2016 Maks 4M OOD, All rights reserved. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 1/25
MAKS 4M OOD 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street Bulgaria tel.:0879990542 Technical support +359 878700840 selling@prity-eu.com We have taken all possible measures to guarantee the accuracy and completeness of the present documentation. Since we cannot exclude the possibility for an error, we will be grateful if you share your suggestions or any further information, which could improve this documentation. Email: marketing@prity-eu.com We would also like to point out that the software and hardware terminology, as well as the proprietary trademarks, used and/or mentioned in this manual, are generally copyright protected. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 2/25
1. Notes related to the documentation Always keep this documentation safe! This documentation is part of the product. For this reason, keep safe the documentation for the entire period of operation of the product. Hand over the documentation to any subsequent user. Make sure that the documentation will be supplemented by remarks and additional documents concerning any upgrade or modification introduced. 1.1. Documentation validity This documentation is applicable only for the pellet burner with programmable electronic controller model: Table 1: Variants Item Number/Variant PPB50 PPB30 PPB20 Designed for For pellet burner 50kW For pellet burner 30kW For pellet burner 20kW Validity of the documentation for the mentioned variants: Unless otherwise specified, the information in this documentation is valid for the mentioned variants. Pellet burner PPB20/30/50 must be installed and operated in compliance with this instruction Follow the instruction for operation of the pellet burner and the system is was integrated to! In addition to the present instruction You must observe the requirements for operation, specified in the pellet burner manufacturer instruction. 1.2. Copyright This instruction, including all figures and illustrations are copyright protected. Any reproduction, translation, as well as any electronic supplementing or photo-technical addition or backing up (such as photo-copying) can only be done upon written permission. 1.3. Symbols Hazard of injury Designates high risk and hazardous situations, which if not avoided, could result in severe injury or death. Electric shock hazard! Designates high risk and hazardous situations, which if not avoided, could result in severe injury or death. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 3/25
Injury hazard! Designates high risk and hazardous situations, which if not avoided, could result in severe injury or death. Injury hazard! Designates low risk and potentially hazardous situations, which if not avoided, could result in light or medium injuries. Property damage hazard! Designates potentially hazardous situation, which if not avoided can lead to property damage! Electrostatic discharge property damage hazard! Designates potentially hazardous situation, which if not avoided can lead to property damage. 2. Important notes! Този section contains summed-up information from the general requirements and safety guidelines for each of the following sections. We recommend that you make yourselves familiar and diligently follow the safety guidelines in order to preserve your life and health and prevent any damage to the devices. 2.1. Legal framework 4 Modifications Maks 4M OOD reserves its right to introduce any kind of modifications and revisions, aiming at improving the performance and technical progress. All third party products shall be mentioned without reference to their patented rights and thus, any presence of ones is possible. 5 Personnel qualification All actions, related to installation, cabling and programming of PPB pellet burner must be performed by qualified specialists with the required expertise. Such specialists must be familiar with the specifics of the device and the applicable national standards. 6 Using PPB20/30/50 pellet burner in compliance with the applicable provisions. PPB pellet burner is designed for building-in and may not be used without performing the additional actions in order to comply with the operating regional and national standards. The pellet burner is capable of receiving and processing discrete and analogue signals, and issuing control commands to the actuating mechanisms and transmit data to devices of higher hierarchical level within the control system. It has been designed to integrate water heating boilers. No protection has been provided against injuries of limbs, or ingress of dirt and water. Unless otherwise specified, usage of the burner in dusty and humid environments shall be forbidden. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 4/25
7 Technical state of devices The pellet burner comes with factory pre-configured hardware and software, which meet individual requirements. Maks 4M OOD shall not be held liable in cases of unauthorized modification to the controller s hardware or software, as well as in case of its use not as intended. Please, send your inquiries for modifications or for new hardware and software directly to the manufacturer, Maks 4M OOD. 2.2. Safety tip (precaution) The following precautions must be taken into account during installation and operation of PPB pellet burner: Do not operate the device, when it s energized! All sources of power supply to the device must be switched off and disconnected before performing any installation, repair or correction work! Installation of the pellet burner! Burner installation must be done by specialized qualified personnel following all instructions and potential local provisions in compliance with the good technical practice rules. The location for installation and the method for connection of the burner must be carefully selected, in compliance with all safety guidelines. Servicing the burner must be done by an adult person that is familiar with the operation conditions. The burner may not be used by children less than 8 years old or people with limited physical, sensory or mental capacities, or ones with insufficient experience and knowledge, unless these are supervised or instructed concerning the safe use of the device and understand the potential hazards. Children must not be allowed to play with this device. Unsupervised children may not perform cleaning or servicing of the device. Replacement of malfunctioning or defective burners! Replacement of defective or malfunctioning devices (as a result from improper operation, or improper installation cannot be provided. Protect the device against substances of seeping or insulation properties! Never attempt to modify the burner! Usage of liquid kindling is forbidden! It is absolutely forbidden to bring readily flammable and volatile liquids into the room where the burner is operating. Use only approved detergents for cleaning! Use dry compressed air or ethanol soaked cloth to clean all sticky contacts. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 5/25
Safe distances! Install away from flammable objects! Safe distances, which must be observed during installation of burners, stoves, boilers and flue pipes must be minimum of 200 mm, in case there are materials with flammability class А, В, С1 nearby and minimum of 400 mm in case there are materials with flammability class С3 nearby. Do not allow wrong connections! Do not allow wrong connection of inputs, outputs and power supply, as this can damage the device. Avoid electrostatic discharge! The controller is equipped with devices, which can be damaged by electrostatic discharges caused by accidental touch. Please, make yourselves familiar with the requirements for safety in cases of electrostatic discharge of the standard EN 61340-5-1/-3. Use of pellets! The burner is designed to burn only wood pellets class А2 and А1 according to BDS EN ISO 17225-2:2014 Solid biofuels. Fuel classes and specifications. Part 2: Graded wood pellets with ash contents up to 1.5%, without contents of chemically treated and recycled wood. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 6/25
3. Description of the device Smart pellet controller (SPC) for PPB20, PPB30, PPB50 is a multi-functional electronic controller, which is integral part of the common system for control and automation Smart Home. It is designed to perform flexible control of complex systems of actuating mechanisms and devices, by means of reading and analysis of all incoming input signals following dedicated pre-set algorithms. All necessary sensors and mechanisms are connected directly to it. The opportunity for communication between controllers and devices from Smart Ctrl-V1 series, virtually makes it possible to take the readings analysing and controlling of any type of systems and installations. Smart Ctrl-V1 series controller is based on processing solution allowing installation of basic software for running algorithms within a pre-set task. The option to update the system at any moment, allows optimization of the algorithms and addition of new functionalities. The access to the options of the controller is provided by a display of Smart D-V1 series and a computer using specialized software, and furthermore, over the Internet depending on the connection method selected (WI-FI or 3G) using remote server. Thanks to the convenient menus specially developed according to the set requirements, adjustment of all operating parameters Smart Ctrl-V1, can easily be customised to all requirements and systems. Electronic controller This is a multifunctional electronic micro-processor controller, which runs algorithm for control of pellet boiler / stove / burner. The particular application of the controller is determined by the type/version of the configuration file preprogrammed in the memory. The controller configuration is implemented by adjustment of the process parameters. The setting can be done using the user-friendly menu of the display or by means of specialized software, installed on the computer. The controller can be integrated in pellet boilers / stoves / burners, which have the following actuating mechanisms: Feeding auger Dosing auger Combustion air fan Flue gas fan Purge fan Lighter (heater) with heating capacity up to 1,5kW; Circulation pump, heating Circulation pump/three-way valve, domestic hot water *All outputs of the controller can be pre-configured in compliance with the particular technical solution of the manufacturer, via installation of dedicated firmware. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 7/25
Functionality: The controller provides: Preliminary purging /cleaning/ of the firebox Control of flame put-out Process control of burning intensity. Visual and acoustic signalling for running the program, visualized on a bright display including text and graphics. Option for control of external devices Control in case of faulty fan Control in case of broken glass or open door Control in case of flame flashback Automatic control of the heating capacity in ON/OFF mode and three-stage modulation, with option for limiting the heating capacity. Automatic dosing of the fuel quantity; Automatic activation of feeding /external/ auger Adjustment of the combustion air Integrated electrical circuit breaker User interface: The controller comes complete with operator panels SmartD-V1 and Smart-DT, which provide easy and userfriendly control of stove and burner operation. The display shows a good deal of information, represented by graphic symbols and text. - Current time time and date - Accumulated alarm messages or connection with computer - Water temperature in the heat exchanger - Pre-set temperature - Operation mode - Current status The operator panel has: SmartD-V1 - four physical buttons, and SmartDТ-V1 four on-screen buttons for switching on and off of the device, options for navigation within the menu and modification of parameters. In order to secure the controller against unwanted actions, some of the main functions of the controller are accessible upon pressing and prolonged holding of some the buttons or input of access password. Detailed information is provided in the Instruction for operation - section 4. Operator panel. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 8/25
3.1. Specifications: Description Heating capacity Consumption of pellets Parameters 10 ~50 kw P1 First stage 2 kg/h P2 Second stage 7 kg/h P3 Third stage 10 kg/h Required electrical power for ignition Required electrical power for burning 0,4 kw 0,1 kw Description Parameters 1. Power supply: 230Vac +10% 50Hz 2. Controller input power <3W 3. Real-time clock RTC clock, calendar 4. Accumulator battery, autonomy >2 years; 3V 5. Maximum cross-section of connecting wires 2.5mm2 6. Additional power supply for sensors 12V DC 7. Serial interface connection (PC) RJ 11(4p) 8. Serial interface connection (Display) RJ 11(6p) 9. Sensor inputs TC Flue gase sensor TC, type K), tmax=650 C RT Room thermostat NTC 10kΩ/ON/OFF, tmax=150 C IRS Photo-resistive cell type QRB1 RB Backfire sensor KSD250V - 70 C /10A B Water jacket temperature sensor NTC 10kOhn tmax=150 C DHW Domestic hot water temperature sensor NTC 10kOhn tmax=150 C HALL Encoder Hall сензор Pressure Differential pressure transmitter dp = -50 to+50 Pa LED/PHT Pellet level sensor (IR barrier capacitive sensor); IR-LED/PHT 10. Actuating mechanisms outputs FM Reserve (motor/on/off/ etc.) 230V / 300W (exp 500W) EGF Fan 230V / 300W (exp 500W) EXF Auger external 230V / 300W (exp 500W) FEED Dosing auger 230V / 300W (exp 500W) PUMP Pump heating 230V / 300W (exp 500W) DHWP Pump DHW 230V / 300W (exp 500W) CLE Fan purging 230V / 300W (exp 500W) ING Heater 230V, max 1500W * All outputs of the controller can be pre-configured in compliance with the particular technical solution by means of installation of specialized firmware. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 9/25
3.2. Wiring diagram: 3.3. Options: Description 1. Operator panel HMI/V1 2. Sensor panel Be150302 3. Software SPC/W/A/B 4. Wi-Fi module wi-fi 5. GSM module 3G 6. Communication cable to the USB port USB Com 7. Remote access Data Server 8. Mobile version SPC/App * connection of several simultaneously operating operator or sensor panels is possible. ** a wi-fi or 3G module to be installed at the operator panel is required for the connection to the Data Server. *** only one wi-fi or 3G module can be integrated into one operator panel (sensor panel). 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 10/25
4. Dimensions of the burner. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 11/25
5. Schematic diagram. 1. Control panel 2. Pellets input 3. Connection flange with sealing 4. Firebox with heater and grate 5. Body of the burner 6. Fuses 7. Outlets for power supply and control of peripheral devices 8. Main power supply 9. Feeding auger 10. Auger pipe 11. Gear motor 12. Auger power supply cable 13. Temperature resistant hose 14. Stand 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 12/25
6. Installation instruction. 6.1. Connection to the pellet hopper: The pellets are stored in a hopper, where the auger pipe is inserted at an angle of approx. 45 degrees. In case the pipe was installed under greater angle, there is a possibility that the auger will be blocked as a result from the hindered movement of pellets. If this happens, resuming work must be done after all blocking pellets have manually been removed from the pipe. The auger takes pellets from the hopper, doses them and feeds them into the firebox. The liquid circulating in the heating system is heated as a result from the burning done in the firebox. The combustion gases are taken into the atmosphere via the chimney. The operation of the pellet burner is controlled by the multifunctional electronic controller. 6.2. Connection to the boiler: The burner is designed to work with a heating appliance, in the firebox of which negative pressure /chimney draught/ of at least 20 Ра must be maintained. The boiler is to be installed in such a way as to provide sufficient space for cleaning, elimination of soot and ash from the burner, the firebox and the flue gas pipes. The burner is installed in the opening of the firebox door and includes the respective gasket. It is fitted with bolts and nuts. The connection between the burner and the boiler must be well sealed to prevent any combustion gas leakage into the room. During installation the burner must be in horizontal position. The pellet feeding hose must be straightened and all connections must be tight. 6.3. Connection to the electrical mains: Once the burner is fitted to the boiler, the technician must connect it to the control device and then, connect it to the electrical mains. This connection must be performed by licensed electrician, paying special attention to the protective earthing of the device. Power (230V). Caution! High voltage! POWER Mains power supply 220V ±10%. Take all necessary measures to keep the position of the live wire (L); If the power supply cable of the burner is damaged, it can only be replaced by a qualified person. 6.4. Connection of external devices to the controller: Connection of external devices is to be done using screw block terminals. The maximum cross-section of the conductor is 2.5mm 2. For clarity during connection and for prevention of wrongful connection, all inputs are on the left side of the controller, and all outputs on the right one. The specialized external devices display, personal computer, sensor for speed of rotation are to be connected to individual terminals, which will prevent wrongful connection. Description of inputs and outputs Power (230V). Caution! High voltage! CLE Purge fan. Power supply of high-pressure auxiliary fan for purging the burner/the stove; DHWP Domestic hot water pump/three-way valve. Power supply of the re-circulation pump or three-way valve of the circuit for preparation of domestic hot water; PUMP Circulation pump. Power supply of the circulation pump of the main heating circuit; EXF External feeding auger. Power supply of external discharging auger for pellets. FM Reserve; Operation: TC Thermocouple type K, for measurement of flue gas temperature. RT Room thermostat, Normally open contact or NTC 10K temperature sensor. B Sensor for temperature of the working fluid (the water), NTC 10K for measurement of temperature of the water in the water jacket of the stove/the boiler. DWH Domestic hot water temperature sensor. NTC 10K for measurement of temperature of the water in the water tank for domestic hot water. Pressure Sensor for discharge/pressure. High sensitivity differential pressure transmitter. When measuring vacuum connect the flexible hose of the left stub pipe. PC Communication port for connection with computer. Use communication cable USB Com. OP Operator panel. Port for connection to the operator panel. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 13/25
6.4. Connection of the pellet feeding auger: Position the auger conveyor so that loading it with pellets from the hopper will be unobstructed. The auger conveyor is supplied with power using plug connector. Its initial filling is performed automatically, along with starting-up of the burner. The working condition of the auger power supply cable is connected through its plug to the dedicated socket in the body of the burner, and it is being controlled following a pre-defined algorithm. 6.4. Connection of room thermostat: If a room thermostatic controller is connected to the burner, it must be verified whether its pre-set temperature is not less than the one of the room it was installed. Where room thermostat is missing install a bridging connection! 7. Operator display. The operator display is used for visualization and adjustment of the parameters of the pellet controller. It has four control buttons. The Enter (Start/Stop) button has double functionality: - Prolonged pressing and holding - pressing and holding for more than 3sec. starts up or stops the stove. - Single pressing confirms the selected function or value when working with the menu. When pressing the BACK button in the main screen, it loads the menu of the controller, and when working within the menu structure, it takes you one level up without confirmation. The buttons move the cursor along the icons of the menu and set values of the parameters. Main screen: system. Using buttons at the Main screen level you can change the pre-set temperature of the water in the heating 8. Operation modes: The user s provided with option for selection between four operation modes: - Heating; - Heating along with production of domestic hot water - Heating and priority production of domestic hot water - Summer mode production of domestic hot water * The option Solar controller (differential thermostat) /optional/ can be activated for each of the modes. The controller controls the stove/the boiler in compliance with the operation mode selected by the user and the need of heat supply. It provides automatic control of the heating capacity. Sequence of processes: 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 14/25
11:25! E Готовност 60 sec 15.03.2015 23 C 80 C 60 C Standby The burner is ready for work. No command for working has been issued. Required conditions to move to the next mode: * Command for starting of the burner: Pressing and holding the button Start for more than 3 sec. *In Heating mode the room thermostat (RT) circuit must be closed * In case Heating mode is selected the water temperature in the system must be lower than (the pre-set one the hysteresis ), * In case a mode with DHW production has been selected the temperature in the water tank must be lower than (the pre-set one - the hysteresis ) 15.03.2015 11:25 Старт 60 sec 15.03.2015 11:25 Запалване 60 sec 23 C 80 23 C 80 Ignition of the burner. When holding the button Start/Stop for more than 3sec., automatic operation is started. * the fan comes on at maximum capacity, to clean the stove for a time, pre-set by a parameter; * simultaneously, an external auger for initial filling (if one is connected) is switched on and the pellet level sensor reads lack of pellets in the pipe of the burner. * After expiry of the programmed time, the heater comes on; Ignition In ignition mode: *Maximum time for the ignition cycle (parameter) is loaded; * Fan capacity is reduced to the value, pre-set by a parameter. *Dosing auger is started for the initial filling with pellets of the firebox (time is preset by a parameter) Required conditions to move to the next mode: *Photosensor reads presence of burning fire (pre-set by parameter). Successful ignition. Heater is switched off. The mode is changed to <Burning up>; *Expiry of the time for ignition unsuccessful ignition. Starting Repeated ignition mode with reduced quantity of pellets. *After a number of unsuccessful ignitions (pre-set by parameter), it switches off the heater and the mode is changed to <Cleaning> 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 15/25
15.03.2015 11:25 Разгаряне 60 sec 23 C 80 15.03.2015 11:25 P1 Модулация 60 sec 23 C 80 15.03.2015 11:25 STOP Спиране 60 sec 23 C 80 Burning up Transitory mode to establish stable burning process. *Loads time for this mode (parameter) *Fan capacity fan is set by a parameter; *Up and down time of the feeding auger is pre-set by parameter; Required conditions to move to the next mode: *expiry of the pre-set time *Monitors the parameters of the photosensor. When values fall below emergency threshold Extinguished flame, the stove goes to <Cleaning> mode *Monitors the temperature of the water in the system. When values exceed a threshold (parameter), the circulation pump is switched on. *Monitors the readings at the input of fan speed. When value falls below 100 rpm it triggers an alarm. Mode <Modulation> Three-stage control of the burner s heating capacity (Р1,Р2,Р3) and mode (Smoldering combustion) when the burner is maintained in a state of readiness for modulation, if required. Smoldering combustion is a mode, which is to be pre-set by time, and if after the expiry of the smoldering combustion time, no request for modulation is sent, the burner goes into a Stopping mode. The controller determines the heating capacity of the stove depending on the temperature difference between the pre-set and the current temperature of the water in the system. For every stage of modulation there are parameters, which provide for quality combustion process with the different intensities of combustion or generation of different heating capacity, respectively. * The fan capacity is pre-set by parameter for each stage of modulation; Up and down time of the feeding auger is pre-set by parameter for each stage of modulation; * Monitors the parameters of the photosensor. When values fall below emergency threshold Extinguished flame, the stove goes to <Cleaning> mode *Monitors temperature of the water in the system. When values exceed a threshold (parameter) it switches on the circulation pump. * Monitors the readings at the input of fan speed. When value falls below 100 rpm it triggers an alarm. *When the burner has stopped but has passed the Smoldering combustion mode, it monitors the water temperature in the system. When it falls below the pre-set value of the hysteresis, the burner is re-started (ECO Mode) Mode <Stopping>: controlled extinguishing of the burner. *the fan and the feeding auger work with the same parameters as in mode of modulation P1; There are three options to go into <Stopping> mode: - Press and hold button Start/Stop for 3 sec. - ECO mode the pre-set temperature has been reached the burner stops and starts again only when the water temperature falls below (the preset temperature - hysteresis) - Emergency stopping caused by an event, which results in triggering an alarm. Required condition to move to the next mode: *The photosensor readings fall below a threshold, set by a parameter. 15.03.2015 11:25 Почистване 60 sec 23 C 80 <Cleaning> Mode It is activated with the expiry of the pre-set time for cleaning of each of the modulation stages. Cleaning is also activated once <Stopping> mode is complete or in case of an emergency. *Fan operates at its full capacity until the pre-set time for this mode expires. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 16/25
9. Main menu structure 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 17/25
5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 18/25
5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 19/25
5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 20/25
10. Emergency situations The controller of PPB20/30/50 burner runs a priority parallel process of following the emergency situations occurred. The emergency situations are indicated by an acoustic signal and message displayed at the control panel. In the middle of the screen the icon! E remains active, to inform about the current emergency situation. To see the latest alarms or to clear the alarm messages, use the respective menu. In case of an emergency shut down the burner, eliminate the reason for the emergency situation and re-start the burner in accordance with the procedures. The alarms that can be displayed by the control panel, the possible reasons for their occurrence and the possible variants for their elimination are described below: EMERGENCY SITUATIONS ALARM MESSAGES MESSAGES EMERGENCY SITUATION POSSIBLE REASONS CORRECTIVE ACTIONS 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 21/25
Interrupted power supply Interruption of the power supply. The burner continues working in modulation mode, and only the message is displayed Interruption of the power supply The burner passed through cleaning mode and it is in Standby mode Extinguished fire The photosensor reads parameters above the pre-set threshold during operation. The burner goes into <Stopping> mode Unsuccessful ignition Water temperature sensor fault DHW temperature sensor fault Fan fault It occurs upon expiry of the time for ignition and the respective number of repeated attempts It occurs when the water temperature sensor is faulty. The burner goes into <Stopping> mode It occurs when the DHW temperature sensor is faulty. The burner goes into <Stopping> mode It occurs in case of faulty fan or when the fan stops. The burner goes into <Stopping> mode Short-time interruption of the power supply, but the photosensor reads presence of fire No power supply during operation No power supply during operation. The photosensor does not detect fire upon the following resuming of the power supply. - poor combustion processes - lack of pellets - sub-quality pellets Damaged heater Wrong settings. Sub-quality pellets Temperature sensor fault Interrupted connections of the sensor Controller fault Temperature sensor fault Interrupted connections of the sensor Controller fault Fan fault Fan speed sensor fault. Controller fault Check the main power supply of the burner Check the main power supply of the burner Check for presence of pellets Check the settings of burning mode Clean the firebox. Check the heater Check the settings Procedure to be performed by a servicing! Replace the sensor Replace the controller Procedure to be performed by a servicing! Replace the sensor Replace the controller Modification of the parameters Replace the fan Replace the sensor Replace the controller 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 22/25
11. Factory settings: Parameters Value Limits Ignition 1. Duration 60 sec 1000 sec 2. Fan 20% 100% 3. Initial filling 20 sec 150 sec 4. Auger feeding 1 sec 5 sec 5. Auger interval 5 sec 120 sec 6. External auger 10 sec 150 sec 7. Flame sensor on 0 600 8. Flame sensor off 0 600 9. Repeat 0 3 10. Repeated filling 20 sec 150 sec 11. Temperature of exhaust gases 30 ⁰С 60 ⁰С 12. dt 5 ⁰С 15 ⁰С Burning up 13. Duration 30 sec 1000 sec 14. Fan 20% 100% 15. Auger feeding 1 sec 5 sec 16. Auger interval 5 sec 120 sec Modulation P1 17. Fan 20% 100% 18. Auger feeding 1 sec 5 sec 19. Auger interval 5 sec 60 sec 20. Temperature Difference dt 0 ⁰С 20 ⁰С 21. Cleaning interval 1 sec 120 sec 22. Modulation P2 23. Fan 20% 100% 24. Auger feeding 1 sec 5 sec 25. Auger interval 5 sec 60 sec 26. Temperature Difference dt 0 ⁰С 20 ⁰С 27. Cleaning interval 1 sec 120 sec Modulation P3 28. Fan 20% 100% 29. Auger feeding 1 sec 5 sec 30. Auger interval 5 sec 60 sec 31. Temperature Difference dt 0 ⁰С 20 ⁰С 32. Cleaning interval 1 sec 120 sec Modulation P0 (Smoldering combustion) 33. Fan 20% 100% 34. Auger feeding 1 sec 5 sec 35. Auger interval 5 sec 60 sec 36. Temperature Difference dt 0 ⁰С 20 ⁰С 37. Cleaning interval 1 sec 120 sec Cleaning 38. Initial cleaning 30 sec 600 sec 39. Extinguishing 100 sec 1500 sec 40. Automatic cleaning Temperatures 41. Boiler temperature 40 ⁰С 85 ⁰С 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 23/25
42. Hysteresis 2⁰С 10 ⁰С 43. DHW temperature 30 ⁰С 70 ⁰С 44. Hysteresis 2⁰С 10 ⁰С Water pump 45. Temperature of switching on 30 ⁰С 70 ⁰С 46. Hysteresis 2⁰С 10 ⁰С 47. DHW temperature of switching on 30 ⁰С 70 ⁰С 48. Hysteresis 2⁰С 10 ⁰С 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 24/25
12. WARRANTY TERMS AND CONDITIONS The manufacturer warrants the correct and flawless operation of the product only if all requirements for installation and operation, commissioning and maintenance service have been complied with. THE WARRANTY SHALL BE VOID if: - the requirements for installation and operation have not been complied with - an attempt for elimination of the defect has been made by the buyer or other unauthorized parties - the product s storage and transportation has not been properly done Every warranty repair must be entered in the warranty certificate. The warranty period shall be interrupted for the time from the defect claim to the fault elimination. The warranty shall only be valid in the presence of the purchase invoice and the original warranty certificate. LIST OF WARRANTY REPAIRS CARRIED OUT Date of admission in the service station Description of defect Date of hand over to the client Signature of the person that did the repairs The warranty period of the product is 24 months from the date of its sale from the commercial network, provided that all requirements for proper installation and operation have been complied with. 5100 Gorna Oryahovitsa, 4А Ivan Momchilov Street tel.:0879990 542 25/25