remote installations and/or single tank hot water coil tank heat (also requires a CT-1 module) 1-¼ for long distance remote installations and/or 2 tank hot water coil tank heat and/or 2 dishwasher rinse service (also requires CT-2 module) Wall Mount Kit Water Hammer Arrester Water Pressure Gauge Water Pressure/Temperature Gauge Water pressure reducing valve (if water supply pressure exceeds 80psi) Low Pressure water pressure reducing valve (for dishwasher rinse) Auxiliary PowerVent required for extended flue lengths. Call factory EZ Install Kit Seismic Legs Printed in USA R6/05