GOLD AIR HANDLING SYSTEM OVERVIEW

GOLD AIR HANDLING SYSTEM OVERVIEW

Four unbeatable reasons why you should choose GOLD units. GOLD PX Plate heat exchanger GOLD RX Rotary heat exchanger GOLD CX Coil heat exchanger GOLD SD Supply air and extract air handling units Saves space The GOLD has compact dimensions and furthermore it is possible to connect sharp duct bends directly to the air handling unit without pressure losses. This saves you space in the plant room. Optimal operating economy Energy-saving fans, efficient heat recovery and full control of temperatures, airflows and operating times offer optimal operational economy. Economical control functions A large number of functions integrated into the control system are ready to be activated via a hand-held micro terminal. Several of the functions provide unique opportunities for saving energy. Plug and Play Ready-to-use control functions are provided for accessories such as cooling units and heating coils and wiring is done by means of cables with quick connector. Plug and Play! New Products, 2007 In 2005, we introduced plate-type and coil-type heat exchangers for the GOLD units. During 2006, we presented the GOLD SD supply air and extract air handling units. Here are the new products for 2007: ReCO 2 Energy-saving function and accessories for recirculating extract air with guaranteed air quality. The function is patentpending. See page 20. Xzone Function and accessories for controlling two temperature zones. Preheating Function and accessories for preheating outdoor air. Prefilter Function and accessories for prefiltering outdoor air and/or extract air. The new ReCO 2 function can be used for saving energy in an air handling unit equipped with the air recirculation section accessory. 2 Registered design. The company reserves the right to make design changes without prior notice.

Energy efficiency brought into focus. Optimized heat recovery and cooling energy recovery Swegon s rotary heat exchangers (RX) offer unbeatable temperature efficiency, up to 85% and low pressure drop. The rotary heat exchanger recovers cooling energy just as efficiently, especially if you select one with hygroscopically coated rotor surfaces. However, in some applications, the airflow paths through the heat exchanger must be completely separate from one another. Such applications call for the use of a plate heat exchanger (GOLD PX) or coil heat exchangers (GOLD CX and GOLD SD). These alternative heat exchangers have an energy-efficient, anti-frost protection system that also measures humidity in the extract air. This ensures that the efficiency will not be controlled to the min. setpoint until the actual risk of freezing is imminent. Swegon s heat exchangers cut your costs of operating the heating and cooling system of the building to optimally low levels. Energy-efficient fans The motor and frequency inverter of the fans in the GOLD units are optimized to generate the best output while consuming as little power as possible. The motors perform to Class EFF1, i.e. their performance measures up to the highest efficiency rating classified by the EU and CEMEP European Committee of Manufacturers of Electrical Machines and Power Electronics. The frequency inverters also have a high power factor. This enables the electrical installation of fuses with lower rating. The fans are compact and take up little space. Sharp bends can be connected directly against the fan outlet without pressure losses. Low noise level enables the use of smaller sound absorbers in some applications the ventilation system can be selected completely without them. Swegon s fans offer low energy consumption, low installation costs, low pressure losses and space saved. Registered design. The company reserves the right to make design changes without prior notice. 3

Tools worth their weight in gold. An intelligent economist Pressures, airflows, temperatures, energy recovery and operating periods can be controlled in the IQnomic control system, which is standard in all the GOLD air handling units. Practically all the functions you can think of for an air handling unit are incorporated into the system and they are all ready to be activated. There are also several unique energy-saving functions such as Cooling Boost, density-corrected airflow and season-related airflow. All the settings and readings can be entered/viewed in plain text via a user-friendly, hand-held micro terminal. As standard, the GOLD has support for all the usual communication standards (TCP/IP, EIA 485 and EIA 232). The TBLZ communication unit can also be used for communication via LON and Trend. The GOLD also has a built-in web communication function ready to be connected to the network. All you need is an ordinary computer connected to the network. The fact that the control equipment is integrated into and specifically developed for the GOLD ensures that its electronics and mechanics operate hand in hand. This also offers you the chance to come a step further than you would with a control system built up of standard components. The IQnomic involves substantially lower costs compared with the planning, procuring, programming, configuring and installation of conventional control components and supervisory systems. ProUnit makes it easy to choose the right unit ProUnit helps you select the right air handling unit. You can access this fully web-based software from Swegon s website. In ProUnit, you can procure project-specific flow diagrams, compare heat exchanger options, estimate energy costs, life cycle costs, procure a contractor demarcation list and see how you will be benefited by using specific control functions. By linking to AutoCAD and MagiCAD, models can be exported for use in the design work. ProUnit makes it an easy task to select the right GOLD unit for an optimal and energy-efficient indoor climate. 4 Registered design. The company reserves the right to make design changes without prior notice.

Effective solutions with the GOLD. Decentralized ventilation Swegon has a history of creating pioneering products and the GOLD is generally used as a criterion by both clients and competitors. Swegon has also taken a step further and developed solutions aimed at giving the client maximal return on investment. Decentralised ventilation is one example. The concept involves using several smaller air handling units, instead of one single large unit. Each unit serves its own smaller section of the building and this offers the client increased profitability. A decentralized solution namely sets more floor surface free that can generate additional income from leases. This is possible in that the GOLD unit takes up little space and the level of sound it generates is low. The operating costs are in many cases also lower because the fans, heat recovery and controls in smaller air handling units are more efficient than those of a larger unit. One single large ventilation unit in the cellar, for instance, requires considerable floor surface and large shafts (upper illustration). With the GOLD system, it is possible to have one air handling unit on each floor of the building occupying the same space as the shaft. This leaves the whole cellar free for lettable floor surface for car parking spaces, for instance (lower illustration). Further benefits are that the building becomes more flexible, because it is easier to adapt the ventilation system to each tenant s specific comfort requirements and that the building can be completed by stages both in new-building and refurbishment schemes. Decentralized ventilation using GOLD units sets floor surface free for other uses and offers enhanced flexibility. Swegon offers package solutions for economic and demand-controlled ventilation system operation Swegon Solutions. Swegon Solutions Swegon Solutions provide you with complete package solutions for an invigorating indoor climate. Swegon can offer you optimized solutions for hotels, factories, office buildings, shopping centres and other public buildings. All the individual components in our various packages are specially selected for optimal compatibility. The core of Swegon Solutions is the GOLD air handling system. Depending on structural engineering considerations and activity inside the building, the GOLD unit can be combined with other products in Registered design. The company reserves the right to make design changes without prior notice. Swegon s range, such as Parasol comfort modules, Primo peripheral wall systems or air diffusers in the Ceiling Collection. The GOLD has ready-to-use control functions for the various solutions that provide economical operation and the highest degree of comfort. Swegon Solutions offer unique possibilities for economical and demand-controlled operation. 5

Here s how you in particular earn by the GOLD. The Architect The GOLD requires limited space for installation without having to compromise performance and quality. Thanks to its low noise level and attractive design, the GOLD can even be installed somewhere right inside the premises being air conditioned. Accessories well-suited to their purpose also make it possible to install GOLD units outdoors. Your work is made substantially easier by GOLD flexibility and your creativity is never restricted, rather the reverse! The Consultant The GOLD units are easy to place because they can be connected to ducting in a number of ways. No extensive work is required for describing how the control, regulating and supervisory system should be designed; all this is there, integrated into the GOLD. A description and flow charts can be obtained from the ProUnit air handling unit selection software. Correct technical data and knowledge that the units have been granted certification by Eurovent are additional guarantees that no unpleasant surprises will arise when the ventilation system is put into operation. You don t have to reinvent the wheel; you can instead focus on making good use of GOLD functionality and energy efficiency in the best possible way. The Installer The GOLD can be installed quickly and easily. In applications that require external functions such as dampers, presence detectors or a cooling unit, these can be easily wired to clearly marked terminal blocks. Certain wiring operations are done directly with modular connectors. Should the passageways through the site prove to be narrow; the larger air handling units can be easily split into sections. The GOLD is the ideal alternative for turnkey contract projects. All the necessary functions are built in; you need only activate those required, including communication and supervision. You are spared unpleasant surprises and you never need to face the risk that your tender won t make both ends meet! The Client/User The GOLD units offer hard-to-beat operating economy and life cycle costs (LCC) in a class of their own. Their flexibility is unparalleled and is of great benefit when ventilation prerequisites change, for rebuilding projects, etc. The GOLD can exchange information with most communication systems available on the market. In buildings that have a data network of their own, the GOLD can be connected to the network just as easily as it is to connect a printer, for instance. You will never notice that the air handling unit is working backstage. You ll be reminded of its presence only by its low operating and life cycle costs and that everyone who spends time or rents rooms in the building are satisfied, contented and willing to pay! 6 Registered design. The company reserves the right to make design changes without prior notice.

Technical description General General The GOLD RX/PX/CX one-piece units are complete air handling units with direct-driven supply air and extract air fans, supply air and extract air filters and heat exchanger. The heat exchanger is either of rotary type (RX), plate type (PX) or consists of two coils (CX). The GOLD SD single-direction units are supply air/extract air handling units with one direct-driven supply air or extract air fan. Optional filters are available for all sizes. Heat exchanger coils and unmounted pipework package can be selected for the size 14-80 units. The GOLD has built-in control equipment that can be operated from the hand-held micro terminal with clear-text display. The electrical and control system is completely integrated into the air handling unit. The microprocessor-based equipment controls and regulates temperatures, airflows and other functions. A large number of functions are built into the system and are simple to activate. If supplementary function sections such as dampers and air coolers are required, they must be installed in the ductwork. With provision for cooling and heating The GOLD is also well suited for cooling, preheating and postheating. The control functions in the control system are ready to activate and the relevant items of equipment are available as accessories. Range of application The GOLD units are designed for use in comfort ventilation applications. Depending on the variant selected, GOLD units can be utilised in buildings such as office buildings, schools, day nurseries, public buildings, shops, residential buildings, etc. GOLD units equipped with plate/coil heat exchanger (PX/CX) and separate supply air and extract air handling units (SD) can also be used for the ventilation of moderately humid buildings; however not where the humidity is continuously high, such as in indoor swimming baths. The separate GOLD supply air and extract air handling units (SD) are designed for applications in which the supply air and extract air flows need to be completely separated from one another or where, due to limited available space, separate units for supply air and extract air are needed. They can also be used individually if only one of the variants is needed. GOLD units can be installed outdoors and then must be equipped with with roof, air intake section and exhaust air hood accessories. Certification Swegon AB has a certificated Quality Management System that conforms to ISO 9001 and an Environmental Management System that conforms to ISO 14001 Standards. The GOLD Air Handling System is also certificated by Eurovent, No. AHU-06-06-319. GOLD RX GOLD PX GOLD CX GOLD SD Certificate No. 06.06.319 Registered design. The company reserves the right to make design changes without prior notice. 7

Overview Airflows GOLD RX, PX/CX, SD All the diagrams and performance data specified in this brochure are meant for use as an overview. Exact sizing can be carried out in the web-based ProUnit air handling unit selection software. Contact your nearest Swegon representative for a computer-generated estimate or use the software yourself. It is available at www.swegon.com Available total pressure rise, Pa m 3 /h m 3 /s GOLD Airflow, m 3 /s RX Min. 250 Pa Max. SFP v 2.5 04 0.08 0.42 0.45 05 0.08 0.42 0.60 08 0.10 0.72 0.90 14 0.20 1.10 1.10 20 0.20 1.50 1.80 25 0.30 2.10 2.20 30 0.30 2.40 3.00 35 0.60 2.90 3.10 40 0.60 3.40 4.10 50 0.80 4.30 4.60 60 0.80 5.00 6.00 70 1.00 6.00 6.30 80 1.00 6.90 8.20 m 3 /h GOLD Airflow, m 3 /s PX Min. 250 Pa Max. SFP v 2.5 Available total pressure rise, Pa m 3 /s 04 0.08 0.50 0.52 05 0.08 0.50 0.68 08 0.10 0.80 1.00 14 0.20 1.40 1.40 20 0.20 1.70 1.90 25 0.30 2.60 2.60 30 0.30 3.10 3.40 GOLD Airflow, m 3 /s CX Min. 250 Pa Max. SFP v 2.5 35 0.60 3.40 3.40 40 0.60 3.60 4.40 50 0.80 5.00 5.00 60 0.80 5.80 6.50 70 1.00 7.00 7.00 80 1.00 7.80 9.00 Available total pressure rise, Pa m 3 /h m 3 /s 1 The first value is applicable to fan+filter, one airflow; the second value for fan+filter+coil heat exchanger, two airflow directions. GOLD Airflow, m 3 /s SD Min. 250 Pa Max. SFP v 2.5 04 0.08 0.52 0.52 05 0.08 0.68 0.68 08 0.10 1.05 1.05 14 0.20 1.6/1.35 1 1.6/1.35 1 20 0.20 2.5/1.8 1 2.5/2.1 1 25 0.30 2.7/2.4 1 2.7/2.4 1 30 0.30 3.7/3.0 1 3.7/3.2 1 35 0.60 3.9/3.4 1 3.9/3.4 1 40 0.60 5.0/3.9 1 5.0/4.4 1 50 0.80 5.4/5.0 1 5.4/5.0 1 60 0.80 7.3/6.1 1 7.3/6.5 1 70 1.00 7.9/7.0 1 7.9/7.0 1 80 1.00 10.0/8.0 1 10.0/9.0 1 8 Registered design. The company reserves the right to make design changes without prior notice.

Installation, Dimensions and Weights GOLD RX, sizes 04/05, 08 Delivery and transport within the site The size 04/05 and 08 GOLD units are produced in one single variant. All components are arranged at their given physical location inside the air handling unit. The junction hood can be removed, if required, for transporting the unit within the building site. The air handling unit is supplied on a wooden pallet. Stand/Base If the air handling unit is installed horizontally, it must be mounted on a stand (accessory) or some other form of base support, so that its inspection doors can be opened. Installation/duct connection options A: The GOLD is supplied in a right-hand version. The unit can be changed to the left-hand version at the building site by making a simple adjustment in the control equipment. B: The air handling unit can be installed up ended. Right-hand version Left-hand version Outdoor air Supply air Extract air Exhaust air Size A B C D E F G H I L Ø Weight, kg 04/05 750 820 236 345 239 268 385 920 267 1500 315 260 08 800 990 273 440 276 293 500 1085 292 1600 400 315 Clear space for inspection A clear space of 800 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood. GOLD 04: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 05: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 16 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 08: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 20 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A Registered design. The company reserves the right to make design changes without prior notice. 9

Installation, Dimensions and Weights GOLD RX sizes 14/20, 25/30, 35/40 Delivery and transport within the site The GOLD 14/20, 25/30 and 35/40 are always supplied as one complete unit. The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electrical and control cables have quick connectors. The junction hood can be removed, if required, for transporting the unit within the building site. The air handling unit is delivered on wooden beams. Duct connection options A: The GOLD is supplied in a right-hand version. The unit can be changed to the left-hand version at the building site by making a simple adjustment in the control equipment. B: The arrangement of the functional sections can be vertically reversed. Specify this by selecting fan arrangement 1 or 2 when ordering! C: The fan outlet at the top of the air handling unit is covered by a cover panel. This cover panel can be easily moved to the end wall panel if it is desirable for the upper fan to discharge air upwards. The fan outlet can also be used for both forward and upward air discharge. D: Sizes 14-30; specify when ordering whether the unit shall have an air intake from above for outdoor air or extract air. * * Fan arrangement 1 Fan arrangement 2 Right-hand version * * Fan arrangement 1 Fan arrangement 2 Left-hand version * Sizes 14-30 Outdoor air Supply air Extract air Exhaust air 28 28 50 50 Size A B C D E F G H I J K L Weight, kg 14/20 765 1295 1036 550 196 400 1000 1295 252 122 146 2080 640 25/30 835 1595 1336 550 180 500 1200 1595 300 148 194 2220 840 35/40 875 1885 1626 550 125 600 1400 1885 300 192 242 2300 1100 Division at the building site A D A The unit can be divided into three sections at the building site. Dimensions: See A and D in the table above. Weight, size 14/20: A = 235 kg, D = 170 kg. Weight, size 25/30: A = 310 kg, D = 220 kg. Weight, size 35/40: A = 405 kg, D = 290 kg. Clear space for inspection A clear space of 900 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood. GOLD 14: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 20: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 25: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 30: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 20 A GOLD 35: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 40: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 32 A 10 Registered design. The company reserves the right to make design changes without prior notice.

Installation, Dimensions and Weights GOLD RX, sizes 50/60 and 70/80 Delivery and transport within the site The GOLD 50/60 is always supplied as one complete unit. The GOLD 70/80 is supplied as two units. The one unit consists of the centre section with heat exchanger and fan/filter section where the fan is located in the upper level. The other unit consists of a fan/filter section in which the fan is placed in the lower level. The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electrical and control cables have quick connectors. The unit is supplied on 100 m high support feet made of steel. Duct connection options A: Specify right-hand or left-hand version when ordering! B: The arrangement of the functional sections can be vertically reversed. Specify this by selecting fan arrangement 1 or 2 when ordering! C: The fan outlet at the top of the air handling unit is covered by a cover panel. This cover panel can be easily moved to the end wall panel if it is desirable for the upper fan to discharge air upwards. The fan outlet can also be used for both forward and upward air discharge. Fan arrangement 1 Fan arrangement 2 Right-hand version Fan arrangement 1 Fan arrangement 2 Left-hand version Outdoor air Supply air Extract air Exhaust air 34 Connection to Power Supply 28 28 76 Supplied on 100 mm high support feet. They can be removed or kept as they are when the unit is in place. The unit has provision for fitting the adjustable support feet. Size A B D E F G H I J K L Weight, kg 50/60 1050 2318 570 150 800 1600 2253 423 115 360 2670 1690 70/80 1250 2637 570 150 1000 1800 2640 319 161 419 3070 2379 76 Division at the building site A D A The unit can be divided into three sections at the building site. Dimensions: See A and D in the table above. Weight, size 50/60: A = 638 kg, D = 414 kg. Weight, size 70/80: A = 900 kg, D = 579 kg. Clear space for inspection A clear space of 900 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood. GOLD 50: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 25 A GOLD 60: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 40 A GOLD 70: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 32 A GOLD 60: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 50 A Registered design. The company reserves the right to make design changes without prior notice. 11

Installation, Dimensions and Weights GOLD PX, sizes 04/05, 08 Delivery and transport within the site The GOLD 04/05 and 08 are produced in one single variant. All of its components are arranged at their given physical location inside the air handling unit. The junction hood can be removed, if required, for transporting the unit within the building site. The air handling unit is supplied on a wooden pallet. Base frame/set of support legs The GOLD 04/05 and 08 are supplied on a base frame with integrated openings for the forks of a fork-lift truck. The set of support legs is available as an accessory. Duct connection options A: Specify right-hand or left-hand version when ordering! Right-hand version Left-hand version Outdoor air Supply air Extract air Exhaust air 180 80 28 28 28 50 32 50 80 Size A B C D E F G H I L Ø Weight, kg 04/05 800 820 236 345 239 268 385 920 267 2000 315 355 08 915 990 273 440 276 293 500 1085 292 2230 400 455 Clear space for inspection A clear space of 1,000 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood. GOLD 04: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 05: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 16 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 08: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 20 A or 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A 12 Registered design. The company reserves the right to make design changes without prior notice.

Installation, Dimensions and Weights GOLD PX, sizes 14/20 and 25/30 Delivery and transport within the site The GOLD 14/20 and 25/30 are always supplied as one complete unit. The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electrical and control cables have quick connectors. The air handling unit is delivered on wooden beams. The junction hood can be removed, if required, for transporting the unit within the building site. Duct connection options A: Specify right-hand or left-hand version when ordering! B: Specify when ordering whether the unit shall have an outdoor air intake from above and/or extract air discharge upward! Right-hand version Left-hand version Outdoor air Supply air Extract air Exhaust air M M 28 E E 28 50 50 80 D If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accessories) can be used for this purpose. Size A B C D E F G H I J K L Weight, kg 14/20 765 1295 1036 1200 400 400 1000 1295 252 122 146 2730 760 25/30 835 1595 1336 1500 550 500 1200 1595 300 148 194 3170 1020 Division at the building site A D A The unit can be divided into three sections at the building site. Dimensions: See A and D in the table above. Weight, size 14/20: A = 235 kg, D = 290 kg. Weight, size 25/30: A = 310 kg, D = 400 kg. Clear space for inspection A clear space of 900 mm must be provided in front of the unit and at least 200 mm must be provided above the junction hood. GOLD 14: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 20: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 25: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 30: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 20 A Registered design. The company reserves the right to make design changes without prior notice. 13

Installation, Dimensions and Weights GOLD CX, size 35/40 Delivery and transport within the site The size 35/40 GOLD units are always supplied as one complete unit. The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electrical and control cables have quick connectors. The air handling unit is delivered on wooden beams. The coil heat exchanger system is filled with liquid from the factory. Duct connection options A: Specify right-hand or left-hand version when ordering! B: The arrangement of the functional sections can be vertically reversed. Specify this by selecting fan arrangement 1 or 2 when ordering! C: The fan outlet at the top of the air handling unit is covered by a cover panel. This cover panel can be easily moved to the end wall panel if it is desirable for the upper fan to discharge air upwards. The fan outlet can also be used for both forward and upward air discharge. Fan arrangement 1 Fan arrangement 2 Right-hand version Fan arrangement 1 Fan arrangement 2 Left-hand version Outdoor air Supply air Extract air Exhaust air Connection to Power Supply 28 28 50 50 250 M If a water trap (accessory) is fitted, the air handling unit must be raised at least 50 mm to provide space for the water trap. Support feet (accessories) can be used for this purpose. Applicable to the right-hand version, fan arrangement 2 and the left-hand version, fan arrangement 1. Size A B C D E F G H I J K L M Weight, kg 35/40 875 1885 1626 680 125 600 1400 1885 300 192 242 2430 600 1450 Division at the building site The unit can be divided into three sections at the building site. Dimensions: See A and D in the table above. Weight, size 35/40: A = 400 kg, D = 650 kg. Clear space for inspection A clear space of 900 mm should be provided in front of the unit. GOLD 35: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 20 A GOLD 40: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 32 A A D A 14 Registered design. The company reserves the right to make design changes without prior notice.

Installation, Dimensions and Weights GOLD CX, sizes 50/60 and 70/80 Delivery and transport within the site The size 50/60 GOLD units are always supplied as one complete unit. The size 70/80 GOLD units are supplied as two units. The one unit consists of the centre section with heat exchanger and fan/ filter section where the fan is located in the upper level. The other unit consists of a fan/filter section in which the fan is placed in the lower level. The air handling unit can be split into three sections to facilitate transporting it within the building site. The three sections are joined together by bolts and the electrical and control cables have quick connectors. The unit is supplied on 100 m high support feet made of steel. The coil heat exchanger system is filled with liquid from the factory. Duct connection options A: Specify right-hand or left-hand version when ordering! B: The arrangement of the functional sections can be vertically reversed. Specify this by selecting fan arrangement 1 or 2 when ordering! C: The fan outlet at the top of the air handling unit is covered by a cover panel. This cover panel can be easily moved to the end wall panel if it is desirable for the upper fan to discharge air upwards. The fan outlet can also be used for both forward and upward air discharge. Fan arrangement 1 Fan arrangement 2 Right-hand version Fan arrangement 1 Fan arrangement 2 Left-hand version Outdoor air Supply air Extract air Exhaust air Connection to Power Supply 28 28 76 76 254 M Supplied on 100 mm high support feet. They can be removed or kept as they are when the unit is in place. If a water trap is fitted, in addition to the base beams, the air handling unit must be raised at least 50 mm to provide space for the water trap. It is advisable to let these support feet remain on the unit. Or you can remove them and fit adjustable feet (accessory). Size A B D E F G H I J K L M Weight, kg 50/60 1050 2318 760 150 800 1600 2253 423 115 360 2860 650 2237 70/80 1250 2637 760 150 1000 1800 2640 319 161 419 3260 800 3092 Division at the building site A D A The unit can be divided into three sections at the building site. Dimensions: See A and D in the table above. Weight, size 50/60: A = 638 kg, D = 961 kg. Weight, size 70/80: A = 900 kg, D = 1,292 kg. Clear space for inspection A clear space of 1,100 mm should be provided in front of the unit. GOLD 50: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 25 A GOLD 60: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 40 A GOLD 70: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 32 A GOLD 80: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 50 A Registered design. The company reserves the right to make design changes without prior notice. 15

Installation, Dimensions and Weights GOLD SD, sizes 04/05, 08 Delivery and transport within the site The size 04/05 and 08 GOLD SD units are produced in one single variant. All of its components are arranged at their given physical location inside the air handling unit. The air handling unit is supplied on a wooden pallet. The GOLD SD can be used as a supply air or an extract air handling unit. If both supply air and extract air handling units are used in a ventilation system, the supply air unit is fitted with a control unit and the extract air unit is without. A communication cable is used to connect them to one another making it possible to control both units. Filter holders are available for pleated filters. Set of filters with pleated medium, pressure sensor, hoses and communication cable are optional extras. Stand/Base If the air handling unit is installed horizontally, it must be mounted on a stand (accessory) or some other form of base support, so that its inspection doors can be opened. Duct connection/installation options The air handling unit can be upended or turned upside down. The unit can also be installed with the inspection door upward, but not downward. Direction of airflow 12 B E L 16 A C 16 F 12 D D H Ø Ø Size L B H A C D E F Ø Weight, kg 04 1100 820 490 948 152 245 236 410 315 115 05 1100 820 490 948 152 245 236 410 315 115 08 1175 990 575 1023 152 288 321 495 400 150 Clear space for inspection A clear space of 1,100 mm should be provided in front of the unit. GOLD 04: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A GOLD 05: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A GOLD 08: 1-phase, 3-wire, 230 V -10/+15%, 50 Hz, 10 A 16 Registered design. The company reserves the right to make design changes without prior notice.

Installation, Dimensions and Weights GOLD SD, sizes 14/20, 25/30, 35/40, 50/60, 70/80 Delivery and transport within the site The size 14/20, 25/30, 35/40 and 50/60 GOLD SD units are always supplied as one complete unit. The size 70/80 GOLD SD units are always supplied as one unit if they each consist of a fan or fan+filter. If the unit consists of a fan + filter + coil heat exchanger, it is supplied as two units. The one unit then consists of a fan + coil heat exchanger and the other unit consists of a filter. The air handling unit can be split at the building site to facilitate transporting it within the site. The sections are joined together by bolts and the electrical and control cables have quick connectors. The size 14-40 GOLD SD units are supplied on wooden beams and the size 50-80 units are supplied on 100 mm high support feet made of steel. The GOLD SD can be used as a supply air or an extract air handling unit. If both supply air and extract air handling units are used in a ventilation system, the supply air unit is fitted with a control unit and the extract air unit is without. A communication cable is used to connect them to one another making it possible to control both units. Duct connection options A: Specify right-hand or left-hand version when ordering! B: The fan outlet at the top of the air handling unit is covered by a cover panel. At the building site, this cover panel can be easily moved to the end wall panel if it is desirable for the upper fan to discharge air upwards. The fan outlet can also be used for both forward and upward air discharge. Left-hand version Outdoor air Fan Fan + Filter Fan + Filter + Coil heat exchanger in extract air Droplet eliminator is optional. Fan + Filter + Coil heat exchanger in supply air Supply air Extract air Exhaust air Right-hand version Direction of airflow I B G 12 21 21 L1 F 100 21 E L2 C E L3 D C J 21 F H J 45 A 100 28 28 Fan Fan + Filter Fan + Filter + Heat recovery coil Sizes 50/60 and 70/80 are supplied on 100 mm high support feet. They can be removed or kept as they are when the unit is in place. If a water trap is fitted, in addition to the base beams, the air handling unit must be raised at least 50 mm to provide space for the water trap. It is advisable to let these support feet remain on the unit. Or you can remove them and fit adjustable feet (accessory). Size L1 L2 L3 B H A C D E F G I J 14/20 1040 1909 2505 1295 756 1036 1012 619 919 400 1000 146 178 25/30 1145 2014 2610 1595 1026 1336 1117 619 919 500 1200 194 263 35/40 1145 2014 2610 1885 1026 1626 1117 619 919 600 1400 242 213 50/60 1145 2014 2610 2313 1320 2165* 1117 619 919 800 1600 355 260 70/80 1278 2500 3260 2637 1320 2484* 1250 760 1250 1000 1800 419 160 *) The size 50 80 GOLD units have transverse base beams supporting their ends. Clear space for inspection A clear space of 900 mm should be provided in front of the unit. GOLD 14-35: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 10 A GOLD 40-50: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 60: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 20 A GOLD 70: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 16 A GOLD 60: 3-phase, 5-wire, 400 V -10/+15%, 50 Hz, 25 A Registered design. The company reserves the right to make design changes without prior notice. 17 Size Weight,kg fan Weight, kg fan + filter Weight,kg fan + filter + coil 14/20 230 340 475 25/30 310 450 670 35/40 365 520 760 50/60 550 760 1170 70/80 675 945 1700

Complements and accessories Duct accessories TBSA Damper TBLA Air heater, postheating TBLF Air heater, preheating Hot water TBKA Air cooler ( water) TBKC Air cooler (direct expansion) Tightness Class 3 to EN 1751 Standard. Circular or rectangular connections that fit the relevant size of GOLD unit Complete with damper actuator for 230 V, (modulating, spring return or on/off). TBFA Prefilter Several capacity variants Circular or rectangular connections that fit the relevant size of GOLD unit Incorporated into its own insulated casing for the size 50/60 and 70/80 GOLD units. Available with Thermo Guard freeze protection for the size 04-40 GOLD units. Extra accessories Valve set with 2(3)-way valve, actuator, anti-frost monitor sensor and connection cable with quick connector. Circulation pump for guaranteeing the anti-frost monitor function if an air heater without anti-frost protection is used. Supplied with T coupling, non-return valve and adjustment valve. Several capacity variants Circular or rectangular connections that fit the relevant size of GOLD unit (not applicable to all the capacity variants). Incorporated into its own insulated casing for the size 50/60 and 70/80 GOLD units. Extra accessories The TBVA Valve set consisting of 2(3)-way valve including actuator and connection cable. TBEK and TBLK Dual-purpose section For use in ventilation systems in which the extract air and/or outdoor air is highly contaminated. Filter of woven aluminium type or Class G3 compact filter. TBLE Electric air heater TBDA Silencer Size 04/05 and 08 GOLD units: Circular silencer. Sound attenuating material consisting of glass wool covered with EUROLON and perforated sheet steel. GOLD 14/20, 25/30, 35/40, 50/60, 70/80: Rectangular silencer with soundabsorbing material of Cleanolon-AL type. Several capacity variants Degree of protection IP43. Circular or rectangular connections that fit the relevant size of GOLD unit. Incorporated into its own insulated casing for the size 50/60 and 70/80 GOLD units. The integrated thyristor is controlled in response to signals from the GOLD air handling unit. Two series-coupled overheating protection devices Power must be supplied directly from the electrical distribution box. Incorporated into its own insulated casing for the size 50/60 and 70/80 GOLD units. Several capacity variants The TBEK combines an electic air heater and an air cooler for either chilled water or direct expansion. The TBLK combines an air heater for hot water and an air cooler for either chilled water or direct expansion. 18 Registered design. The company reserves the right to make design changes without prior notice.

Complements and accessories Duct accessories Dimensions H H L L B Duct accessories Size/B = width, H = height, L = length (mm) 04/05 08 14/20 25/30 35/40 50/60 70/80 Damper B 1040 1240 1440 1640 1840 TBSA H 315 400 440 540 640 840 1040 L 140 220 215 160 160 160 215 B 1000 1200 1400 1800 2000 Silencer H 315 400 400 500 600 800 1000 TBDA L 915 1200 650 650 650 650 1250 Air heater B 488 588 1119-1250 1319-1590 1526-1850 1747-2318 1947-2637 TBLA/TBLF H 405-428 528 438-605 538-755 638-880 838-1127 1038-1320 hot water L 300 300 148-300 148-300 148-300 148-570 148-570 Air heater B 314 400 1200 1400 1600 2318 2637 TBLE H 385 528 400 500 800 1127 1320 electric L 291 300 370-500 370-600 370-600 632-792 632-792 Air cooler B 488 688 1250-1495 1595-1790 1885-2085 2318 2637 TBKA, TBKC H 430 630 590-625 765-840 940-950 1127 1320 L 500 500 500 500 500 570 570 Dual-purpose B 2318 2637 section H 1127 1320 TBEK L 1716-1878 1716-1878 Dual-purpose B 2318 2637 section H 1127 1320 TBLK L 1654 1654 Prefilter B 500 600 1200 1500 1800 2475 2400 TBFA H 500 600 600 600 900 1000 1200 L 380 380 380 380 380 380 380 Registered design. The company reserves the right to make design changes without prior notice. 19

Complements and accessories Air recirculation section, GOLD RX and CX TBBR Air recirculation section The TBBR air recirculation section is available for the size 14 and larger GOLD RX and CX units. The TBBR consists of an extra unit section that has a motor-driven damper (on/off or modulating). Depending on how the air recirculation section is to be used, it may also be necessary to install extra sensors for reading the pressure, room temperature, CO 2 content, heating and/or cooling coil temperatures and the status of shut-off dampers for exhaust air and outdoor air. Recirculation, on/off: Can be used when it is desirable to heat an unoccupied room with recirculated air; an economic solution for factory buildings, shopping centres, etc. The intermittent night-time heating function stops the extract air fan and heat recovery, closes the shut-off damper for outdoor air and opens the damper in the air recirculation section. Recirculation, modulating: Can be used for the demand-controlled and economical operation of fans, heating and cooling, especially in buildings in which the load varies. The patent-pending ReCO 2 function adjusts the air quality (in response to signals from CO 2 sensors) and temperature by steplessly controlling the shut-off dampers and the damper in the air recirculation section as well as the speed of the fans. Normal operation. Outdoor air Supply air Extract air Exhaust air Recirculation, on/off: Extract air fan stopped, outdoor air and exhaust air dampers fully closed, damper in air recirculation section fully open. Recirculation, modulating Supply air fan runs at higher speed, outdoor air damper and air recirculation section open whenever required. Mixing section, GOLD SD TBBD Mixing Section The TBBD mixing section is available for the GOLD SD in all sizes. The mixing section can be used when it is desirable to completely or partially heat an unoccupied building with recirculated air; an economic solution for factory buildings, shopping centres, etc. The TBBD consists of a T-model spiral tube (sizes 04-08) or a rectangular duct with three connections for slip-clamp jointing (sizes 14-80). The mixing section can be ordered with an two or three dampers. Typical applications of the mixing section for the GOLD SD Normal operation. Mixing. The three dampers open whenever required. Outdoor air Supply air Extract air Exhaust air 20 Registered design. The company reserves the right to make design changes without prior notice.

Complements and accessories Plug and Play cooling unit for direct expansion CoolDX Cooling unit The CoolDX is a complete system for comfort cooling in GOLD RX/PX/CX air handling units. The CoolDX operates with direct expansion in which the refrigerant transfers cooling energy via a pipe system with coils. The cooling unit operates in 3 steps. A special function provides stepless control as well. The heat exchanger in the GOLD is then used in parallel with the cooling compressors. All the equipment is housed in one and the same unit and the CoolDX can be docked to the GOLD across ordinary duct connections. In addition to the above, only an electric power supply and a communication cable (with quick connector) between the CoolDX and the GOLD are required. The GOLD has ready-to-use cooling functions for controlling the CoolDX. This also includes communication via the web or traditional supervisory systems. The CoolDX is available in several capacity variants for the size 08-60 GOLD units. A floor stand is available as an accessory for the size 08 units. Base beams are standard for the size 14-60 units. GOLD CoolDX Outdoor installation TBTA Roof The roof is supplied in kit form, complete with the necessary assembly parts and sealing strips. Visible parts are made of sheet steel painted in a beige colour tone, NCS S2005-Y 30R. A roof cannot be installed on units with upward air discharge from the fan outlet. Cover hood is available for protecting the pipework package on the GOLD CX installed outdoors. Exhaust air hood Intake air section Roof GOLD units can be installed outdoors if they are equipped with the roof, air intake section and exhaust air hood accessories. The illustration shows the roof for the size 04-40 GOLD RX units. TBTA Intake air section The intake air section is made of aluminiumzinc plated sheet steel and has rectangular dimensions for all the GOLD sizes. Space is available inside for a possible intake air damper. The intake air section is designed to be secured by means of screws to the end wall panel of the air handling unit. TBTA Exhaust air hood The exhaust air hood is made of aluminium-zinc plated sheet steel and is equipped with protective netting. Circular for GOLD sizes 04/05 and 08 and rectangular with slip-clamp connection for the other sizes (the slip clamps are included). Duct accessories for outdoor installation Damper and silencer for all the GOLD unit sizes and air heater and air cooler for the size 50-80 GOLD units can be installed outdoors by means of special accessories. Registered design. The company reserves the right to make design changes without prior notice. 21

Complements and accessories Hoods Roof hood Wall hood TBHA Outdoor air hood TBHB Exhaust air hood TBHC Dual-purpose hood TBHE Exterior Wall Hood The TBHA outdoor air hood, the TBHB exhaust air hood and the TBHC Dualpurpose hood are made of aluminium-zinc plated sheet steel covered with a Plastisol (black) surface coating that conforms to Environmental Class C4. The roof duct is made of galvanized sheet steel, lined inside with 50 mm thick insulation to Fire-resistance Class EI30, with a surface covering of type-approved synthetic woven fabric. Two angle brackets for connecting the duct to a roof with relevant slope are included. TBHA Outdoor air hood Air intake grille fitted with wire mesh on both sides. Hinged hood. For GOLD, size 04-40. TBHB Exhaust air hood Wire mesh grille on top. Hinged hood. Equipped with drainage means. For size 04-40 GOLD units. TBHC Dual-purpose hood Combination of TBHA Outdoor air hood and TBHB Exhaust air hood For size 04/05 and 08 GOLD units. TBHE Exterior Wall Hood Aluminium-zinc plated sheet steel covered with a Plastisol (light grey) surface coating that conforms to Environmental Class C4. For the admission of outdoor air and the discharge of exhaust air. The exhaust air is horizontally discharged through a circular wire mesh grille at the front of the hood. Outdoor air is admitted through a wire mesh grille at the bottom of the hood. This design effectively prevents short-circuit flow between the outdoor air/exhaust air. For size 04/05 and 08 GOLD units. Mechanical equipment Stand/Set of support legs Specially designed stand/sets of support legs are available for all the size 04/05 and 08 GOLD variants. The height enables the running of cables under the air handling unit. Supplied as an assembly kit. The stand can be used as a base without legs and is also suitable for vertical installation. Cover holder Consists of a mechanic stay with latch. Supplied in unmounted condition. Facilitates servicing and maintenance of vertical units. Support foot, Support foot, Rubber disc 105 Adjustable support foot for compensating unevenness or sloping of the floor. To be fitted to the base beam of the air handling unit. For size 14/20, 25/30, and 35/40 GOLD units: At least 6 support feet are recommended. For size 50/60 and 70/80 GOLD units: At least 12 support feet are recommended. Rubber disc: Designed to be glued under the support foot. Water trap Water trap for the drain branch of the coil heat exchanger. Heating cable for drainage Used for preventing water from freezing in the drainage line. Droplet eliminator Droplet eliminator for coil heat exchangers. Slip-clamp jointing flanges Set of slip clamps in appropriate lengths for one joint. Metu connection Type Metu connection frame. 22 Registered design. The company reserves the right to make design changes without prior notice.

Complements and accessories Electrical and control equipment Presence detector If switching between high-speed and lowspeed operation by means of a timer isn t desirable, this can be carried out by the controller in response to signals from type ELQZ presence detectors. Pressure sensor For use in conjunction with the VAV pressure control function, when it is necessary to keep the pressure constant in the ductwork. Can also be used in conjunction with the heat exchanger defrosting function, when it is necessary to control the pressure across the heat exchanger. The connection cable is included; 1 15 m long cable can be selected. Air quality sensor For use in conjunction with the demandcontrolled VAV function, when the airflow of the air handling unit must be variably controlled by means of an air quality sensor. Available for duct or room mounting. Room sensor, outdoor/room sensor Used in conjunction with functions that require outdoor or room temperature readings. For wall mounting. Available for Degree of Protection IP20 or IP43. Extra hand-held micro terminal Can be used if it is desirable to control GOLD units from a another location. The GOLD can manage a total of 3 hand-held micro terminals. 3 m long connection cable and holder are included. MMC circuit card Multi-media circuit card for program transmissions and logging Transformer, 230/400 V For connecting the air handling unit to 230V mains power supply Transformer, 230/24 V AC For connecting 24 V AC electrical components to 230 V mains voltage. IQnomic Plus Functional module for extra functions including connection cable ReCO 2 Complete set of components for controlling the function for mixing. Pressure sensors and the IQnomic Plus are included. Air quality sensor must be ordered separately. The outdoor air damper must be of modulating type. Control of air heater for preheating Including temperature sensor for installation in a duct and the IQnomic Plus with a 0.25 metre long cable. Humidity sensor, IQnomic Plus Humidity sensor for the IQnomic Plus module. For dehumidification and dew point control Timer Can be used for overtime operation in conjunction with the external high speed and external low speed functions. For strap-on mounting. Timer, electronic Can be used for overtime operation in conjunction with the external high speed and external low speed functions. For strap-on mounting. Push button Can be used for overtime operation in conjunction with the external high speed and external low speed functions. For strap-on mounting. Can be selected with or without indication. Extension cables 5 m long for supply air temperature sensor, air heater for water or electric 1-15 m, for hand-held micro terminal, pressure sensor and IQnomic Plus. 6-50 m, for hand-held micro terminal Fire and smoke protection The fire and smoke protection function consists of three separate units: ELQZ equipment cubicle, ELQZ smoke detector and ELQZ damper actuator. Separate cubicle for Xzone The function is designed for one extra temperature zone. TBLZ Communication unit Communication via TCP/IP, EIA 485 and EIA 232 as well as via internal webserver is standard in the GOLD. The extra TBLZ communication unit is required for communication via LON FTT-10 - Lon Works and Trend. Modem Analogue or GSM. Can be used when direct connection cannot be made to a network or communication system. Several units can be connected to the same modem. Pipework package for the GOLD SD TBXZ Pipework package The pipework package with controller is used in the GOLD SD with coil heat exchanger. The following is included in the supply: The pipework package is supplied complete with insulated sheet-metal casing, control valve with actuator, expansion vessel, safety valve, manometer and shutoff cocks, thermometers, filling valve and air purging valve. Work to be carried out at the building site: Install the pipework package and controller at an appropriate place. Pipe route with insulated pipes to the air handling unit. Electrical connections between the controller and the pipework package. Filling water mixed with glycol. Registered design. The company reserves the right to make design changes without prior notice. 23

GB Overview, GOLD 2007-05-17 www.swegon.com