Glass Chimney Hood Installation & User Instructions Please keep for future reference 4897549 4897556 Important Please read these instructions fully before installing or using These instructions contain important information which will help you get the best from your appliance and ensure safe and correct installation, use and maintenance. If you need help or have damaged or missing parts, call the Customer Helpline: 0845 600 4632 Issue 1 16/09/2010
Contents Safety Information 2 Parts 3 Guide to Wall Mounting and fixings 4 Installation 5-9 Vent outside 5-7 Vent inside 8 Electrical Connection 9 User Instructions 10 Care and Maintenance 11 General 11 Light bulb replacement 11 Trouble Shooting 12 Technical Specifications 13 Disposal information 13 Guarantee 14 Product codes SY-3288B-P-C-600 SY-3288B-P-C-900 1
Safety Information Important Please read these instructions fully before installation Before use The installation of this appliance is best carried out by 2 people. Any installation work must be carried out by a qualified technician or competent person. Dispose of all packaging carefully and responsibly. The appliance is designed for indoor use only and must be protected from rain, moisture and extreme temperature variations. This appliance is designed for household use. Do not use the appliance for industrial and commercial use, or any other purpose. Do not modify the appliance as this could result in danger. When installing the hood, ensure that the following recommended distances are being observed between the cooker top and the bottom of the cooker hood: Electric cookers: 70 cm Gas cookers: 70 cm Coal/ oil cookers: 80 cm If the room where the cooker hood is to be used contains a fuel burning appliance such as a central heating boiler, the flue must be of a sealed or balanced flue type. The edges of the cooker hood are sharp take care when you handle your appliance, especially during installation and cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS! Always disconnect the cooker hood from the power supply before carrying out any work on the hood, including light bulbs replacement. Do not connect the ducting system of this appliance to any existing ventilation system which is being used for any other purpose. Do not install above a cooker with a high level grill. Carry out fumes discharging in accordance with the regulations in force by local laws for safety and technical restrictions. During use This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure that they do not play with the appliance. Adequate ventilation must be provided when the cooker hood and other non-electrical powered appliances are used at the same time. Ensure proper ventilation measures are being observed when hood is in extraction mode. Note that it removes odours from your room, not steam. Do not cook food over open flames or operate gas hobs without pots or pans under the hood as the flames may sucked into the hood causing damage. Always put lids on pots and pans when cooking on a gas cooker. Never leave frying pans or deep frying unattended during use as overheated fats and oils might catch fire. Dirty oil is an even greater fire risk. Never flambé cook under this cooker hood. Do not attempt to use the cooker hood if it is damaged in any way. Never attempt to use it without the grease filters fitted or if the filters are excessively greasy! The manufacturer refuses to accept any responsibility for damages arising to the hood or it s catching on fire from failure to observe safety advice in these instructions. Do not attempt to repair the appliance yourself. Contact the Customer Helpline: 0845 600 4632. 2
Parts If you have damaged or missing parts, call the Customer Helpline: 0845 600 4632 Please familiarize yourself with the parts and accessories listed below 1. Control panel 2. Light 3. Chimney 4. Glass 5. Filter Accessories included Instructions x 1 Glass x 1 (Fitted on SY-3288B-P-C-600) Chimney x 1 Exhaust Pipe x 1 One-way-valve x 1 Wall Bracket x 1 Plate I x 1 Plate II x 1 Screw x 7 Wall plug x 9 (4mm x 38mm) Screw x 8 (4mm x 8mm) Rubber cushion for glass x 4 (Fitted on SY- 3288B-P-C-600) Flat end Screw x 4 Screw x 2 (4mm x 22mm) (4mm x 30mm) (Fitted on SY-3288B-P-C-600) 3 Mat x 4 (Fitted on SY-3288B-P-C-600) Carbon filter (not included, purchase separately)
4
Installation Vent outside Caution: 2 people are required to unpack and handle the appliance, it is recommended that gloves are worn. Caution: The wall must be strong enough to take the weight of the hood. Wall plugs are provided to secure the hood to most types of walls. However, a qualified technician must verify the suitability of the materials in accordance with the type of wall. Do not tile, grout or silicone the appliance to the wall. Surface mount only. VENT OUTSIDE If you have an outlet to the outside, your cooker hood can be connected by means of a given exhaust pipe or any suitable extraction duct (enamel, aluminum, flexible pipe or inflammable material with an interior diameter of 150mm) Carefully remove all packaging materials including the foam base, dispose of correctly. Before installation, ensure that the unit is power off and unplug from the outlet. 1. The cooker hood should be placed at distance of 65~75cm above the cooking plane for the best effect. 2. Drill 3 holes to accommodate the wall bracket. Screw and tighten the wall bracket onto the wall with the screws (4mm x 38 mm) and wall plugs provided. 5
Installation Vent outside 3. Drill 2 holes to accommodate plate II. Screw and tighten the bracket onto the wall with the screws (4mm x 38 mm) and wall plugs provided. The distance between the wall bracket and plate II is suggested to be maximum 90cm. 3 Remark: Plate II is used to fix the chimney at the end of installation. Therefore, it is suggested that you refer to the whole installation procedure to locate the proper position of the plate II. The diagram at right is for illustration only. Fixing the chimney to wall plate is done at the end of installation. 4.Lift up the cooker hood and hang onto the wall bracket hook. 5. Fix the one-way-valve to the air outlet of the cooker hood by 4 screws (4mm x 8mm). Remark: Sponge tape sometimes covers the 4 holes. If the 4 holes are located below the sponge tape, simply insert the screw through the sponge tape. Then, attach the exhaust pipe onto the one-wayvalve as shown. 6. Place the rubber cushion into the holes of the glass. Place the glass in appropriate position on the top the cooker hood and fix with 4 flat end screws (4mm x 22mm). In order to avoid the glass cracking, please do not tighten the screws too strongly. (Not applicable to model SY-3288B- P-C-600) When the hood is being used in extractor function, ensure that the ducting is fire retardant and the bends is not greater than 90 degrees as this will reduce the efficiency of the hood. 6
Installation Vent outside 7. Adjust the height of the chimney approximately in according to your required height. Then, install plate I on the chimney with two screws (4mm x 8mm). The procedure is as below. a) Put the inner chimney into outer chimney. Then pulling out the inner chimney upwards. Adjust the chimney height as required approximately. Fine adjustment can be done later. b) Install plate I on the chimney with two screws provided (4mm x 8mm). NOTE: Remember not to fix the screw too tight, so that later height adjustment can be done easily. 8. Put the chimney to the cooker hood. Fine height adjustment can now be done. 9.Fix the chimney to plate II. Two screws (4mm x 8mm) are used. 9 10. Fix the body with safety screw. Two screws (4mm x 30mm) and two wall plugs are used. 7
Installation Vent inside If you do not have an outlet to the outside, exhaust pipe is not required and the installation is similar to the one shown in section VENT OUTSIDE. Activated carbon filter (purchase separately) can be used to trap odors. Contact the helpline for details. Fix the one-way-valve to the air outlet of the cooker hood by 4 screws (4mm x 8mm). In order to install the activated carbon filter, the cartridge filter should be detached first. Press the lock and pull it downward. Put the activated carbon filter into the side of the motor and turn it in anti-clockwise direction. Repeat the same on the other side of motor. NOTE: Make sure the filter is securely locked. Otherwise, it would loose and cause danger. When activated carbon filter attached, the suction power will be lowered. Contact helpline 0845 600 4632 to purchase the carbon filter. Carbon filters not included available separately 8
Installation Electrical connection Any electrical work that is required to install this appliance MUST be carried out by a qualified electrician. Warning: THIS APPLIANCE MUST BE EARTHED Before making any electrical connections, ensure that: Electrical safety is only guaranteed when the earth system of your house is in accordance with the related local regulations. Do not damage the refrigerant circuit. Do not bend, stretch or pull the supply cable to avoid electric shock. Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer. Ensure the power socket is suitable for the maximum power of the machine (fuses in the power circuit must be 13 amp). The supply voltage should be the same as that indicated in the technical specifications and the appliance rating plate. The appliance should be earthed and in compliance with the applicable law. When installed, the power socket must be within easy reach. If the socket outlets in your home are not suitable for the plug supplied with this unit check with a qualified electrician for replacement. The use of adapters, multiple connectors or extension cables are not recommended. The appliance must be connected to a 220-240 volt 50Hz AC supply by means of a three pin socket, suitably earthed and protected by a 13 amp fuse. Should the fuse need to be replaced, a 13 amp fuse approved to BS1363/A must be used. The plug contains a removable fuse cover that must be refitted when the fuse is replaced. If the fuse cover is lost or damaged, the plug must not be used until a replacement cover has been fitted or the plug is replaced. A damaged plug should be cut off as close to the plug body as possible, the fuse should be removed and the plug disposed of safely. Plug replacement (UK & Ireland only) Should you need to replace the plug; the wires in the power cable are coloured in the following way: Blue Neutral N Brown Live L Green & Yellow Earth E As the colours of the wires in the power cable may not correspond with the coloured markings identifying the terminals in your plug, and proceed as follows: The green & yellow wire must be connected to the terminal in the plug that is marked with the letter E or by the earth symbol. The blue wire must be connected to the terminal that is marked with the letter N. The brown wire must be connected to the terminal that is marked with the letter L. If power supply cord is damaged, it must replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard. 9
User Instructions Using your appliance Switch off button Press this button to stop the motor operation. Low Speed button Press this button to operate at low speed. Medium Speed button Press this button to operate at medium speed. High Speed button Press this button to operate at high speed. Light button Press once, two lighting lamps will illuminate. Press again will turn all lights off. It is recommended that the cooker hood is switched on for 5 minutes prior to cooking and to leave in operation during cooking. Leave for another 10 minutes after finish the cooking. 10
Care and Maintenance General Important: Always unplug the appliance from the power socket during cleaning and maintenance. Never use any sharp instruments or abrasive substances, soap, household cleaner, detergent or wax polish for cleaning. Regular Cleaning Use a soft cloth moistened with hand-warm mildly soapy water or household cleaning detergent. Never use metal pads, chemical, abrasive material or stiff brush to clean the unit. Monthly Cleaning for Cartridge Filter ESSENTIAL: Clean the filter every month can prevent any risk of fire. The filter collects grease, smoke and dust so the filter would directly affect the efficiency of the cooker hood. If not cleaned, the grease residue (potential flammable) will saturate on the filter. Clean it with household cleaning detergent. Annual Cleaning for Activated Carbon Filter Apply SOLELY to unit that installed as a recirculation unit (not vented to the outside). The filter traps odours and must be replaced at least once a year depending on how frequent the cooker hood used. Warning: Failure to carry out the basic standards of the cleaning of the appliance and replacement of the filters may cause fire risks. Light bulb replacement 1. Switch the unit off and pull out the plug first. 2. Wait until the light bulb is cooled down before replacement. 3. Remove the chrome rims by turning in anticlockwise direction. 4. Pull out the halogen light bulb carefully and replace by same type and same rated halogen light bulb (12V G4 base 20W MAX). 5. Assembly the chrome rims back to the unit. 11
Trouble Shooting In the unlikely event of difficulties with your appliance please follow the trouble shooting guide below. If the problem persists, contact the retailer if the machine is still under guarantee. If the machine is out of guarantee, contact an approved service agent on 0845 600 4632. Problem Possible cause Solution The hood does not work Suction performance not good Power outage Speed not selected Too long distance between the unit and the cooking top Improper motor speed Dirty filter Check the power supply Press the speed button to activate Readjust the distance to 65-75cm Select the speed sufficient for the quantity of fumes presented Clean the filter under section Care and Maintenance No light Light bulb burnt Replace the bulb with correct rating 12
Technical Specifications Model SY-3288B-P-C-600 SY-3288B-P-C-900 Product width SY-3288B-P-C-600 60CM SY-3288B-P-C-900 90CM Fan speed level 3 Maximum extraction 700 m 3 /hr Lamps Halogen 20W X 2 Washable grease filters Adjustable chimney 5 layers We apologise for any inconvenience caused by any minor inconsistencies in these instructions, which may occur as a result of product improvements and development. Yes This appliance complies with the following EEC directives: 2006/95/EEC Low voltage directive 2004/108/EEC EMC directive Disposal information The symbol on the product or its packaging indicates that this product may not be treated as household waste. Instead it should be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling this product, please contact your local council office, your household waste disposal service or the shop where the product was purchased. 13
Guarantee PRODUCT GUARANTEE This product is guaranteed against manufacturing defects for a period of Year This product is guaranteed for twelve months from the date of original purchase. Any defect that arises due to faulty materials or workmanship will either be replaced, refunded or repaired free of charge where possible during this period by the dealer from whom you purchased the unit. The guarantee is subject to the following provisions: The guarantee does not cover accidental damage, misuse, cabinet parts, knobs or consumable items. The product must be correctly installed and operated in accordance with the instructions contained in this manual. It must be used solely for domestic purpose. The guarantee will be rendered invalided if the product is re-sold or has been damaged by inexpert repair. Specifications are subject to change without notice. The manufacturer disclaims any liability for the incidental or consequential damages. The guarantee is in addition to, and does not diminish your statutory or legal rights. In the event of a problem with the product within the guarantee period call the Customer Helpline on 0845 600 4632. Guarantor: Home Retail Group 489-499 Avebury Boulevard Central Milton Keynes MK9 2NW