PLESE DO NOT RETURN THIS PRODUT TO THE STORE! OWNER S MNUL ENLOSED The owner s manual includes assembly and operating instructions, safety warnings, and the parts and hardware lists. If you have questions about the assembly or operation of this product, are missing parts, or have defective parts, please e-mail us at customerservice@vdgus.com Or, call us toll-free (M-F 8:30 M to 4:30 PM entral Standard Time) at 1-866-561-0731
ELETRI FIREPLE MNTEL and INSERT OWNERS MNUL Model: KEMHJR orner onfiguration Flat onfiguration WRNING! Read and understand this entire owner s manual, including all safety information, before using this product. Failure to do so could result in personal injury. Only use this mantel as described in this manual. ny other use is not recommended by the manufacturer, and may cause personal injury. WRNING! Only use this mantel with model 23-EFILED / EF-36 electric fireplace insert! Failure to do so may cause fire, electric shock, or other personal injury, and will void all warranties. UTION! Keep this owner s manual for future reference. If you sell or give this product away, make sure this manual accompanies this product. 2
IMPORTNT SFETY INSTRUTIONS! WRNING Read all instructions before using the mantel and electric insert heater! DO NOT USE OUTDOORS! DO NOT run power cord under carpeting. DO NOT cover power cord with throw rugs, runners, or similar coverings. DO NOT route power cord under furniture or appliances. rrange power cord away from traffic area, and where it will not be tripped over. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock or fire, or damage the heater. To prevent possible fire, DO NOT block air intakes or exhaust in any manner. Doing so could cause a fire. DO NOT use on soft surfaces, like a bed, where openings may become blocked. heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored. Use this heater only as described in this manual. ny other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. LWYS plug heaters directly into a wall outlet/receptacle. NEVER use with an extension cord or relocatable power tap (outlet/power strip). LWYS keep electric cords, home furnishings, drapes, clothing, papers, or other combustibles at least 3 feet (0.9m) away from the front of this heater, and away from the bottom, sides, and rear of this heater. DO NOT place the heater near a bed because objects such as pillows or blankets can fall off the bed and be ignited by the heater. VOID FIRE! Regularly inspect all air vents to make sure they are free from dust, lint, or other blockage. Unplug the unit and clean with a vacuum ONLY. DO NOT rinse or get wet. WRNING Use only the electric insert and included mantel. NEVER use a mantel from another maker. NEVER use this electric fireplace insert unless it is properly installed in the correct mantel. Use extreme caution if using this heater near children, or where children may be present. NEVER leave this heater unattended. LWYS unplug this heater when not in use. This heater is hot when in use. VOID INJURY! DO NOT TOUH hot surfaces, or attempt to move this heater while it is hot. LWYS turn this heater off before unplugging it from the outlet. Discontinue use if this fireplace malfunctions or is dropped or damaged in any manner. VOID INJURY! Keep the cord from crossing traffic areas to avoid tripping. Prevent tipping and avoid personal injury! If placing a TV on this mantel, follow all manufacturer instructions included with your TV for safely securing the TV to the wall. 3
WRNING Risk of electric shock! DO NOT OPEN! No user-serviceable parts inside! LWYS disconnect this unit from the power supply before performing any assembly or cleaning, or before relocating the electric fireplace. NEVER leave this heater unattended. LWYS unplug this heater when not in use. LWYS store this heater in a dry location. NEVER use the fireplace if it has become wet. NEVER use this heater in bathrooms, laundry rooms, or any other location where the heater could fall into a bathtub or pool, become damp or come in contact with water. NEVER operate this heater if the power cord or plug has become damaged, or if the grounding pin is damaged or missing. Place the heater near a wall outlet so an extension cord is not needed. If an extension cord is needed, the gauge of the cord must be at least 14WG, and the rating must be at least 1875 Watts. NEVER use a smaller gauge cord with a lower rating. Doing so may result in fire or electric shock. ONLY use this heater on a 110~120 Volt 15 mp grounded circuit. NEVER overload the circuit. If this heater trips the circuit breaker, unplug all other appliances on the same circuit before the next use. void plugging other appliances into the same circuit as this heater. NEVER plug this heater into an outlet that is old, cracked, or has any loose wires or connections. Plugging this heater into a faulty outlet could result in electric arcing within the outlet that could cause the outlet to overheat or catch fire. LWYS check your heater cord and plug connections with each use! i) MKE SURE the plug fits tight in the outlet! Faulty wall outlet connections or loose plugs can cause the outlet to overheat. ii) Heaters draw more current than small appliances. Overheating may occur even if it has not occurred with the use of other appliances. iii) During use check frequently to see if the plug outlet or faceplate is HOT! iv) If the outlet or faceplate is HOT, discontinue use immediately and have a qualified electrician inspect and/or replace the faulty outlets. The power cord supplied with the heater has three prongs: two flat blades (live and neutral) and one round pin (ground). If a 3- slot receptacle is not available, an adapter MUST be used. The adapter MUST be properly grounded to the outlet box (see figure at right). [NOTE: dapter NOT INLUDED.] SVE THESE INSTRUTIONS! 4
PREPRTION NOTE: Remove all parts and hardware from the carton and place them on a clean, soft, dry surface. heck the parts list to make sure nothing is missing. Dispose of packaging materials properly. Please recycle whenever possible. Tools required for assembly: Phillips screwdriver (Not included) PRTS & HRDWRE Item Description Qty 1 ase Panel 1 2 Left Front Panel 1 3 Right Front Panel 1 4 Left Side Panel 1 5 Right Side Panel 1 6 Shelf Panel 1 7 Top Front Panel 1 8 Top enter Panel 1 9 Top Rear Panel 1 10 Lower race 1 11 Rear Upright 1 12 Upper race 1 13 Door 1 14 ack Panel 1 2 4 Item Description Qty Item Description Qty Item Description Qty Long llen olts 23 E llen Wrench 1 I Door Knob Screws 2 Washers 18 F Door Hinges 2 J1 Door Stop Magnet 1 Short llen olts 24 G Door Hinge Screws 12 J2 Door Stop Plate 1 D L rackets 12 H Door Knobs 2 K Door Stop Screws 4 13 7 6 1 8 14 9 10 12 11 3 5 D E F G H I J1 / J2 K NOTES ON SSEMLY DO NOT fully tighten the bolts until the end of each step. This will allow you to make adjustments. NEVER use power tools, or over-tighten the bolts. Doing so may damage the wood. Tighten bolts until they are snug, and the assembled pieces are stable. The assembly process may require two capable adults to move pieces into place. Once assembled, the finished mantel should be moved by two capable adults. ssemble the mantel near where the fireplace will be used. Leave room to access the rear of the mantel to make it easier to install the electric fireplace insert. 5
SSEMLY K K J1 Front 12 7 9 8 Step 1: ttach Door Stop Magnet (J1) to Top Front Panel (7) with two Door Stop Screws (K). Magnets should face toward the front. Secure screws with Phillips screwdriver. (Flat onfiguration: Proceed to Step 2. orner: omplete Step 1, then proceed to Step 2.) lign Top Front Panel (7), Top enter Panel (8), and Top Rear Panel (9). Thread six Long llen olts () through Washers (), then through tabs and into holes in panels. Thread three Long llen olts () through holes in Upper race (12) and into Top Panels (7/8/9). heck alignment and tighten all bolts securely with llen Wrench (E). 3 2 5 4 D Step 2: ttach Right Side Panel (5) to Right Front Panel (3), and Left Side Panel (4) to Left Front Panel (2). Note: Images above show panels from rear. Thread a Short llen olt () through each hole in L racket (D) and into panel holes. Repeat for other three L rackets. heck alignment and partially tighten bolts with llen Wrench (E). 6
4 2 3 7 5 14 14 Step 3 (Flat onfiguration): Turn Top Front Panel (7) over on a clean soft surface. Set Side Panel assemblies (3/5 & 2/4) onto Top Panel. Slide ack Panel (14) into grooves in Left/Right Side Panels (4/5). Thread six Long llen olts () through Washers (). ttach Side Panel assemblies to Top Panel with bolts as shown. Tighten all bolts securely with llen Wrench (E). 2 4 7 3 5 14 8 12 14 9 Step 3 (orner onfiguration): Turn Top Panel assembly (7/8/9/12) over on a clean soft surface. Set Side Panel assemblies (3/5 & 2/4) onto Top Panel. Slide ack Panel (14) into grooves in Left/Right Side Panels (4/5). Thread six Long llen olts () through Washers (). ttach Side Panel assemblies to Top Panel with bolts as shown. Tighten all bolts securely with llen Wrench (E). 7
G F G I K I F 6 H J2 13 H Step 4: lign hinge holes in Door (13) and Shelf Panel (6). ttach Door Hinges (F) to Shelf and Door with twelve Door Hinge Screws (G). Tighten securely with Phillips screwdriver. ttach Door Knobs (H) to Door with Door Knob Screws (I). ttach Door Stop Plate (J2) to Door with Door Stop Screws (K). 6 14 Step 5 (Flat and orner onfiguration procedures are the same): ttach Door/Shelf assembly (6/13) to mantel assembly. Set the groove at the back edge of the Shelf (6) onto the ack Panel (14). Thread four Long llen olts () through Washers (). ttach Shelf to Side Panels with bolts as shown. Tighten all bolts securely with llen Wrench (E). 8
D D 1 D 1 Step 6 (Flat onfiguration): Set mantel assembly onto ase Panel (1). Thread Short llen olts () through holes in L racket (D) and into panel holes. Repeat for the other five L rackets. heck alignment and tighten all bolts securely with llen Wrench (E). 11 D D 1 11 1 10 10 Step 6 (orner onfiguration): Set mantel assembly onto ase Panel (1). Thread Short llen olts () through holes in L racket (D) and into panel holes. Repeat for the other five L rackets. Thread two Long llen olts () through ase Panel (1) and into Lower race (10). ttach Rear Upright (11) to Upper race (12) and Lower race (10) with two Long llen olts () and two Washers (). Tighten all bolts from all steps securely with llen Wrench (E). 9
Step 7: With the help of a second capable adult carefully lift the mantel from below. NEVER lift the mantel just from top. arefully move the mantel near where the fireplace will be placed. Leave space at the rear of the mantel to enable installation of the electric insert. Refer to the Safety Information and Warnings on pages 3 and 4 for instructions concerning the safe positioning of the fireplace relative to flammable objects, safe electrical outlets, etc. WRNING NEVER sit, stand, or climb on fireplace. Doing so could cause serious personal injury or property damage. ELETRI FIREPLE INSERT See the Electric Fireplace Insert instruction manual for information about installation of the insert into this mantel, as well as the safe operation of the fireplace. The Important Safety Information and Warnings contained on pages 3 and 4 of this manual apply to both the electric fireplace insert and the mantel. See the electric fireplace insert manual for additional safety information and warnings. \ RE leaning LWYS turn the heater OFF and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this fireplace. Failure to do so could result in electric shock, fire, or personal injury. NEVER immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury. 10
Wood: Use a vacuum cleaner or duster to keep the product free from dust and dirt. Do not use any abrasive cleansers, liquid sprays, or any other cleaner that may scratch or damage the surface. Vents: Storage: Use a vacuum or duster to remove dust and dirt from the heater and vent areas. lean the exterior of the fireplace with a slightly damp cloth or duster. Store heater in a clean dry place when not in use. LIMITED WRRNTY This warrants to the original purchaser that this product is free from defects in material and workmanship as of the date of purchase and that it will, under normal use and proper care, remain so for one year from the date of purchase. Missing or initially defective parts will be replaced free of charge during the period of this limited warranty. The original dated sales receipt is required for all warranty claims. This warranty does not cover damage which has occurred during transport from the point of purchase to the consumer s home. This warranty does not cover glass, light bulbs, remote controls, or batteries. This product is for residential use only. ny and all commercial use of this product voids all warranties, and frees the manufacturer from all liability. Read and understand all assembly and operating instructions, and all safety information and warnings, before use. The following will void this warranty: Damage caused from tampering with, modifying, or altering the fireplace insert in any manner; Damage due to incorrect assembly, improper care, misuse, or abuse; Damage from being used with the wrong power source; Water damage; Damage caused from this insert being used outdoors; Damage caused from this insert being used for excessive periods of time; Damage caused by the insert being used in a commercial application; Damage from use as a primary heat source; Other misuse or abuse not specifically listed herein. This product is not intended to be used as a primary heat source. Vendor Development Group, Inc.(hereafter, VDG), its directors, officers, or agents, will not be liable to the purchaser or any third party, whether in contract, in tort, or on any other basis, for any indirect, special, punitive, exemplary, consequential, or incidental loss, cost, or damage arising out of or in connection with the sale, maintenance, use, or inability to use this product, even if VDG, or its directors, officers, or agents have been advised of the possibility of such losses, costs or damages, or if such losses, costs, or damages are foreseeable. In no event will VDG, or its officers, directors, or agents be liable for any direct losses, costs, or damages that exceed the purchase price of the product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to the purchaser. This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Thank you for purchasing this product! If you have questions about the assembly or operation of this product, are missing parts, or have defective parts PLESE DO NOT RETURN THIS TO THE STORE! Instead, please e-mail us at customerservice@vdgus.com Or, call us toll-free (M-F 8:30 M to 4:30 PM entral Standard Time) at 1-866-561-0731 VDG, Inc. Minneapolis, MN 55401 Made in hina 11
PLESE DO NOT RETURN THIS PRODUT TO THE STORE! OWNER S MNUL ENLOSED The owner s manual includes assembly and operating instructions, safety warnings, and the parts and hardware lists. If you have questions about the assembly or operation of this product, are missing parts, or have defective parts, please e-mail us at customerservice@vdgus.com Or, call us toll-free (M-F 8:30 M to 4:30 PM entral Standard Time) at 1-866-561-0731 12